EMS Xtreme4mx User Manual

 

 

Xtreme

4

mx  

4x4   HDMI   Scaler   Matrix   with   video   wall   function  

User   Manual

1    

Safety   and   Notice    

 

 

 

 

Please   read   all   of   these   instructions   carefully   before   you   use   the   device.

  Save   this   manual   for   future   reference.

 

The   XTREME4MX   4x4   HDMI™   Scaler   Matrix   with   video   wall   function   has   been   tested   for   conformance   to   safety   regulations   and   requirements,   and   has   been   certified   for   international   use.

  However,   like   all   electronic   equipments,   the   XTREME4MX   should   be   used   with   care.

  Please   read   and   follow   the   safety   instructions   to   protect   yourself   from   possible   injury   and   to   minimize   the   risk   of   damage   to   the   unit.

 

 Follow   all   instructions   and   warnings   marked   on   this   unit.

 

 Do   not   attempt   to   service   this   unit   yourself,   except   where   explained   in   this   manual.

 

 Provide   proper   ventilation   and   air   circulation   and   do   not   use   near   water.

 

 Keep   objects   that   might   damage   the   device   and   assure   that   the   placement   of   this   unit   is   on   a   stable   surface.

 

 Use   only   the   power   adapter   and   power   cords   and   connection   cables   designed   for   this   unit.

 

 Do   not   use   liquid   or   aerosol   cleaners   to   clean   this   unit.

  Always   unplug   the   power   to   the   device   before   cleaning.

   

 

 

  2  

 

Introduction  

  The   XTREME4MX   4x4   HDMI™   Scaler   Matrix   with   video   wall   function   provides   the   most   flexible   and   cost   effective   solution   in   the   market.

  The   new   XTREME4MX   can   be   used   as   a   conventional   matrix   swtich,   routing   up   to   4   different   HDMI   video   sources   to   any   monitor   independently   or   be   used   as   video   wall   processor,   splitting   a   chosen   image   from   4   sources   to   4   displays.

  On   top   of   that,   it   can   work   as   "combo"   gear,   showing   any   individual   input   source   in   full ‐ screen   for   any   selected   display   while   other   displays   are   working   in   video   wall   mode.

 

 

FEATURES  

 HDCP   compliant  

 Allows   any   HDMI   display   to   view   any   HDMI   source   at   any   time  

 Supports   7.1

  channel   digital   audio  

 Supports   default   HDMI   EDID   and   learns   the   EDID   of   displays  

 The   matrix   master   can   switch   every   output   channels   to   any   HDMI   inputs   by   push ‐ in   button,   IR   remote   control,   RS ‐ 232   control,   and   Ethernet   control  

 Easy   installation   with   rack ‐ mounting   and   wall ‐ mounting   designs   for   master   and   receiver   respectively  

 Fast   response   time   for   channel   switch  

 Four   HDMI   outputs   from   640x480   to   1920x1200  

 Supports   HDMI/   DVI   input,   from   640x480   to   1920x1080@60,   interlaced   or   progressive  

 Resize,   position,   zoom,   rotation,   fade ‐ in   fade ‐ out   output   video  

 Each   HDMI   output   has   an   independent   controllable   display   area  

 User ‐ selectable   output   settings,   up   to   1920x1200  

 Image   parameters   and   layouts   are   automatically   saved   in   flash   memory   of   the   device   and   can   be   recalled   for   later   use  

 Several   Image   parameters   and   layouts   can   be   saved   in   computers   and   can   be   loaded   for   later   use  

 Software   control   through   RS ‐ 232   and   Ethernet  

 Firmware   upgradable   for   support   of   new   features   and   technology   enhancements  

 1U   size  

 

Package   Contents  

 

 1x   XTREME4MX  

 1x   IR   Receiver  

 1x   DC   12V   5A  

 1x   IR   Remote   control  







1x

1x

1x  

 

 

Rack

Installation

User  

‐ mounting

  software

Manual

  ear  

 

*   Additional   IR   remote   controllers   and   IR   blasters   can   be   purchased   as   optional   accessories   to   control   the   HDMI   sources   located   separately.

    set

 

 

CD  

  3  

 

Hardware   Installation  

XTREME4MX   as   master  

1.

  Connect   all   sources   to   HDMI   Inputs   on   the   4x4   HDMI   Matrix   XTREME4MX.

 

2.

  Connect   all   display   to   HDMI   Outputs   on   the   4x4   HDMI   Matrix   XTREME4MX.

 

 

3.

  Connect   the   +12V   5A   DC   power   supply   to   the   4x4   HDMI   Matrix   XTREME4MX  

Before   Installation  

 Put   the   product   in   an   even   and   stable   location.

  If   the   product   falls   down   or   drops,   it   may   cause   an   injury   or   malfunction.

 

 Do   not   place   the   product   in   too   high   temperature   (over   50°C),   too   low   temperature   (under   0°C)   or   high   humidity.

   

 Use   the   DC   power   supply   unit   with   correct   specifications.

  If   inappropriate   power   supply   is   used   then   it   may   cause   a   fire.

 

 Do   not   twist   or   pull   by   force   ends   of   the   cable.

  It   can   cause   malfunction.

 

 

EDID   LEARNING  

The   EDID   learning   function   is   only   necessary   whenever   you   encounter   any   display   on   the   HDMI   output   port   that   cannot   play   audio   and   video   properly.

  Because   the   HDMI   sources   and   displays   may   have   various   level   of   capability   in   playing   audio   and   video,   the   general   principle   is   that   the   source   will   output   the   lowest   standards   in   terms   of   audio   format   and   video   resolutions   to   be   commonly   acceptable   among   all   HDMI   displays.

  In   this   case,   a   720p   stereo   HDMI   signal   output   would   be   probably   the   safest   choice.

  Nevertheless,   the   user   can   force   the   matrix   to   learn   the   EDID   of   the   lowest   capable   HDMI   display   among   others   to   make   sure   all   displays   are   capable   to   play   the   HDMI   signals   normally.

 

 

There   is   a   method   to   do   EDID   Learning   as   below:  

 

Software   Control:   Please   refer   to   the   Operation   Approach\   Software   Control   through   RS ‐ 232   port   (Page   15.)  

There   are   six   embedded   default   EDIDs   as   below,  

 

1.

Full ‐ HD(1080p@60) ‐ 24bit   2D   &   2ch  

2.

Full ‐ HD(1080p@60) ‐ 24bit   2D   &   7.1ch

 

3.

HD(1080i@60)   (720p@60) ‐ 24bit   2D   &   2ch  

4.

HD(1080i@60)   (720p@60) ‐ 24bit   2D   &   7.1ch

 

5.

Full ‐ HD(1080p@60) ‐ 30bit   2D   &   2ch  

6.

Full ‐ HD(1080p@60) ‐ 30bit   2D   &   7.1ch

 

 

 

  4  

 

Panel   Descriptions  

FRONT   PANEL   —   XTREME4MX,   transmitting   unit   (TX)  

 

 

 

 

 

 

 

 

1.

Source   Status:   Input   source   indicator   LED  

2.

IR   SENSOR:   IR   sensor   for   receiving   the   IR   commands   from   IR   remote  

3.

Output   Push   Button   &   7 ‐ segment   LED:   Front   panel   push   buttons   used   to   select   the   number   of   display   channel   &  

LED   display   for   output   ports  

4.

Input   Push   Button   &   7 ‐ segment   LED:   Front   panel   push   buttons   used   to   select   the   number   of   input   source   &   LED   display   for   input   channels  

 

REAR   PANEL   —   XTREME4MX,   transmitting   unit   (TX)  

5.

+12V   DC:   12V   DC   power   jack    

6.

RS ‐ 232:   RS ‐ 232   control   port  

7.

Ethernet:   Ethernet   control   port    

8.

INPUT   1 ‐ 4:   HDMI   inputs  

9.

USB   5V:   output   5v  

10.

Output   1 ‐ 4:   HDMI   outputs  

 

11.

USB   5V:   output   5v  

 

 

 

 

 

  5  

 

Operation   approach  

 

 

Method   A:Mode   Selection   preset   learn  

 

 

1.

IN/OUT   MAP  

1) Use   the   “+”or   “ ‐ “   output   push   button   to   select   the   number   of   display   save   default  

 

2) Use   the   “+”or   “ ‐ “   input   push   button   to   select   the   number   of   input   source  

“+”:   change   selected   input/output   port   in   ascending   order  

“ ‐ ”   :   change   selected   input/output   port   in   descending   order  

After   you   select   the   desired   input/output   port,   the   LED   will   blink   twice   and   the   setting   will   be   effective  

 

2.

Save   Mapping   Mode  

1) Keep   pushing   “output+   (save)”button   until   the   output   LED   shows   “d.”   to   enter   the   Save   Mapping  

Mode.

   

2) Use   the   “+”or   “ ‐ “   input   push   button   to   select   the   mapping   configuration   (0~7)   which   you   want   to   save   current   input/output   mapping  

3) After   you   select   the   desired   mapping   configuration   number,   the   LED   will   blink   twice   and   the   mapping   setting   will   be   saved  

4) If   you   push   the   “output ‐  (preset)”button   before   the   mapping   setting   is   saved,   the   LED   will   show  

“ 一 ”“ 一 ”to   quit   the   Save   Mapping   Mode  

 

3.

Preset   Mapping   Mode  

1) Keep   pushing   “output ‐  (preset)”button   until   the   output   LED   shows   “P.”   to   enter   the   Preset   Mapping  

Mode.

   

2) Use   the   “+”or   “ ‐ “   input   push   button   to   select   the   saved   mapping   configuration   (0~7)   which   you   want   to   recall  

3) After   you   select   the   desired   mapping   configuration   number,   the   LED   will   blink   twice   and   the   mapping   setting   will   be   effective  

4) If   you   push   the   “output+   (save)”button   before   the   mapping   setting   is   effective,   the   LED   will   show  

“ 一 ”“ 一 ”to   quit   the   Preset   Mapping   Mode  

  6  

4.

Default   EDID   Mode  

2) Push   “input+   (default)”button   to   select   the   input   channel   which   you   want   to   learn   default   EDID   and   then   keep   pushing   “input+   (default)”button   when   you   select   your   desired   input   channel    

3) Push   the   “+”or   “ ‐ ”   output   push   button   and   then   the   LED   will   show   “E”“d”   one   time   to   enter   Learn  

Default   EDID   Mode  

4) Use   “+”or   “ ‐ ”   output   push   button   to   select   the   default   EDID   mode(1~8)  

5) Release   “input+   (default)”button   after   selecting   the   desired   default   EDID   mode,   and   then   the   LED   will   blink   twice   and   the   setting   will   be   effective  

6) It   will   quit   the   Learn   Default   EDID   Mode   if   you   push   the   “input ‐  (learn)”button   before   the   setting   is   effective  

7) The   LED   will   show   “0”“0”   if   the   setting   is   success  

          The   LED   will   show   “F”“F”   if   the   setting   is   failure  

5.

EDID   Learning   Mode  

1) Push   “input ‐  (learn)”button   to   select   the   input   channel   which   you   want   to   learn   EDID   from   HDMI   output   and   then   keep   pushing   “input ‐  (learn)”button   when   you   select   your   desired   input   channel    

2) Push   the   “+”or   “ ‐ ”   output   push   button   and   then   the   LED   will   show   “E”“L”   one   time   to   enter   Learn  

Output   EDID   Mode  

3) Use   “+”or   “ ‐ ”   output   push   button   to   select   the   output   port   number  

4) Release   “input ‐  (learn)”button   after   selecting   the   desired   output   port   number,   and   then   the   LED   will   blink   twice   and   the   setting   will   be   effective  

5) It   will   quit   the   Learn   Output   EDID   Mode   if   you   push   the   “input+   (default)”button   before   the   setting   is   effective  

 

 

6) The   LED   will   show   “0”“0”   if   the   setting   is   success  

The   LED   will   show   “F”“F”   if   the   setting   is   failure  

 

 

  7  

 

 

 

Method   B:   IR   Remote   Control  

OFF

ON  

 

Button

STATUS

MUTE

SAVE  

PRESET

  Function  

Standby   mode

Power   on   the   matrix   switcher  

Preset

Turn

Save

 

 

Preset

 

  output off   current  

  status output’s mapping  

  video mapping mode

 

  and   mode audio

 

 

DEFAULT   EDID Begin   default   EDID   selection  

LEARN   EDID Begin EDID   learning   from   one   output  

CLEAR

TAKE  

F1  

Clear   the

Trigger

Change

 

 

  the all previous

 

  previous output  

  IR to

 

 

  operation setting one  

  input  

  procedure

F2 *   Fast   switch   to   Video   Wall   2x2   or   Video   Wall   1x1  

 

1.

    In   /Out   Switch  

Push   the   button   on   the   checkerboard   to   select   Input   &   Output   port.

 

      Ex:   Select   Input   2   to   Output   3  

 Press   output   number   key   “3”   to   select   Output   3  

 Press   input   number   key   “2”   to   select   Input   2  

 

 

  8  

 

2.

    Example   of   function   key   

Operation  

Mute   Output  

Procedure  

Mute   +   A~D(Output   1~4) +   Take

1.

  Press   “MUTE”   button  

Ex:   Mute   Output   3   2.

  Press   number   key   “C”   to   select   Output   3  

Output   Status  

Ex:   Output   4  

(Input   2)  

3.Press

  “TAKE”   button  

Status   +   A~D(Output   1~4)   +   Take

1.Press

  “STATUS”   button  

2.Press

  number   key   “D”   to   select   Output   4

3.Press

  “TAKE”   button  

Save   Current   Mapping   Save +   A~H(1 ‐ 8   storage   site) +   Take

1.Press

  “SAVE”   button  

Ex:   Save   current   mapping   to  

5   2.Press

  number   key   “E”   to   select   the   storage   site   5  

Preset   Mapping  

3.Press

  “TAKE”   button

Preset   +   A~H(1 ‐ 8   storage   site) +   Take

1.Press

  “PRESET”   button  

Ex:   Preset   saved   mapping   from   5  

Learn   default   EDID  

2.Press

  number   key   “E”   to   select   the   storage   site   5  

3.Press

  “TAKE”   button

Default   EDID   +   A~H(1 ‐ 8   default   EDID) + I~IV(input   1~4) +   Take

1.Press

  “DEFAULT   EDID”   button  

Ex:   Default   EDID   2  

Input   3  

2.Press

  number   key   “B”   to   select   default   EDID   2  

3.Press

  number   key   “ Ⅲ ”   to   select   Input   3  

Learn   EDID   Port   EDID  

4.Press

  “TAKE”   button  

Learn   + A~D(EDID   Port) + I~IV   (input   1~4) +   Take

1.Press

  “LEARN”   button  

Ex:   Learn   EDID   to  

  Input   3  

2.Press

  number   key   “D”   to   select   Output   4  

3.

  Press   number   key   “ Ⅲ ”   to   select   Input   3  

 

Select   All   Outputs   to   One  

Input  

4.Press

  “TAKE”   button  

F1   +   I~IV   (input   1~4)

1.Press

  “F1”   button  

  +   Take

 

Ex:   All   Outputs   to   Input   3  

2.

  Press   number   key   “ Ⅲ ”   to   select   Input   3

3.Press

  “TAKE”   button

 

Video   Wall   Mode   (2x2   and  

1x1)  

F2  

1.Select

  all   outputs   to   input   3   ( F1+ Ⅲ +   Take)

   

Ex:   2x2   Video   Wall     mode   on   Input   3:    

2.

  Press   F2   to   2x2   mode

3.Press

  F2   again   back   to   1x1   mode

 

A  

‐  

 

A  

3  

A  

3  

A  

 

3  

VFD   Window  

4  

2  

  d  

‐ 

‐ 

‐ 

4  

‐ 

 

3  

0  

3  

0  

 

‐ 

0  

 

P  

‐ 

P  

5  

 

  d  

5  

 

E   d  

2   d  

2  

3  

0                         F

0   (success)       F (fail)  

 

E  

L  

4  

L  

4  

3  

0                         F

 

0   (success)       F(fail)  

  9  

Software   Control   through   RS ‐ 232   port   /   Ethernet   port  

System   Requirement   and   Precautions  

 

1.

Whenever   power   off   XTREME4MX,   please   stay   unpowered   at   least   5   to   10   seconds   to   allow   power   capacitors   to   discharge.

   

2.

The   XTREME4MX   provides   software   control   program   which   runs   under   Microsoft   Windows   98,   2000,   XP,   7   through   the   interface   of   RS ‐ 232   serial   control.

 

3.

Before   you   click   on   the   icon   of   the   software,   make   sure   you   have   secured   the   connection   between   your   computer   COM   port   and   the   XTREME4MX.

 

Start   the   software   control   program  

When   clicking   on   the   executable   file,   the   following   dialog   will   pop ‐ up.

  It   has   two   ways   to   control   the  

XTREME4MX   device   (under   Microsoft   Windows   7,   please   run   as   administrator).

 

 

Step   1:   Select   RS ‐ 232   or   Ethernet   connection.

 

Step   2:   Select   COM   port   connection.

 

 

System:  

 

 

 

 

 

 

10  

Quick   Selection:   Get   a   quick   setting   from   default  

(a) Select   the   type   of   Rotation   if   requires   (   Default   is   none)  

 1x3:   This   mode   will   split   the   screen   into   3   parts   and   rotate   the   figure.

 

 1x4:   The   mode   will   split   the   screen   into   4   parts   and   rotate   the   figure.

 

*Notice   that   the   Rotation   and   the   split   configuration   cannot   do   simultaneously.

 

 

 

Video   Wall   setting  

(a) Select   the   output   port   and   resolution  

 

 

 

 

 

 

 

(b) Select   the   part   you   want   to   show   on   display  

 User   Set:  

User   can   define   how   many   cut   in   both   direction   (enter   1~4)   and   the   part   want   to   show   on   display.

 

Read   the   configuration   of   User   Set,   please   click   the     button.

 

  11  

 

 

 

For   example:   where   is   4 th

  cut   in   a   3x2   layout?

 

 

 

 

 

 

 

 

V  

 

1  

H  

2 3

 

 

 

 

4   5 6

 

 

Besides,   user   can   save   the   figuration   into   the   device   for   future   using.

 

 

 

 Load   from   file:  

User   can   load   the   configuration   from   the   existing   file.

  Next,   select   the   “Load   from   file”   mode   and   click   the  

  button   to   load.

 

 

 

  12  

Adjust   the   image   on   the   display  

(a) Fine   tune:  

You   can   arbitrary   move   the   image   on   each   screen   in   four   directions   through   the   button,   every   move   is   one   pixel   per   row   or   column.

 

 

(b) Masking:  

 

You   can   block   a   pixel   per   row   or   column   from   the   edge   in   four   directions   through   the   button,   and   the   image   will   be   auto ‐ scaling   to   fulfill   the   screen.

 

 

Monitor   the   effect   on   the   display  

This   area   will   demonstrate   the   resulting   selection   of   the   input   video   to   be   display   for   the   selected   output   channel.

 

The   bottom   part   of   this   area,   user   can   check   each   portion   from   the   original   input   that   response   to   each   display.

 

 

 

 

 

 

13  

Network  

User   also   can   use   the   Ethernet   to   control   software   program.

  First,   user   should   click   the   “Network”   option   to   open   the   Ethernet   Set.

  Next,   user   can   read   the   Ethernet   setting   from   device   or   manually   set   to   device.

 

 

After   the   step   of   Ethernet   Set,   user   can   select   the   connect   the   software   program   by   Ethernet.

 

  button   and   key   in   the   device   IP   address.

  Then,   they   can  

 

 

 

 

 

  14  

EDID   Management  

(a) Learn   EDID   from   Default  

 Select   default   EDID   mode.

 

 Select   input.

 

 Click   “Learn”   button   to   learn   default   EDID.

 

(b) Learn   EDID   from   Display  

 Select   the   output   EDID   mode.

 

 Select   input.

 

 Click   “Learn”   button   to   learn   EDID   from   display.

 

(c) Learn   EDID   from   File  

 Select   input  

 Click   “Load”   button   to   select   the   EDID   file   and   write   it   into   input.

 

(d) View   EDID   content  

 Select   the   EDID   input   source   (Input,   Output   or   From   File)  

 Click   “View”   button   to   read   the   EDID   description   and   analysis.

 

 Click   “Save   as...”to   save   the   EDID   as   a   file   on   computer.

 

 

 

 

 

 

15  

System  

(a) Firmware   Update  

Before   firmware   update   step.

  Please   make   sure   your   RS ‐ 232   is   connecting   and   the   connecting   state   is  

“Connected”.

  User   can   load   the   firmware   file   which   they   want   to   update.

  Click   “Start”   button   and   the   firmware   will   start   to   update.

 

 

(b) Factory   Reset  

 Click   “Factory   reset”   button   to   do   factory   default   reset.

 

 

 This   default   reset   process   will   take   about   10   seconds.

 

 

 After   pop ‐ up   a   dialog   indicates   complete,   please   restart   this   machine.

 

 

 

 

 

About  

Read   the   software   and   firmware   version/  

  16  

 

Specifications  

 

Item  

Role   of   usage  

HDCP   compliance  

Video   bandwidth  

Video   support  

Video   Format   Support  

Video   loop ‐ out  

Audio   support  

ESD   protection  

PCB   stack ‐ up  

Input  

Output  

Control  

Input   TMDS   signal  

HDMI   connector  

USB   connector  

RS ‐ 232   connector  

RJ ‐ 45   connector  

 

 

Environmental  

Fixedness  

Power   supply  

Operating   Temperature  

Storage   Temperature  

Relative   Humidity  

 

Description  

True   4x4   matrix  

Yes  

Single ‐ link   225MHz   [6.75Gbps]  

480i   /   480p   /   720p   /   1080i   /   1080p60   /   1920x1200@60Hz     30 ‐ bit   color  

HDMI/DVI  

No  

Surround   sound   (up   to   7.1ch)   or   stereo   digital   audio  

Human   body   model   —   ±12kV   [air ‐ gap   discharge]   &   ±5kV   [contact   discharge]  

8 ‐ layer   board   [impedance   control   —   differential   100 Ω ;   single   50 Ω ]  

4x   HDMI   /   1x   RS ‐ 232   /   1x   Ethernet  

4x   HDMI   /2x   USB  

RS ‐ 232/Ethernet/Front   Panel  

1.2

  Volts   [peak ‐ to ‐ peak]  

Type   A   [19 ‐ pin   female]  

Type   A   for   power   supply  

DE ‐ 9   [9 ‐ pin   D ‐ sub   female]  

WE/SS   8P8C   with   2   LED   indicators  

1U   rack ‐ mount   with   ears   and   Wall   hanging   holes  

12V   5A   DC  

0~40°C   [32~104°F]  

‐ 20~60°C   [ ‐ 4~140°F]  

20~90%   RH   (no   condensation)  

  17  

Warranty  

 

The   SELLER   warrants   the   XTREME4MX   4x4   HDMI™   Scaler   Matrix   with   video   wall   function   free   from   defects   in   the   material   and   workmanship   for   1   year   from   the   date   of   purchase   from   the   SELLER   or   an   authorized   dealer.

  Should   this   product   fail   to   be   in   good   working   order   within   1   year   warranty   period,   The  

SELLER,   at   its   option,   repair   or   replace   the   unit,   provided   that   the   unit   has   not   been   subjected   to   accident,   disaster,   abuse   or   any   unauthorized   modifications   including   static   discharge   and   power   surge.

  This   warranty   is   offered   by   the   SELLER   for   its   BUYER   with   direct   transaction   only.

  This   warranty   is   void   if   the   warranty   seal   on   the   metal   housing   is   broken.

 

Unit   that   fails   under   conditions   other   than   those   covered   will   be   repaired   at   the   current   price   of   parts   and   labor   in   effect   at   the   time   of   repair.

  Such   repairs   are   warranted   for   90   days   from   the   day   of   reshipment   to   the   BUYER.

  If   the   unit   is   delivered   by   mail,   customers   agree   to   insure   the   unit   or   assume   the   risk   of   loss   or   damage   in   transit.

  Under   no   circumstances   will   a   unit   be   accepted   without   a   return   authorization   number.

 

The   warranty   is   in   lieu   of   all   other   warranties   expressed   or   implied,   including   without   limitations,   any   other   implied   warranty   or   fitness   or   merchantability   for   any   particular   purpose,   all   of   which   are   expressly   disclaimed.

 

Proof   of   sale   may   be   required   in   order   to   claim   warranty.

  Customers   outside   Germany   are   responsible   for   shipping   charges   to   and   from   the   SELLER.

  Cables   and   power   adapters   are   limited   to   a   30   day   warranty   and   must   be   free   from   any   markings,   scratches,   and   neatly   coiled.

 

The   content   of   this   manual   has   been   carefully   checked   and   is   believed   to   be   accurate.

  However,   The  

SELLER   assumes   no   responsibility   for   any   inaccuracies   that   may   be   contained   in   this   manual.

  The   SELLER   will   NOT   be   liable   for   direct,   indirect,   incidental,   special,   or   consequential   damages   resulting   from   any   defect   or   omission   in   this   manual,   even   if   advised   of   the   possibility   of   such   damages.

  Also,   the   technical   information   contained   herein   regarding   the   XTREME4MX   features   and   specifications   is   subject   to   change   without   further   notice.

 

 

  web:   www.ems

‐ imaging.com,   email:   sales@ems ‐ imaging.com

 

  18