IR WATERPROOF D&N CAMERA

BAR70-M855

MANUAL

FEATURE

1. Long visible range at night.(70m Max. indoors, 60m Max. outdoors)

2. You can select the level ofLED ON/OFF and filter change according to Lux as follow.

- Default Setting LED ON : Approx.5Lux,LED OFF : Approx.

10Lux

3. This camera adopts split glass technology to prevent IR light reflection.

4. This camera has vari-focal IR lens to prevent defocusing under IR lighting.

5. Day & Night Function(ICR) at night to receive maximum available light.

6. This product can match for any circumstances very well.

7. This product is suitable for 24 hours survillance with optical multicoating filter according to IR LED and CCD.

8. This product is "waterproof" to resist rain, snow and other weather factors.(IP67)

9. Sunvisor of this product can help the camera get the picture clearly.

10. This product is made of corrosion-free surface to resist rust and corrosion for a long time.

11. RS-485 interface.(Pelco-D, Pelco-P protocol support)

12. Support 4 different privacy zone

13. DWDR(Digital Wide Dynamic Range)

14. Multi function : High Light Mask, Lens Shading Compensation, Impact

Detection,Motion Detection

15. Multi-language full OSD support

16. Power & video cables are concealable.(Cable through bracket)

17. This camera adopts 3-axis bracket to install on the ceiling and wall.

18. You can connect 24V AC or 12V DC regardless polarity.

(Dual power version only)

19. This camera supports the advanced high resolution.

(700 TV- Line Color)

20. You can adjust the level of IR LED according to the circumstances.

IR LED output level controllable via RS-485.

21. A heater enables the camera to keep the proper operation at low temperature.(ON : 23 ℃ , OFF : 28 ℃ )

22. A fan enables the camera to keep the proper operation when the

LED is ON.

CAUTION

1. Please study the instruction manual before your applications and keep it for your future reference.

2. Do not flash LED light directly on the eyes when LEDs are on.

3. Do not install the camera on a unstable surface. It will cause falling or other hazards.

4. Do not use improper power, it could cause fire or electric shock.

(Use the AC adaptor 12V DC regulated, 2A.

Dual voltage product can use 24V AC adaptor.(option))

5. Do not disassemble or re-model the camera, it could cause fire, electric shock or other hazards.

6. Stop using the camera when you find a malfunction like smoke or unusual heat, it could cause fire or electric shock.

7. Due to the possibility of water leakage, do not cut or peel off the cable.

In case you cutor peel off the cable, the warranty will be void.

8. Do not adhere dangerous articles to the camera.

9. Do not leave the unit along with an unstable stand or table.

10. DC power cable or video cable should be always loose.

Do not keep the cables tight or twisted.

11. Please use the camera unit within given temperature and electricity limit.

12. Please make sure that installation should be done by qualified service person only.

13. Do not disassemble the unit by yourself. When there is problem with the unit please contact after-sale service center or the shop where you bought.

If the product is to be put out of operation definitively, take it to a local recycling plant for a disposal which is not harmful to the environment.

ACCESSORIES

ANCHOR 8x35 4EA

SCREW 6x35 TP1PAN SUS 4EA

WRENCH 5mm L TYPE 1EA

BOLT 1/4"-20UNC L=6, 1EA

INSTALLATION

<Ceiling mount>

Ceiling

ANCHOR 8x35 4EA

<Wall mount>

SCREW Tp16x35 4EA

ANCHOR 8x35 4EA

SCREW Tp16x35 4EA

Wall

Ø 30

63

Ø 30

ADJUST THE DIRECTION & OPEN/CLOSE CAP

Wall

WRENCH 5mm

Unlock

Lock

DIRECTION ADJUSTMENT

If you need function setting, open and close the cap by using the wrench.

※ After mounting the camera on a wall or ceiling

1. Loosen a bolt by using the wrench included.

2. Face the direction ofthe camera to monitor.

3. Tighten a bolt to complete adjustment.

SPECIFICATION

Model No.

Image Sensor

Effective Pixel

Cell Size

Resolution

TV Type

Sync. Type

Scanning System

Video Output

Gamma Characteristic

Min. Illumination

OSD

Motion Detection

Impact Detection

White Balace

Privacy Zone

Day & Night

RS-485 Protocol

S/N Ratio

Mirror

Backlight

Reverse Polarity Protection

Control Interface

Gain Control

Shutter

Test Illuminance Area

Power Supply

Current Consumption

Lens

LED

Operation Temp.

Preservation Temp.

Dimension

Weight

BAR70-M855

1/3" SONY SUPER HAD CCD Ⅱ

768(H) X 494(V) PIXEL(NTSC), 752(H) X 582(V) PIXEL(PAL)

6.35

㎛ (H) X 7.4

㎛ (V)(NTSC), 6.5

㎛ (H) X 6.25

㎛ (V)(PAL)

COLOR : 700 TV-Line, B/W : 750 TV-Line

NTSC / PAL

Internal

2:1Interlace

1.0 Vp-p(Sync. Negative) Termination 75 Ω ± 10%

γ = 0.45(Adjustable)

0.01Lux(F/1.2), 0Lux(LED HIGH, 70M Range)

Full OSD

ON / OFF Selectable(64 Zone)

ON / OFF Selectable(3 Step : LOW / MIDDLE / HIGH)

ATW / AWC / MANUAL

ON / OFF Selectable(4 Zone)

ICR(AUTO, COLOR, B/W)

PELCO-D&P

48dB over(AGC OFF)

ON / OFF

DWDR / BLC / HLC / OFF

YES

Extra Video connector for easy installation

Automatic(Adjustable)

1/60 ~ 1/100,000sec(NTSC), 1/50 ~ 1/100,000sec(PAL)

Average test illuminance by front view

12V DC, 24V AC Dual Voltage(option)

Max. 1.3A

Vari-focal auto iris day & night lens

IR LED 70EA

-10 ∼ 50 ℃

-20 ∼ 60 ℃

141.9(W) X 80.2(H) X 183.3(D)mm

Approx. 1.7kg

FUNCTION SETTING

1. OSD menu structure

Function setting menu Select menu

LENS

Sub menu

MANUAL, DC

1. EXPOSURE

BRIGHT

DC LEVEL

E.SHUTTER

AGC

DWDR

BLC

HLC

HLC THR

Contents

0 ~ 100

0 ~ 20

AUTO

1/60(1/50) ~ 1/100,000

OFF, LOW,

MIDDLE, HIGH

OFF, LOW, MIDDLE, HIGH

OFF, ON

OFF, ON,

AUTO

0 ~ 100

Fixed focal lens or Vari-focal auto iris lens

In case of manual lens selection, adjust the brightness

In case of DC lens selection, adjust the brightness

Shutter speed auto adjustable

Select shutter speed manually

Determines that use the AGC function or not and AGC level selectable(You can not use the

Auto D&N change mode when AGC is off)

Digital Wide Dynamic Range

BLC function

High Light Mask function

In case of AUTO mode, the function will off in daytime and on at night

According to the threshold value, the camera will recognize as High light or not.

※ All specification is subject to change without notice to improve the quality.

2. WHITE

BALANCE

3. DAY&NIGHT

4. IMAGE

ADJUST

5. MOTION &

IMPACT

6. PRIVACY

MASK

7. COMMUNI-

CATION

8. SPECIAL

9. FACTORY

SET

10. EXIT

AWB MODE

D&N MODE

BURST

COLOR

B&W →

→ B&W

COLOR

DELAY TIME

ATW

MANUAL

AWC

AUTO

COLOR

B&W

↓

OFF, ON

85 ~ 170

50 ~ 135

3 ~ 15

Color temperature 2500 ~ 9500°K

Adjust the Red or Blue values to shift the color of the object

Move the camera lens toward to white paper then press the set button to find the optimal white balance for current environment

Auto day&night switching mode

Fixed at color(LED OFF)

Fixed at B/W(LED ON)

Determines whether to transmit the burst signal or not in B/W mode

You can select brightness of illumination about changing the day ↔ night mode

You can select the duration time about chaining the day ↔ night mode

LED LEVEL(IN/OUT)

DYNAMIC IR

MIRROR

SHARPNESS

GAMMA

LSC

LSC LEVEL

R-Y GAIN

B-Y GAIN

PATTERN

GENERATOR

MOTION

DISPLAY

OFF, LOW, MIDDLE, HIGH

OFF, ON

IR LED OFF/ON and output level adjustable

When IR LED is turned on in B/W, the objects can be clearly identified due to the function that decreases screen saturation of objects within a short distance.

Set a horizontal image inversion OFF, ON

0 ~ 50

0.45, 0.6, 1, USER

OFF, ON

Sharpness adjustable

Gamma adjustable

Determines whether to use the brightness compensation offour lens'corners(LSC) or not

The LSC level selectable 0 ~ 50

0 ~ 200

0 ~ 200

Adjust Red tone of the image

Adjust Blue tone of the image

Test signal. Press the set button, color bar appeared on the screen and press any key to return to menu

OFF, ON

Determines whether to use the motion detection function or not

NONE

MESSAGE

No display on the screen though movement is detected

The words 'MOTION' appear on the screen when movement is detected

SET

WINDOW

MASK

Motion detection area appear on the screen when movement is detected

Press the set button to move into the motion detection area section to set the 64 areas. Press the set button for a few second to move out

Press the set button to select all area ALL SET ↓

ALLCLEAR ↓

SENSITIVITY

HOLD TIME

IMPACT

HOLD TIME

MASK

1, 2, 3, 4

Press the set button to remove all area

0 ~ 255 Motion detection sensitivity

1~ 15

OFF, LOW,

MIDDLE, HIGH

Set the duration of outside alarm. If the way of display is message, it means display time of message

Determines whether to use impact detection function or not and sensitivity setting

1~ 15

OFF, ON

BLACK, GRAY…

Set the duration of outside alarm and display time of "IMPACT" message

Display each privacy mask or not. Press the set button to move into the privacy mask setting section, whenever you press the set button, the mask color is changed. When the mask color is red you can adjust the size by up, down, left and right button. When the mask color is blue you can set the position of mask by up, down, left and right button. Press the set button for a few second to escape

Select mask color MASK COLOR

CAM ID

BAUDRATE

PROTOCOL

1~ 255

2400 ~ 9600

PELCO-D, PELCO-P

Select the camera ID for RS-485 communication

Select baud rate

Select protocol

※ If you change the COMMUNICATION value through RS-485, you might not control the camera due to unmatched value(If your camera is out of working due to above reason, change your controller's value or wait a few minute till close the menu, it will be back to previous setting value)

LANGUAGE

NAME DISPLAY

EDIT

ENGLISH, … Select language

OFF, ON Display the camera ID on the screen

Press the set button to move into the name setting section. You can choose the letter by using up and down button and move next letter by using left and right button. Press the set button for a few second to move out

POSITION

Press the set button to move into the position setting section.

You can move the camera ID to your wanted position by using up, down, left and right button

To reset your camera to factory default condition

Notice : Lens, communication and language is not changed

Save the value and then restart

2. How to use the jog lever & Zoom/Focus trimmer

7

6

4

2

3

5

1

8

Focus & Zoom fixing screw

Focal length adjustment direction

1. Unfasten the '+' type screw inside

2. Adjust two trimmers properly

3. Tighten the scew

<Caution> When you tighten the screw, don't put stress excessively.

① Enter :

ㆍ Push the lever : Used to access the menu and confirm selection.

ㆍ Push the lever for one second : Used to return to previous menu from the motion detection setting section or privacy mask setting section.

② UP, ③ DOWN : Used to move the cursor to up or down.

④ LEFT, ⑤ RIGHT : Used to move the cursor to left or right and change the value.

⑥ EXT. VIDEO : Extra video output terminal for installation.

Plug your test monitor in hear. The cable is option.

⑦ Zoom, ⑧ Focus : Use a '+' type driver for adjusting zoom and focus.

3. How to control through RS-485 communication

1) Match the camera with controller's ID, baudrate and protocol

2) Up, Down, Left and right of Jog lever is same as Up, Down, Left and right of RS-485 controller

3) Enter of Jog lever is the same as menu key or IRIS open key of

RS-485 controller

4) Return to previous menu from motion detection setting section and privacy mask setting section : Iris close or Iris open for a few second. Or press the button as Up → Right → Down →

Left successively

4. Cable array (RS-485, ALARM)

A : BLUE(MOTION)

B : BLACK(GND)

C : GREEN(IMPACT)

D : BLACK(GND)

E : ORANGE(RX +)

F : WHITE(RX -)

E

F

C

D

No.

A

B

FUNCTION

MOTION ALARM

GND

IMPACT ALARM

GND

RX +

RX -

REMARK

ㆍ If the camera detected motion when using Motion & Impact function, outside line of motion alarm connect with GND(B).

ㆍ If the camera detect impact, outsie line of impact alarm connect with GND(D).Outputs of Motion & Impact are 'open collector'.

ㆍ Max current & voltage are 200mA and 30V DC.

RS-485A

RS-485B

<Caution> All connectors must be securely sealed to prevent water leakage, especially for un-used wires.