3- AXIS IR DOME CAMERA

DOIRP3000F

MANUAL

2. Removing the dome : Lift the dome. When you push the latch button, it is unlocked and you can lift the dome.

◐

PRECAUTION

1. Do not install the camera outdoors.

2. Choose an ideal location for the camera, since a camera unit must be protected against moisture and vibration.

3. Be careful not to scratch the camera unit, especially lens or dome cover.

4. Use the camera within the temperature(- 10 ~ +50).

5. Handle with care. Dropping it can cause serious damage to the camera.

6. Avoid any direct sun light toward the lens.

7. Use the AC adaptor 12V DC, 500mA regulated.

◐

FE ATURES

1. This camera is incredibly flexible to install with its 3- axis camera construction, which makes the camera ceiling, wall or slope mountable.

2. 15M range visible in tatal darkness with 14pcs of IR LED

3. RS- 485 interface(Pelco- D, Pelco- P protocol support) : option

4. Advanced High Resolution(600 TV- Line) : option

5. Support 4 different privacy zone

6. IR LED output level controllable via RS- 485

7. DWDR(Digital Wide Dynamic Range)

8. Multi function : High Light Mask, Lens Shading Compensation, Impact

Detection, Motion Detection

9. Multi- language full OSD support

◐

HOW TO INSTALL

1. Opening the dome : Pushing the latch button.

< C aution > Remove the protection sheet after installing.

PROTE CTION S HEET

LATCH BUT TON

3. Camera installation :

(1) Fix the camera set with the s upplied screws on ceiling or wall mount. If you don't use supplied screws, the camera may fall off.

(2) Please refer to '4. Camera angle adjustment' regarding adjust camera angle.

(3) Re- assemble the camera.

<Ceiling mount>

SCREW TP13.5x20 2EA

<Wall mount>

SCREW TP13.5x20 2EA

4. Camera angle adjustment :

(1) Pan adjustment : Grasp the disk of camera and then adjust

(2) Tilt adjustment : Grasp the led cover of camera and then adjust

(3) Roll adjustment : Grasp the camera holder and then rotate

<Caution> If you try to adjust the camera out of limited angle, it might cause troubles and damage to camera.

LED COVER

DISK

L

R

U

CAMERA HOLDER

D ROTATION

DIMENSION

Ø 85

ASSEMBLY

Ø 110

HARNESS

SCRE W

BUSHING RUB BER

SC REW

Ø 84

BODY

DOME COVER

BOARD CAMERA AS S'Y

SC REW

CONTROL PCB

DISK

PUSH BUTTON

CABLE

BASE

If the product is to be put out of operation definitively, take it to a local recycling plant for a disposal which is not harmful to the environment.

◐

SPECIFICATION

Model No.

Image Sensor

Effective Pixel

Cell Size

Resolution

TV Type

Sync. Type

Scanning System

Video Output

Gamma Characteristic

Min. Illumination

OSD

Motion Detection

Impact Detection(option)

White Balace

Privacy Zone

Day & Night

RS- 485 Protocol

S/N Ratio

Mirror

Backlight

Reverse polarity protection

Control Interface

Gain Control

Shutter

Test Illuminance Area

Power Supply

Current Consumption

Lens

LED

Operation Temp.

Preservation Temp.

Dimension

Weight

DOIRP3000F

1/3" SONY SUPER HAD CCD Ⅱ

768(H) X 494(V ) PIXEL(NTSC)

752(H) X 582(V) PIXEL(PAL)

6.35

㎛ (H) X 7.4

㎛ (V)(NTSC)

6.5

㎛ (H) X 6.25

㎛ (V)(PAL)

700 TV- Line

NTSC / PAL

Internal

2:1 Interlace

1.0 Vp- p(Sync. Negative) Termination 75Ω ± 10 %

γ = 0.45(Adjustable)

0 Lux(15M Range) : LED ON

0.1Lux(F/1.2) : LED OFF

Full OSD

ON / OFF Selectable(64 Zone)

ON / OFF Selectable(3 Step : LOW / MIDDLE / HIGH)

ATW / AWC / MANUAL

ON / OFF Selectable(4 Zone)

Electronic D&N(AUTO, COLOR, B/W)

PELC O- D&P

48dB over(AGC OFF)

ON / OFF

DWDR / BLC / HLC / OFF

YES

Extra Video connector for easy installation

Automatic(Adjustable)

1/60~ 1/100,000sec(NTSC), 1/50~ 1/100,000sec(PAL)

Average test illuminance by front view

Regulated 12V DC ± 10%

Max. 300mA(at 12V DC)

Fixed focal lens

IR LED 14EA

- 10 ∼ 50 ℃

- 20 ∼ 60 ℃

Ø 110 × 80(H)mm

Approx. 230g

◐

FUNCTION SETTING

1. OSD menu structure

Func tion setting menu S elect menu

LENS

Sub menu

MANUAL, DC

BRIGHT 0 ~ 100

1. EXPOSURE

DC LEVEL

E.SHUTTER

AGC

DWDR

BLC

HLC

HLC THR

0 ~ 20

AUTO

1/60(1/50) ~ 1/100,000

OFF, LOW,

MIDDLE, HIGH

OFF, LOW, MIDDLE, HIGH

OFF, ON

OFF, ON,

AUTO

0 ~ 100

Contents

Fixed focal lens or Vari- focal auto iris lens

In case of manual lens selection, adjust the brightness

In case of DC lens selection, adjust the brightness

Shutter speed auto adjustable

Select shutter speed manually

Determines that use the AGC function or not and AGC level selectable(You can not use the

Auto D&N change mode when AGC is off)

Digital Wide Dynamic Range

BLC function

High Light Mask function

In case of AUTO mode, the function will off in daytime and on at night

According to the threshold value, the camera will recognize as High light or not.

※ All specification is subject to change withoutnotic e to improve the quality.

2. WHITE

BALANCE

3. DAY&NIGHT

4. IMAGE

ADJUST

5. MOTION &

IMPACT

6. PRIVACY

MASK

7. COMMUNI-

CATION

8. SPECIAL

AWB MODE

D&N MODE

BURST

COLOR

→

→ B&W

B&W COLOR

DELAY TIME

LED LEVEL

DYNAMIC IR

MIRROR

SHARPNESS

GAMMA

LSC

ATW

MANUAL

AWC ↓

AUTO

COLOR

B&W

Color temperature 2500 ~ 9500°K

Adjust the Red or Blue values to shift the color of the object

Move the camera lens toward to white paper then press the set button to find the optimal white balance for current environment

Auto day&night switching mode

Fixed at color(LED OFF)

Fixed at B/W(LED ON)

OFF, ON

85 ~ 170

50 ~ 135

3 ~ 15

Determines whether to transmitthe burst signal or not in B/W mode

You can select brightness of illumination about changing the day ↔ night mode

You can selectthe duration time aboutchaining the day ↔ nightmode

IR LED OFF/ON and output level adjustable OFF, LOW, MIDDLE, HIGH

OFF, ON

OFF, ON

0 ~ 50

0.45, 0.6, 1, USER

OFF, ON

When IR LED is turned on in B/W, the objects can be clearly identified due to the function that decreases screen saturation of objects within a short distance.

Set a horizontal image inversion

Sharpness adjustable

Gamma adjustable

Determines whether to use the brightness compensation of four lens' corners(LSC) or not

0 ~ 50

0 ~ 200

0 ~ 200

The LSC level selectable

Adjust Red tone of the image

Adjust Blue tone of the image

Test signal. Press the set button, color bar appeared on the screen and press any key to return to menu(SK- D385IR/M843 only)

OFF, ON

LSC LEVEL

R- Y GAIN

B- Y GAIN

PATT ERN

GE NERATOR

MOTION

NONE

No display on the screen though movement is detected

DISPLAY

SET

WINDOW

ALL SET ↓

ALLCLE AR ↓

SENSITIVITY

HOLD TIME

IMPACT

HOLD TIME

MESSAGE

MASK

Motion detection area appear on the screen when movement is detected

Press the set button to move into the motion detection area section to setthe 64 areas. Press the set button for a few second to move out

Press the set button to select all area

Press the set button to remove all area

0 ~ 255

1 ~ 15

Motion detection sensitivity

Set the duration of outside alarm. If the way of display is message, it means display time of message

OFF, LOW,

MIDDLE, HIGH

1 ~ 15

Determines whether to use impact detection function or not and sensitivity setting

Set the duration of outside alarm and display time of "IMPACT" message

Display each privacy mask or not. Press the set button to move into the privacy mask

MASK

1, 2, 3, 4

OFF, ON button, the mask color is changed. When the mask color is red you can adjust the size by up, down, left and right button. When the mask color is blue you can set the position of mask by up, down, leftand right button. Press the setbutton for a few second to escape

Select mask color

Selectthe camera ID for RS- 485 communication

MASK COLOR

CAM ID

EDIT

BLACK, GRAY…

1 ~ 255

BAUDRATE

PROTOCOL

2400 ~ 9600

PELCO- D, PELCO- P

Select baud rate

Select protocol

※ If you change the COMMUNICATION value through RS- 485, you might not control the camera due to unmatched value(If your camera is out of working due to above reason, change your controller's value or wait a few minute till close the menu, it will be back to previous setting value)

LANGUAGE

NAME DISPLAY

ENGLISH, …

OFF, ON

Select language

Display the camera ID on the screen

Press the set button to move into the name setting section. You can choose the letter by using up and down button and move

9. FACTORY

SET

10. EXIT

POSITION

Press the set button to move into the position setting section.

You can move the camera ID to your wanted position by using up, down, left and right button

To reset your camera to factory default condition

Notice : Lens, communication and language is not changed

Save the value and then restart

2. How to use the jog lever

6

2

4 5

1

① ENTER :

3

ㆍ Push the lever : Used to access the menu and confirm selection.

ㆍ Push the lever for one second : Used to return to previous menu from the motion detection setting section or privacy mask setting section.

② UP, ③ DOWN

④ LEFT, ⑤ RIGHT

: Used to move the cursor to up or down.

: Used to move the cursor to leftor right and change

⑥ the value.

EXT- VIDEO : Extra video output terminal for installation.

Plug your test monitor in hear. The cable is option.

3. How to control through RS- 485 communication (option)

1) Mat ch the camera with controller's ID, baudrate and protocol

2) Up, Down, Left and right of Jog lever is same as Up, Down, Left and right of RS- 485 controller

3) Enter of Jog lever is the same as menu key or IRIS open key of

RS - 485 controller

4) Return to previous menu from motion detection setting section and privacy mask setting section : Iris close or Iris open for a few second.

Or press the button as Up Right Down Leftsuccessively

1) No impact & motion alarm type

E : ORANGE(RX +)

F : WHITE(RX - )

2) Built- in impact & motion alarm type

A : BLUE(MOTION)

B : BLACK(GND)

C : GREEN(IMPACT)

D : BLACK(GND)

E : ORANGE(RX +)

F : WHITE(RX - )

A

B

C

D

E

F

No.

FUNCTION

MOTION ALARM

GND

IMPACT ALARM

GND

RX +

RX -

REMARK

ㆍ If the camera detected motion when using Motion & Impact function, outside line of motion alarm connect with GND(B).

ㆍ If the camera detect impact, outsie line of impact alarm connect with GND(D).Outputs of Motion & Impact are 'open collector'.

ㆍ Max current & voltage are 200mA and 30V DC.

RS- 485A

RS- 485B