advertisement
!
GRAND NOBLE 7.5FT ONE STEP TREE - CLEAR - ITEM# 147677 CLE
GRAND NOBLE 7.5FT ONE STEP TREE - MULTI - ITEM# 147677 MUL
GRAND NOBLE 7.5FT ONE STEP TREE - CLEAR - ITEM# 147677 CLE
GRAND NOBLE 7.5FT ONE STEP TREE - MULTI - ITEM# 147677 MUL
PARTS LIST
A. BOTTOM
B. MIDDLE
C. TOP
NUMBER OF PERSONS
RECOMMENDED FOR
ASSEMBLY: 1
SKU 147677 CLE - GRAND NOBLE 7.5ft CLEAR
SKU 147677 MUL - GRAND NOBLE 7.5ft MULTI
4423 TIPS
UL 1200 REMAIN-ON LIGHTS
MAX DIAMETER 65”
HARDWARE
A. TREE BAG
B. ONE-STEP STAND AND PADDED COVER
C. QUICK LIGHT POLE
D. ACCESSORY BAG
SURGE PROTECTOR
REMOTE CONTROL W/RECEIVER
EXTRA BULBS AND FUSES
LIGHT STRING
QUANTITY: 1 SET
QUANTITY: 1 SET
QUANTITY: 1 SET
QUANTITY: 1 PC
QUANTITY: 1 SET
QUANTITY: EACH 20 PCS
QUANTITY: 2 PCS
ASSEMBLY INSTRUCTIONS
Step 1
Lay the carton down flat on the floor to open. Remove the bag containing the top sections, instruction sheet and accessory bag and put to the side until needed. PLEASE READ AND
FOLLOW THE ASSEMBLY INSTRUCTION CAREFULLY
WHEN SETTING UP THE ONE-STEP TREE
Step 2
To make it easier to remove your ONE-STEP TREE, it is recommended to close the carton flaps and reposition the tree carton flat on floor with arrows pointing upright. Please note, the tree is packed with storage bag, the one-step stand is attached to the tree and should never be removed
Step 3
Before moving your ONE-STEP TREE make sure you have created a safe display location for your tree by removing any items or furniture that may hit your tree during the inverting process. Using the green handle located near the top of the main tree storage bag, tilt the tree back and slowly wheel it to its final display location.
Step 4
Press down the locking tabs on both wheels once the tree is in its desired location
Step 5
Remove the main tree storage bag. Unbuckle both cinch straps located on the sides of the main bag and unbuckle at the base of the bag next to the stand. Then unfastening the Velcro and removing the main bag.
Unzip the tree top and remove the bag
Step 6
Your ONE-STEP TREE requires only one person to invert the tree into the display or storage position, others, especially small children that are assisting in the assembly of your ONE-STEP TREE should stand at a safe distance while inverting your tree
Step 7
With your foot on the footrest begin pulling the tree in the direction shown by the ONE-STEP TREE indicator
(towards you and down to the center of the foot pedal).
Step 8
Once you have completed inverting your tree, insert the Quick-Light pole from section B into Section A.
Turn Section B gently when inserting the pole to insure that the contact points of the Quick-Light pole move to the correct position. Repeat, by inserting the top section C into Section B. Once the tree is assembled, plug the light cord found at the base of
Section A into the surge protector (Sections B and C will be powered automatically through the Quick-
Light pole)
Step 9
Plug surge protector into the remote control receiver. Then plug remote receiver into wall outlet
!
Top Section C
ELECTRICAL
CONNECTION
Middle Section B
ELECTRICAL
CONNECTION
Drawing not to scale
Bottom Section A
STORAGE TIPS
Step1
Unplug the cord connecting the tree lights to the remote and wall socket.
Step2
Remove the tree top and middle section and place both in the tree storage bag. If you find it difficult to remove the tree top sections in this position, you may wish to unlock the safety lock (as below process) and tilt the tree slightly for easier access.
Step3
Unlock the safety lock on tree stand
1) Step firmly on the foot pedal until fully
depressed and in the locked position
2) The pole lock will then be released and you
will see the tree pole raise slightly
3) You will find the strap hidden under the branch
4) Holding the strap and pull it upward direction for
inverting the tree in storage position
Step 4
Place the main tree storage bag over the top of the tree making sure the velcro is aligned with the center of the foot rest
Step 5
Gently pull the bag down over the tree until the bag nearly touches the floor. Then fasten the bag.
Step 6
Fasten the two cinch straps on the both side of the main tree bag in cross position. Then, fasten strap at the base of the tree
Step 7
Unlock the wheels, grab the handle, tilt the tree back, and proceed to wheel the tree to its final storage location.
CARE & MAINTENANCE INSTRUCTION
1. This is for decorative use only - do not immerse in water or expose to heat. Keep away from fire.
2. Please use water only for cleaning purpose.
3. When not in use, store neatly in a cool, dry location protected from sun light
4. When the remote control has malfunctioned, please remove the surge protector from the receiver and plug the surge protector directly into the wall
THE FOLLOWING STEPS WILL HELP MAKE YOUR TREE LOOK MORE REALISTIC
1. Light tree one section at a time as described in assembly instructions, so you can easily identify and
bulbs that may be dislodged. Push any loose bulbs back into their sockets.
2. Separate the branch tips to form a “V” shape and fluff the needles. Make sure each tip is spread out
and no two branches are touching each other. For best access to branches, shape each section prior to
adding the next section as described in the initial assembly instructions. You may want to wear
cotton gloves when fluffing needles to avoid scratches and skin irritation.
3. Starting with the bottom row, position the branches parallel to the floor. Angle the tips slightly
upward like they are growing towards the sun. With each successive row, make the upward angle of
the branches more pronounced. Position inner tips to hide the center of the tree.
4. Arrange the uppermost section of the tree so that the tips are evenly spaced and pointing upward.
5. Step back and review the tree. Adjust branches and tips as necessary to give the tree a fuller
appearance (The tree may be shaped differently (upswept/downswept/ etc.) pending on one’s
preference.)
TROUBLE SHOOTING TIPS
1. If entire tree lighting does not light, make sure the light sets are securely inserted in a working wall outlet.
2. If an entire section of the tree does not light, please review following actions: a) Check that all plugs within the tree are securely connected.
b) Check the fuse in light sets to determine if it may need replacement. Caution: Noted that a
blown fuse indicates an electrical overload or electrical short circuit. If the fuse is blown,
unplug light sets from outlet. Also, unplug any additional strings. Replace the fuse following
manufacturer instruction with proper fuse rating. If the replacement fuse blows, a short circuit
may be present and the product should be discarded.
c) Check fuse in plug connection on end of each light string (See section on replacing plug fuses
in this document).
TROUBLE SHOOTING TIPS (Cont.)
3. If some individual lights do not light up, it may be due to becoming dislodged from the socket during
assembly. Note those not lit up; check for looseness and push any loose bulbs gently back into their
socket. If they still do not light up, try a replacement light bulb (supplied by manufacturer) and
follow directions in section describing how to replace light bulbs.
TROUBLE SHOOTING TIPS (Cont.)
When using electrical products, to avoid risk of fire burns, personal injury and electrical shock, basic precautions should always be followed as stated below:
RED AND FOLLOW ALL SAFETY INSTRUCTIONS
1. Do not use seasonal products outdoors unless marked suitable for indoor and outdoor use. When
products are used in outdoor applications, connect the product to a Ground Fault Circuit
interrupting (CFCI) outlet. If one is not provided, contact a qualified electrician for proper
installation.
2. This seasonal use product is not intended for permanent installation or use.
3 Do not mount or place near gas or electrical heaters, fireplace, candles or other similar sources of
heat.
4. Do not secure the wiring of the product with staples or nails, or place on sharp hooks or nails.
5. Do not let lamps rest on the supply cord or on any wire.
6. For your safety, unplug the product when leaving the house, when retiring for the night or if left
unattended.
7. This is an electrical product - not a toy! To avoid risk of fire, burns, personal injury and electric
shock it should not be played with or placed where small children can reach it.
8. Do not use this product for other than its intended use.
9. Do not hang ornaments or other objects from cord, wire or light string.
10. Do not close doors or windows on the product or extensions cords as this may damage the wire
insulation.
11. Do not cover the product with cloth, paper or any material not part of the product when in use.
12. This product is equipped wit push-in lamps. Do not twist the lamps.
13. This product employs overload protection (fuse). A blown fuse indicates an overload or
short-circuit situation. If the fuse blows, unplug the product from the outlet. Also, unplug any
additional strings or products that may be attached to the product. Replace the fuse as per the user
servicing instructions (follow product marking for proper fuse rating) and check the product. If
the replacement fuse blows a short-circuit may be present and the product should be discarded.
14. Read and follow all instructions that are on the product or provided with the product.
USER INSTRUCTIONS
TO
REPLACE LIGHT BULBS
CAUTION: FIRST UNPLUG YOUR PRODUCT FROM ANY POWER SOURCE.
1. To reduce the risk of overheating, replace burned-out light bulbs promptly. Use only
2.5 volt light bulbs only.
2. Grasp plug and remove from the receptacle or any other electrical outlet device. Do
not unplug by pulling on the cord.
3. Pull the light bulb and its attached plastic base straight out of light bulb holder
4. Replace light bulb with only 2.5 volt super bright type light (provided with product).
5. If the new lamp base does not fit the replacement light bulb, follow the steps below
before step 4
A. Remove the base of burned out light by straightening light leads and gently pull
bulb out.
B. Thread metal leads of new lamp through hose in old base with one lead in each
hold.
C. After lamp is fully inserted into base, bend each lead up, like other lights in the
light set so that the leads will touch the contacts inside the light socket.
PULL BULB UP
TO REMOVE
PUSH BULB DOWN
TO REPLACE
TO
REPLACE A FUSE
CAUTION: FIRST UNPLUG YOUR PRODUCT FROM ANY POWER SOURCE.
1. Grasp plug and remove from the receptacle or other outlet device. Do not unplug
by pulling on cord.
2. Open fuse cover. Slide open fuse access cover on top of attachment plug towards
plug’s metal prongs or blades
3. Remove fuse carefully (do not apply pressure to the glass part of fuse when
removing or replacing.)
4. Risk of fire. Replace fuse ONLY with 3 Amp 120 Volt fuse. (Provided with product).
5. Close fuse cover. Return the sliding fuse cover back to its former closed position on
attachment plug.
6. Risk of fire. Do not replace attachment plug because it contains a safety device (fuse)
that should not be removed. Discard product if the attachment plug is damaged.
OPEN
OPEN
FUSE OVER
SLIDES FORWARD
3 AMP
120 VOLT
FUSES
E305737
MODEL NO.: YXOULA 100L/2F
MODEL NO.: YXOULA 50L/1F
Please contact one of our Product Specialists for assembly assistance or questions at 1-800-537-8484 or email [email protected]
Specialists are available weekdays 8:00 a.m. to 8:00 p.m. EST or Saturday 9:30 a.m. to 6:00 p.m.
advertisement
Related manuals
advertisement