advertisement
TROUBLE SHOOTING TIPS (Cont.)
3. If some individual lights do not light up, it may be due to becoming dislodged from the socket during assembly. Note those not lit up; check for looseness and push any loose bulbs gently back into their socket. If they still do not light up, try a replacement light bulb (supplied by manufacturer) and follow directions in section describing how to replace light bulbs.
IMPORTANT BASIC SAFETY INSTRUCTIONS
When using electrical products, to avoid risk of fire burns, personal injury and electrical shock, basic precautions should always be followed as stated below:
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
1. Do not use seasonal products outdoors unless marked suitable for indoor and outdoor use. When products are used in outdoor applications, connect the product to a Ground Fault Circuit interrupting (GFCI) outlet. If one is not provided, contact a qualified electrician for proper installation.
2. This seasonal use product is not intended for permanent installation or use.
3. Do not mount or place near gas or electrical heaters, fireplace, candles or other similar sources of heat.
4. Do not secure the wiring of the product with staples or nails, or place on sharp hooks or nails.
5. Do not let lamps rest on the supply cord or on any wire.
6. For your safety, unplug the product when leaving the house, when retiring for the night or if left unattended.
7. This is an electrical product – not a toy! T o avoid risk of fire, burns, personal injury and electric shock it should not be played with or placed where small children can reach it.
8. Do not use this product for other than its intended use.
9.
Do not hang ornaments or other objects from cord, wire or light string.
10. Do not close doors or windows on the product or extensions cords as this may damage the wire insulation.
11. Do not cover the product with cloth, paper or any material not part of the product when in use.
12. This product is equipped with push-in lamps. Do not twist the lamps.
13. This product employs overload protection (fuse). A blown fuse indicates an overload or short-circuit situation. If the fuse blows, unplug the product from the outlet. Also unplug any additional strings or products that may be attached to the product. Replace the fuse as per the user servicing instructions (follow product marking for proper fuse rating) and check the product. If the replacement fuse blows, a short-circuit may be present and the product should be discarded.
14. Read and follow all instructions that are on the product or provided with the product.
CAUTION: T o reduce the risk of fire and electric shock: a. Do not install on trees having needles, leaves or branch coverings of metal or materials which look like metal, and: b. Do not mount or support strings in a manner that can cut or damage wire insulation.
USER INSTRUCTIONS
TO REPLACE LIGHT BULBS
CAUTION: FIRST UNPLUG YOUR PRODUCT FROM ANY POWER SOURCE.
1. To reduce the risk of overheating, replace burned-out light bulbs promptly. Use only
2.5 volt light bulbs only.
2. Grasp plug and remove from the receptacle or any other electrical outlet device. Do not unplug by pulling on the cord.
3. Pull the light bulb and its attached plastic base straight out of light bulb holder.
PULL BULB UP
TO REMOVE
PUSH BULB DOWN
TO REPLACE
4. Replace light bulb with only 2.5 volt super bright type light (provided with product).
5. If the new lamp base does not fit the replacement light bulb, follow the steps below before step 4.
a. Remove the base of burned out light by straightening light leads and gently pull bulb out.
b. Thread metal leads of new lamp through hose in old base with one lead in each hold.
c. After lamp is fully inserted into base, bend each lead up, like other lights in the light set so that the leads will touch the
contacts inside the light socket.
TO REPLACE A FUSE:
CAUTION: FIRST UNPLUG YOUR PRODUCT FROM ANY POWER SOURCE.
1. Grasp plug and remove from the receptacle or other outlet device. Do not unplug by pulling on cord.
2. Open fuse cover. Slide open fuse access cover on top of attachment plug towards plug’s metal prongs or blades.
3. Remove fuse carefully.
4. Risk of fire. Replace fuse ON LY with 3 Amp 120 Volt fuse. (Provided with product).
5. Close fuse cover. Return the sliding fuse cover back to its former closed position on attachment plug.
6. Risk of fire. Do not replace attachment plug because it contains a safety device (fuse) that should not be removed. Discard product if the attachment plug is damaged
OPEN
OPEN
FUSE COVER
SLIDES FORWARD
3 AMP
120 VOLT
FUSES
Please contact one of our Product Specialists for assembly assistance or questions at 1-800-537-8484 or email [email protected].
Specialists are available weekdays 8:00 a.m. to 8:00 p.m. EST or Saturday 9:30 a.m. to 6:00 p.m.
Big plug box instruction
The plug box tight on the tree.
Step 1
Open the plug box from the tree.
Step 2
Put out the cord from the plug box.
Then plug the light set from upper/lower section into the cord.
Step 3
Put back the cord into the plug box.
Then close the cover.
Small plug box Instruction
The plug box tight on the tree.
Plug light set from upper/lower section into the plug box.
STORAGE TIPS
Step 1
-
Step 2
Remove section (D) from (C) and gently press branches upward.
Step 3
Remove section (C) from (B) and hold upside down and branches will fold toward the pole. It is recommended to snuggly bind branches to the pole with a length of rope or twine, This will allow for easy handling and storage.
Step 4
Repeat step 3 for section (B).
Step 5
Untighten screws on stand and remove stand from section (A).
Repeat step 3.
Step 6
Place all tree sections, power strips, remote, and tree stand in original box and tape shut. Store tree in cool dry area, storage area temperature should not exceed 100ºF.
4 Parts
CARE & MAINTENANCE INSTRUCTION
1. This is for decorative use only - do not immerse in water or expose to heat. Keep away from fire.
2. Please use water only for cleaning purpose.
3. When not in use, store neatly in a cool, dry location protected from sun light.
4. When the remote control has malfunctioned, please remove the power strip from the receiver and plug the power strip directly into the wall.
THE FOLLOWING STEPS WILL HELP MAKE YOUR TREE LOOK MORE REALISTIC
1. Light tree one section at a time as described in assembly instructions, so you can easily identify any bulbs that may be dislodged.
Push any loose bulbs back into their sockets.
2. Separate the branch tips to form a “V” shape a nd flu ff the needles. Make sure each tip is spread out and no two branches are touching each other. For best access to branches, shape each section prior to adding the next section as described in the initial
assembly instructions. You may want to wear cotton gloves whe n fluffing n eedles to avoid scratches and skin irritation.
3. Starting with the bottom row , position the branches parallel to the floo r. Angle the tips slightly upward like they are growing towards the sun. With each successive row, make the upward angle of the branches more pronounced. Position inner tips to hide the center of the tree.
4. Arrange the uppermost section of the tree so that the tips are evenly spaced and pointing upward.
5. Step back and review the tree. Adjust branches and tips as neccessary to give the tree a fuller appearance (The tree may be shape differently (upswept /downswept /etc.) pending on one’s preference.)
TROUBLE SHOOTING TIPS
1. If entire tree lighting does not light, make sure power strip cords are securely inserted in a working wall outlet.
2. If an entire section of the tree does not light, please review following actions:
a. Check that all plugs within the tree are securely connected.
b. Check fuse in power strip to determine if it may need replacement. Caution: Note that a blown fuse indicates an electrical
overload or electrical short circuit. If the fuse is blown, unplug power strip from outlet. Also unplug any additional strings
or products may be attached to the power strip. Replace the fuse following manufacturer instructions with proper fuse
rating. If the replacement fuse blows, a short circuit may be present and the product should be discarded.
c. Check fuse in plug connection on end of each light string.(See section on replacing plug fuses in this document).
TROUBLE SHOOTING TIPS (Cont.)
3. If some individual lights do not light up, it may be due to becoming dislodged from the socket during assembly. Note those not lit up; check for looseness and push any loose bulbs gently back into their socket. If they still do not light up, try a replacement light bulb (supplied by manufacturer) and follow directions in section describing how to replace light bulbs.
IMPORTANT BASIC SAFETY INSTRUCTIONS
When using electrical products, to avoid risk of fire burns, personal injury and electrical shock, basic precautions should always be followed as stated below:
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
1. Do not use seasonal products outdoors unless marked suitable for indoor and outdoor use. When products are used in outdoor applications, connect the product to a Ground Fault Circuit interrupting (GFCI) outlet. If one is not provided, contact a qualified electrician for proper installation.
2. This seasonal use product is not intended for permanent installation or use.
3. Do not mount or place near gas or electrical heaters, fireplace, candles or other similar sources of heat.
4. Do not secure the wiring of the product with staples or nails, or place on sharp hooks or nails.
5. Do not let lamps rest on the supply cord or on any wire.
6. For your safety, unplug the product when leaving the house, when retiring for the night or if left unattended.
7. This is an electrical product – not a toy! T o avoid risk of fire, burns, personal injury and electric shock it should not be played with or placed where small children can reach it.
8. Do not use this product for other than its intended use.
9.
Do not hang ornaments or other objects from cord, wire or light string.
10. Do not close doors or windows on the product or extensions cords as this may damage the wire insulation.
11. Do not cover the product with cloth, paper or any material not part of the product when in use.
12. This product is equipped with push-in lamps. Do not twist the lamps.
13. This product employs overload protection (fuse). A blown fuse indicates an overload or short-circuit situation. If the fuse blows, unplug the product from the outlet. Also unplug any additional strings or products that may be attached to the product. Replace the fuse as per the user servicing instructions (follow product marking for proper fuse rating) and check the product. If the replacement fuse blows, a short-circuit may be present and the product should be discarded.
14. Read and follow all instructions that are on the product or provided with the product.
CAUTION: T o reduce the risk of fire and electric shock: a. Do not install on trees having needles, leaves or branch coverings of metal or materials which look like metal, and: b. Do not mount or support strings in a manner that can cut or damage wire insulation.
USER INSTRUCTIONS
TO REPLACE LIGHT BULBS
CAUTION: FIRST UNPLUG YOUR PRODUCT FROM ANY POWER SOURCE.
1. To reduce the risk of overheating, replace burned-out light bulbs promptly. Use only
2.5 volt light bulbs only.
2. Grasp plug and remove from the receptacle or any other electrical outlet device. Do not unplug by pulling on the cord.
3. Pull the light bulb and its attached plastic base straight out of light bulb holder.
PULL BULB UP
TO REMOVE
PUSH BULB DOWN
TO REPLACE
4. Replace light bulb with only 2.5 volt super bright type light (provided with product).
5. If the new lamp base does not fit the replacement light bulb, follow the steps below before step 4.
a. Remove the base of burned out light by straightening light leads and gently pull bulb out.
b. Thread metal leads of new lamp through hose in old base with one lead in each hold.
c. After lamp is fully inserted into base, bend each lead up, like other lights in the light set so that the leads will touch the
contacts inside the light socket.
TO REPLACE A FUSE:
CAUTION: FIRST UNPLUG YOUR PRODUCT FROM ANY POWER SOURCE.
1. Grasp plug and remove from the receptacle or other outlet device. Do not unplug by pulling on cord.
2. Open fuse cover. Slide open fuse access cover on top of attachment plug towards plug’s metal prongs or blades.
3. Remove fuse carefully.
4. Risk of fire. Replace fuse ON LY with 3 Amp 120 Volt fuse. (Provided with product).
5. Close fuse cover. Return the sliding fuse cover back to its former closed position on attachment plug.
6. Risk of fire. Do not replace attachment plug because it contains a safety device (fuse) that should not be removed. Discard product if the attachment plug is damaged
OPEN
OPEN
FUSE COVER
SLIDES FORWARD
3 AMP
120 VOLT
FUSES
Please contact one of our Product Specialists for assembly assistance or questions at 1-800-537-8484 or email [email protected].
Specialists are available weekdays 8:00 a.m. to 8:00 p.m. EST or Saturday 9:30 a.m. to 6:00 p.m.
Big plug box instruction
The plug box tight on the tree.
Step 1
Open the plug box from the tree.
Step 2
Put out the cord from the plug box.
Then plug the light set from upper/lower section into the cord.
Step 3
Put back the cord into the plug box.
Then close the cover.
Small plug box Instruction
The plug box tight on the tree.
Plug light set from upper/lower section into the plug box.
advertisement
Related manuals
advertisement