advertisement
User Manual
GF-1130-448 MH/L34
GF-2230-448 MH/L34
ANITA B s.r.o.
Průmyslová 2453/7
680 01 Boskovice
Czech republic tel: +420 516 454 774
+420 516 453 496 fax: +420 516 452 751 e-mail:
[email protected]
MP05300EN,MP05400EN_200120
VERSION DATE APPROVED BY
MP05300EN,MP05400EN_200120 20. 1. 2020 Ing. Kamil Krátký www.garudan.cz
All rights reserved. Property of Anita B s.r.o. and protected by copyright.
The use of this content without written consent of Anita B s.r.o. is prohibited.
Copyright © Anita B s.r.o. (2020)
© ANITA
MP05300EN,MP05400EN_200120 GF-1130-448,GF-2230-448 MH/L34 2
© ANITA
Content
MP05300EN,MP05400EN_200120 GF-1130-448,GF-2230-448 MH/L34 3
© ANITA
www.garudan.cz
MP05300EN,MP05400EN_200120 GF-1130-448,GF-2230-448 MH/L34 4
© ANITA
A BASIC INFORMATION
A1.
PRODUCT DESCRIPTION AND INTENDED USE
The machines are designated for use in the apparel, home textiles, accessories and footwear production. It is suitable for making a car seat covers, sofas, leather bags, tents, etc. Triple synchronous feed and special feeder provide smooth operation and even stitch even for heavy materials. Characteristic features of this machine are low level of noise and vibrations and large-capacity hook.
A2.
TECHNICAL SPECIFICATIONS
Model
Number of needles
Needle gauge
Use
Stitch type
Max. stitch length
Hand lever foot lift
Knee lever foot lift
Needle system
Needle size
Hook type
Lubrication
Motor
GF-1130-448 MH/L34 GF-2230-448 MH/L34
1 2
-
6.4 mm / 7.9 mm /
9.5 mm / 12.7 mm
Medium/Heavy materials
2-thread lockstitch max. 9 mm
9 mm
19 mm
135x17 for fabrics, 135x16 for leather
Nm. 110 -180 *
Vertical with ∅ 26 mm bobbin
Automatic with oil pump
Integrated servomotor 1x230V
68 kg Machine head weight 66 kg
Table weight
Working space
27 kg www.garudan.cz
Machine table dimensions 595 x 190 mm
Power
Ground plan dimensions (including frame)
Bedplate height
Machine height including thread stand
Noise level under standard conditions max. 850 W (for a short time during start-up)
1200 x 550 mm
740 – 800 mm
1550 mm
82 dB/A
Max. sewing speed 3000 st./min. **
* Machine is preset for needle Nm. 160
** Do not exceed specified sewing speed due to the service life of the machine mechanism.
This cannot be guaranteed under any conditions. It is necessary to reduce speed depending on the thread, needle and material, stitch length and the foot track.
MP05300EN,MP05400EN_200120 GF-1130-448,GF-2230-448 MH/L34 5
© ANITA
B SAFETY INSTRUCTIONS
Read the instructions carefully before installation and use. Keep this manual for future reference.
B1.
GENERAL INSTRUCTIONS
1.
Do not operate the sewing machine until proper preparation has been made by a technician or qualified person and safety precautions have been taken.
2.
Always follow the safety instructions when handling the machine.
3.
This sewing machine may only be operated by properly trained personnel.
4.
Maintenance, repair, inspection and adjustment of the machine may only be carried out by a qualified person.
5.
Work on electrical equipment may only be performed by a qualified worker or person with the appropriate authorization. Work on electric parts and equipment on your own is not permitted.
6.
The machine may only be used for its intended purpose.
7.
The warranty does not cover any problems in the operation of the machine that are caused by unauthorized modifications to the machine, as well as problems caused by non-observance of the instructions given in this manual and generally known habits for the operation and maintenance of industrial sewing machines.
B2.
INSTALLATION PRECAUTIONS
1.
Immediately report visible damage to the carrier. Check the contents of the order shipment and report any defects immediately to the manufacturer. Later claims will not be accepted.
2.
Use the machine after checking that it meets all the safety standards of your country.
3.
www.garudan.cz
and dust layer with a cloth or petrol before placing it on the work surface.
4.
The machine has been thoroughly inspected and tested before shipment. However, it may have been damaged by transport or impact. Check the operation of the machine with the handwheel, to detect extraordinary noises, heavy running, etc. before starting the test sewing.
5.
Never start the machine if the oil level is under or over the marked lines.
6.
Check that the power and phase are in accordance with the label instructions.
7.
Proper grounding of the machine is necessary.
8.
Use the correct grounding plug.
9.
Do not use an extension cord.
10.
Make sure that the power supply and voltage match the requirements on the label of the machine.
11.
Do not use the machine in explosive or corrosive environment.
12.
In the first two weeks, do not exceed 3/4 of the maximum machine speed.
13.
Check that the air pressure is between 0.55 and 0.6 MPa.
MP05300EN,MP05400EN_200120 GF-1130-448,GF-2230-448 MH/L34 6
© ANITA
B3.
OPERATIONAL SAFETY INSTRUCTIONS
1.
Do not use the machine without a belt cover, finger guards or other protective equipment.
2.
All protective equipment of the machine must be in place before operation. Do not use the machine without covers and protective equipment.
3.
Repair damaged covers or replace them immediately.
4.
If the safety label is damaged, order a new one from the machine supplier and place it in its original position.
5.
Switch off the machine and unplug it in these situations (the motor still rotates after turning off; wait until it stops completely):
when threading the needle (needles), hooks, etc.
when changing the needle, presser foot, needle plate, hooks, hook bobbins, feeders, needle guards, finger guards, work guides, etc.
when the machine is not in use and left unattended
when opening or removing the protective covers
for any maintenance, repair, inspection and adjustment of the machine
when cleaning the machine
6.
Wear safety goggles and gloves when lubricating the machine. Do not drink oil under any circumstances, as it may cause vomiting and diarrhoea. Keep oil out of the reach of children.
7.
Take special care when lifting / tilting the machine head. When tilting the machine head, make sure the machine is turned off. Always hold the machine head with both hands.
8.
When handling cords and plugs, check if the machine is switched off to avoid electrical shock and injury.
9.
Check the electrical cords for damage to avoid injury by touching an exposed wire.
10.
Do not place any objects on the power cord.
11.
Do not open or touch the inside of the junction box.
12.
It is strictly forbidden to connect any connector while the machine is powered. Risk of damage to electrical components and drives.
13.
Do not modify the machine in any way that could endanger safety.
14.
www.garudan.cz
15.
Do not wipe the machine with thinner or acetone.
16.
Use only original or approved spare parts from manufacturer.
17.
Ensure adequate illumination of the work area and the surroundings of the machine.
18.
Disconnect the compressed air supply before servicing and repairing pneumatic equipment. Drain off the residual compressed air before servicing.
B4.
WORKING SAFETY INSTRUCTIONS
1.
Make sure you know the position of Stop button before starting to work.
2.
Do not touch any moving parts or put objects into the machine while sewing.
3.
Be careful not to catch or place objects near the machine's moving mechanisms, particularly fingers, sleeves, clothing and hair.
4.
Never touch the needle when the machine is turned on and sewing.
5.
Never reach under the thread lever cover while the machine is on.
6.
Do not place your fingers in the needle guard holder when feeding material manually.
MP05300EN,MP05400EN_200120 GF-1130-448,GF-2230-448 MH/L34 7
© ANITA
7.
Do not work on the machine under the influence of alcohol or drugs.
8.
We recommend wearing safety goggles.
9.
Do not remove covers or any other safety device while the machine is running.
10.
Always turn off the main switch when leaving the machine.
B5.
DISPOSAL INSTRUCTIONS
For disposal of the machine contact your local dealer or manufacturer in accordance with legislation. www.garudan.cz
MP05300EN,MP05400EN_200120 GF-1130-448,GF-2230-448 MH/L34 8
© ANITA
C1.
OIL SUMP INSTALLATION
C MACHINE SETUP
Insert rubber cushions ① , ③, ④ into the bedplate and tighten the screws ② .
Installation of the oil sump:
According to the picture fasten the oil sump
(5) to the plate with eight screws. www.garudan.cz
MP05300EN,MP05400EN_200120 GF-1130-448,GF-2230-448 MH/L34 9
© ANITA
D OPERATING INSTRUCTIONS
D1.
REPLACING THE NEEDLE
Turn off the main power switch. Replace the needle only when the sewing machine is off.
For 1-needle machine GF-1130:
Turn the hand wheel to rise the needle bar 1 to the highest position.
Loosen the screw 2.
Pull out the needle from the needle bar 1 downwards.
Insert new needle into the opening in the needle bar 1 all the way up with the groove 3 to the right.
Tighten the screw 2.
For 2-needle machine GF-2230:
Turn the hand wheel (CCW) to rise the needle bar
1 to the highest position.
Loosen the screw 3.
Pull out the needle from the needle holder 2 downwards.
Insert new needle into the opening in the needle holder 2 all the way up with the groove of the www.garudan.cz
Tighten the screw 3.
When changing the needle size, you must adjust the distance of the hook to the needles, otherwise it will lead to malfunctioning:
Using the smaller size of the needle:
Skipping the stitches
Damaging the thread
Using the larger size of the needle:
Damaging of the tip of the hook
Damaging the needle
MP05300EN,MP05400EN_200120 GF-1130-448,GF-2230-448 MH/L34 10
© ANITA
D2.
THREADING THE MACHINE
D2.1.
Threding the bottom thread
1. Pull the latch up ①.
2. Hold the bobbin with the loose end of the thread in a CCW direction and put it into the hook.
3. Pass the thread through the opening ② and ③ and under the bottom thread tension spring.
MP05300EN,MP05400EN_200120 GF-1130-448,GF-2230-448 MH/L34 11
© ANITA
D2.2.
Winding the bobbin www.garudan.cz
1. Put the bobbin on the winding pin. Pass the thread through points ① to ③ and wind the end of the thread a few times around the bobbin.
2. Press the winder lever
Ⓐ
. Press the foot controller and machine will start winding. When the bobbin is full, winding stops automatically.
3. You can adjust the amount of thread by the metal plate screwed on to the winder lever A.
Loosen the screw and adjust position of the plate to stop winding at 80 % of the bobbin capacity.
4. It’s necessary to wind the thread evenly. Center the thread tension
Ⓒ
, adjust the position forward / backward and tighten the screw
Ⓓ
.
MP05300EN,MP05400EN_200120 GF-1130-448,GF-2230-448 MH/L34 12
© ANITA
D2.3.
Threading the upper thread
1. Thread the upper (needle) thread of GF-1130-448 MH as shown in the picture. www.garudan.cz
MP05300EN,MP05400EN_200120 GF-1130-448,GF-2230-448 MH/L34 13
2. Thread the upper (needle) threads of GF-2230-448 MH as shown in the picture.
© ANITA www.garudan.cz
MP05300EN,MP05400EN_200120 GF-1130-448,GF-2230-448 MH/L34 14
© ANITA
D3.
ADJUSTING THE STITCH LENGTH AND REVERSE STITCH
1. Press the locking plate ③ and set the desired stitch length by turning the dial ①.
2. Press the reverse lever ②, the ma chine will sew back. When the lever is released, the machine sews forward again.
D4.
THREAD TENSION ADJUSTMENT
D4.1.
Upper thread tension adjustment
Turn the thread tension nut ① clockwise to increase the tension. Turn the nut counterclockwise to decrease the tension. In double-needle machines, each thread has its own www.garudan.cz
D4.2.
Bottom thread tension adjustment
Turn the tension screw ② clockwise to increase the tension. Turn the screw counterclockwise to decrease the tension.
MP05300EN,MP05400EN_200120 GF-1130-448,GF-2230-448 MH/L34 15
© ANITA
D5.
PRESSER FOOT
D5.1.
Presser foot lift
1. Raise the presser foot lever ① up to a height of 9 mm.
2. Lowering the lift lever will lower the foot.
3. You can also lift the presser foot up to 19 mm using the knee lever or by pressing the pedal backwards. Pressing the pedal backwards requires a pressurized air supply.
D5.2.
Foot pressure adjustment
The nut ④ is used to lock the screw ③ . Loosen it before adjusting the pressure and tighten again www.garudan.cz
Turn the foot pressure screw ③ clockwise to increase the foot pressure. Turn it counterclockwise to decrease the pressure.
Similarly, use the screw ① and nut ② to finetune the foot pressure.
MP05300EN,MP05400EN_200120 GF-1130-448,GF-2230-448 MH/L34 16
© ANITA
D6.
HOOK SAFETY CLUTCH FUNCTION
During sewing, when the hook reaches beyond the limit, a safety lock is activated to lock it.
The needle will be still moving, but not the hook. Always remove the cause before running.
1. Press the button ① and turn the handwheel (CCW) until button ①clicks . Keep the button pressed and turn the handwheel backward (CW), until you hear a click.
2. Before running the machine motor in the usual way, check the proper functioning by turning the handwheel manually.
D7.
TIMING OF THE HOOK OPENER
www.garudan.cz
opener ① moves to the far right .
2. Push the hook ② in the direction of the arrow to bring it as close as possible to the hook opener ① until the nose ③ touches the groove on the needle plate ④.
3. Loosen the screw ⑤ and set the distance between the hook opener ① and the hook inner part Ⓐ to 0.1-0.3 mm.
MP05300EN,MP05400EN_200120 GF-1130-448,GF-2230-448 MH/L34 17
© ANITA
D8.
TIMING OF THE HOOK AND THE NEEDLE
Make the settings below with the stitch length set to 0.
1. Turn the handwheel and raise the needle bar
2.3 mm from the lowest position. Check if the needle ② and the tip of the hook ③ align with each other. If not, loosen the two screws
④ of the small gear and rotate the hook to bring its tip to the center of the needle. We call this position "the machine at the set point of
2.3 mm."
2. Adjust the height of the needle bar to the point when “the machine is at the set point of
2.3 mm”, the hook tip is about 0.5 mm above the upper edge of the needle eye. Loosen the needle bar screw ①and adjust the distance between the upper edge of the needle eye ② and the hook tip ③ to 0.5 mm. Tighten the screw.
www.garudan.cz
MP05300EN,MP05400EN_200120 GF-1130-448,GF-2230-448 MH/L34 18
© ANITA
3. To adjust the distance between the hook tip ③ and the needle ②, loosen the hook block screws ⑥ and the gear screws ⑤. Adjust the distance to 0.05-0.1 mm. Then tighten all screws.
4. Adjust the guard plate of the hook by bending it so that the distance between the plate ⑧ and the needle www.garudan.cz
The guard plate is intended to prevent contact of the needle with the hook tip, if the needle bends.
Adjust the distance when changing the needle size.
MP05300EN,MP05400EN_200120 GF-1130-448,GF-2230-448 MH/L34 19
© ANITA
D9.
CONTROL BUTTONS
Use the control buttons 1 to 6 to quickly switch on/off the desired function:
1. Reverse sewing
2. Cancelling the start/end back-tack
3. Presser foot pre-lift
4. Move the needle by ½ turn
5. Auxiliary tension
Button “C” can be programmed for one of the functions by holding down button “A” under the chosen button 1 to 6 until LED “B” flashes. You can manage chosen function by pushing the “C” button.
6. Pneumatic presser foot guide
D10.
TURNING THE LED LIGHT ON/OFF
Turn the lighting on/off using switch 1 on the side of the lighting. www.garudan.cz
MP05300EN,MP05400EN_200120 GF-1130-448,GF-2230-448 MH/L34 20
© ANITA
E MACHINE MAINTENANCE
.
E1.
LUBRICATING THE MACHINE
E1.1.
Lubricating the front part of the machine head
1. Loosen the front cover screws.
2. Remove the front cover.
3. Lubricate each day at the marked points.
4. Replace the cover.
5. Secure with screws.
E1.2.
Lubricating the machine head marked red. Add a few drops of oil to these points every day. If the machine oil could not use all the oil, decrease the frequency of the lubrication.
2. Before first use or after the long-term stop, lubricate the machine at marked points, remove cover ② and apply oil to each felt and hose.
3. "C" is the upper oil tank. Check the operation of the oil pump through the window.
MP05300EN,MP05400EN_200120 GF-1130-448,GF-2230-448 MH/L34 21
© ANITA
E1.3.
Refilling the oil sump
1. Place the oil filter head ② on the hose ③ and put it into the oil sump ① as shown. You can attach it using the magnet.
2Add the oil until the cap ② is completely submerged.
www.garudan.cz
3. If the oil level falls below 1/3 of the head height ②, add more oil.
MP05300EN,MP05400EN_200120 GF-1130-448,GF-2230-448 MH/L34 22
© ANITA
E2.
ADJUSTING THE LUBRICATION
E2.1.
Adjusting the lubrication of the hook
1. Loosen the nut ② and adjust the amount of lubrication with the screw ①. Turn the screw clockwise to decrease or counterclockwise to increase the amount of oil.
2. Test the proper amount of lubrication with a paper.
Place the paper close to the hook and bring the machine to maximum speed for a few seconds. You should see thin lines formed by the oil on the paper.
Too much oil Correct amount of oil Too little oil
E2.2.
Adjusting the lubrication of the upper oil tank www.garudan.cz
1. If too much oil accumulates in the upper oil tank, tilt the machine head and loosen the nut
① . T urn the screw ② counterclockwise. If the oil level is too low, turn the screw clockwise.
MP05300EN,MP05400EN_200120 GF-1130-448,GF-2230-448 MH/L34 23
© ANITA
F TROUBLESHOOTING
Problem
1. Broken thread
(2 - 3 mm left on the bottom side)
Cause
1. Damage int the path of thread, damaged tip of the needle or the hook.
2. Upper thread tension is too high.
3. The needle is touching the tip of the hook.
4. Insufficient oiling of the hook.
5. Upper thread tension is too low.
6. The thread lever spring is too strong, the range of movement is too small.
7. Incorrect timing of the needle and hook.
Solution
1. Sand the surface with sandpaper. Sand the hook with a file.
2. Reduce the upper thread tension.
3. Adjust the distance between the needle and the
4. Adjust the amount of
5. Increase the upper thread tension.
6. Reduce spring force, increase the range of motion.
7. Adjust needle and hook
1. Incorrect timing of the needle and hook.
1. Adjust needle and hook
2. Foot pressure too low. 2. Increase the foot pressure.
2. Skipping stitches 3. Incorrect distance
3. Adjust the distance (see between needle eye and the hook tip.
4. Incorrect needle type.
www.garudan.cz
1. Bobbin tension spring too 1. Lower the bottom thread tight. tension.
3. Thread too tight
2. Threads are threaded incorrectly.
3. Bobbin doesn’t move .
4. Bottom thread tension is too low.
2. Check the threading of upper and bottom thread.
3. Check the bobbin.
4. Increase the bottom thread tension.
5. Bottom thread too thick. 5. Use the thinner thread.
6. Damaged tip of the needle.
6. Change the needle.
MP05300EN,MP05400EN_200120 GF-1130-448,GF-2230-448 MH/L34 24
© ANITA
G DRIVE UNIT MANUAL
G1.
SAFETY INSTRUCTIONS
1) Read the manual carefully before installation and use.
2) Installation of the drive unit may only be carried out by a qualified person.
3) Follow all instructions indicated by symbols to avoid injury.
4) Do not use a multiple socket extension cord.
5) Make sure that the power supply and voltage match the requirements on the label of the machine.
6) Do not use in direct sunlight, outdoors and in the temperature over 45 °C or below 0 °C.
7) Do not use close to the heater. Humidity level must be between 30-95 %.
8) Do not use in dusty, corrosive or explosive environment.
9) Do not put heavy objects on the power cord, do not pull it or bend it.
10) Proper permanent grounding is necessary.
11) Use safety covers for all moving parts.
12) Do a test run at the slow speed and check the direction of the rotation.
13) Switch off the machine and unplug it in these situations:
• threading the needle (needles), hooks, etc.
• changing the needle, presser foot, needle plate, hooks, hook bobbins, feeders, needle guards, finger guards, work guides, etc.
• the machine is not in use and left unattended
• opening or removing the protective covers
• any maintenance, repair, inspection and adjustment of the machine
• cleaning the machine
14) Maintenance, repair, inspection and adjustment of the machine may only be carried out by a qualified person.
15) Use only original or approved spare parts from manufacturer.
16) Do not use heavy objects.
G2.
www.garudan.cz
The ASD58 series are power units that are designated to drive sewing machines and to be built into a sewing machine. They consist of the engine itself, the control box and the control panel (keypad). Other use is not permitted.
G3.
DRIVE UNIT TECHNICAL PARAMETERS
Product type
Voltage
Frequency
Max. power
ASD58-5 ASU58-55 ASD58-75 ASU58-75
AHE58-55
AC 23 0 ±20 % V
50/60 Hz
850 W
MP05300EN,MP05400EN_200120 GF-1130-448,GF-2230-448 MH/L34 25
G4.
INSTALLATION
G4.1.
Connector description www.garudan.cz
Control box of the AS series
MP05300EN,MP05400EN_200120 GF-1130-448,GF-2230-448 MH/L34
© ANITA
26
© ANITA
Connect the pedal and all connectors to the appropriate sockets as shown.
ATTENTION:
If you are unable to connect the connectors to the appropriate outlet, check the direction of the pins. Make sure you are plugging into the correct outlet.
G4.2.
Power supply and grounding
The grounding connection and checking of the correct connection parameters to the power supply may only be carried out by an electrician. The system ground - the yellow/green wire
- must be securely connected to electrical outlet to ensure safe operation and to prevent machine malfunctions.
ATTENTION: All wires must be connected separately to avoid overloading and safe operation of the machine!
G4.3.
Connecting and settings
For more information, consult the installation manual for your particular engine model.
Power unit control box installation www.garudan.cz
Make sure you have enough space on the right side of the plate to install the control box.
The control box is mounted on the right side under the plate.
To install the foot controller (pedal), make sure it is placed right under the power unit and attached to the underside of the plate. If necessary, loosen the screws, adjust the position and angle, and retighten.
MP05300EN,MP05400EN_200120 GF-1130-448,GF-2230-448 MH/L34 27
© ANITA
G5.
CONTROL PANEL
G5.1.
Control panel display
The drive unit can be used with different models of sewing machines, which can have different optional functions as thread cutting, programmable back-tacking, automatic foot lift, etc.
If your machine is not equipped with this option, some of the features described below will not be available for your model. They are shown on the display, but the machine will not perform them.
Control panel layout www.garudan.cz
Symbols of the LCD display
MP05300EN,MP05400EN_200120 GF-1130-448,GF-2230-448 MH/L34 28
© ANITA
Display icons description
No. Icon
1
2
3
4
5
6
7
8
9
Description
Automatic trimming
Slow start
No. Icon
10
11
Start back tacking 12
End back tacking
Sewing segment index
Numeric display
Foot lift after trimming
Foot lift after stopping
Needle down stop position
13
14
15
16
17
Description
Needle up stop position
Free sewing mode
W sewing mode
Segment sewing
Multi-segment mode
Auto test
Clamp function
Four-segment sewing www.garudan.cz
MP05300EN,MP05400EN_200120 GF-1130-448,GF-2230-448 MH/L34 29
© ANITA
7
8
9
10
G5.2.
Operation panel keys description
Button
1
2
3
4
5
Name
Function
(Parameters)
Description
Use the button to select and confirm parameter settings and return to the sewing mode.
Start back tacking Selects and turns on the initial back tacking.
End back tacking
Free sewing mode
W sewing mode key
Selects and turns on the end back tacking.
Selects free sewing mode. The icon lights up on the display. Press the foot control to start sewing.
Press this key to enter the W sewing mode. LCD
6 Multi-segment sewing icon is on. In W sewing interface use the corresponding key „+“ or „ „ to set number of stitches of each segment (A, B, D) default range 1~F corresponds to the value 1~15.
Press this key to enter the multi-segment sewing mode. LCD icon is on. In multi-segment sewing interface use „+“ or „ „ key to set max. 24 segments. P01 is number of segments, -01 is current segment setting, -16 is number of stitches in the segment.
Press this key to enter the four-segment sewing Four-segment sewing mode. LCD icon is on. In four-segment sewing www.garudan.cz
„ „ key to set number of stitches of each segment (E, F, G, H) default range 1~F corresponds to the value 1~15.
Slow start
When the icon is lit, the slow start mode is on.
Press the key again for turning the slow start mode off.
Thread clamp
When the icon is lit, the thread clamp mode is on. Press the key again for turning the thread clamp mode off.
Set the stop position of the needle. When the icon Needle up/down stop position is lit, the needle stops up. When the icon lit, the needle stops down in the fabric. Note: you
, is can select needle stop position directly as parameter
MP05300EN,MP05400EN_200120 GF-1130-448,GF-2230-448 MH/L34 30
© ANITA
13
14
11
12
15
16
17
18
H-43. Press +
Press for half stitch compensation. Press and hold for one stitch compensation. Hold for continuous compensational sewing. to enter the parameter.
Stitch compensation
Trimming
Foot lift mode
One-step multi segment sewing
Lighting
When the icon is lit, auto trimming function is on. Press again for turning the function off.
Select the presser foot stop position up or down.
Pressing the key repeatedly you change foot position sewing mode.
When the icon is lit, pressing the foot control the machine performs whole preprogrammed sewing in one step.
Turning the light on/off.
Custom functions You can preset any custom function for this key.
Speed Increase or decrease the sewing speed or adjust the value.
Increase/decrease Increase or decrease parameter values. www.garudan.cz
MP05300EN,MP05400EN_200120 GF-1130-448,GF-2230-448 MH/L34 31
Katalog náhradních dílů
Spare Parts List
GF-1130-448 MH/L34
ANITA B s.r.o.
Průmyslová 2453/7
680 01 Boskovice
Czech Republic tel: +420 516 454 774
+420 516 453 496 fax: +420 516 452 751 e-mail:
[email protected]
MP05300_200120
© ANITA
VERSION CREATED ON APPROVED BY
MP05300_200120 20. 1. 2020 Ing. Kamil Krátký www.garudan.cz
All rights reserved.
Property of Anita B s.r.o. and protected by copyright. The use of this content without written consent of Anita B s.r.o. is prohibited.
Copyright © Anita B s .r.o. (2020)
MP05300_200120 GF-1130-448 MH/L34 2
© ANITA
Content
www.garudan.cz
MP05300_200120 GF-1130-448 MH/L34 3
A. FRAME & MISCELLANEOUS COVER
© ANITA www.garudan.cz
MP05300_200120 GF-1130-448 MH/L34 4
© ANITA
Ref. No
32
33
34
35
28
29
30
31
36
37
22
23
25
26
18
19
20
21
14
15
16
17
7
10
11
12
5
6
3
4
1
2
Part No.
A. FRAME & MISCELLANEOUS COVER
Part Name
40016798
FACE PLATE ASM.
SS4111215SP
SCREW 11/64-40 L=12
TA1250406RO
LUBRICATION SUPPLEMENT
21331301
TOP COVER B
SS4110815SP
SCREW 11/64-40 L=8
020182
THREAD GUIDE PLATE
SS05090610SP
SCREW 9/64-40 L=9
020181
21331202
SS6091022TP
RUBBER PLUG
SETSCREW
SCREW
TA1050504RO
TA1050504RO
21349600
21332200
21331608
SS7150910TP
22619100A
10201200A
020186
21349808
22602601
21361407
RUBBER PLUG
RUBBER PLUG
BED SLIDE(LEFT) A
OIL BAFFLE PLATE
BALANCE COVER
SCREW 15/64-28 L=9
CAP
RUBBER PLUG
LIGHTING ASM.
BED SLIDE(RIGHT) A
BED SCREW STUD
BED SUPPORT PLATE
17912106
B1132521000
NEEDLE THREAD PRESSER PLATE
THREAD PRESSER PLATE SPRING
22651202 AUXILIARY COVER
SS2090710TP
SS6151210SP
SCREW 9/64-40 L=7.2 www.garudan.cz
SD0380551SL HINGE SCREW D= 3.80 H= 5.5
B1111563000
SS4110515SP
BED SLIDE SPRING
SCREW 11/64-40 L=5
B1109562D00A
SS2110920TP
NEEDLE PLATE
SCREW 11/64-40 L=8.5
Qty
1
2
2
1
1
2
1
2
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
2
4
2
1
3
2
1
12
1
MP05300_200120 GF-1130-448 MH/L34 5
B. TAKE-UP AND UPPER SHAFT COMPONENTS
© ANITA www.garudan.cz
MP05300_200120 GF-1130-448 MH/L34 6
© ANITA
Ref. No
43
45
46
47
48
50
51
37
38
39
40
41
42
30
31
32
33
34
35
36
23
24
25
26
27
28
29
52
53
54
55
56
57
58
15
16
17
18
19
20
21
9
10
11
12
13
14
1
2
3
4
5
6
7
8
B. TAKE UP AND UPPER SHAFT COMPONENTS
Part No. Part Name
010243
21333000
010240
010235
B1906051000B
010241
010242
010247
SS8150822TP
SS8150710TP
SS8150710TP
010239
010245
SM8080812TP
21339502
SS8660810TP
21333109
CQ202000000
21336557
21336508
SS8660810TP
22604904
SS6661110SP
22604300
SS8150822TP
010262
010263
SS4110815SP
UPPER SHAFT
UPPER SHAFT FRONT METAL
CRANK SHAFT
TAKE-UP LEVER
TAKE-UP LEVER PIN
CURVED CONNETING ROD
PIN CRANK
SCREW
SCREW 15/64-28 L=8
SCREW 15/64-28 L=7
SCREW 15/64-28 L=7
COUNTER WEIGHT (A) (40MM)
FLYWHEEL
SCREW M8X8
UPPER FEED CAM (3.5)
SCREW 1/4-40 L=8
UPPER SHAFT INNER METAL
OIL WICK
ECCENTRIC CAM A ASM.
ECCENTRIC CAM A
SCREW 1/4-40 L=8
UPPER SPROCKET
SCREW 1/4-40 L=11
TIMING BELT
SCREW
BEARING A
BEARING B
SCREW 11/64-40 L=8
010258
21387501
B1214019000
010254
SS4110815SP
SCREW
LOWER SPROCKET
SPROCKET RING
BEARING A
SCREW 11/64-40 L=8
010256
40016148
010255
MOTOR PLATE
THRUST COLLAR B WASHER www.garudan.cz
MDBMASD58A850A
LS5A16
MOTOR
SCREW
010153
010426
21333901
MOTOR COVER
SCREW
SAFETY CLUTCH DISC
HX00123000A
21333802
RE0500000K0
B1639051000
B1313055000
SS8660530TP
40038700
40038702
SS8661030SP
SB120000200
SS7120760SP
21353008
SS7110710SP
TA0750704R0
CABLE CLIP
SAFETY CLUTCH PUSH BUTTON
E-RING
SPRING
SAFETY CLUTCH KNOB SLEEVE
SCREW 1/4-40 L= 4.5
THRUST COLLAR ASM.
THRUST COLLAR
SCREW 1/4-40 L=10
BEARING 20X42
SCREW 3/16-28 L= 7.0
HORIZONTAL FEED CAM COVER
SCREW 11/64-40 L=7
RUBBER PLUG
MP05300_200120 GF-1130-448 MH/L34
Qty
1
2
1
1
1
1
1
1
1
4
1
3
1
4
1
1
4
1
1
1
1
1
1
1
2
1
2
(1)
(2)
1
2
1
2
1
1
2
1
0.15
1
1
2
1
3
1
1
1
2
1
1
1
1
1
1
1
1
7
C. NEEDLE BAR ROCKING
© ANITA www.garudan.cz
MP05300_200120 GF-1130-448 MH/L34 8
© ANITA
Ref. No
27
28
29
30
23
24
25
26
31
32
19
20
21
22
15
16
17
18
11
12
13
14
7
8
9
10
5
6
3
4
1
2
Part No.
23002009
21405204
22814909
B1437051000
SS8151150TP
22814909
030338
B1411057000
SS7090910SP
CQ202000000
10308609
SS7080510TP
MC372001600
41438007
SS7110910TP
21388400
SS7110830SP
21338603A
SS6091022TP
21338801
SM8080812TP
21338900
C. NEEDLE BAR ROCKING
Part Name
NEEDLE BAR FRAME
HINGE STUD
FELT
OIL WICK RETAINER
SCREW 15/64-28 L=10.5
FELT
NEEDLE BAR
NEEDLE ROD HOLDER
SCREW 9/64-40 L= 8.5
OIL WICK
THREAD GUARD
SCREW 1/8-44 L=4.5
NEEDLE SY3355 160
UPPER FEED BAR GUIDE
SCREW 11/64-40 L= 8.5
ROCKING BASE GUIDE
SCREW 11/64-40 L= 7.5
ROCKING BASE GUIDE (B)
SCREW
ROCKING FRONT ARM
SCREW
ROCKING SHAFT
B1414232000
B1410771000
SQUARE BLOCK
STUD
21339304 ROCKING SHAFT FRONT METAL
40027746
21339056
BUSHING REAR www.garudan.cz
21339007 ROCKING REAR ARM
SS6152440SP
21347406
SCREW 15/64-28 L=23.5
ROCKING REAR ARM FELT
EA9500B0000
CQ202000000
CABLE BAND
OIL WICK
Qty
-1
1
1
1
1
1
1
1
2
0.05
2
1
2
1
2
1
2
1
1
1
1
1
1
1
1
0.04
1
1
1
1
1
1
MP05300_200120 GF-1130-448 MH/L34 9
D. PRESSURE ADJUSTING & UPPER FEED MECHANISM (1/2)
© ANITA www.garudan.cz
MP05300_200120 GF-1130-448 MH/L34 10
© ANITA
Ref. No
19
20
21
22
15
16
17
18
10
11
12
13
14
3
4
5
1
2
8
9
6
7
27
28
29
30
31
23
24
25
26
43
44
45
46
39
40
41
42
47
48
49
50
32
33
34
35
36
37
38
21340401
21340500
SS8660612TP
21341904
21378302
22904155
22904106
SS8660610TP
SS8150822TP
TA0750704RO
40033027
40033026
21347109
EA9500B0000
SM6040552TP
SD0640701SP
B1414555000
WP0501046SC
40033029
SS7110510SP
CQ202000000
10509701
0145653000L
40033030
B14670530A0
B1468053000
SS6151780SP
21406509
26225201
D. PRESSURE ADJUSTING & UPPER FEED MECHANISM (1/2)
Part No. Part Name
UPPER FEED SHAFT
UPPER FEED FRONT ARM
SCREW 1/4-40 L=6
FRONT METAL
FEED SHAFT METAL
MAIN SHAFT THRUST COLLAR ASM.
MAIN SHAFT THRUST COLLAR
SCREW 1/4-40 L=6
SCREW 15/64-28 L=7
RUBBER PLUG
UPPER FEED LINK ASM.
UPPER FEED LINK
FELT
CLIP CV-70S
SCREW M4 L=4.5
SCREW
SLIDE BLOCK
WASHER 5 X 13 X 1
TRIANGULAR LEVER ASM.
SCREW 11/64-40 L=5
OIL WICK
FELT
WALKING BAR DRIVING LINK
WALKING BAR A
WALKING BAR ASM.
WALKING BAR SPRING
SCREW 15/64-28 L=17.0
UPPER FEED GUIDE PLATE
ROLLER
SS6151920SP SCREW 15/64-28 L=19.0
21340302
SS7150740SP
21006408
UPPER FEED REAR ARM (B)
SCREW 15/64-28 L=7 www.garudan.cz
B1510155000 PRESSER BAR LOWER BUSHING
21339700
40017266
SS4110815SP
40018340
B1501241H00
40039265
40039266
SS7110910TP
22907604
B1502246000
SD0800481SP
SM6052002TP
B1462053000
21406103
21406608
21337803
UPPER FEED STOPPER PLATE
PRESSER FOOT ASM.
SCREW 1/4-40 L=8
SCREW
PRESSER BAR
PRESSER BAR HOLDER A ASM.
PRESSER BAR HOLDER A
SCREW 11/64-40 L= 8.5
PRESSER SPRING REGULATOR NUT
PRESSER SPRING
HINGE SCREW D= 8 H= 4.9
SCREW M5 L=20
THREAD RELEASE SPRING
PRESSER LIFTER LEVER
GUIDE PLATE SPACER
FEED ADJUSTING BASE SUPPORT
MP05300_200120 GF-1130-448 MH/L34
Qty
1
1
0.02
1
-1
1
2
1
1
1
-1
-1
-2
2
1
1
1
1
1
-1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
11
D. PRESSURE ADJUSTING & UPPER FEED MECHANISM (2/2)
© ANITA www.garudan.cz
MP05300_200120 GF-1130-448 MH/L34 12
© ANITA
Ref. No
77
78
79
80
73
74
75
76
69
70
71
72
65
66
67
68
85
86
87
88
81
82
83
84
89
90
61
62
63
64
57
58
59
60
51
52
53
54
55
56
D. PRESSURE ADJUSTING & UPPER FEED MECHANISM (2/2)
Part No. Part Name
21006002
21444559
21006507
NS6110530SP
40072709
SM8050602TP
10774354
SS8150710SP
SM6040802TP
10715100
10715001
10715704
B152652700G
SS6110630TP
21341607
10715308
SM6051402TP
21341508
10718203A
10714202
21438106
SM1050801SR
ADJUST SPRING B
WALKING FOOT ASM.
ADJUST SCREW B
NUT 11/64-40
SPRING SUPPORT SHAFT ASM.
SCREW M5 L=6
UPPER AND LOWER DIAL ASM.
SCREW 15/64-28 L=7
SCREW M4X0.7 L=8
VERTICAL DIAL SHAFT BUSHING
VERTICAL ADJUSTING CAM
VERTICAL DIAL PIN
SPRING
SCREW 11/64-40 L=6
VERTICAL ADJUSTING ARM
PIN
SCREW M5X0.8 L=14
VERTICAL CHANGE BASE SHAFT
FEED SHAFT FRONT METAL
VERTICAL CHANGE BELT
STOPPER PLATE B
SCREW M5 L=8
NS6680320SP
SS4110815SP
NUT 9/32-28
SCREW
10713501 SPRING HOOK
10716504
B3416552000
VERTICAL SHAFT SPRING www.garudan.cz
RE0500000K0 E-RING
21339809
SS7110830SP
UPPER FEED DOG SPRING HOOK
SCREW 11/64-40 L= 7.5
10713766
SS8660810TP
10713808
10714509
10714608
SM8050602TP
21340005
21048707A
RE0800000K0
SS4110815SP
ECCENTRIC ROD (SET)
SCREW 1/4-40 L=8
CONNECTION LINK PIN B
CONNECTION LINK B
CONNECTION LINK B SUPPORT PIN
SCREW M5 L=6
UPPER FEED LINK (B)
HINGE SCREW
E-SHAPED SNAP RING (8MM)
SCREW 11/64-40 L=8
Qty
1
1
1
1
1
1
1
1
1
1
1
1
1
-1
1
3
1
1
1
1
2
（ 1 ）
1
1
2
2
1
1
1
2
1
2
1
1
2
2
2
1
1
2
MP05300_200120 GF-1130-448 MH/L34 13
E. FEED MECHANISM (1/2)
© ANITA www.garudan.cz
MP05300_200120 GF-1130-448 MH/L34 14
© ANITA
Ref. No
19
20
21
22
15
16
17
18
10
11
12
13
14
3
4
5
1
2
8
9
6
7
27
28
29
30
31
23
24
25
26
43
44
45
46
39
40
41
42
47
48
49
50
32
33
34
35
36
37
38
21337605
21338009
SS7111410TP
21337209
B1610512000
SM6061802TP
21336805A
010562
SS6121860SP
11009909
RO092270200
010563
22912109
21336656
21336607
B1418761OOO
Part No.
SS7150910TP
21430400
010561
SS9151440CP
WP0621016SD
SM8050502TP
B1604012000A
RE0500711KP
CQ202000000
21364104
SS7111410SP
020573
21378302
020514
22609309L
SS6121610TP
22904155
22904106
SS8660610TP
020574
SS6110630TP
21378203
21337506
21337704
SS7110910TP
21337407
21337803
SS8150822TP
21338306
E. FEED MECHANISM (1/2)
Part Name
SCREW 15/64-28 L=9
FEED ADJUSTING BASE SUPPORT
BOTTON
SCREW 15/64-28 L=14
WASHER 6.2X13X1
SCREW M5 L=5
FEED BAR SHAFT
SNAP RING 5
OIL WICK
FEED ROCKER
SCREW 11/64-40 L=14
FEED ROCK SHAFT
FEED SHAFT METAL
SCREW 11/64-40 L=8.5
FEED ROCKER SHAFT CRANK
SCREW 3/16-28 L=15.5
MAIN SHAFT THRUST COLLAR ASM.
MAIN SHAFT THRUST COLLAR
SCREW 1/4-40 L=6
NEEDLE BAR FRAME ROD
SCREW 11/64-40 L=6
FEED ROCK SHAFT HINGE SCREW
FEED ADJUSTING BASE
FEED ADJUSTING BASE COVER
SCREW 11/64-40 L= 8.5
SQUARE BLOCK
FEED ADJUSTING BASE SUPPORT
SCREW 15/64-28 L=8
FELT SUPPORT
SS5090610SP SCREW 9/64-40 L=6
21337902
SS709010TP
21337308
ECCENTRIC PIN
SCREW 9/64-40 L= 8.5 www.garudan.cz
SD0800402TP HINGE SCREW D= 8 H= 4
SPRING
SPRING HOOK
SCREW 11/64-40 L=16
FEED ADJUSTING A
FEED DRIVING SLIDE BLOCK
SCREW M6 L=18
FEED DIAL A
SPRING
SCREW 3/16-28 L=18
FEED REGULATOR SCREW
RUBBER RING
FEED REGULATOR PIN
FEED REGULATOR PIN SPRING
FEED LINK ASM.
FEED LINK
CONNECTING FORKED LINK PIN
MP05300_200120 GF-1130-448 MH/L34
Qty
1
1
1
1
1
1
1
1
1
1
（ 1 ）
1
1
1
2
1
1
2
1
4
2
1
2
1
1
1
1
2
1
2
2
2
1
1
2
1
1
2
（ 1 ）
（ 2 ）
1
1
1
（ 1 ）
（ 1 ）
（ 1 ）
1
1
0.14
1
15
E. FEED MECHANISM (2/2)
© ANITA www.garudan.cz
MP05300_200120 GF-1130-448 MH/L34 16
© ANITA
Ref. No
61
62
63
64
57
58
59
60
51
52
53
54
55
56
69
70
71
72
65
66
67
68
73
Part No.
CQ202000000
SM8050502TP
21336706
21338207
SD1000801SH
21336300
SS6580752TP
CS1201010SH
CS1201011SH
SS8660610TP
RE0900000K0
21388004
SS6120930TP
22814909
WP0621016SH
010932
21364252
020568
21336003
10107902
B1613563E00D
SD0900701TP
NS6680320SP
E. FEED MECHANISM (2/2)
Part Name
OIL WICK
SCREW M5X6
FEED ROD A
FEED LINK PIN
HINGE SCREW D=10 H=8
BACKWARD FEED LEVER SHAFT
SCREW 1/8-40 L=7
THRUST COLLAR ASM. D=12 W=10
THRUST COLLAR D=12 W=10
SS8660610TP SCREW 1/4-40 L=6
E-RING 9
REVERSE FEED CONTROL LEVER
SCREW 3/16-28 L=9
FELT
WASHER
NUT 1/4-40
FEED BASE ASM.
FEED SHAFT METAL
FEED BASE
FEED BAR FORK
FEED
SCREW
NUT 9/32 -28 www.garudan.cz
Qty
1
1
1
1
2
1
1
1
0.04
1
1
1
1
1
2
1
（ 1 ）
（ 2 ）
1
1
1
1
1
MP05300_200120 GF-1130-448 MH/L34 17
F. HOOK SHAFT & UPPER FEED MECHANISM
© ANITA www.garudan.cz
MP05300_200120 GF-1130-448 MH/L34 18
© ANITA
Ref. No
48
49
50
51
52
53
41
42
43
44
45
46
47
35
36
37
38
39
40
28
29
30
31
32
34
24
25
26
27
19
20
21
22
12
13
14
15
16
18
1
2
7
8
4
5
9
10
F. HOOK SHAFT & UPPER FEED MECHANISM
Part No. Part Name
21390000 HOOK SHAFT BASE (RIGHT)
B1802563OOOA BUSHING ASM. FRONT
10112506 THRUST WASHER 0.7
21334909 INNER HOOK GUIDE LINK
B1821051000 CRANK SCREW STUD
CQ202000000 OIL WICK
NS6110420SP
21335500
NUT 11/64-40
GUIDE ARM (FOR THREAD CUTTING)
SS8110422TP
B1823051000
SS7111810TP
CQ202000000
21335807
WP0371016SD
SS6090810SP
10111102
10112704
21378401
21334701
10109908
10112407
SS6153040SP
WP0850002SP
SM6082502TP
B1834512000A
NS6110420SP
SC1510NI1
21334800
SCREW 11/64-40 L=4
OPENING LEVER CRANK PIN
SCREW 11/64-40 L=18
OIL WICK
INNER HOOK GUIDE
WASHER 3.7X8X1
SCREW 9/64-40 L= 7.5
THRUST WASHER 0.9
THRUST WASHER 1.2
HOOK SHAFT UPPER METAL
HOOK SHAFT LOWER METAL
SADDLE INSTALLING BLOCK UPPER
SADDLE INSTALLING BLOCK LOWER
SCREW 15/64-28 L=30
WASHER 8.5X18X1.6
SCREW M8 L=25
OIL ADJUSTING SCREW
NUT 11/64-40
THREAD TRIMMER HOOK ASM.
ALUMINUM BOBBIN WITH KNURL
22611701 PLUNGER BUSHING B
020666
10111003
LOWER SHAFT www.garudan.cz
SS8151150TP SCREW 15/64-28 L=10.5
B18035150A0
SS8151150TP
BUSHING ASM. INTERMEDIATE
SCREW 15/64-28 L=10.5
10109700
22609804
SS8110422TP
SS8660530TP
B1817051000
SS8660670SP
SS8660530TP
B1816051000
SS8660810TP
SS8151150SP
SQ1110401MZ
22611909
SS8660530TP
THRUST WASHER 1.5
FEED DRIVING CAM
SCREW 11/64-40 L=4
SCREW 1/4-40 L= 4.5
HOOK DRIVING SHAFT GEAR SMALL
SCREW 1/4-40 L= 6.1
SCREW 1/4-40 L= 4.5
HOOK DRIVING SHAFT GEAR LARGE
SCREW 1/4-40 L=8
SCREW 15/64-28 L=10.5
CONNECTING SCREW
OIL PUMP SHAFT
SCREW 1/4-40 L= 4.5
MP05300_200120 GF-1130-448 MH/L34
Qty
1
1
（ 1 ）
1
1
1
1
1
2
1
1
0.02
1
1
1
1
1
1
1
0.02
1
1
1
2
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
19
G. THREAD CUTTING COMPONENTS
© ANITA www.garudan.cz
MP05300_200120 GF-1130-448 MH/L34 20
© ANITA
Ref. No
19
20
21
22
15
16
17
18
10
11
12
13
14
3
4
5
1
2
8
9
6
7
27
28
29
30
31
23
24
25
26
43
44
45
46
39
40
41
42
47
48
49
50
32
33
34
35
36
37
38
SS8110510SP
SS6151812TP
21354105
21354204
SD0640325SP
SS7111120SP
21390208
K034610160
WP0621016SD
THQ6
21389705
SS6121610TP
SD0640482SP
SS6121610TP
SD0640451TP
SS8660612TP
Part No.
21389200
SM6030802TP
PD3
21389556
21389507
21389309
21389408
SS7060610SP
21389911
21355102
21354600
SS6151040SP
SM6040802TP
21354709
SS6110710TP
SM6041202TP
WP0430800SC
21354907
CS0790731SH
SS8110422TP
21354501
SS7111120SP
21353750
21353701
SS8110510SP
21354006
10116804
21353859
21353909
G. THREAD CUTTING COMPONENTS
Part Name
MOVING KNIFE
SCREW M3X0.5 L=8
WASHER M3
FIXED KNIFE BASE (RIGHT) ASM.
FIXED KNIFE BASE (RIGHT)
FIXED KNIFE
CLAMP SPRING
SCREW 3/32-56 L= 5.5
THREAD TRIMMER CAM
THREAD CUTTING SOLENOID
SOLENOID FITTING PLATE
SCREW 15/64-28 L=10
SCREW M4X0.7 L=8
SOLENOID CONNECTING PLATE
SCREW 11/64-40 L= 6.5
SCREW M4X0.7 L=12
WASHER M4
MOVING KNIFE SHAFT
THRUST COLLAR
SCREW 11/64-40 L=4
THREAD CUTTING STOPPER (RIGHT)
SCREW 11/64-40 L=10.5
VERTICAL FITTING BASIS ASM.
VERTICAL FITTING BASIS
SCREW 11/64-40 L=5
THREAD CUTTING DRIVING PLATE
SHAFT
THREAD CUTTING ROLLER ARM
CAM ROLLER SHAFT
D2430555B00 SNAP RING
21353800
D2427555B00B
CS070081BSH
THREAD CUTTING ROLLER ARM
CAM ROLLER www.garudan.cz
CS0700811SH THRUST COLLAR D=7 W=8
SCREW 11/64-40 L=5
SCREW 15/64-28 L=18
CONNECTING PLATE
STOPPING PLATE
HINGE SCREW
SCREW 11/64-40 L=11
MAINTENANCE SPRING
HOUSING 12P
WASHER 6.2X13X1
SPRING WASHER
ROCKING ARM (RIGHT)
SCREW 3/16-28 L=15.5
HINGE SCREW D= 6.35 H= 4.8
SCREW 3/16-28 L=15.5
HINGE SCREW D=6.35 H=4.5
SCREW 1/4-40 L=6
MP05300_200120 GF-1130-448 MH/L34
Qty
1
2
1
1
2
1
2
2
2
2
1
1
1
2
1
1
1
2
4
1
1
1
1
1
1
1
1
2
1
1
1
2
2
1
1
2
1
2
2
1
2
1
1
1
2
2
1
2
2
1
21
H. THREAD TENSION COMPONENTS
© ANITA www.garudan.cz
22 MP05300_200120 GF-1130-448 MH/L34
© ANITA
Ref. No
19
20
21
22
15
16
17
18
23
24
25
11
12
13
14
7
8
9
10
5
6
3
4
1
2
Part No.
020841
020841A
020841B
020841C
020841D
020841E
020841F
020841G
020841H
020841I
020841J
020841K
020841L
020841M
020841N
020841O
020841P
020841Q
020841R
020841S
020841T
020841U
H. THREAD TENSION COMPONENTS
Part Name
THREAD TENSION ASM.
THREAD POST BASE COMPL.
CYLINDER BLOCK
CYLINDER THIMBLE
PASSING PLATE
PASSING PLATE
TAKE-UP SPRING GUIDE DISC ASM
PAD
PAD
TORSION SPRING
TORSION SPRING BRACKET
PAD
THREAD TENSION NUT
TENSION SPRING NO.1
BOBBIN WINDER TENSION DISC
BOBBIN WINDER TENSION DISC
TENSION NUT
TENSION SPRING
TENSION DISC
THREAD TENSION POST B
PIN
AXIS
LS4C10
LS4C8
SCREW STUD
SCREW STUD
LS4N6 SCREW STUD www.garudan.cz
Qty
1
1
2
2
2
2
2
4
2
1
4
2
2
1
1
1
2
2
1
1
1
2
2
1
1
MP05300_200120 GF-1130-448 MH/L34 23
I. LOWER THREAD WINDER MECHANISM COMPONENT
© ANITA www.garudan.cz
MP05300_200120 GF-1130-448 MH/L34 24
© ANITA
Ref. No
27
28
29
30
23
24
25
26
19
20
21
22
15
16
17
18
35
36
37
38
31
32
33
34
11
12
13
14
7
8
9
10
5
6
3
4
1
2
I. LOWER THREAD WINDER MECHANISM COMPONENT
Part No. Part Name
40126355
BOBBIN DEVICE ASM.
26260109
BOBBIN FITTING BASIS COMPL.
26260307
ADJUSTING PLATE BEARING
26260406
CONNECTING ROD
40126594
ADJUSTING PLATE
26260505
STOP MOVING CARD
40125851
WHEEL SHAPE
26260802
RING
26261008
40126354
BEARING
BEARING SHAFT
26261503
40126550
40125927
40126311
40151791
13718507
RC0560711KP
SM0030601SC
SM6040860TP
SM6031202TP
SM8050502TP
WP0450801SP
FRICTION RUBBER CIRCLE
CENTER BEARING
RUBBER MAT
THREAD TRIMMER
HANDLE
SPRING
RING
SCREW 3*0.5 L=8
SCREW4*8
SCREW
SCREW
FLAT MAT
40126549
40125928
SPRING
POSITIONER
40125844 LIMITED CARD
WS0451040KP
NS6110310SP
SPRING WASHER www.garudan.cz
D3168555H0B BOBBIN WINDER TENSION DISC
B3214047000
21378708
THREAD TENSION POST
THREAD TENSION NUT
11072402
SM8050602TP
21355755
21355706
D3162555B00
NS6110310SP
SS6110810TP
10704807
SCREW
SCREW M5 L=6
LOWER THREAD GUIDE ASM.
FITTING BASE
THREAD GUIDE
NUT 11/64-40
SCREW 11/64-40 L=8
BOBBIN FRICTION WHEEL
Qty
1
1
1
2
1
1
1
1
1
2
1
2
1
3
1
1
3
1
1
1
1
1
2
2
1
1
1
1
1
1
1
2
1
1
1
1
1
1
MP05300_200120 GF-1130-448 MH/L34 25
J. LUBRICATION COMPONENTS (1/2)
© ANITA www.garudan.cz
MP05300_200120 GF-1130-448 MH/L34 26
© ANITA
Ref. No
27
28
29
30
23
24
25
26
19
20
21
22
15
16
17
18
35
36
37
38
31
32
33
34
39
40
11
12
13
14
7
8
9
10
5
6
3
4
1
2
Part No.
21345756
21345707
21345806
21345905
21346358
21346309
21346507
21346408
EA9500B0000
SS7110710SP
21340708
SS7110710SP
CQ2020000OO
21347000
CQ202000000
21347208
021363
21346002
CQ202000000
BT0600402EA
B3538112000
SS4110615SP
J. LUBRICATION COMPONENTS (1/2)
Part Name
ARM ONCE THROUGH OIL FELT ASM.
ARM ONCE THROUGH FELT A
FELT B
FACE ONCE THROUGH FELT
FELT SUPPORT ASM.
FELT
FEED CHANGE FELT
FELT
CLIP CV-70S
SCREW 11/64-40 L=4.3
UPPER FEED OIL BAR PLATE
SCREW 11/64-40 L=5
OIL WICK
TAKE-UP OIL PLATE
OIL WICK
TAKE-UP LUBRICATION FELT
OIL FILTER HEAD
FELT
OIL WICK
OIL TUBE
OIL RETURN TUBE HOLDER
SCREW 11/64-40 L=6
40051503
B3520586000
ARM OIL TANK ASM.
OIL SIGHT WINDOW
21345608 ARM OIL TANK
SQ1110401MZ
SQ1150451MZ
CONNECTING SCREW www.garudan.cz
23630007 TUBE
23630007
23630007
TUBE
TUBE
CQ202000000
EA9500B0100
SS7110830SP
21345103
SS4150915SP
21345202
SS4150915SP
40064409
SQ1110401MZ
B3538112000
OIL WICK
CABLE BAND
SCREW 11/64-40 L= 7.5
LUBRICATION BRACKET
SCREW 15/64-28 L=9
OIL PIPE STAY
SCREW 15/64-28 L=9
CONNECTION SCREW ASM.
CONNECTING SCREW
OIL RETURN TUBE HOLDER
MP05300_200120 GF-1130-448 MH/L34
Qty
2
0.5
0.2
0.6
1
1
1
1
0.25
1
1
1
0.2
0.12
1
1
2
1
2
1
0.7
3
1
1
1
1
1
1
0.2
1
2
1
1
1
1
1
1
1
1
1
27
J. LUBRICATION COMPONENTS (2/2)
© ANITA www.garudan.cz
MP05300_200120 GF-1130-448 MH/L34 28
© ANITA
Ref. No
51
52
53
54
47
48
49
50
41
42
43
44
45
46
59
60
61
62
55
56
57
58
Part No.
SS4110615SP
021365
B3534155000
B1214038000
B3524552000
SS4110815SP
SS6111010SP
23630007
23630007
23630007
23630007
23630007
21338306
SS5090610SP
SS5090610SP
21346606
23630007
010624
021364
010623
LM8
021360
J. LUBRICATION COMPONENTS (2/2)
Part Name
SCREW 11/64-40 L=6
FILTER
PLUNGER
PLUNGER SPRING
PLUNGER THRUST PLATE
SCREW 11/64-40 L=8
SCREW 11/64-40 L= 9.5
TUBE
TUBE
TUBE
TUBE
TUBE
LUBRICATION FELT PRESSER
MUTUAL VERTICAL CHANGE FELT
SCREW 3/16-28 L= 7.0
PIPE SUPPORT
TUBE
NUT 11/64-40
COVER
SCREW
NUT 8
THROTTLE SLEEVE www.garudan.cz
Qty
0.1
0.5
1
1
2
0.36
0.5
0.22
1
1
1
1
1
1
1
1
1
1
1
1
0.22
1
MP05300_200120 GF-1130-448 MH/L34 29
K. AUTOMATIC PRESSER LIFTING MECHANISM
© ANITA www.garudan.cz
MP05300_200120 GF-1130-448 MH/L34 30
© ANITA
Ref. No
11
12
13
14
7
8
9
10
5
6
3
4
1
2
K. AUTOMATIC PRESSER LIFTING MECHANISM
Part No. Part Name
ACQ40*15
AIR CYLINDER
LS8A20
SCREW M8 L=20
21356506
CYLINDER CONNECTING SCREW
NM6080001SE
NUT M8
SD0720331SP
HINGE SCREW D= 7.24 H= 3.3
21356605
LEVER A
21356803
LEVER B
LS5A10
SCREW M5X0.8 L=10
21356704A
SPL4-01
SHAFT
ELBOW
21356308
21356407
SS6151040SP
21356704B
CYLINDER STAY(FRONT)
CYLINDER STAY(REAR)
SCREW 15/64-28 L=10
NUT 5/16-24T
Qty
4
1
1
1
1
2
1
2
1
1
1
1
1
4 www.garudan.cz
MP05300_200120 GF-1130-448 MH/L34 31
L. THREAD STAND COMPONENTS
© ANITA www.garudan.cz
MP05300_200120 GF-1130-448 MH/L34 32
© ANITA
Ref. No
11
12
13
14
7
8
9
10
5
6
3
4
1
2
15
16
17
18
19
20
Part No.
22930358
22931109
22931000
22930903
22930804
SM6061610SC
22930705
22931406
22930507
22931308
22931307
SM4051408SE
NM6050001SE
22930309
22931208
WS0510002KN
NM6050001SE
NM6160511SE
WP1612616SE
WS1643202KP
L. THREAD STAND COMPONENTS
Part Name
THREAD STAND ASM.
SPOOL RETAINER
SPOOL PIN
SPOOL REST CUSHION
SPOOL REST
SCREW M6 L=16
THREAD GUIDE ARM JOINT
SPOOL REST ROD RUBBER CAP
SPOOL REST ARM
SPOOL REST ROD UPPER
SPOOL REST ROD JOINT
SCREW M5 L=14
NUT M5
SPOOL REST ROD LOWER
THREAD GUIDE
SPRING WASHER
NUT M5
NUT M16X1.5
WASHER 16X30X2.6
SPRING WASHER www.garudan.cz
Qty
〈 1 〉
〈 2 〉
〈 2 〉
〈 1 〉
〈 2 〉
〈 2 〉
〈 2 〉
〈 1 〉
〈 2 〉
〈 1 〉
1
〈 2 〉
〈 2 〉
〈 2 〉
〈 2 〉
〈 2 〉
〈 2 〉
〈 1 〉
〈 2 〉
〈 1 〉
MP05300_200120 GF-1130-448 MH/L34 33
M. AUTOMATIC BACK-TACK COMPONENTS
© ANITA www.garudan.cz
MP05300_200120 GF-1130-448 MH/L34 34
© ANITA
Ref. No
11
12
13
14
7
8
9
10
5
6
3
4
1
2
19
20
21
22
15
16
17
18
23
24
SPC4-1
PST01
SD0800402TP
NS6150430SP
22656102
SS7120760SP
22656003
SS4120615SP
13515606
10120004
11100500
21349105
M. AUTOMATIC BACK-TACK COMPONENTS
Part No. Part Name
21348958
WINDOW PLATE ASM.
SDA32*15
JIG CYLINDER
LS6A16
SCREW M6 L=16
PD6
WASHER 6
21348602
CYLINDER CONNECTING SCREW
LM6
NUT M6
21348503
FITTING BASE
SS7151210SP
SCREW 15/64-28 L=12
21348701
SD0800352SP
BACKWARD FEED LINK
HINGE SCREW D= 8 H= 3.5
HALF UNION
MUFFLER
HINGE SCREW D= 8 H= 4
NUT 15/64-28
REVERSE FEED LINK (1)
SCREW 3/16-28 L= 7.0
SPRING SUSPENSION
SCREW 3/16-28 L=6
SPRING
SPRING SUSPENSION
REVERSE FEED LEVER STOPPER
CYLINDER PACKING
SS7111810SP SCREW 11/64-40 L=18
21348909 WIDOW PLATE D www.garudan.cz
Qty
1
1
1
1
1
2
1
2
1
1
2
2
1
1
1
1
1
1
1
1
1
1
1
1
MP05300_200120 GF-1130-448 MH/L34 35
N. DL-MECHANISM COMPONENTS
© ANITA www.garudan.cz
MP05300_200120 GF-1130-448 MH/L34 36
© ANITA
Ref. No
11
12
13
7
8
9
10
5
6
3
4
1
2
Part No.
SDA32*15
PST-01
SM6044002TP
21438403
LM8
21438502
SD0600403TP
SD0600454TP
21438601
SS6111610SP
21437306
21437207
SPL4-1
N. DL-MECHANISM COMPONENTS
Part Name
JIG CYLINDER
MUFFLER
SCREW
CYLYNDER CONNECTING SCREW
NUT M8
MUTUAL VERTICAL LINK
HINGE SCREW
SHOULDER SCREW
MUTUAL VERTICAL LINK SPASER
SCREW 11/64-40 L=16
WINDOW PLATE E PACKING
WINDOW PLATE F
ELBOW
Qty
1
1
1
1
2
1
1
1
1
2
1
1
1 www.garudan.cz
MP05300_200120 GF-1130-448 MH/L34 37
O. AIR MECHANISM COMPONENTS
© ANITA www.garudan.cz
MP05300_200120 GF-1130-448 MH/L34 38
© ANITA
Ref. No
11
12
13
14
7
8
9
10
15
16
17
18
5
6
3
4
1
2
Part No.
021701
021723
021703
021704
021705
SPC8-01
SPL6-01
WP0621016SH
LM6
040151
022238
APU0604 L=500
APU0425 L=500
021658A
SS4110815SP
021654
SS7110710SP
021726
O. AIR MECHANISM COMPONENTS
Part Name
AIR APPARATUS (B) ASM.
MOUNTING PANEL
SCREW D=4.1 L=20
SCREW M6 L=10
FILTER REGULATOR
NIPPLE
NIPPLE
FLAT PAD
NUT
SCREW
ELECTROMAGNETIC VALVE ASM.
TUBE Φ6
TUBE Φ4
SAFETY SWITCH
SCREW
5RANGE SWITCH ASM.
SCREW
PIPE CLAMP www.garudan.cz
Qty
6
1
1
1
2
3
1
2
3
1
2
1
1
1
2
2
1
1
MP05300_200120 GF-1130-448 MH/L34 39
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project