Treadmill

Model No:

JX200

Retain this owner’s manual for future reference

Read and follow all instructions in this owner’s manual

Version A

1

INDEX

5.

6.

7.

8.

1.

2.

3.

4.

OVERVIEW DRAWING

IMPORTANT SAFETY INSTRUCTIONS

GROUNDING INSTRUCTIONS

PRE-ASSEMBLY CHECK LIST

ASSEMBLY STEPS

CAUTION

MAINTENANCE

COMPUTER OPERATION INSTRUCTIONS

6

7

8

9

2

3

4

5

1

1.

OVERVIEW DRAWING

2

2.

IMPORTANT SAFETY INSTRUCTIONS

When using this product, basic precautions should always be followed, including the following:

Please read the instruction carefully before starting to use this product.

Danger

– To reduce the risk of electric shock ：

1.

Always unplug this product from the electrical outlet immediately after using and before cleaning the treadmill.

Warning

– To reduce the risk of burns, fire, electric shock, or physical injury ：

1.

The product should never be left unattended while plugged in.

Unplug the product from the outlet when not in use or before putting on or taking off clothes and other belongings.

2.

To avoid any danger, close supervision is necessary when this production is used by children, invalids or disabled persons.

3.

Be sure to use the product only for its intended use as described in this manual. Do not use any attachment(s) not recommended by the manufacturer

4.

Never operate the product if it has a damaged cord or plug, if it is not working properly, if it has been damaged, or dropped into water. Please return the product to the service center of seller for examination and repair.

5.

Do not carry this product by the supply cord or use the cord as a handle 。

6.

Keep the cord away from hot surfaces or ground 。

7.

Never operate the product with the air vents blocked. Keep the air vents free of lint, hair, etc 。

8.

Never drop or insert any objects into any vent of the treadmill 。

9.

Do not use or operate outdoors 。

10.

Do not operate where aerosol (spray) products are being used or where oxygen is thin 。

11.

Before turning the product power off, turn all controls to the off position then remove the plug from the outlet 。

12.

Connect the product to a properly grounded outlet only 。

13.

The product is only intended for household use.

14.

If the power cord is damaged, be sure to ask the manufacturer for replacement to avoid accidents .The seller and correlative qualified professionals are as well as eligible.

3

3.

GROUNDING INSTRUCTIONS

The products must be grounded first. If malfunction or breakdown occurs, grounding will provide a path of least resistance for electric current to reduce the risk of electric shock.

The product is equipped with an equipment-grounding conductor and a grounding plug.

The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

Danger

– Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or serviceman if you doubt whether the products are properly grounded. Do not modify the plug provided with the product – if it will not fit the outlet, have a proper outlet install by a qualified electrician.

The products is for use on normal 220V-240V circuit and contains a plug that should look like the one illustrated in the figure. Make sure that the product is connected to an outlet having the same configuration as the plug. No adaptor should be used with the product.

Figure

Grounding methods

GROUNDED

OUTLET

GROUNDED PIN

4

ITEM

A

B

C

D

4.

PRE-ASSEMBLY CHECK LIST

Description

Frame

Bottle

Cover

Emitter

Qty ITEM

1 a

1 b

2 c

1 d e f f

Description Qty

Truss Hex Screw M8xP1.25x60

Truss Hex Screw M8xP1.25x25

Hex Wrench 5mm

Hex Wrench 6mm

Safety Key/Clip

Power Cord

SILICON

1

1

1

1

1

2

4 a b c d e g

A f

C

D

5

5.

ASSEMBLY STEPS

Two persons are required to finish the assembly steps.

(Caution!! Please follow exactly the assembly steps below to avoid injury.)

1.

1. Put up the two computer handrail tubes of

Frame (A) as shown in the right drawing and tighten with hex screw (c). Then wedge left and right covers.

PS. To avoid danger, always assemble the treadmill with more than two people, do not assemble by yourself.

2. Then put up the left and right uprights as shown in the right drawing and tighten with hex screw (b).

PS. To avoid danger, always assemble the treadmill with more than two people, do not assemble by yourself.

b b b b a

C a

C

6

6.

CAUTION

Note: The Cylinder contains high pressure gas. Please avoid crash with other objects to avoid danger.

Note: If the Cylinder is hit, it might be damaged and cause the usage not smooth. The treadmill might fall while folding.

Note: This treadmill has four segments of shock absorber function. Different colors have different rigidity. Pull out the knob and turn it to choose the rigidity. Four colors represent four kind of rigidity.

The rigidity is from soft to hard according to the color red, yellow, blue and black.

7

This treadmill has a foldable mechanism for storage.

Stop all movements (including stopping the belt and remove power cord) before attempting storage. Then fold the main frame in the direction shown in the picture. Be sure the fixing plate inserts the tube of base frame. On the contrary, if you want to use treadmill, step on the fixing plate as the direction shown in the drawing. When it disjoins from tube of base frame, pull down the main frame as shown.

Stand beside the treadmill and the main frame will slowly fold to the ground automatically.

(PS. 1. To prevent from danger, be careful of children nearby. If you want to move the treadmill, fold the treadmill first, then move and hold your hands at the rear of the adjustment box; then make the treadmill descend until the wheels can be moved smoothly. You can then move the treadmill. )

(P.S. 2. DO NOT move the treadmill on uneven ground.)

(P.S. 3. To avoid injury, do not stand under the frame when the frame is descending.)

8

7.

MAINTENANCE

1. If the belt tends to move off from the centre, stop the treadmill. Take the L-shaped wrench and adjust the Hex

Screw in the Rear End Cap. For example, if the running belt is moving towards the left side, tighten the left Hex

Screw about 1/4 turn (clockwise). If the running belt is moving towards the right side, tighten the right Hex

Screw about 1/4 turn (clockwise). Switch on the treadmill after it has been adjusted. If you find that the belt has not moved to the proper position, please repeat the steps above.

Don’t use the treadmill until the running belt returns to the centre position.

(P.S. 1. This procedure is very important, if the belt is not in the centre, be sure to follow the above steps.)

(P.S. 2. The position of the running belt might not stay precisely in the centre, and the situation varies with how end-users use and the weight of end-users. No need to adjust the belt if it doesn’t rub against the parts aside.)

2. Depending on the usage of the product, please apply

SILICON on the board according to the chart below.

Use the L-shaped wrench to unscrew the bolt inside the

Rear Roller. Then pull the belt up and daub some

SILICON to the centre of the board. After that, adjust the belt to the centre of the deck, followed by tightening the screw to the original set.

(PS. When the belt is sliding, please follow the above method to lubricate the running belt.)

KGS/LBS

KGS

LBS

Speed

6KM/hr Below

6~12KM/hr

12KM/hr Above

4mile/hr Below

4~8mile/hr

8mile/hr Above

Interval

1 year

6 months

3 months

1 year

6 months

3 months

Note: This maintenance is intended for household use.

If used for business, it is suggested to examine the product every other month

9

8.

COMPUTER OPERATION INSTRUCTIONS

I. General Operation

1.

Turn on the treadmill.

2.

Put the safety key in the recess of the console.

At this time, the buzzer will sound for warning and the window will display” □ 0 ”, which means the treadmill has entered into the start/ready state. Under this mode, you can grip hand pulse sensor to detect the heart beat value.

3.

Press and the MANUAL LED will light. The treadmill will start with a speed of

1.0km/hr. During workout, press keys to increase/ decrease speed( also can press fast speed buttons press to contr ol the angles

to instantly choose the speed you need) or

of inclination . Press and the treadmill will stop running( press hold the one time, the window will display . If press the second time and

button for 3 seconds, treadmill wi ll automatically reset to the

START/READY position)

4.

Under start/ready state, you can press into other function

** If the safety key/clip is not placed in the recess of the console, all windows will display

“----”, which means the treadmill doesn’t enter into start/ready state.

10

** When the SAFETY KEY is taken off and then replaced, the treadmill will not reposit from any position it is. You need to press start key to perform the reposition.

** When the power is on, the treadmill will not reposit from any position it is. You need to press start key to perform the reposition.

** Under start/ready status, press stop key for 5 seconds, the treadmill will reposit from any position it is.

**During performing any program, by press stop key, the program will stop. If users want to resume to the program, press start key or press stop key again to leave the program and back to start/ready status.

MODE Function key

5.

Under start/ready mode, press and MANUAL LED will flash, which means into function selection mode. Under this mode, press “ or ＂ to switch

MANUAL 、 P1~P5 and HRC LED light.

6.

MANUAL function ：

6.1.

When MANUAL LED is flashing, press and the MANUAL LED will stop flashing and keep light.

TIME LED will flash, at this time you can adjust the time.

6.2.

Press

“

and the motor will start with a speed of 1.0km/hr , at this time press

or ” to control the incline angles and the speed of the treadmill.

7.

P1~P5 Program Control Function (each PROGRAM has 12 segments)

7.1.

When the MANUAL LED begin to flash, you can press “ the desired LED of P1~P5 begin to flash, press

or ” until to confirm, after you enter the program control function, the corresponding light will keep on lighting.

7.2.

At this time, the CALORIES window will display the exercise intensive level( L1~L5 ) you can press “ or ＂ to select the desired level and press to co nfirm.

7.3.

After the level is selected, the TIME window flashes, at this time you can press

“ or ＂ to change the time, after the desired time is set, press to confirm and the TIME window will stop flashing.

** Time preset value ： 25(min)

11

Range of time ： 5~99(min)

7.4.

Press and the treadmill runs according to the preset value of the program.

The speed and inclination of program’s 12 stages will change circularly according to the preset values. At the first time, the first segment will last 2 minutes, then the following will each last for 1 minute, when the time is achieved, speed and inclination will change directly.(During workout, press “ or ＂ directly to control the speed.)

7.5.

During the function setting of P1~P5 , if press once, the unedited are preset values, press “

， the treadmill will start to run at

or ＂ and then you can change the preset values of PROGRAM ， but in the next stage, the values will be reset to the original values of the PROGRAM.

7.6.

For this treadmill, P1 is defined program, the meaning is shown below:

P1 9 HOLE ： This program is based on 3500m ， after you run 3500m according to the preset value ， the program is then finished, and the treadmill will stop. This mode simulates the landform of a golf course ， the difficult level is decided by the change of upgrade and downgrade.

7.7.

In each PROGRAM ， there is one minute for the warm exercise before L1~L3 is executed, the speed is defined by the start speed of each LEVEL.

12

Refer to the below PROGRAM figures for the preset value ：

13

14

8.

HRC function ： (This function must be attached with chest belt pulse to finish).

8.1.

The program aims to exercise heartbeat. When operating, the heartbeat value is equal to the pre-set value, the angle and speed will keep steady to maintain the heartbeat value in certain range to achieve the exercising effect.

8.2.

When the MANUAL LED is blinking, press “ or ＂ until the

HRC LED you want stops blinking. Press of HRC will stop blinking and continue to light. The program will order you to input value according to operating style below.

8.3.

LED of AGE light flashes, you can press or to adjust age. After setting, press

Age Pre-set ： 30

to another option.

Range of age ： 13~80 ， Step is 1

8.4.

At this time LED of PULSE light flashes, the mode will request you to input heartbeat value. The value will change according to the age and please refer to the attached table in the rear of this indication. Then select the suitable value in the table.

You can press or to adjust heartbeat value. If you don’t make any change, press option.

and mode will start according to pre-set value and turn to next

8.5.

TIME window starts flashing, mode will request you to input time value. You can press or to se t sp ort time you need. Or press start move with no countdown.

Range of time value ： 5 ~99 min

directly to

15

** The chart below will show the relationship between different age and heart rate of this product of

HRC function ：

BPM BPM

Age

H preset L

BPM

Age

H preset L

Age

H preset L

BPM

Age

H preset L

13 197 124 124 31 180 113 113 49 162 103 103 67 145 92 92

14 196 124 124 32 179 113 113 50 162 102 102 68 144 91 91

15 195 123 123 33 178 112 112 51 161 101 101 69 143 91 91

16 194 122 122 34 177 112 112 52 160 101 101 70 143 90 90

17 193 122 122 35 176 111 111 53 159 100 100 71 142 90 89

18 192 121 121 36 175 110 110 54 158 100 100 72 141 90 89

19 191 121 121 37 174 110 110 55 157 99 99 73 140 90 88

20 190 120 120 38 173 109 109 56 156 98 98 74 139 90 88

21 189 119 119 39 172 109 109 57 155 98 98 75 138 90 87

22 188 119 119 40 171 108 108 58 154 97 97 76 137 90 86

23 187 118 118 41 170 107 107 59 153 97 97 77 136 90 86

24 186 118 118 42 169 107 107 60 152 96 96 78 135 90 85

25 185 117 117 43 168 106 106 61 151 95 95 79 134 90 85

26 184 116 116 44 167 106 106 62 150 95 95 80 133 90 84

27 183 116 116 45 166 105 105 63 149 94 94

28 182 115 115 46 165 104 104 64 148 94 94

29 181 115 115 47 164 104 104 65 147 93 93

30 181 114 114 48 163 103 103 66 146 92 92

16