ADT CTRT0650W(G) User Instructions


Add to my manuals
21 Pages

advertisement

ADT CTRT0650W(G) User Instructions | Manualzz

Operating Manual

USER'S INSTRUCTIONS

High Resolution

DNR Day/Night

Color Camera

CTRT2812W(G) / CTRT0650W(G)

USER’S MANUAL

◑ General Features

◑ Installing & Adjusting

Dimension & Specification

◑ OSD Control Button

◑ Camera Menu Set Up

1. Menu Set Up

2. Lens Setting

3. Exposure Setting

4. White Balance Setting

5. SSNR Setting

6. Backlight Setting

7. DNR3 Setting

8. Day/Night Setting

9. Special Setting

10. Exit Setting

◑ Trouble Shooting

Contents

10

11

12

13

8

9

7

7

14

18

19

3

4

5

6

2

USER’S MANUAL

General Features

Ultra High Sensitivity

- The built-in high sensitivity COLOR CCD produces a clear image even in 0Lux(B/W, IR-LED ON) or lower illumination.

600TV Lines

- By adopting a diagonal 6mm(1/3") 410,000 (NTSC) pixel, 470,000(PAL) pixel SONY CCD, the camera produces clear picture quality with a horizontal resolution of 600 TV lines for color and a horizontal resolution of 700TV lines for BW mode.

DNR3

- The high-performance W-V DSP chip effectively removes low-light gain noise and ghosting to provide clear images even in dark environments.

Day & Night

- This camera has a function that automatically selects the mode that is appropriate for daytime or night-time conditions. The COLOR mode operates in daytime conditions to provide optimum colors, and BW mode operates in night-time conditions to enhance the definition of the image.

SSNR

- For images with high contrast between bright and dark Areas from difficult lighting conditions such as backlighting, this camera selectively illuminates darker Areas while retaining the same light level for brighter Areas to even out the overall brightness.

Miscellaneous Functions

- HLC(High Light Compensation), SENS-UP, FLIP(H/V-REV), D-ZOOM, SHARPNESS, MOTION

DETECTION and PRIVACY functions are provided.

Disk Saving Effects

- Up-most and advanced DNR technology camera picture quality has a disk saving effects due to

Image sizes are smaller than standard CCTV camera image.

Controlled by OSD Menu

- The camera can be controlled by selecting the menu text displayed on the monitor screen.

3

USER’S MANUAL

INSTALLING & ADJUSTING

1. Installation

- Place the mounting plate on a flat installation surface

and mount with the provided screws.

- Feed the cable through the center of the mounting plate.

- Place the camera body in the mounting plate socket

and hold.

- Then place the outer plate over the camera body &

mounting plate and tighten side screws to lock the

camera into place.

- Loosen side screws to adjust camera angle as needed,

then tighten the side screws to lock into place.

2. Focus/Zoom Screw

- To widen the viewing angle turn the Zoom screw

to "W"(Wide) to obtain a closer view turn it to

"T"(Tele)

- Turn the Focus screw to "N"(Near) or "

"

(Far) untill the sharpest Focus is made.

4

USER’S MANUAL

DIMENSION & SPECIFICATION

1. Dimension & Connection

Dimension Connection

2. Specification

Image Pick-Up Device

TV System

Total Pixels

Effective Pixels

Scanning Frequency

Scanning System

Synchronization

Resolution

Minimum Illumination

S/N Ratio

Video Output

Electronic Shutter Speed

OSD

SSDR

BLC

Day & Night

Gain Control

White Balance

SENS-UP

Motion Detection

Privacy Masking

SSNR III (Digital Noise Reduction)

Digital Zoom

DIS (Digital Image Stabilizadion)

Sharpness

Filp / Mirror

Power Supply

Power Consumption

Lens

Operational Temp.

Storage Temp.

Dimension

Weight

1/3” Sony Super HAD CCD

NTSC

811(H) * 508(V)

768(H) * 494(V)

15.734KHz(H) & 59.94Hz(V)

2:1 Interlace

Internal / Line-Lock

600TV Lines

IR LED OFF: 0.15 Lux, IR LED ON: 0 Lux

More than 52dB

CVBS: 1.0Vp-p / 75Ω

NTSC=(1/60sec~1/120,000sec) / PAL=(1/50sec~1/120,000sec)

Available

On / Off (Level adjustable)

BLC / HLC / OFF

Color / BW / AUTO

Low / High / Off

ATW / Outdoor / Indoor / Manual / AWC (1,700°K ~ 11,000°K)

Auto / Off (Selectable x2 ~ x512)

On / Off (8 Programmable Zones)

On / Off (12 Programmable Zones)

On / Off (Level adjustable)

On / Off (x1 ~ x16)

On / Off

On / Off (Level adjustable)

On / Off

DC 12V / AC 24V Dual Voltage

IR LED OFF 120mA(DC), IR LED OFF 70mA(AC) / IR LED ON 670mA(DC), IR LED ON 240mA(AC)

DC Auto Iris Varifocal Lens

~10 ~ +50 Deg C. RH95% MAX.

~20 ~ +60 Deg C. RH95% MAX.

140mm(W) * 111mm(H) * 180mm(D)

1800g

5

USER’S MANUAL

OSD Control Button

1. OSD button could be used when it needs to OSD control.

▲ Up button: Moves the cursor upwards. Use this button to select an item

or adjust the parameters.

▼ Down button: Moves the cursor downwards. Use this button to select an

item or adjust the parameters.

◀ Left button: Moves the cursor to the left. Use this button to select or

adjust the parameters of the selected item. The parameter changes

each time this button is pressed.

▶ Right button: Moves the cursor to the right. Use this button to select or

adjust the parameters of the selected item. The parameter changes each

time this button is pressed.

◎ Set button: Executes selections and displays a submenu for an item with

the mark.

6

USER’S MANUAL

Menu Setup

1. Press the Function Setup switch.

- Main setup menu is displayed on the monitor screen.

1.LENS

MAIN SETUP

DC

2.EXPOSURE

3.WHITE BAL

4.SSNR

5.BACKLIGHT

6.DNR3

7.DAY/NIGHT

8.SPECIAL

9.EXIT

ATW

OFF

OFF

ON

AUTO

SAVE

2. Select a desired function using the Function Setup switch.

- Place the cursor over a desired item.

3. Set up a selected item by using the Function Setup switch.

4.

To finish the setting, select 'EXIT' and press the Function Setup switch.

NOTE

■ An item with the

◀ icon also has sub menus. To select a sub menu, select an item with the icon and press the Function Setup switch.

■ An item with the - - - icon is unavailable due to function settings.

Lens Setting

Using this function, you can control the screen brightness.

1. When the SETUP menu screen is displayed, select 'LENS' by using

the Function Setup switch so that the arrow indicates 'LENS'.

2. DC : You can adjust the minimum shutter and maximum value of ESC

shutter mode.

MAIN SETUP

1.LENS

2.EXPOSURE

3.WHITE BAL

DC

ATW

3. THE Lens mode has sub menu items as listed below.

- BRIGHTNESS : Adjusts the video brightness.

7

USER’S MANUAL

- FOCUS ADJ : To adjust the DC lens focus correctly, you must activate the Focus Settings mode under each lens menu. Activate the Focus Settings mode, adjust the lens focus, and then deactivate the settings mode.

☞ NOTE

■ If color rolling occurs when using a DC lens, set Shutter to Fixed (---).

Exposure Setting

1.LENS

MAIN SETUP

DC

2.EXPOSURE

3.WHITE BAL ATW

1. When the SETUP menu screen is displayed, select 'EXPOSURE' by using the

Function Setup Switch.

2. Select a desired mode using the Function Setup switch.

EXPOSURE SETUP

1.BRIGHTNESS

2.SHUTTER

3.AGC

4.SENS-UP

5.RETURN

25

- - -

HIGH

OFF

◆ SHUTTER : You can select either auto or manual shutter.

* --- : Shutter speed is fixed at 1/60sec(1/50sec)

* ESC : Select this to control the shutter speed automatically. If ESC is selected, the shutter speed is automatically controlled depending on the ambient illumination of the subject.

* MANUAL : You can control shutter speed manually.

(NTSC MODEL : 1/60~1/120,000, PAL MODEL : 1/50~1/120,000)

* A.FLK : Select this when you see picture flicker, this can happen when the frequency of the local lighting clashes with the camera.

8

NOTE

■ When the SHUTTER is set to MANUAL or A.FLK mode, SENS-UP will be disabled.

USER’S MANUAL

◆ AGC(AUTO GAIN CONTROL) : The higher the gain level, the brighter the screen but the higher the noise.

* OFF : Deactivates the AGC function.

* LOW : Allows automatic gain control from 5.3dB to 32dB.

* HIGH : Allows automatic gain control from 5.3dB to 37dB.

◆ SENS-UP : When it is night or dark, the camera automatically detects the light level and maintains a clear picture if this mode is activated.

* OFF : Deactivates the SENS-UP function.

* AUTO : Activates the SENS-UP function.

RETURN : Select this to save the changes in the EXPOSURE menu and return to the SETUP menu.

NOTE

■ If you press the Function Setup switch to ‘AUTO’ mode, you can adjust brightness by increasing or decreasing the shutter speed. (x2 ~ x512)

■ Note that the higher the zoom level, the brighter the screen, but the more likely there will be a ghosting effect.

■ It is normal for Noise, Spots and Whitish symptoms to appear in SENS-UP mode when the D-ZOOM level is increased.

White Balance (White Bal) Setting

Use the White Balance function to adjust the screen color.

1. When the SETUP menu screen is displayed, select 'White Bal' by using the Function

Setup switch so that the arrow indicates 'White Bal'.

2. Select a desired mode using the Function Setup switch.

1.LENS

MAIN SETUP

DC

2.EXPOSURE

3.WHITE BAL ATW

9

USER’S MANUAL

※ Select one of the following 5 modes, as appropriate for your purpose.

ATW : Select this when the color temperature is between 1,700˚K and 11,000˚K.

OUTDOOR : Select this when the color temperature is between 1,700˚K and 11,000˚K.

(sodium light inclusion)

INDOOR : Select this when the color temperature is between 4,500˚K and 8,500˚K.

◆ MANUAL : Select this to fine-tune White Balance manually. Set White Balance first by using the

ATW or AWC mode. After that switch to MANUAL mode, fine-tune the White Balance and then press the Function Setup switch.

AWC→SET : To find the optimal luminance level for the current environment, point the camera towards a sheet of white paper and press the Function Setup switch. If the environment changes, readjust it.

NOTE

■ White Balance may not work properly under the following conditions. In this case select the AWC mode.

When the color temperature of the environment surrounding the subject is out of the control range (e.g. clear sky or sunset).

When the ambient illumination of the subject is dim.

If the camera is directed towards a fluorescent light or is installed in a place where illumination changes dramatically, the White Balance operation may become unstable.

SSNR Setting

SSNR illuminates darker spots of an image while retaining the same light level for brighter spots to even out the overall brightness of images with high contrast between bright and dark spots.

MAIN SETUP

1.LENS

2.EXPOSURE

3.WHITE BAL

4.SSNR

DC

ATW

OFF

1. When the SETUP menu screen is displayed, select 'SSNR' by using the switch so that the arrow indicates 'SSNR'.

2. Use the switch to change the SSNR level according to the contrast between bright and dark areas.

10

USER’S MANUAL

Backlight Setting

Unlike conventional cameras, the SIR-4160 is designed to deliver a distinctive subject and background at the same time, even when the subject is backlight, by using the features of the proprietary W-V DSP chip.

1. When the SETUP menu screen is displayed, select 'BACKLIGHT' by using the Function

Setup switch so that the arrow indicates 'BACKLIGHT'.

1.LENS

MAIN SETUP

DC

2.EXPOSURE

3.WHITE BAL

4.SSNR

5.BACKLIGHT

6.DNR3

7.DAY/NIGHT

8.SPECIAL

9.EXIT

ATW

OFF

OFF

ON

AUTO

SAVE

2. Select a desired mode using the Function Setup switch.

◆ BLC : Enables a user to directly select a desired area from a picture, and to view

the area more clearly.

◆ HLC (High Light Compensation) : If the scene contains extremely bright light areas

such as; from car headlights, the light can mask out much of the on-screen detail

- LEVEL : Adjust level of the HLC function.

- LIMIT : Enable to change the operating condition.

- MASK COLOR/TONE : Change the color / transparency of the masking area.

(Black, Red, Blue, Cyan, Magenta)

- TOP/BOTTOM/LEFT/RIGHT : Adjust the area to be enhanced

◆ OFF : Not being used

2. Select a desired mode using the Function Setup switch and press the Function Setup switch.

◆ Select 'BLC' to adjust the area to be

enhanced then adjust the level.

◆ Select 'BLC' to adjust the area to be

enhanced then adjust the level.

11

USER’S MANUAL

BLC SETUP

LEVEL

TOP

BOTTOM

LEFT

RIGHT

Press Set to Return

LOW

38

109

54

121

HLC SETUP

LEVEL

LIMITS

MASK COLOR

MASK TONE

TOP

BOTTOM

LEFT

RIGHT

Press Set to Return

MIDDLE

NIGHT ONLY

BLACK

120

5

1

5

172

NOTE

■ Because there can be a difference in the effectiveness of HLC according to the amount of light area in the screen, optimize the installation angle for the best HLC performance.

■ When dark, the HLC is only activated when a bright light exceeding a specific size in

NIGHT ONLY mode.

■ The HLC is not activated in day light or when bright light is not present at night in NIGHT

ONLY mode.

■ BLC Function doesn't work in the B/W mode of the DAY/NIGHT menu.

DNR3 Setting

This function reduces the background noise in a low luminance environment.

1. When the SETUP menu screen is displayed, select 'DNR3' by using the Function

Setup switch so that the arrow indicates 'DNR3'.

1.LENS

MAIN SETUP

DC

2.EXPOSURE

3.WHITE BAL

4.SSNR

5.BACKLIGHT

6.DNR3

7.DAY/NIGHT

8.SPECIAL

9.EXIT

ATW

OFF

OFF

ON

AUTO

SAVE

2. Select a desired mode using the Function Setup switch.

◆ OFF : Deactivates DNR3. Noise is not reduced.

◆ ON : Activates DNR3 so that noise is reduced.

12

USER’S MANUAL

3. Set the DNR3 mode to 'ON' and press the Function Setup switch. Then you can adjust the noise reduction level.

NOTE

■ You cannot set the DNR3 to ‘ON’ or ‘OFF’ when the AGC mode of the EXPOSURE menu is ‘OFF’.

■ When adjusting the noise reduction level in the DNR3 mode, remember that the higher the level set, the more the noise level will be reduced, as will the brightness of the image.

Day/Night Setting

You can display pictures in color or black and white.

1. When the SETUP menu screen is displayed, select 'DAY/NIGHT'by using the Function

Setup switch so that the arrow indicates 'DAY/NIGHT'.

1.LENS

MAIN SETUP

DC

2.EXPOSURE

3.WHITE BAL

4.SSNR

5.BACKLIGHT

6.DNR3

7.DAY/NIGHT

8.SPECIAL

9.EXIT

ATW

OFF

OFF

ON

AUTO

SAVE

2. Select a desired mode using the Function Setup Switch according to the picture display you want.

◆ COLOR : The picture is always displayed in color.

◆ B/W : The picture is always displayed in black and white.

- BURST MODE : You can turn on or off the burst signal on B/W mode.

- IR MODE : When IR LED is turned on in B/W, the objects can be clearly identified due

to the function that decreases screen saturation of objects within a short distance.

- TOP/BOTTOM/LEFT/RIGHT : Adjust the range according to the location of objects.

- IR LEVEL : Select LOW when objects appears within a short distance or select HIGH when objects appears within a long distance on the screen.

B/W MODE SETUP

1.BURST MODE

2.IR MODE

3.IR LEVEL

4.RETURN

ON

ON

HIGH

13

USER’S MANUAL

◆ AUTO : The mode is switched to 'Color' in a normal environment, but switches to 'B/W' mode when ambient illumination is low. To set up the switching time for AUTO mode, press the Function

Setup switch. You can turn on or off the burst signal on B/W mode.

- BURST MODE : You can turn on or off the burst signal

on B/W mode.

- DURATION : You can select brightness of illumination

about changing the day/night mode.

- DWELLTIME : You can select the duration time about

changing the day/night mode.

→3s, 5s, 7s, 10s, 15s, 20s, 30s, 40, 60s

AUTO SETUP

1.BURST MODE

2.COLOR→B/W

DURATION

DWELL TIME

3.B/W→COLOR

DURATION

DWELL TIME

4.RETURN

ON

FAST

3SEC

FAST

10SEC

FAST

SLOW

COLOR→B/W

2.5 lux

1 lux

B/W→COLOR

5 lux

10 lux

* The day/night switching point of the

camera can be adjusted.

NOTE

■ When AGC in the EXPOSURE menu is 'OFF', '---' mode operates as like selecting 'COLOR' mode and 'AUTO' mode can not be selected.

Special Setting

1. When the SETUP menu screen is displayed, select 'SPECIAL' by using the Function Setup switch so that the arrow indicates 'SPECIAL'.

1.LENS

MAIN SETUP

DC

2.EXPOSURE

3.WHITE BAL

4.SSNR

5.BACKLIGHT

6.DNR3

7.DAY/NIGHT

8.SPECIAL

9.EXIT

ATW

OFF

OFF

ON

AUTO

SAVE

14

2. Select a desired mode using the Function Setup switch.

SPECIAL

1.IMAGE ADJ

2.CAM TITLE

3.SYNC

4.MOTION DET

5.PRIVACY

6.DIS

7.LANGUAGE

9.RETRUN

OFF

INT

OFF

OFF

OFF

ENGLISH

USER’S MANUAL

◆ IMAGE ADJ. :

1) When the SETUP menu screen is displayed, select 'IMAGE ADJ' by using the

Function Setup switch so that the arrow indicates 'IMAGE ADJ'.

2) Select a desired mode using the Function Setup switch.

IMAGE SETUP

1.V-REV

2.H-REV

3.D-ZOOM

4.FONT COLOR

5.SHARPNESS

6.MONITOR

7.RETURN

OFF

OFF

WHITE

ON

LCD

* V-REV : You can flip the picture vertically on the screen.

* H-REV : You can flip the picture horizontally on the screen.

* D-ZOOM : You can use a digital zoom of x1 ~ x16.

* FONT COLOR : You can change the OSD font color. (White, Yellow, Green, Red, Blue)

* SHARPNESS : As you increase this value, the picture outline becomes stronger and clearer.

Adjust this value appropriately depending on the sharpness of the picture.

* MONITOR : Please change the settings value of video appropriate to your monitor.

- LCD : Please select this menu item when using a LCD monitor.

- CRT : Please select this menu item when using a CRT monitor.

- USER : Please use this menu item when using a monitor other than standard ones. You can

change the gamma, PED level, and color gain in the sub menus.

* RETURN : Select this to save the settings for the IMAGE ADJ menu and to return to the SETUP

menu.

15

USER’S MANUAL

NOTE

■ When the V-REV or H-REV mode is enabled, the text on the screen does not flip.

■ If you increase the SHARPNESS level too high, the picture may become distorted or noise may appear.

◆ CAM TITLE : If you enter a title, the title will appear on the monitor.

1) If the SPECIAL menu screen is displayed, use the Function Setup switch so that the arrow indicates 'CAM TITLE'.

CAMERA TITLE SETUP

2) Set it to 'ON' by using the Function Setup switch.

3) Press the Function Setup switch.

4) Use the Function Setup switch to move to a

A B C D E F G H I J K L M

N O P Q R S T U V W X Y Z a b c d e f g h i j k l m desired letter and select the letter by pressing n o p q r s t u v w x y z the Function Setup switch. Repeat this to enter multiple letters. You can enter up to 15 letters.

- . 0 1 2 3 4 5 6 7 8 9

←→CLR POS END

5) Enter a title, move the cursor to 'POS' and press the Function Setup switch. The entered title appears on the screen. Select the position to display the title on the screen by using the

Function Setup switch and press the Function

Setup switch. When the position is determined, select 'END' and press the Function Setup switch to return to the SPECIAL menu.

SHOP

NOTE

■ When the CAM TITLE menu is ‘OFF’, no title will be displayed on the monitor screen even if you enter one.

■ Only English is available in this mode.

■ If you move the cursor to CLR and press the Function Setup switch, all the letters are deleted. To edit a letter, change the cursor to the bottom left arrow and press the Function

Setup switch. Move the cursor over the letter to be edited, move the cursor to the letter to be inserted and then press the Function Setup switch.

◆ SYNC : In areas where the supply is at 60Hz(NTSC), 50Hz(PAL), you can synchronize the output phase of multiple cameras using the power synchronization function (Line-Lock) without using a synchronization signal generator.

- INT : Internal Synchronization Type

- L/L : Power Synchronization Type, Line-lock

* Press the Function Setup switch.

* You can select a desired phase from 0 to 359 when select 'phase'.

16

USER’S MANUAL

NOTE

■ When using AC power at 60Hz(NTSC), 50Hz(PAL), frequency, you can use the L/L type synchronization.

■ When the power is DC 12V, the SYNC menu is fixed to the ‘INT’ mode.

◆ MOTION DET :This product has a feature that allows you to observe movement of objects in 8 different areas on the screen, and the words

'MOTION DETECTED' appear on the screen when movement is detected.

Activity can be monitor more efficiently.

1) When the SPECIAL menu screen is displayed,

MOTION DET

1.SENSITIVITY

2.AREA MODE

3.SEL POS

4.XPOS

5.YPOS

6.FILL → SET

7.RETRUN

AREA1

ON

L-TOP

3

5 press the Function Setup switch so that the arrow indicates‘MOTION DET’.

2) Set up the mode using the Function Setup switch.

- SENSITIVITY : You can select up to 8 MD areas. When SENSITIVITY number is high, motion detection sensitivity is increased to recognize even small movement.

- AREA MODE : Determines whether to use the MD area selected in SENSITIVITY.

- SEL POS : Determines which of the 4 vertices of each MD area is to be used.

- XPOS : Determines the coordinate of the horizontal axis for SEL POS.

- YPOS : Determines the coordinate of the vertical axis for SEL POS.

-

FILL→SET : Fills in a selected MD area. The color of the area can be selected from brown, orange, blue, cyan, green, yellow, magenta and red.

- RETURN : Select this to save the MOTION DET menu settings and return to the SPECIAL menu.

◆ PRIVACY : Mask an area you want to hide on the screen.

PRIVACY AREA SETUP

1.AREA

2.MODE

3.MASK COLOR

4.MASK TONE

5.TOP

6.BOTTOM

7.LEFT

8.RIGHT

9.RETURN

AREA1

OFF

GREEN

1

39

79

13

52

17

USER’S MANUAL

1) When the SPECIAL menu screen is displayed, press the Function Setup switch so that the arrow indicates 'PRIVACY'.

2) Set up the mode using the Function Setup switch.

- AREA : You can select up to 12 PRIVACY areas.

- MODE : Determines whether to use the area selected in the AREA.

- MASK COLOR : Determine area color. You can select Green, Red, Blue, Black, White, Gray.

- MASK TONE : Adjust the brightness of MASK COLOR.

- TOP/BOTTOM/LEFT/RIGHT :Adjust the size and position of the selected area.

- RETURN : Select this to save the PRIVACY menu settings and return to the SPECIAL menu.

◆ DIS (Digital Image Stabilizer) :

This function mitigates any picture movement due to external factors such as wind.

NOTE

■ As the DIS function uses the digital zoom the camera's resolution will decrease.

■ DIS doesn’t operate when background illumination is too low.

■ DIS doesn’t operate when object pattern is monotonic as like sky or white wall.

◆ LANGUAGE : You can select the menu language according to your requirements.

◆ RETURN : Select this to save the SPECIAL menu settings and return to the MAIN SETUP menu.

Exit Setting

Select a desired EXIT mode using the Function Setup Switch.

- SAVE : Save the current settings and exit the MAIN SETUP menu.

- NOT SAVE : Do not save the current settings and exit the MAIN SETUP menu.

- RESET : Resets the camera settings to the factory defaults. Language, Communication and

Monitor Settings are not initialized.

18

USER’S MANUAL

Trouble Shooting

PROBLEM

Northing appears on the screen.

The image on the screen is dim.

The image on the screen is dark.

The camera is not working properly and the surface of the camera is hot.

Motion Detection is not activated.

POSSIBLE CAUSE

☞Check the power cable, power supply output and video

connection between the camera and monitor.

☞Are the camera lens or the lens glass dirty?

Clean the lens / glass with a soft clean cloth.

☞Adjust the monitor controls, as required.

☞If the camera is facing a very strong light, change

the camera position.

☞Adjust the lens focus.

☞Adjust the contrast control of the monitor.

If there is an intermediate device, correctly set the 75Ω/Hi-z.

☞Check the camera is correctly connected to an appropriate

regulated power source.

☞Has MOTION DET been set to ON in the menu?

Has MD AREA been properly defined?

The color of the picture is not correct.

The image on the screen flickers.

The SENS-UP does not work.

☞Check the settings in WHITE BALANCE menu.

☞Make sure that the camera isn’t facing direct sunlight or fluorescent lighting. If necessary,change the camera position.

Check that the AGC setting in the EXPOSURE menu is’t set to OFF.

Check the EXPOSURE menu and make sure SHUTTER is set to------.

19

USER’S MANUAL

20

▶ MEMO

USER’S MANUAL

21

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

advertisement