advertisement
QUICK LINKS
Contents
Index
Regulatory Compliance
Product Information
Warranty
GETTING STARTED
About the Display
Package Contents
Identify Components
Position Display
Desk Stand Features
INSTALLING THE DISPLAY
Set DIP Switch
Install Display Controller
Connect Video and Power
Install Display Driver
Change Display Properties
Dome CXtra Software
APPENDIXES
Troubleshooting
Specifications
LED Status Lights
Single Desktop
USB Connection
Component Removal
Power Management
Palette Options
Dome
®
C3i Display
DX2 Display Controller
Reference Guide www.planar.com
QUICK LINKS
Contents
Index
Regulatory Compliance
Product Information
Warranty
GETTING STARTED
About the Display
Package Contents
Identify Components
Position Display
Desk Stand Features
INSTALLING THE DISPLAY
Set DIP Switch
Install Display Controller
Connect Video and Power
Install Display Driver
Change Display Properties
Dome CXtra Software
APPENDIXES
Troubleshooting
Specifications
LED Status Lights
Single Desktop
USB Connection
Component Removal
Power Management
Palette Options
Copyright © 2005 Planar Systems, Inc. All rights reserved.
Information in this document has been carefully checked for accuracy; however, no guarantee is given to the correctness of the contents. This document is subject to change without notice. Planar provides this information as reference only. Reference to other vendors’ product does not imply any recommendation or endorsement.
This document contains proprietary information protected by copyright. No part of this manual may be reproduced by any mechanical, electronic, or other means, in any form, without prior written permission of the manufacturer.
Planar, Dome, C3i, CXtra, and RightLight are either registered trademark or trademarks of
Planar Systems, Inc. All other trademarks are the property of their respective owners.
020-0331-03 A
Dome C3i Display
America Sales
Planar Systems, Inc.
1195 NW Compton Drive
Beaverton, OR 97006-1992 USA
(503) 748-1100 phone
(503) 748-1493 fax
Medical Sales
Planar Systems, Inc.
400 Fifth Avenue
Waltham, MA 02451-8738 USA
(781) 895-1155 phone
(781) 895-1133 fax
Europe & Asia-Pacific Sales
European Representative
Planar Systems, Inc.
Olarinluoma 9, P. O. Box 46
FIN-02201 Espoo, Finland
+ 358 9 420 01 phone
+ 358 9 420 0200 fax [email protected]
www.planar.com
ii
QUICK LINKS
Contents
Index
Regulatory Compliance
Product Information
Warranty
GETTING STARTED
About the Display
Package Contents
Identify Components
Position Display
Desk Stand Features
INSTALLING THE DISPLAY
Set DIP Switch
Install Display Controller
Connect Video and Power
Install Display Driver
Change Display Properties
Dome CXtra Software
APPENDIXES
Troubleshooting
Specifications
LED Status Lights
Single Desktop
USB Connection
Component Removal
Power Management
Palette Options
Contents
Regulatory Compliance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv
Product Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix
About the Dome C3i Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Identify the Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Position the Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Desk Stand Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Set the DIP Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Install the Display Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Connect Video Cable and Power Supply . . . . . . . . . . . . . . . . . . . . . . . 9
Install the Display Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Change the Display Properties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Enhancements with Dome CXtra Software . . . . . . . . . . . . . . . . . . . . 13
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
C3i Display Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
LED Status Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Single Desktop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
USB Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Display Driver and Controller Removal . . . . . . . . . . . . . . . . . . . . . . . 27
Power Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Palette Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Overview of Standard Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Dome C3i Display iii
QUICK LINKS
Contents
Index
Regulatory Compliance
Product Information
Warranty
GETTING STARTED
About the Display
Package Contents
Identify Components
Position Display
Desk Stand Features
INSTALLING THE DISPLAY
Set DIP Switch
Install Display Controller
Connect Video and Power
Install Display Driver
Change Display Properties
Dome CXtra Software
APPENDIXES
Troubleshooting
Specifications
LED Status Lights
Single Desktop
USB Connection
Component Removal
Power Management
Palette Options
Regulatory Compliance
United States/European Union/Canada
These displays have been tested and found to comply with IEC/EN 60601-1 and
IEC EN 60601-1-2 standards, and is certified to meet medical standard C22.2
No. 601.1-M1990 (C US Mark).
The medical displays, in addition to meeting medical requirements, has been tested and found to comply with the limits for Federal Communications Commission (FCC) Class B computing devices in a typically configured system since many medical offices are located in residential areas.
It is the system integrator’s responsibility to test and ensure that the entire system complies with applicable electromagnetic compatibility (EMC) laws.
Planar Systems, Inc. has made great efforts to support the medical device industry, in particular, medical device manufacturers and medical device system integrators. We offer state-of-the-art color displays that are compliant with worldwide accepted medical device safety standards, and for the European market, CE-marked displays based on compliance with counsel directive 93/42/EEC— commonly referred to as the Medical Device Directive (MDD). The following summarizes our qualification of these displays as it relates to compliance with the MDD.
The European Medical Device Directive requires that the intended use of the device be defined. The intended use of these displays is “to display alphanumeric, graphic, and image data as inputted from any type of medical device.” These displays do not provide a measurement function in any way, and it is the device and systems manufacturer’s responsibility to verify its function in the integrated device or system.
The displays were classified as required by the MDD according to Annex IX of the directive and the medical device (MEDDEV) guidance available at the time of classification. Because the display uses electrical energy and has no direct patient connections and—by itself—no medical utility, the display is classified according to Rule 12 as an MDD Class I device, component, or accessory. The mode of operation is continuous. The MDD states that manufacturers of Class I medical devices or accessories shall satisfy the requirements in regard to design and manufacturing controls, that is, the applicable assessment route to be used for CE-marking under the MDD, and it shall carry the
CE mark according to Annex XII of the directive, with no notified body annotation.
The applicable safety standards for an MDD Class I display are IEC/EN 60601-1:1990 along with
Amendments 1 and 2. To help the medical device designer evaluate the suitability of these displays,
Planar has also conducted EMC testing to IEC 60601-1-2 as it can be applied. The display with its
Dome C3i Display iv
QUICK LINKS
Contents
Index
Regulatory Compliance
Product Information
Warranty
GETTING STARTED
About the Display
Package Contents
Identify Components
Position Display
Desk Stand Features
INSTALLING THE DISPLAY
Set DIP Switch
Install Display Controller
Connect Video and Power
Install Display Driver
Change Display Properties
Dome CXtra Software
APPENDIXES
Troubleshooting
Specifications
LED Status Lights
Single Desktop
USB Connection
Component Removal
Power Management
Palette Options power supply alone does not represent a functional medical device. Hence, Planar configured a minimal operating system to exercise the display. The resulting data are made available to interested parties.
Equipment used outside Canada and the United States may be provided with a non-certified cord, provided the cord is acceptable to the authorities in the country of usage. Such cords have not been investigated by CSA and UL and are not part of the certification.
For 120 volt applications, use only a UL-listed detachable power cord with NEMA configuration
5-15P type (parallel blades) plug cap. For 240 volt applications, use only a UL-listed detachable power supply cord with NEMA configuration 6-15P type (tandem blades) plug cap.
This is informative data, not certification data. Certification data must be obtained by the device or system integrator according to Article 12 of the MDD titled “Particular procedure for systems and procedure packs.” Paragraph 2 clearly outlines the device or system integrator’s responsibility in this matter.
In summary, Planar Systems, Inc. is CE-marking these displays under the Medical Device Directive, which establishes compliance to the basic medical safety standards. However, EMC compliance can only be accomplished in the configured medical device or system and is the responsibility of the device or system manufacturer. Planar has the necessary documentation such as IEC 60601-1 notified body and other third-party test reports and certifications, a risk/hazard analysis, an essential requirements checklist, and the Planar International Electrotechnical Commission (IEC) declaration of conformity.
Planar Systems, Inc., located in Beaverton, Oregon, USA, is the manufacturer of these displays in the meaning of the directive. As required by the MDD in Article 14, Planar Systems, Inc., not residing in the European Economic Area (EEA), has a European representative, Planar Systems, Inc.—
Olarinluoma 9, P. O. Box 46, FIN-02201 Espoo, Finland (phone + 358 9 420 01; fax + 358 9 420 0200).
In the opinion of Planar Systems, Inc. registration required to put this device into commerce is the responsibility of the medical device/system manufacturer, and Planar supports this requirement by providing a European Commission (EC) declaration of conformity. If Planar supplies a display to an end user, rather than a device manufacturer, it is the end user’s responsibility to ensure continued compliance with the MDD of the system in which the display is integrated.
For vigilance reporting as required under Article 10 of the MDD, Planar Systems, Inc. will provide any information requested by competent authority to support any reported incident investigation by such an authority.
Dome C3i Display v
QUICK LINKS
Contents
Index
Regulatory Compliance
Product Information
Warranty
GETTING STARTED
About the Display
Package Contents
Identify Components
Position Display
Desk Stand Features
INSTALLING THE DISPLAY
Set DIP Switch
Install Display Controller
Connect Video and Power
Install Display Driver
Change Display Properties
Dome CXtra Software
APPENDIXES
Troubleshooting
Specifications
LED Status Lights
Single Desktop
USB Connection
Component Removal
Power Management
Palette Options
FCC Compliance Statement
•
•
•
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technical for help.
Caution: Changes or modifications to this equipment not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Dome C3i Display vi
QUICK LINKS
Contents
Index
Regulatory Compliance
Product Information
Warranty
GETTING STARTED
About the Display
Package Contents
Identify Components
Position Display
Desk Stand Features
INSTALLING THE DISPLAY
Set DIP Switch
Install Display Controller
Connect Video and Power
Install Display Driver
Change Display Properties
Dome CXtra Software
APPENDIXES
Troubleshooting
Specifications
LED Status Lights
Single Desktop
USB Connection
Component Removal
Power Management
Palette Options
European Union Declaration of Conformity for Medical Application
A Declaration of Conformity has been filed for this product. For additional copies of the Declaration of Conformity document, contact Planar Systems, Inc.
The Dome C3i digital flat-panel display meets the essential health and safety requirements, is in conformity with, and the CE marking has been applied according to the relevant
EU Directives listed below, using the relevant section of the following EU standards and other normative documents;
EU EMC Directive 89/336/EEC
EU Electromagnetic Compatibility Directive
EN 60601-1-2 (2001) Medical
Electrical Equipment
EN 55011 (Class B)
Section 1.2. Collateral standard electromagnetic compatibility requirements
Limits and methods of measurements for radio interference characteristics of industrial, scientific, and medical equipment
IEC 1000-3-2
IEC 1000-3-3
IEC 1000-4-2
IEC 1000-4-3
IEC 1000-4-4
Harmonic emissions
Voltage fluctuations/flicker emissions
Electrostatic discharge requirements for industrial process measurement and control equipment
Radiated electromagnetic field requirements for industrial process measurement and control equipment
Electrically fast transients for industrial process measurement and control equipment
IEC 1000-4-5
IEC 1000-4-11
IEC 1000-4-6
IEC 1000-4-8
Surge requirements
Voltage variations/dips/interrupts
Conducted immunity
Magnetic field immunity
Conformance to the Medical Device Directive 93/42/EEC
EN 60601-1 Medical
Electrical Equipment
Part 1: General requirements for safety
Dome C3i Display vii
QUICK LINKS
Contents
Index
Regulatory Compliance
Product Information
Warranty
GETTING STARTED
About the Display
Package Contents
Identify Components
Position Display
Desk Stand Features
INSTALLING THE DISPLAY
Set DIP Switch
Install Display Controller
Connect Video and Power
Install Display Driver
Change Display Properties
Dome CXtra Software
APPENDIXES
Troubleshooting
Specifications
LED Status Lights
Single Desktop
USB Connection
Component Removal
Power Management
Palette Options
Australian
C-Tick
Japan
VCCI
Australian Communications Authority regulating product EMC compliance.
China
CCC
GB4943-2001
GB9254-1998 (Class A)
CB17625.1-2003
China Compulsory Certification regulating safety and EMC.
Voluntary Control Council for Interference by information technology equipment sold in Japan.
Korea
MIC Mark Ministry of Information and Communications.
Dome C3i Display viii
QUICK LINKS
Contents
Index
Regulatory Compliance
Product Information
Warranty
GETTING STARTED
About the Display
Package Contents
Identify Components
Position Display
Desk Stand Features
INSTALLING THE DISPLAY
Set DIP Switch
Install Display Controller
Connect Video and Power
Install Display Driver
Change Display Properties
Dome CXtra Software
APPENDIXES
Troubleshooting
Specifications
LED Status Lights
Single Desktop
USB Connection
Component Removal
Power Management
Palette Options
Product Information
The design of the Dome C3i digital display takes into account every known measure to ensure your personal safety. Improper use of the display can result in electric shock, fire, or damage to the display. Read all instructions before setting up the display.
Important recycle information:
LCD lamp(s) inside this product contain mercury. This product may contain other electronic waste that can be hazardous if not disposed of properly.
Recycle or dispose in accordance with local, state, or federal laws. For more information, contact the Electronic Industries Alliance at WWW.EIAE.ORG.
For lamp-specifc disposal information, check WWW.LAMPRECYCLE.ORG.
Symbol explanations
Disposal – Do not use household or municipal waste collection services for disposal of electrical and electronic equipment. EU countries require the use of separate recycling collection services. Contact local authorities for more information on proper disposal.
Caution – Section contains important information. Read the accompanying text carefully, for proper operation and maintenance of the display system
Dangerous voltage – Section contains important precautions about electric shock.
Read the accompanying text carefully, to prevent damage to components of the display system and for your safety.
Barometric pressure – Transport and storage
12,000 meters (39,400 feet), maximum in unpressurized container
Relative humidity – Transport and storage
5% to 90% (non-condensing)
Temperature – Transport and storage
-10° to 60° C
Dome C3i Display ix
QUICK LINKS
Contents
Index
Regulatory Compliance
Product Information
Warranty
GETTING STARTED
About the Display
Package Contents
Identify Components
Position Display
Desk Stand Features
INSTALLING THE DISPLAY
Set DIP Switch
Install Display Controller
Connect Video and Power
Install Display Driver
Change Display Properties
Dome CXtra Software
APPENDIXES
Troubleshooting
Specifications
LED Status Lights
Single Desktop
USB Connection
Component Removal
Power Management
Palette Options
Intended use
The Dome C3i display is an AMLCD display designed for viewing medical X-ray images.
This unit is not used near patients and is outside of 1.83 m perimeter and 2.29 m vertical.
Safety precautions
External equipment intended for connection to signal input, signal output, or other connectors, must comply with the relevant IEC standard (EN/IEC 60601-1 series for medical electrical equipment). In addition, all such combinations (systems) must comply with the standard IEC 60601-1-1, Safety requirements for medical electrical systems . Equipment not complying to IEC 60601 must be kept outside the patient environment, as defined in the standard as at least 1.5 meters from the patient or the patient support.
Any person who connects external equipment to signal input, signal output, or other connectors has formed a system and is therefore responsible for the system to comply with the requirements of IEC 60601-1-1. If in doubt, speak with a qualified technician.
•
•
To prevent fire or injury
•
•
•
Replace the power supply or cables if damaged.
Use only the appropriate power source indicated in this guide or listed on the display.
•
Activate the Dome CXtra Backlight Saver service (the preferred method) or the DPMS
(Display Power Management Signaling) energy saver when the display is idle for extended periods.
Do not plug the power supply into an overloaded AC outlet or extension cord.
Overloaded AC outlets and cords can result in electric shock or fire.
• Do not drop or push objects into the display case. Internal components contain high voltage.
Unplug the power cord from the wall outlet during thunderstorms.
Do not place magnetic devices, such as magnets or motors, near the display.
Dome C3i Display
Safety tips
• Never open the Dome C3i display case, even when the power is off.
Dangerous voltage inside may cause electric shock or death.
• To avoid damage to the Dome C3i display, use the grounded power supply and video cable supplied by Planar, or use certified replacements.
• Be sure the Dome C3i display is electrically grounded. You must connect the third grounding pin on the US power cord to a grounded outlet. The European power cord does not have a third grounding pin, but it still must be plugged into a grounded outlet.
•
•
If you cannot insert the plug into the outlet you plan to use, have a licensed electrician replace the outlet with a properly grounded outlet. If your power cord connects directly into the computer, make sure the computer is grounded.
Take appropriate measures to keep the Dome C3i display dry if it is part of a surgical system. The Dome C3i display lacks protection against liquids or spills.
x
QUICK LINKS
Contents
Index
Regulatory Compliance
Product Information
Warranty
GETTING STARTED
About the Display
Package Contents
Identify Components
Position Display
Desk Stand Features
INSTALLING THE DISPLAY
Set DIP Switch
Install Display Controller
Connect Video and Power
Install Display Driver
Change Display Properties
Dome CXtra Software
APPENDIXES
Troubleshooting
Specifications
LED Status Lights
Single Desktop
USB Connection
Component Removal
Power Management
Palette Options
•
•
•
•
•
•
•
•
•
To set up the display properly
•
•
Allow the display to warm up to room temperature before turning it on.
Avoid sudden temperature changes. Sudden changes may cause condensation that can damage the display.
Turn off your computer, but leave it plugged into a grounded outlet.
Secure the display properly onto a standard VESA 100-mm mounting unit if you elect not to use the desk stand.
Do not step on or place anything on top of the power cord.
Do not set up the display near strong light sources.
Do not block the vents on the back of the display or install the display in a built-in enclosure. Blocked vents cause excessive heat to build up inside the display, increasing risk of fire.
Do not expose the display to water or excessive moisture.
Do not place the display near a heat source.
Do not hang anything from the display.
Use the display only in an indoor setting.
To disconnect the power supply properly
First, turn off your computer and other connected devices. Then unplug the power supply from the display or wall outlet.
Dome C3i Display
Reasons to disconnect power
• Power cord is damaged.
• Liquid spills inside the display case.
• Display is dropped or case is damaged.
• Display needs service or repair.
• Display or case needs cleaning.
xi
QUICK LINKS
Contents
Index
Regulatory Compliance
Product Information
Warranty
GETTING STARTED
About the Display
Package Contents
Identify Components
Position Display
Desk Stand Features
INSTALLING THE DISPLAY
Set DIP Switch
Install Display Controller
Connect Video and Power
Install Display Driver
Change Display Properties
Dome CXtra Software
APPENDIXES
Troubleshooting
Specifications
LED Status Lights
Single Desktop
USB Connection
Component Removal
Power Management
Palette Options
To clean the LCD screen
3
4
1
2
Unplug the power supply.
Dampen a clean, soft nonabrasive cloth with isopropyl alcohol.
Wipe the screen gently .
Dry the screen with a clean, soft nonabrasive cloth to remove any residue.
Shipping/storing the display
Keep the display in its shipping container until installation. Return the display to its original container whenever you need to store the unit, move it to another location, or return it for repair. The packaging supplied by the manufacturer protects the display from damage while it is in transit. Also see environment specifications for detailed information.
Before returning the display to the container for shipping or storing, do the following:
•
•
•
Swivel the display panel in portrait mode.
Push the panel down to the lowest position.
Use the stand lock to anchor the panel.
Disposal information
Follow your local governing ordinance and recycling policy for proper disposal or recycling of display components.
Dome C3i Display
Maintenance tips
• Use a clean, lint-free, absorbent cotton cloth to clear off any residual glue from removal of the protective film.
• Use a clean, lint-free, absorbent cotton cloth to remove surface dust. Apply light pressure to remove the dust.
• Dampen a clean cloth with a small amount of isopropyl alcohol to remove glue or dust if the screen is still not clean. Use a clean, dry cloth to completely remove the alcohol residue.
• Do not use chemically treated dust cloths on the display case or
LCD screen.
• Do not use acetone, toluene, or harsh solvents. They can damage the polarizer and display case.
• Do not saturate the cleaning cloth with alcohol. The alcohol may seep into the display case and collect in the enclosure.
• Do not allow water or other stains to stand on the unit.
Wipe these off immediately to prevent damage to the display case and screen.
xii
QUICK LINKS
Contents
Index
Regulatory Compliance
Product Information
Warranty
GETTING STARTED
About the Display
Package Contents
Identify Components
Position Display
Desk Stand Features
INSTALLING THE DISPLAY
Set DIP Switch
Install Display Controller
Connect Video and Power
Install Display Driver
Change Display Properties
Dome CXtra Software
APPENDIXES
Troubleshooting
Specifications
LED Status Lights
Single Desktop
USB Connection
Component Removal
Power Management
Palette Options
About the Dome C3i Display
The Dome C3i display system, 3 megapixels, consists of a thin film transistor, LCD panel and the DX2 controller and driver. The display’s thin film transistors, in a transmissive-type display, use an integrated cold cathode fluorescent tube (CCFT) backlight system.
The display is designed for grayscale medical imaging in diagnostic settings, in either portrait or landscape orientation. It comes fully tuned with gamma correction that complies with the DICOM Part 14 Standard. An all-digital design enables the display to produce the sharp, crisp images critical to softcopy medical viewing.
Unwanted analog display image artifacts, such as noise, jitter, ghosting, and image smearing are eliminated.
The Dome C3i display offers the following key features. See the specification for more information.
• 3061 distinct shades of gray
• IPS LCD technology for distortion-free image over a wide-viewing angle
• Accelerated hardware rotation for viewing in portrait or landscape mode
• Calibrated to DICOM response curve
• Automated calibration and backlight stabilization through RightLight technology
The Dome CXtra™ software enhances the functionality of the Dome C3i display.
Dome CXtra provides a range of value-added services, such as DICOM calibration, error reporting, and backlight saver.
Before installing the display system, review the safety and installation precautions . Once your display system is in operation, follow the guidelines for cleaning and servicing your unit. Also see environment specifications for detailed operating and storage information.
Dome C3i Display
Systems requirements
Computer system
1 PCI slot per board
50 MB hard disk space
256 MB RAM
CD-ROM drive
Operating system
Windows XP or Windows 2000
Dome C3i display
Size (diagonal) 528 mm (20.8 in)
Resolution 1536 x 2048 pixels
1
QUICK LINKS
Contents
Index
Regulatory Compliance
Product Information
Warranty
GETTING STARTED
About the Display
Package Contents
Identify Components
Position Display
Desk Stand Features
INSTALLING THE DISPLAY
Set DIP Switch
Install Display Controller
Connect Video and Power
Install Display Driver
Change Display Properties
Dome CXtra Software
APPENDIXES
Troubleshooting
Specifications
LED Status Lights
Single Desktop
USB Connection
Component Removal
Power Management
Palette Options
Package Contents
The Dome C3i display system contains the items shown here. Speak with your sales rep if any item is missing or damaged.
Dome C3i Display
Display controller
DVI video cable
DC power adapter
Dome C3i LCD panel mounted on desk stand
AC power cord
CD-ROMs with display driver and
Dome CXtra software
Quick references for Dome
CX display and
Dome CXtra software
Unpacking and handling tips
The Dome C3i display is a precision instrument that requires proper care to maintain product operation and adherence to specification.
Unpack the display and components carefully. Improper handling may damage or break the LCD glass.
• Use both hands to grasp the display case when lifting it from the shipping carton, but avoid touching the screen.
• Do not touch the polarizer with foreign objects.
• Do not touch the polarizer with bare fingers. Some cosmetics are detrimental to the polarizer, and skin oils are difficult to remove.
• Avoid sudden temperature change as this may cause condensation, which damages the display.
• Do not subject the unit to strong light sources.
• Do not remove the back cover or disassemble the display. There are no user-serviceable parts inside.
2
QUICK LINKS
Contents
Index
Regulatory Compliance
Product Information
Warranty
GETTING STARTED
About the Display
Package Contents
Identify Components
Position Display
Desk Stand Features
INSTALLING THE DISPLAY
Set DIP Switch
Install Display Controller
Connect Video and Power
Install Display Driver
Change Display Properties
Dome CXtra Software
APPENDIXES
Troubleshooting
Specifications
LED Status Lights
Single Desktop
USB Connection
Component Removal
Power Management
Palette Options
Identify the Components
Review this illustration of the back panel to identify controls and ports on the display unit.
1 2
Dome C3i Display
3 4
Back panel of the Dome C3i display
Dome C3i connector plate
Controls and connector ports
Read the plates from left to right.
Dome C3i
1 Reset button (Restores the original display configuration.)
2 LED status lights. Provides information about the status of the display. See page 21 .
3 DVI connector (Drives the data to the display.)
4 8-pin DIN power connector
(Drives power to the display.)
3
QUICK LINKS
Contents
Index
Regulatory Compliance
Product Information
Warranty
GETTING STARTED
About the Display
Package Contents
Identify Components
Position Display
Desk Stand Features
INSTALLING THE DISPLAY
Set DIP Switch
Install Display Controller
Connect Video and Power
Install Display Driver
Change Display Properties
Dome CXtra Software
APPENDIXES
Troubleshooting
Specifications
LED Status Lights
Single Desktop
USB Connection
Component Removal
Power Management
Palette Options
Position the Display
You can adjust the tilt, height, viewing angle, and orientation of the display to maintain an ergonomic and comfortable viewing position. Before you unpack the display, select a suitable workspace for the display. You need a stable, level, and clean surface near a wall outlet.
Tilt range
Adjust the tilt angle of the display so that the screen faces slightly downward from your angle of view.
Height range
Unfasten the stand lock at the top of the desk stand (slide it to the left) then raise or lower the panel to adjust the height.
Your eyes should be level with the top of the display cabinet so that you look downward to read the screen contents.
Dome C3i Display 4
QUICK LINKS
Contents
Index
Regulatory Compliance
Product Information
Warranty
GETTING STARTED
About the Display
Package Contents
Identify Components
Position Display
Desk Stand Features
INSTALLING THE DISPLAY
Set DIP Switch
Install Display Controller
Connect Video and Power
Install Display Driver
Change Display Properties
Dome CXtra Software
APPENDIXES
Troubleshooting
Specifications
LED Status Lights
Single Desktop
USB Connection
Component Removal
Power Management
Palette Options
Viewing angle
Swivel the display panel from side to side to adjust the viewing angle.
Dome C3i Display
Orientation mode
Use both hands to turn the display 90 degrees clockwise to rotate the display between portrait and landscape modes.
5
QUICK LINKS
Contents
Index
Regulatory Compliance
Product Information
Warranty
GETTING STARTED
About the Display
Package Contents
Identify Components
Position Display
Desk Stand Features
INSTALLING THE DISPLAY
Set DIP Switch
Install Display Controller
Connect Video and Power
Install Display Driver
Change Display Properties
Dome CXtra Software
APPENDIXES
Troubleshooting
Specifications
LED Status Lights
Single Desktop
USB Connection
Component Removal
Power Management
Palette Options
Desk Stand Features
Unfasten the stand lock to adjust display height . Remove the stand cover to thread the power cord and DVI cable connections to the display. To activate the USB hub function, the display must be connected to a USB-compliant computer or another hub with
a USB cable. Even if the display is in power-saving mode, the USB devices function when they are connected to the USB ports
(both upstream and downstream) of the display.
Stand lock
Move the stand lock lever to the left to adjust the height of the display.
Stand cover release
Press the PUSH button at the bottom of the desk stand and pull the stand cover down and out to remove it.
USB hub
Use the integrated, self-powered
USB hub to attach USB devices to the display rather than to the computer.
Dome C3i Display 6
QUICK LINKS
Contents
Index
Regulatory Compliance
Product Information
Warranty
GETTING STARTED
About the Display
Package Contents
Identify Components
Position Display
Desk Stand Features
INSTALLING THE DISPLAY
Set DIP Switch
Install Display Controller
Connect Video and Power
Install Display Driver
Change Display Properties
Dome CXtra Software
APPENDIXES
Troubleshooting
Specifications
LED Status Lights
Single Desktop
USB Connection
Component Removal
Power Management
Palette Options
Set the DIP Switch
For DX2 display controller, slide switch 1 on DIP switch S2 into the ON position to enable VGA mode. Enable VGA on only one (1) board when you install multiple boards, Disable VGA on all boards if you are using a separate VGA card.
For some Dell systems, you may need to enable VESA modes in order to see output on the screen during the boot process. If so, slide switch 2 on DIP switch S2 into the
ON position.
Dome C3i Display
Upper left, DIP switch S2 on the DX2 display controller
Switch settings
For single desktop mode, slide switch 3 into the ON position.
For default landscape mode, slide switch 4 into the ON position.
Warning
If you leave the computer turned on, you could get an electric shock and cause damage to the system components.
Remove the display controller slowly from its package and staticshielding bag to prevent an electrostatic discharge.
Static electricity can damage the controller. When touching the board or parts of the motherboard, take these precautions:
• Wear an antistatic wrist strap.
• Discharge your body’s static electricity repeatedly by touching the power supply or the metal surface of the computer chassis.
7
QUICK LINKS
Contents
Index
Regulatory Compliance
Product Information
Warranty
GETTING STARTED
About the Display
Package Contents
Identify Components
Position Display
Desk Stand Features
INSTALLING THE DISPLAY
Set DIP Switch
Install Display Controller
Connect Video and Power
Install Display Driver
Change Display Properties
Dome CXtra Software
APPENDIXES
Troubleshooting
Specifications
LED Status Lights
Single Desktop
USB Connection
Component Removal
Power Management
Palette Options
Install the Display Controller
Before you begin, choose a well-ventilated location with an adequate amount of space. Excessive heat cannot dissipate when display vents are blocked. Make sure a grounded AC outlet is within easy reach.
When installing multiple display controllers, install all boards before you install the display driver.
Turn your computer off. Leave the power cord plugged into the grounded outlet.
To install the display controller
1 Remove the blank bracket from an available PCI slot.
Dome C3i Display
2 Insert the display controller into the slot, align the connector pins, and press the board down until it is firmly seated. Secure the mounting bracket.
8
QUICK LINKS
Contents
Index
Regulatory Compliance
Product Information
Warranty
GETTING STARTED
About the Display
Package Contents
Identify Components
Position Display
Desk Stand Features
INSTALLING THE DISPLAY
Set DIP Switch
Install Display Controller
Connect Video and Power
Install Display Driver
Change Display Properties
Dome CXtra Software
APPENDIXES
Troubleshooting
Specifications
LED Status Lights
Single Desktop
USB Connection
Component Removal
Power Management
Palette Options
Connect Video Cable and Power Supply
Turn your computer off. Leave the power cord plugged into the grounded outlet.
Use only the video cables and the universal external 12V DC power supply shipped with the Dome C3i display. Use power supply Ault MW122RA1223F52. Secure all the connections you make.
To connect the display
1 Plug one end of the DVI cable into the DVI port on the connector plate.
2 Plug the power cord into the power input port on the connector plate.
3 Plug the other end of the DVI cable into the Video 1 port on the installed display controller.
4 Plug the other end of the power cord into the power supply.
5 Plug the power supply cord into a grounded AC outlet.
Connections for the Dome C3i display
Dome C3i Display
Connection to the DX2 board for a single display
Installation tips
Easy access to ports
For displays mounted on a desk stand, rotate the LCD panel from portrait to landscape for easy access to the ports.
Threading cables
Thread the DVI cable and power cord through the back of the stand.
Make sure the cable and cord run through the notches. To reattach the stand cover, align the hooks with the slots on the stand. Press the cover into place. A click sound signals a secure connection.
Restarting
Turn on your display before you turn on your computer. Failing to do so could damage the display.
Multiple displays
Connect the first display of a twoheaded system, or the only display of a one-headed system, to the
Video 1 port. Connect all displays to the display controller before you turn on the computer system to install the driver. The driver can then detect all displays.
Using two displays allows you to view two images simultaneously or one image across both displays.
9
QUICK LINKS
Contents
Index
Regulatory Compliance
Product Information
Warranty
GETTING STARTED
About the Display
Package Contents
Identify Components
Position Display
Desk Stand Features
INSTALLING THE DISPLAY
Set DIP Switch
Install Display Controller
Connect Video and Power
Install Display Driver
Change Display Properties
Dome CXtra Software
APPENDIXES
Troubleshooting
Specifications
LED Status Lights
Single Desktop
USB Connection
Component Removal
Power Management
Palette Options
Install the Display Driver
Before you install the driver, remove any previously installed display driver for the
DX2 display controller from your computer system. Follow the procedure shown in the sidebar.
Use the following procedures to install the display driver on Windows XP and
Windows 2000 systems.
To install the driver
1 Log on with administrator privileges. The InstallShield Wizard reports new hardware.
2 Click Cancel. You must run Setup.exe to install the driver.
3 Insert the W2KDXPCI CD and open the CD folder.
4 Double-click Setup.exe.
5 Click Next to proceed through the installation and start copying files.
6 For each display you install, click Yes if the Digital Signature Not Found dialog appears. (On Windows XP systems, the Hardware Installation dialog is equivalent. Click Continue Anyway to proceed.)
7 Select Yes, I want to restart my computer now, and click Finish.
To enable the display
1 Log on with administrator privileges.
2 Right-click the desktop. Select Properties > Settings.
3 Select the display icon.
4 Select Extend my Windows desktop onto this monitor. Click Apply.
5 Click OK.
Dome C3i Display
Removing an existing driver
If necessary, uninstall the 63-WINDX driver before you install the
63-W2KDXPCI driver.
To remove the 63-WINDX driver
1 Log on with administrator privileges.
2 Insert the WINDX CD and open the CD folder.
3 Browse to the Win2k\DXpci directory.
4 Double-click Setup.exe.
5 Select Remove and click Next.
6 Click OK to confirm uninstall.
7 Select Yes, I want to restart my computer now, and click Finish.
10
QUICK LINKS
Contents
Index
Regulatory Compliance
Product Information
Warranty
GETTING STARTED
About the Display
Package Contents
Identify Components
Position Display
Desk Stand Features
INSTALLING THE DISPLAY
Set DIP Switch
Install Display Controller
Connect Video and Power
Install Display Driver
Change Display Properties
Dome CXtra Software
APPENDIXES
Troubleshooting
Specifications
LED Status Lights
Single Desktop
USB Connection
Component Removal
Power Management
Palette Options
Change the Display Properties
You can change the display properties, such as resolution, palette options, and brightness, using the Dome tab after the Dome C3i display is attached to the
Windows desktop. Otherwise, use Properties > Settings tab.
To determine screen assignments
Click Identify in the Settings tab to match screens to display controllers.
To set the resolution and palette
Use the Resolution field on the Dome tab to set the resolution to portrait or landscape mode.
1 Log on with administrator privileges.
2 Right-click the desktop. Select Properties > Settings.
3 Select Default Monitor and Dome DX/DX2 Properties from the Display list.
4 Check the selection box for Extend my Windows desktop onto this monitor.
5 Select Advanced > Dome.
6 Choose a resolution and palette option. Click Apply.
7 Click OK until you return to the desktop.
For more information on palette options, see “Palette Options” on page 29 .
To set brightness
In the Brightness field of the DOME tab, slide the scroll box left or right, or use
the left and right arrows, to set brightness for each flat panel. (The default brightness is 100%.) Click OK.
Dome C3i Display
Screen assignments
Windows 2000 renumbers and reassigns screens as you add them to the configuration. Set resolutions or preferences only after all display controller and screens are installed.
Restart your system to make sure the screen assignments are retained.
Resolutions and palettes
Set display properties on the Dome
C3i display using the resolutions and palette options on page 19 . Note that single desktop requires a dualdisplay system.
11
QUICK LINKS
Contents
Index
Regulatory Compliance
Product Information
Warranty
GETTING STARTED
About the Display
Package Contents
Identify Components
Position Display
Desk Stand Features
INSTALLING THE DISPLAY
Set DIP Switch
Install Display Controller
Connect Video and Power
Install Display Driver
Change Display Properties
Dome CXtra Software
APPENDIXES
Troubleshooting
Specifications
LED Status Lights
Single Desktop
USB Connection
Component Removal
Power Management
Palette Options
To set driver options
Beware that the Disable DirectDraw driver option has specific conditions which may affect your display.
The Mirror option allows you to view the display with a mirror.
The NTSC 32->8 option, when enabled, converts color to grayscale in accordance with the NTSC standard. However, in some configurations, you may see artifacts on the screen after a popup window is closed.
In the Driver Options field of the Dome tab, select Disable DirectDraw.
Click Apply or OK.
To get information
Information about the flat panel, display controller, and driver appears on the lower half of the Dome tab, as shown here.
Panel information includes panel type, serial number, backlight usage, and onboard temperature (in degrees Celsius). The temperature reading of a panel is given when you first open the panel and if you later select it. The revision numbers of the firmware and microcontrollers are also included. General information includes display controller type, driver version, and library version.
Dome C3i Display 12
QUICK LINKS
Contents
Index
Regulatory Compliance
Product Information
Warranty
GETTING STARTED
About the Display
Package Contents
Identify Components
Position Display
Desk Stand Features
INSTALLING THE DISPLAY
Set DIP Switch
Install Display Controller
Connect Video and Power
Install Display Driver
Change Display Properties
Dome CXtra Software
APPENDIXES
Troubleshooting
Specifications
LED Status Lights
Single Desktop
USB Connection
Component Removal
Power Management
Palette Options
Enhancements with Dome CXtra Software
The Dome CXtra™ software enhances the functionality of the Dome C3i display for viewing medical images in diagnostic settings.
The advantages of Dome CXtra includes consistent grayscale presentation of images, as a result of conformance with the DICOM Grayscale Standard display function. Specifically, the Dome C3i display is fully calibrated to the DICOM response curve. It uses an embedded RightLight™ sensor to provide continuous luminance stability, guaranteeing consistent image quality and adherence to DICOM standards.
This sensor works with the digital interface board that is built into the back of the Dome C3i display.
Dome CXtra services allow you to monitor and stabilize display backlights, schedule the backlight saver, and retrieve information on CXtra events and errors conditions.
You can also run display acceptance tests, including the recommendations of the
American Association of Physicists in Medicine Task Group 18 and the DIN test standards. You can also monitor and maintain your Dome C3i display locally or from a remote location using any SNMP console application.
For more information, visit www.planar.com
.
Dome C3i Display
CXtra Services
• Reporting – Access service info, view events and history, and check events related to error conditions.
• RightLight – Stabilize display backlights and maintain DICOM conformance and desired white level across displays.
• Backlight saver – Schedule sleep for the display backlights.
• Privilege – Limit users who can change display parameters.
• AAPM TG18 test – Use AAPM TG 18 recommendations to test displays.
• DIN acceptance and constancy –
Perform the German standard test to measure display performance.
• Test patterns – View test patterns that show the display image quality.
• Enterprise management – Manage displays remotely using any SNMP console application, or locally.
13
QUICK LINKS
Contents
Index
Regulatory Compliance
Product Information
Warranty
GETTING STARTED
About the Display
Package Contents
Identify Components
Position Display
Desk Stand Features
INSTALLING THE DISPLAY
Set DIP Switch
Install Display Controller
Connect Video and Power
Install Display Driver
Change Display Properties
Dome CXtra Software
APPENDIXES
Troubleshooting
Specifications
LED Status Lights
Single Desktop
USB Connection
Component Removal
Power Management
Palette Options
Troubleshooting
Problem
No image appears on
the screen
Possible cause
Computer is not powered on.
Power cord is not securely connected.
Video cable connected incorrectly.
Power LED is amber Display is in DPMS mode.
No active signal coming from computer.
Signal cable is not fastened securely.
Computer video signal is not VESA DPMS standard.
“Check video cable” message Video cable is not securely fastened.
Solution
Turn on computer.
Tighten power cord connection and turn on computer.
Make sure the first display of a dual-headed system or the only display of a single-headed system is connected to the
Video 1 port on the display controller. (See page 9 .)
Turn off DPMS mode.
Turn off computer and secure connections.
Turn off computer and secure connections.
Use a VESA DPMS-compliant computer or video controller.
Turn off computer. Check and secure connection.
Check computer power and graphics adapter configuration.
Dome C3i Display 14
QUICK LINKS
Contents
Index
Regulatory Compliance
Product Information
Warranty
GETTING STARTED
About the Display
Package Contents
Identify Components
Position Display
Desk Stand Features
INSTALLING THE DISPLAY
Set DIP Switch
Install Display Controller
Connect Video and Power
Install Display Driver
Change Display Properties
Dome CXtra Software
APPENDIXES
Troubleshooting
Specifications
LED Status Lights
Single Desktop
USB Connection
Component Removal
Power Management
Palette Options
Problem
VGA not enabled
Conflict with driver versions
Dome C3i Display
Possible cause Solution
Incorrect DIP switch settings.
You may need to remove the display controller to check the DIP switch settings. You can enable VGA on the display controller or use a separate VGA card. See page 7 for the correct switch positions to enable or disable VGA, depending on your system.
A previous version of the display driver is still installed on the computer system.
Remove any existing Dome display driver before you install
a more recent version.
The installation CD contains a file older than the one currently on your system.
The Confirm File Replace dialog box appears if the installation CD contains a file older than the one currently
on your system. Click No to the question Overwrite the newer file? or click No to All.
15
QUICK LINKS
Contents
Index
Regulatory Compliance
Product Information
Warranty
GETTING STARTED
About the Display
Package Contents
Identify Components
Position Display
Desk Stand Features
INSTALLING THE DISPLAY
Set DIP Switch
Install Display Controller
Connect Video and Power
Install Display Driver
Change Display Properties
Dome CXtra Software
APPENDIXES
Troubleshooting
Specifications
LED Status Lights
Single Desktop
USB Connection
Component Removal
Power Management
Palette Options
C3i Display Specification
Display Category
Screen
Characteristic Item
Screen size diagonal
Resolution
Interface
Input formats
Physical
Power requirements
Pixel pitch
Pixel arrangement
Active area
Grayscale supported
Refresh rate
Contrast ratio
Brightness
Pixel rise/fall time
Viewing angle
Digital Video In
Display control - brightness/contrast
Display identification
USB hub
Monitor status
Landscape orientation
Portrait orientation
VGA™/XGA
Screen type
Display size (without stand)
Display weight (without stand)
Mounting options
Input voltage
Power consumption
Dome C3i Display
Specification
528 mm (20.8 in.)
1536 x 2048 pixels (portrait)
2048 x 1536 pixels (landscape)
0.207 mm x 0.207 mm
Subpixel vertical stripe
423.9 mm (H) x 318.0 mm (V)
3061 shades of gray
60 Hz
600:1 (typical)
800 cd/m
2
(typical)
50 ms
170° (± 85°) horizontal/vertical
2 DVI single-channel digital connectors
DDC2B+
EDID read using DDC2B+
Universal Serial Bus (USB) Rev. 1.1: 1 uplink B port; 2 downlink A ports
Dual stack tricolor LEDs on back panel
2048 x 1536 (8- and 24-bit per pixel)
1536 x 2048 (8- and 24-bit per pixel) with automatic hardware rotate
640 x 480 to 1024 x 768 pixels displayed in both landscape and portrait rotation
AMLCD (active-matrix liquid crystal display)
485.78 mm x 381 mm x 101.6 mm (19.125 in. x 15 in. x 4 in.)
6.35 kg (14 lb)
100-mm VESA mounting standard
+12 V ± 10%
90 Watts maximum
16
QUICK LINKS
Contents
Index
Regulatory Compliance
Product Information
Warranty
GETTING STARTED
About the Display
Package Contents
Identify Components
Position Display
Desk Stand Features
INSTALLING THE DISPLAY
Set DIP Switch
Install Display Controller
Connect Video and Power
Install Display Driver
Change Display Properties
Dome CXtra Software
APPENDIXES
Troubleshooting
Specifications
LED Status Lights
Single Desktop
USB Connection
Component Removal
Power Management
Palette Options
Power Supply
Category
Power input requirements
Power output requirements
Physical
Dome C3i Display
Characteristic Item
Voltage selection
Voltage
Current
Frequency
Voltage
Current
Size
Weight
Specification
Auto-ranging
100 – 240V AC
2.0 A
50 to 60 Hz
12 V DC ± 5%
10.0 A (120 W)
228.6 mm x 76.2 mm x 50.8 mm (9 in x 3 in x 2 in)
1.3 kg (2.75 lb)
17
QUICK LINKS
Contents
Index
Regulatory Compliance
Product Information
Warranty
GETTING STARTED
About the Display
Package Contents
Identify Components
Position Display
Desk Stand Features
INSTALLING THE DISPLAY
Set DIP Switch
Install Display Controller
Connect Video and Power
Install Display Driver
Change Display Properties
Dome CXtra Software
APPENDIXES
Troubleshooting
Specifications
LED Status Lights
Single Desktop
USB Connection
Component Removal
Power Management
Palette Options
Reliability
Characteristic item
Display plus backlight
Backlight
Environment
Characteristic item
EMI shielding
Temperature operating
Humidity storage operating
Altitude storage operating shipping/storage
Dome C3i Display
Specification
MTBF 50,000 hours with 50% duty cycle on backlight
MTBF 30,000 hours to 50% brightness with backlight on continuously
Specification
No emission of low-level radiation
10° to 40° C
-10° to 60° C
20% to 80% Relative Humidity (non-condensing)
5% to 90% Relative Humidity (non-condensing)
3,000 meters (9,850 feet) maximum
12,000 meters (39,400 feet), maximum in unpressurized container
18
QUICK LINKS
Contents
Index
Regulatory Compliance
Product Information
Warranty
GETTING STARTED
About the Display
Package Contents
Identify Components
Position Display
Desk Stand Features
INSTALLING THE DISPLAY
Set DIP Switch
Install Display Controller
Connect Video and Power
Install Display Driver
Change Display Properties
Dome CXtra Software
APPENDIXES
Troubleshooting
Specifications
LED Status Lights
Single Desktop
USB Connection
Component Removal
Power Management
Palette Options
Video Modes
Resolutions expressed in pixels (W x H). Single desktop requires dual displays.
Resolution
1536 x 2048
2048 x 1536
3072 x 2048
4096 x 1536
1536 x 2048
2048 x 1536
3072 x 2048
4096 x 1536
Orientation
Portrait
Landscape
Portrait, single desktop
Landscape, single desktop
Portrait
Landscape
Portrait, single desktop
Landscape, single desktop
Palette available
Dynamic gray
Nonlinear gray
Static gray
True color
Bits per pixel
8
32
Dome C3i Display 19
QUICK LINKS
Contents
Index
Regulatory Compliance
Product Information
Warranty
GETTING STARTED
About the Display
Package Contents
Identify Components
Position Display
Desk Stand Features
INSTALLING THE DISPLAY
Set DIP Switch
Install Display Controller
Connect Video and Power
Install Display Driver
Change Display Properties
Dome CXtra Software
APPENDIXES
Troubleshooting
Specifications
LED Status Lights
Single Desktop
USB Connection
Component Removal
Power Management
Palette Options
Connector Ports
The video signal connector is a standard DVI connector, driving power and data to the display. The Dome C3i display use an 8-pin DIN connector. The power input is
12V ±5% (90 W).
Dome C3i Display
Power connector in the Dome C3i display
DIN connector
Details of the 8-pin DIN connector.
VCC 8
VCC 7 1 GND
VCC 6
VCC 5
4 GND
2 GND
3 GND
20
QUICK LINKS
Contents
Index
Regulatory Compliance
Product Information
Warranty
GETTING STARTED
About the Display
Package Contents
Identify Components
Position Display
Desk Stand Features
INSTALLING THE DISPLAY
Set DIP Switch
Install Display Controller
Connect Video and Power
Install Display Driver
Change Display Properties
Dome CXtra Software
APPENDIXES
Troubleshooting
Specifications
LED Status Lights
Single Desktop
USB Connection
Component Removal
Power Management
Palette Options
LED Status Lights
The two LEDs on the back panel provide information about the display.
• LED A describes the digital-link status between the display controller and the interface.
• LED B describes the display-panel status. It shows any faults currently in the panel.
Power-up sequence information from LED
LED A
Solid green
Action/Sequence
Initial power-on
Flashing yellow
Solid yellow
One (1) second after power-on
Two seconds after power-on
Dome C3i Display
Reset button (left) and LEDs on the connector plate
LED A, top
LED B
LED B
Solid green
Flashing yellow
Solid yellow
Description
One (1) second of solid green to verify the green LED works.
One (1) second of flashing yellow to verify the yellow LED works.
One (1) second of solid yellow to verify the yellow LED works.
21
QUICK LINKS
Contents
Index
Regulatory Compliance
Product Information
Warranty
GETTING STARTED
About the Display
Package Contents
Identify Components
Position Display
Desk Stand Features
INSTALLING THE DISPLAY
Set DIP Switch
Install Display Controller
Connect Video and Power
Install Display Driver
Change Display Properties
Dome CXtra Software
APPENDIXES
Troubleshooting
Specifications
LED Status Lights
Single Desktop
USB Connection
Component Removal
Power Management
Palette Options
LED A status information after initial power-on
LED Status
Solid green
Flashing green
Flashing yellow
Solid yellow
Dome C3i Display
Description
Fault
Functional link – normal operation
Link working, unrecognized sync information
Receiving DDC information
LED B status information after initial power-on
LED Status
Solid green
Flashing green
Description
Fault
Functional system – normal operation
22
QUICK LINKS
Contents
Index
Regulatory Compliance
Product Information
Warranty
GETTING STARTED
About the Display
Package Contents
Identify Components
Position Display
Desk Stand Features
INSTALLING THE DISPLAY
Set DIP Switch
Install Display Controller
Connect Video and Power
Install Display Driver
Change Display Properties
Dome CXtra Software
APPENDIXES
Troubleshooting
Specifications
LED Status Lights
Single Desktop
USB Connection
Component Removal
Power Management
Palette Options
Single Desktop
The single desktop mode converts dual Dome C3i displays into one display device to meet the requirements of some applications. The single desktop mode is supported on the Dome C3i display in both portrait and landscape modes.
On the display controller, switch 3 on DIP switch must be in the ON position for each procedure. (See page 7 .)
To change the configuration to single desktop
If you are working on a dual-headed display, you can use the following procedure to change your hardware and software configuration to single desktop.
1 Uninstall any existing DX2 display driver. See “To uninstall the driver” on page 27 .
2 On the DIP switch, place switch 3 in the ON position. (See page 7 .)
3 Reinstall the display controller. (See page 8 .) Then attach both displays to the controller. (See page 9 .)
4 Power on the system, and run Setup.exe to install the driver. (See page 10 .)
5 Set the display resolution. (See page 11 ).
Dome C3i Display 23
QUICK LINKS
Contents
Index
Regulatory Compliance
Product Information
Warranty
GETTING STARTED
About the Display
Package Contents
Identify Components
Position Display
Desk Stand Features
INSTALLING THE DISPLAY
Set DIP Switch
Install Display Controller
Connect Video and Power
Install Display Driver
Change Display Properties
Dome CXtra Software
APPENDIXES
Troubleshooting
Specifications
LED Status Lights
Single Desktop
USB Connection
Component Removal
Power Management
Palette Options
To restore the configuration dual display mode
1 Uninstall any existing DX2 display driver. See “To uninstall the driver” on page 27 .
2 On the DIP switch, place switch 3 in the OFF position. (See page 7 .)
3 Reinstall the display controller. (See page 8 .) Then attach both displays to the controller. (See page 9 .)
4 Power on the system, and run Setup.exe to install the driver. (See page 10 .)
5 Set the display resolution. (See page 11 ).
Dome C3i Display
Example for Dome C3i:
On the Dome tab, select resolution 3072 x 2048 for the single desktop in portrait mode
Safety precaution
Wear an antistatic wrist strap when handling the board and display to prevent electrostatic discharge.
24
QUICK LINKS
Contents
Index
Regulatory Compliance
Product Information
Warranty
GETTING STARTED
About the Display
Package Contents
Identify Components
Position Display
Desk Stand Features
INSTALLING THE DISPLAY
Set DIP Switch
Install Display Controller
Connect Video and Power
Install Display Driver
Change Display Properties
Dome CXtra Software
APPENDIXES
Troubleshooting
Specifications
LED Status Lights
Single Desktop
USB Connection
Component Removal
Power Management
Palette Options
To get information
Open the Dome tab to retrieve information on the two displays you are using to run single desktop. Information for both left and right panels appears at the bottom of the Dome tab, as shown in this illustration. See page 12 for more information.
Dome C3i Display 25
QUICK LINKS
Contents
Index
Regulatory Compliance
Product Information
Warranty
GETTING STARTED
About the Display
Package Contents
Identify Components
Position Display
Desk Stand Features
INSTALLING THE DISPLAY
Set DIP Switch
Install Display Controller
Connect Video and Power
Install Display Driver
Change Display Properties
Dome CXtra Software
APPENDIXES
Troubleshooting
Specifications
LED Status Lights
Single Desktop
USB Connection
Component Removal
Power Management
Palette Options
USB Connection
The display desk stand contains an integrated, self-powered USB hub that allows you to attach USB devices (such as a keyboard or mouse) to the Dome C3i display rather than to a computer.
To use the USB ports
1 Use a Type A-B USB cable to connect the USB B port on the desk stand to the USB A port on your USB-compliant computer or other hub.
2 Connect USB-compliant peripherals to the USB A ports on the desk stand.
Dome C3i Display
B A
Legend
A USB A (downstream) port
B USB B (upstream) port
USB tips
To activate the USB hub function, connect the display to a USBcompliant computer or another hub with the Type A-B USB cable.
Use USB devices connected to the display even when the display is in power-saving mode.
Use USB devices connected to the display even when the display is unplugged from the power source.
The USB hub on the desk stand is powered by the computer.
26
QUICK LINKS
Contents
Index
Regulatory Compliance
Product Information
Warranty
GETTING STARTED
About the Display
Package Contents
Identify Components
Position Display
Desk Stand Features
INSTALLING THE DISPLAY
Set DIP Switch
Install Display Controller
Connect Video and Power
Install Display Driver
Change Display Properties
Dome CXtra Software
APPENDIXES
Troubleshooting
Specifications
LED Status Lights
Single Desktop
USB Connection
Component Removal
Power Management
Palette Options
Display Driver and Controller Removal
Use the following procedure to uninstall the display driver and display controller.
To uninstall the driver
1 Insert the W2KDXPCI CD and open the CD folder.
2 Double-click Setup.exe. The Welcome dialog box appears.
3 Select Remove, and click Next.
4 Click OK to confirm uninstall.
5 Select Yes, I want to restart my computer now, and click Finish.
6 Shut down the computer and remove the display controller.
Dome C3i Display
Safety precaution
Wear an antistatic wrist strap when handling the display controller to prevent electrostatic discharge.
27
QUICK LINKS
Contents
Index
Regulatory Compliance
Product Information
Warranty
GETTING STARTED
About the Display
Package Contents
Identify Components
Position Display
Desk Stand Features
INSTALLING THE DISPLAY
Set DIP Switch
Install Display Controller
Connect Video and Power
Install Display Driver
Change Display Properties
Dome CXtra Software
APPENDIXES
Troubleshooting
Specifications
LED Status Lights
Single Desktop
USB Connection
Component Removal
Power Management
Palette Options
Power Management
You have two ways to lower energy usage when the Dome C3i display is idle:
• Dome CXtra Backlight Saver service (preferred)
• DPMS (Display Power Management Signaling)
Activate the power saver when you anticipate periods of inactivity, such as at the end of the work day. Once activated, Backlight Saver (or DPMS) automatically turns the backlight off during the period of inactivity. Backlight Saver and DPMS both extend the life of the backlight and reduce burn-in of images.
To activate DPMS, use the display with a computer that has power-saving circuitry.
Computers running the Windows XP or Windows 2000 operating system have this feature built in.
The backlight lasts approximately 30,000 on-time hours.
Do not use the Backlight Saver and DPMS concurrently.
Dome C3i Display 28
QUICK LINKS
Contents
Index
Regulatory Compliance
Product Information
Warranty
GETTING STARTED
About the Display
Package Contents
Identify Components
Position Display
Desk Stand Features
INSTALLING THE DISPLAY
Set DIP Switch
Install Display Controller
Connect Video and Power
Install Display Driver
Change Display Properties
Dome CXtra Software
APPENDIXES
Troubleshooting
Specifications
LED Status Lights
Single Desktop
USB Connection
Component Removal
Power Management
Palette Options
Palette Options
The display controller supports different palette options on Windows systems.
In the Palette Options field of the Dome tab, use the pull-down menu to select a palette. Then click Apply or OK.
Dome palette options must coordinate with the primary display. All flat panels must be set to either palette devices or non-palette devices, as shown in this table.
Palette Device
• Dynamic gray
Non-Palette Device
• Nonlinear static gray
• Static gray
All Dome display controllers that support multiple displays also support differing palette options on multiple screens attached to the same controller.
See the assignment of values on the grayscale palettes on page 30 .
Dome C3i Display 29
QUICK LINKS
Contents
Index
Regulatory Compliance
Product Information
Warranty
GETTING STARTED
About the Display
Package Contents
Identify Components
Position Display
Desk Stand Features
INSTALLING THE DISPLAY
Set DIP Switch
Install Display Controller
Connect Video and Power
Install Display Driver
Change Display Properties
Dome CXtra Software
APPENDIXES
Troubleshooting
Specifications
LED Status Lights
Single Desktop
USB Connection
Component Removal
Power Management
Palette Options
Assignment of values on the grayscale palettes
Palette options with multiple displays
The SelectPalette and RealizePalette functions in the Microsoft Developer’s
Network, or MSDN, work across all flat-panel displays if the primary panel is palettized. The palettes of all palette-type devices are synchronized. If, however, the primary panel is not palettized, the SelectPalette and RealizePalette functions select the palette into the background, and palettized devices are not synchronized.
Dome C3i Display 30
QUICK LINKS
Contents
Index
Regulatory Compliance
Product Information
Warranty
GETTING STARTED
About the Display
Package Contents
Identify Components
Position Display
Desk Stand Features
INSTALLING THE DISPLAY
Set DIP Switch
Install Display Controller
Connect Video and Power
Install Display Driver
Change Display Properties
Dome CXtra Software
APPENDIXES
Troubleshooting
Specifications
LED Status Lights
Single Desktop
USB Connection
Component Removal
Power Management
Palette Options
Desktop icons
The palette specifications of the primary display determine how desktop icons are drawn. For example, the desktop icons appear gray on a color screen if the primary display is set to a gray palette.
The following table lists the palette options available on primary and secondary displays. A check mark (
✔
) indicates the palette combination that works.
SECONDARY DISPLAY
PRIMARY
Dynamic gray
Nonlinear static gray
Static gray
True color
DISPLAY
Pseudocolor
Dynamic gray
Nonlinear static gray Static gray True color Pseudocolor
✔ ✔ ✔
✔
✔
✔
✔
✔ ✔
✔
✔ ✔
✔
✔
✔
Dynamic gray palette
The dynamic gray palette reserves the first and last 10 entries in the palette for the
Windows NT operating system, but you can manipulate the middle 236 entries.
Your application can create a 256-entry gray ramp in any 8-bit driver by calling the
Windows API function SetSystemPaletteUse(), but doing so causes all icons to be redrawn in black and white.
The dynamic gray palette accommodates gray-mapped Windows colors for the first and last 10 palette entries.
Dome C3i Display 31
QUICK LINKS
Contents
Index
Regulatory Compliance
Product Information
Warranty
GETTING STARTED
About the Display
Package Contents
Identify Components
Position Display
Desk Stand Features
INSTALLING THE DISPLAY
Set DIP Switch
Install Display Controller
Connect Video and Power
Install Display Driver
Change Display Properties
Dome CXtra Software
APPENDIXES
Troubleshooting
Specifications
LED Status Lights
Single Desktop
USB Connection
Component Removal
Power Management
Palette Options
Nonlinear static gray palette
The nonlinear static gray palette sets the first and last 10 palette entries to graymapped Windows colors. The middle 236 entries are ramped in ascending order, excluding the first and last 10 palette entries. Windows applications that use the first and last 10 palette entries as Windows colors display correctly on the screen.
Although the nonlinear static gray palette provides correct colors for applications using the Windows palette, colors display incorrectly if the application assumes that a static palette is always ramped.
Static gray palette
The static gray palette provides 256 shades of gray in a static palette. This palette does not reserve the first and last 10 palette entries for icons and other standard
Windows graphics, which frees the entire grayscale ramp for applications.
The static gray palette does not provide gray-mapped Windows colors for the first and last 10 palette entries. Because the framebuffer assumes the Windows palette is in use, applications that draw directly to the framebuffer display incorrectly.
For example, icons and button bitmaps may display in black and white.
Dome C3i Display
Note
Applications cannot set the nonlinear static gray palette or the static gray palette. They must read the palette from the operating system and use it when drawing directly to the framebuffer.
Application colors display incorrectly if the application assumes all 8-bit framebuffers have palettes that can be set.
32
QUICK LINKS
Contents
Index
Regulatory Compliance
Product Information
Warranty
GETTING STARTED
About the Display
Package Contents
Identify Components
Position Display
Desk Stand Features
INSTALLING THE DISPLAY
Set DIP Switch
Install Display Controller
Connect Video and Power
Install Display Driver
Change Display Properties
Dome CXtra Software
APPENDIXES
Troubleshooting
Specifications
LED Status Lights
Single Desktop
USB Connection
Component Removal
Power Management
Palette Options
Dome C3i Display
Index
A
AMLCD, intended use ix
B backlight conserving 28 specifications 28 brightness, setting 11
C calibration 1
,
13 caring for display xii changing display properties 11 cleaning display xii components, identifying 3 connecting display 9 connectors
DVI 3 power 3
,
20 conserving backlight 28 customer support 37
CXtra 13
D desktop icons 31 setting single view 23 determining screen assignments 11
DICOM standard 1
,
13
DIN power connector 3
,
20
DirectDraw, disabling 12 display connecting 9 installing 9 display controller installation 8
Display Power Management Signaling x , 28 display properties, changing 11 display setup setting properties 11 display setup for Windows 2000 desktop icons 31 multiple displays 30 display specifications 16 disposal, display xii
Dome CXtra 1 , 13 , 28
Dome tab getting information 25 setting display properties 11
DPMS. See Display Power Management
Signaling driver options, setting 12
DVI connector 3 dynamic gray palette 31
F fire, preventing x flat-panel display information about 25
G grayscale display 29
I identifying components 3 imaging, medical 1 information product ix retrieving display system 12 technical 16 injury, preventing x input formats 16 installation file, overwriting 15 intended use ix interface specifications 16
L
LCD screen, cleaning xii
LED back panel 3 power-up sequence 21 status information after power-on 22
M maintenance of display xii medical imaging 1
N nonlinear static gray palette 32
O overwriting installation file 15
33
QUICK LINKS
Contents
Index
Regulatory Compliance
Product Information
Warranty
GETTING STARTED
About the Display
Package Contents
Identify Components
Position Display
Desk Stand Features
INSTALLING THE DISPLAY
Set DIP Switch
Install Display Controller
Connect Video and Power
Install Display Driver
Change Display Properties
Dome CXtra Software
APPENDIXES
Troubleshooting
Specifications
LED Status Lights
Single Desktop
USB Connection
Component Removal
Power Management
Palette Options
Dome C3i Display
P palette combinations 31 options 29 options, multiple displays 30 options, setting 11 power connector 3 , 20 requirements 16 usage 28 power-up sequence, LED 21 precautions cleaning xii installing xi safety x preventing fire or injury x product information ix
R
Reset button 3 resolution 19 , 21 setting display 11 retrieving display system information 12
RightLight sensor 1
,
13
S safety precautions x screen cleaning xii saver 28 specifications 16 screen assignments, determining 11 setting brightness 11 driver options 12 palette options 11 single desktop 23 setting resolution 11 shipping or storing display xii single desktop 23 getting information 25 restoring dual-display mode 24 switching from dual-headed display 23 software, Dome CXtra 1
,
13
,
28 specifications backlight 28 display 16 interface 16 screen 16 static gray palette 32 status, LEDs 22
T tips, USB 26
U
USB connection 26 tips 26
V video modes, preset 19 , 21
34
QUICK LINKS
Contents
Index
Regulatory Compliance
Product Information
Warranty
GETTING STARTED
About the Display
Package Contents
Identify Components
Position Display
Desk Stand Features
INSTALLING THE DISPLAY
Set DIP Switch
Install Display Controller
Connect Video and Power
Install Display Driver
Change Display Properties
Dome CXtra Software
APPENDIXES
Troubleshooting
Specifications
LED Status Lights
Single Desktop
USB Connection
Component Removal
Power Management
Palette Options
Overview of Standard Warranty
Summary
• Standard 1-year “repair and return” warranty
• Industry-leading 10-year backlight warranty
1
• Typical repair turnaround time of 10 business days
Standard Warranty Return Procedure
As a Planar Standard Warranty customer, you must follow the procedure below if you have a non-functioning Dome CX display. The Planar customer service staff will attempt to correct any minor issues that may be causing the problem. Once Planar has determined that you have a non-functioning product, Planar will arrange for return and repair of the non-functioning product.
1 Contact Planar via the web at http://www.planar.com/support . In North America, call
(866) PLANAR1 (866.752.6271). In Europe, call +358 9 420 01 or send your info by fax to +358 9 420 0200. You must have the model number, serial number, and proof-ofpurchase available.
2 Planar customer service staff will attempt to correct any minor issues that may be causing the problem. If we are unable to correct the problem to your satisfaction, we will issue a Return Material Authorization (RMA).
3 You must return the product, as specified, to Planar Systems. Planar will validate the defect, repair the unit, and return the unit to you. The typical turnaround time is
10 business days.
1 If, within 10 years of initial purchase, the maximum output of the Dome CX warranty
is determined by Planar Systems to be less than 300 cd/m
2
, Planar will repair or replace the display, at the its sole discretion.
Dome C3i Display 35
QUICK LINKS
Contents
Index
Regulatory Compliance
Product Information
Warranty
GETTING STARTED
About the Display
Package Contents
Identify Components
Position Display
Desk Stand Features
INSTALLING THE DISPLAY
Set DIP Switch
Install Display Controller
Connect Video and Power
Install Display Driver
Change Display Properties
Dome CXtra Software
APPENDIXES
Troubleshooting
Specifications
LED Status Lights
Single Desktop
USB Connection
Component Removal
Power Management
Palette Options
Summary Limitations and Exclusions of Dome Displays
1 Customer must provide original proof of purchase of the display system.
2 Warranty is void on any product with a defaced, modified, or removed serial number.
3 Warranty is void on any product with damage, deterioration, or malfunction resulting from the following: a) Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product modification, or failure to follow instructions supplied with the product.
b) Repair or attempted repair by anyone not authorized by Planar.
c) Any damage of the product due to shipment.
d) Removal or installation of the product.
e) Causes external to the product, such as electric power fluctuations or failure.
f) Use of supplies or parts not meeting Planar's specifications.
g) Normal wear and tear.
h) Any other cause, which does not relate to a product defect.
4 Warranty excludes removal, installation, and setup service charges.
Limitation of Implied Warranties
THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED, WHICH EXTEND BEYOND THE
DESCRIPTION CONTAINED HEREIN INCLUDING THE IMPLIED WARRANTY OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
Dome C3i Display 36
QUICK LINKS
Contents
Index
Regulatory Compliance
Product Information
Warranty
GETTING STARTED
About the Display
Package Contents
Identify Components
Position Display
Desk Stand Features
INSTALLING THE DISPLAY
Set DIP Switch
Install Display Controller
Connect Video and Power
Install Display Driver
Change Display Properties
Dome CXtra Software
APPENDIXES
Troubleshooting
Specifications
LED Status Lights
Single Desktop
USB Connection
Component Removal
Power Management
Palette Options
Exclusion of Damages
THE LIABILITY OF PLANAR IS LIMITED TO THE COST OF REPAIR OR REPLACEMENT OF
THE PRODUCT. PLANAR SHALL NOT BE LIABLE FOR THE FOLLOWING:
1 DAMAGE TO OTHER PROPERTY CAUSED BY ANY DEFECTS IN THE PRODUCT,
DAMAGES BASED UPON INCONVENIENCE, LOSS OF USE OF THE PRODUCT, LOSS OF
TIME, LOSS OF PROFITS, LOSS OF BUSINESS OPPORTUNITY, LOSS OF GOODWILL,
INTERFERENCE WITH BUSINESS RELATIONSHIPS, OR OTHER COMMERCIAL LOSS,
EVEN IF ADVISED OF THEIR POSSIBILITY OF SUCH DAMAGES.
2 ANY OTHER DAMAGES, WHETHER INCIDENTAL, INDIRECT, CONSEQUENTIAL OR
OTHERWISE.
3 ANY CLAIM AGAINST THE CUSTOMER BY ANY OTHER PARTY.
Effect of Local Law
This warranty gives you specific legal rights, and you may have other rights, which vary from locality to locality. Some localities do not allow limitations on implied warranties and/or do not allow the exclusion of incidental or consequential damages, so the above limitations and exclusions may not apply to you.
Dome C3i Display
Technical assistance
In North America
Call 1 (866) PLANAR1 between
8 A .
M . and 5 P .
M . Pacific time,
Monday through Friday, or send a description of your technical issues and e-mail address to [email protected]
.
In Europe
Call +358 9 420 01 between 8
A
.
M
. and 4
P
.
M
. Finnish time (Eastern
European time), Monday through
Friday, or send a description of your technical issues and e-mail address to [email protected]
.
37
advertisement
Related manuals
advertisement