advertisement
MEITRACK T311 User Guide
MEITRACK T311 User Guide
MEITRACK T311 User Guide
File Name
Project
Subproject
Version
Change History
MEITRACK T311 User Guide
T311
User Guide
V1.6
Created By
Creation Date
Update Date
Total Pages
Confidential
Kyle Lv
2014-08-01
2015-09-30
17
External Documentation
Copyright © 2015 Meitrack Group All rights reserved. - 2 -
MEITRACK T311 User Guide
Contents
Copyright © 2015 Meitrack Group All rights reserved. - 3 -
MEITRACK T311 User Guide
1 Copyright and Disclaimer
Copyright © 2015 MEITRACK. All rights reserved. and are trademarks that belong to Meitrack Group.
The user manual may be changed without notice.
Without prior written consent of Meitrack Group, this user manual, or any part thereof, may not be reproduced for any purpose whatsoever, or transmitted in any form, either electronically or mechanically, including photocopying and recording.
Meitrack Group shall not be liable for direct, indirect, special, incidental, or consequential damages (including but not limited to economic losses, personal injuries, and loss of assets and property) caused by the use, inability, or illegality to use the product or documentation.
2 Product Overview
The T311 is an anti-theft GPS tracking device specially designed for motorcycles and electric vehicles. The T311 is equipped with a wireless remote control and a buzzer, so that vehicle arming, disarming, and keyless start can be implemented. In arming state, if a vehicle is faulty, the buzzer will generate an alarm, and thus the engine is stopped and the vehicle is locked to prevent stealing.
3 Product Function and Specifications
3.1 Product Function
3.1.1 Position Tracking
GPS + GSM dual-module tracking
Real-time location query
Track by time interval
Track by distance
Track by mobile phone
Speeding alarm
Direction change alarm
3.1.2 Anti-Theft
(Optional) SOS alarm by remote control
Arming/Disarming
Towing alarm
(Optional) Electric vehicle anti lock motor
(Optional) Remote engine stop
GPS blind spot alarm
External power cut-off alarm
Buzzer alarm
Geo-fence
Copyright © 2015 Meitrack Group All rights reserved. - 4 -
MEITRACK T311 User Guide
3.1.3 Other Functions
SMS/GPRS (TCP/UDP) communication (Meitrack protocol)
Built-in 8 MB buffer for driving trace recording
Low battery alarm
Water resistant IP65
(Optional) Electric vehicle keyless drive
(Optional) Motorcycle keyless start/flameout
(Optional) Panic button
3.1.4 Functions of Optional Accessories
Accessory
Wireless remote control
Function
Arming/Disarming
Keyless start/flameout
Keyless drive
Panic button
Improve the GPS signal reception. External GPS antenna
3.2 Specifications
Item
GSM frequency band
GPS sensitivity
Positioning accuracy
Dimension
Specifications
GSM 850/900/1800/1900 MHz
-162 dB
10m
86 mm x 65 mm x 25 mm
Weight
Coordinate system
Input voltage
Built-in battery
165g
WGS-84
DC 11–90 V/1.5 A
730 mAh/3.7 V
Normal power consumption 60 mAh
Operating temperature -22°C to 55°C
GSM antenna Internal antenna
GPS antenna
Built-in memory chip
Sensor
Wireless remote control
Port
Internal antenna (the side with the logo facing upwards)
(Optional) External antenna
8 MB
3D acceleration sensor (for wake-up by vibration and towing alarms)
RF 433 MHz
1 positive output
1 input for motorcycle flameout (upper flameout cable)
1 output for motorcycle flameout (lower flameout cable)
1 output for motorcycle start or input for electric vehicle motor start detection
1 input for motorcycle positive/negative start
1 output for a buzzer alarm
Copyright © 2015 Meitrack Group All rights reserved. - 5 -
MEITRACK T311 User Guide
1 USB port
1 wireless remote control antenna
1 negative terminal connection cable
4 T311 and Accessories
T311 and standard accessories:
T311 with a built-in battery Motorcycle cable
USB cable
Optional accessories:
CD
Buzzer
3M double sided tape
Electric vehicle cable
External GPS antenna
5 First Use
5.1 Installing the SIM Card
1. Remove the back cover.
Wireless remote control
Turn off the device. With the back panel facing you, use the mini screwdriver to remove the two screws to release the back cover. Then lift up the back cover from the notch at the bottom of the device.
2. Insert the SIM card.
Copyright © 2015 Meitrack Group All rights reserved. - 6 -
MEITRACK T311 User Guide
Gently push the SIM card into the slot until you hear a click with the gold-plated contacts facing down.
Note: Before inserting the SIM card, turn off the device. Ensure that the PIN lock of the SIM card is closed properly, and the SIM card has sufficient balance and has subscribed the call ID service. If you want to use the GPRS function, learn about the SIM card GPRS charging first.
5.2 LED Indicator
Power button
GPS indicator (blue)
GSM indicator (green)
To start the T311, press and hold down the power button for 3s to 5s, or connect the T311 to external power supply.
GPS Indicator (Blue)
Steady on
Blink (0.1s on)
One button is pressed or one input is activated.
The tracker is being initialized or the battery power is low.
A GPS signal is received.
No GPS signal is received.
Blink (0.1s on and 2.9s off)
Blink (3s on)
GSM Indicator (Green)
Steady on
Blink (0.1s on)
Blink (0.1s on and 2.9s off)
Blink (3s on)
A call is coming in or a call is being made.
The tracker is being initialized.
A GSM signal is received.
No GSM signal is received.
5.3 Configured by Computer
This section describes how to use Meitrack Manager to configure the T311 on a computer.
Procedure:
1. Install the USB-to-serial cable (PL2303) driver and Meitrack Manager.
2. Connect the T311 to a PC by using the USB-to-serial cable.
Copyright © 2015 Meitrack Group All rights reserved. - 7 -
MEITRACK T311 User Guide
3. Run Meitrack Manager, then the following dialog box will appear:
Turn on the device, then Meitrack Manager will detect the device model automatically and the parameter page will appear accordingly.
For details about Meitrack Manager, see the MEITRACK Manager User Guide.
5.4 Tracking by Mobile Phone
This section describes how to query the current location of the T311, ensuring that the GPS is working normally.
Call the SIM card phone number that is used in the T311, and hang up after the dial tone rings 2-3 times.
Note: If an authorized phone number was set by SMS command A71, only this phone number can receive SMS reports.
A location SMS is received. Click the link in the SMS to query the location.
SMS example:
Now,110727 02:48,V,16,23Km/h,61%,http://maps.google.com/maps?f=q&hl=en&q=22.540103,114.082329
The following table describes the SMS format:
Parameter Description Remarks
SMS header: indicates the alarm type.
Now Indicates the current location.
For details about the SMS header, see the MEITRACK
Copyright © 2015 Meitrack Group All rights reserved. - 8 -
MEITRACK T311 User Guide
SMS Protocol and MEITRACK GPRS Protocol.
110727 02:48
Indicates the date and time in YYMMDD
hh:mm format.
None
V
16
The GPS is invalid.
Indicates the GSM signal strength.
A = Valid
V = Invalid
Value: 1–32
The larger the value is, the stronger the signal is. If the value is greater than 12, GPRS reaches the normal level.
Unit: km/h 23Km/h Indicates the speed.
61% http://maps.google.com/ maps?f=q&hl=en&q=22.5
40103,114.082329
Indicates the remaining battery power.
This is a map link.
Latitude: 22.540103
Longitude: 114.082329
None
None
If there is no valid GPS available, the tracker will reply the most recent valid position.
If your mobile phone does not support HTTP, enter the latitude and longitude on Google Maps to query a location.
5.5 Common SMS Commands
5.5.1 Setting a Function Phone Number
SMS sending: 0000,A71,Phone number 1,Phone number 2,Phone number 3
SMS reply: IMEI,A71,OK
Description:
Phone number: A function phone number has a maximum of 16 bytes. If no phone numbers are set, leave them blank. Phone numbers are empty by default.
Phone number 1/2/3: SOS phone numbers. When you call the tracker by using these phone numbers, SMSs of locations, geo-fence alarms, low power alarms, and speeding alarms are received, and calls and SMSs of car towing and stealing alarms are received.
If all function phone numbers need to be deleted, send 0000,A71.
When the SOS button is pressed, the tracker dials phone numbers 1, 2, and 3 in sequence. The tracker stops dialing when a phone number responds.
Copyright © 2015 Meitrack Group All rights reserved. - 9 -
MEITRACK T311 User Guide
Example: 0000,A71,13811111111,13822222222,13833333333
Reply: 353358017784062,A71,OK
5.5.2 Arming/Disarming
SMS sending: 0000,B21,Status
SMS reply: IMEI,B21,OK
Description:
When Status is 1, enable the arming function. In arming state, activating the engine is an unauthorized operation. If the operation is performed, the tracker will send an alarm SMS to the preset authorized phone number.
When Status is 0, disable the arming function. In disarming state, all anti-theft alarms will be cleared.
For details about SMS commands, see the MEITRACK SMS Protocol.
Note:
1. The default SMS command password is 0000. You can change the password by using Meitrack Manager and SMS commands.
2. The device can be configured by SMS commands with a correct password. After an authorized phone number is set, only the authorized phone number can receive the preset SMS event report.
5.6 Remote Control Functions
5.6.1 Definitions of RF Remote Control Keys
Current Vehicle State
Disarming state/ACC OFF
Arming state
Start state
ACC OFF
Any status
Function Key
Arm Key
Disarm Key
Start Key
Horn Key
Description
Press "Arm" key when the engine is off; and the tracker will confirm arming with a "beep" sound. While under this stage, if the vehicle is vibrated or attempted to start; the stealing alarm will be generated.
If the buzzer sounds “beep” twice, the arming state will be disabled.
Press "Disarm" key to cut off the vehicle.
Press the key twice to start the vehicle. If the vehicle is started by using the remote control in the arming state, the arming state will be automatically disabled.
Press and hold down ‘Horn’ key for 2 seconds; an SMS/GPRS SOS alarm will be generated.
The buzzer will sound for 4 seconds to alert the location of the vehicle.
ACC OFF
Copyright © 2015 Meitrack Group All rights reserved. - 10 -
MEITRACK T311 User Guide
5.6.2 RF Remote Control Code Matching Function
If the remote control does not match the tracker, match the code manually. There are the following two code matching modes:
1. ACC code matching mode a) In disarming state, turn the vehicle key in the lock for 8 times from ACC OFF to ACC ON, and stay on the ACC ON state. After 3s, the buzzer will sound “bi” 3 times to enter the code matching state. Note that if it takes more than
3s to turn the key twice, the number of key turning times will recount. b) Press any key on one remote control. If the buzzer sounds 3 times, the code is matched successfully. Then press any key on the other remote control, the buzzer sounds 3 times. In this way, you can exit the code matching state. If a same remote control is pressed twice, code matching performed later for other remote controls does not take effect. c) The code matching must be completed within 20s. Otherwise, the code matching state exits automatically. d) When more than one remote controls are implemented code matching, if a same remote control is pressed twice, code matching performed later for other remote controls does not take effect.
2. Command code matching mode a) Send the SMS/GPRS command 000,B24,1 to enter the code matching state. After the tracker receives the command, the buzzer will sound 3 times. b) If you have two remote controls, press any key on one remote control. If the buzzer sounds "bi" 3 times, the code is matched successfully. Then press any key on the other remote control, the buzzer sounds 3 times. In this way, you can exit the code matching state. c) The code matching must be completed within 20s. Otherwise, the code matching state exits automatically. d) When more than one remote controls are implemented code matching, if a same remote control is pressed twice, code matching performed later for other remote controls does not take effect.
6 MS03 Tracking System
Visit http://ms03.trackingmate.com, enter the user name and password, and log in to the MS03. (Purchase the login account from your provider.)
For more information about how to add a tracker, see the MEITRACK GPS Tracking System MS03 User Guide (chapter 4 "Getting
Started").
The MS03 supports the following functions:
Track by time interval or distance.
Query historical traces.
Set polygon geo-fences.
Bind driver and vehicle information.
View various reports.
Send commands in batches.
Support OTA updates.
For details, see the MEITRACK GPS Tracking System MS03 User Guide.
Copyright © 2015 Meitrack Group All rights reserved. - 11 -
MEITRACK T311 User Guide
7 Installing the T311
7.1 (Optional) Installing the GPS Antenna
Connect the GPS antenna to the GPS port on the side panel of the tracker. It is recommended that the antenna should face up to the sky and the antenna side with words should face downwards. Secure the antenna by using double sided tapes.
Note: Do not install the GPS antenna at a place with metals.
7.2 Installing an I/O Cable
7.2.1 Port Definition
The I/O cable includes the power cable, positive and negative input, and output.
Port Color Description
Connected to the positive wire, 11–90V, 10 A fuse. Positive power supply Red
Negative power
Black supply (GND)
Connected to the GND, negative wire.
Positive output/Lock motor
Upper flameout cable
Orange
Pink
Connected to the positive output line (that is, the ACC cable) of a lock motor on an electric vehicle or motorcycle. Used to detect whether the vehicle key switch is turned on or whether to output positive electricity by simulating the original lock motor when the vehicle is started remotely.
For motorcycle: Connected to the positive output cable.
For electric vehicle: Connected to the lock motor cable.
For motorcycle: remote flameout (Refer to the section 7.2.3 "Motorcycle
Lower flameout cable
Start cable
Grey
Blue
For motorcycle: remote flameout
For electric vehicle: anti lock motor. (Note: When the device is connected to an electric vehicle, the electric vehicle sheathed wire is blue.)
For motorcycle: remote start.
For electric vehicle: ACC detection.
For positive start motorcycle: When the green cable is connected to the red cable (the positive wire), positive current flows through to start the motorcycle.
For negative start motorcycle: When the green cable is connected to the black wire (GND), negative current drains to start the motorcycle.
(Refer to the section 7.2.3.3 "Positive/Negative Start Wiring Diagram.")
Buzzer output (PWM) cable 1
Brown Buzzer plug: connects to the buzzer.
Copyright © 2015 Meitrack Group All rights reserved. - 12 -
MEITRACK T311 User Guide
Buzzer output (PWM) cable 2
Positive/Negative selectable start cable
GDN
Remote antenna
USB232 cable
Black control
Baby blue
Bold black
7.2.2 Port Pictures
Green
For positive start motorcycle: When the green cable is connected to the red cable (the positive wire), positive current flows through to start the motorcycle.
For negative start motorcycle: When the green cable is connected to the black wire (GND), negative current drains to start the motorcycle.
If the device is installed on an electric vehicle, ignore the green cable.
(Refer to the section 7.2.3 "Motorcycle Wiring Diagram" and 7.2.4 "Electric
Connected to the GND cable or the vehicle body.
RF remote control antenna for signal receiving
Connected to the USB232 port. Used for parameter configuration and program upgrade.
Motorcycle cable
Buzzer output
Electric vehicle cable
USB232 port
Remote control antenna
Copyright © 2015 Meitrack Group All rights reserved. - 13 -
MEITRACK T311 User Guide
7.2.3 Motorcycle Wiring Diagram
7.2.3.1 Motorcycle DC Ignition Wiring Diagram
Turn the switch to the leftmost position (DC ignition mode):
Copyright © 2015 Meitrack Group All rights reserved. - 14 -
MEITRACK T311 User Guide
7.2.3.2 Motorcycle AC Ignition Wiring Diagram
Turn the switch to the rightmost position (AC ignition mode):
Copyright © 2015 Meitrack Group All rights reserved. - 15 -
MEITRACK T311 User Guide
7.2.3.3 Positive/Negative Start Wiring Diagram
Referring to the above diagrams, if positive current flows through to start the motorcycle, connect the green cable to the red cable; if negative current drains to start the motorcycle, connect the green cable to the black cable. (Green, red and black cables are from the tracker.)
If the device is installed on an electric vehicle, ignore the green cable.
Copyright © 2015 Meitrack Group All rights reserved. - 16 -
MEITRACK T311 User Guide
7.2.4 Electric Vehicle Wiring Diagram
7.3 Mounting the T311
Use cable ties to fasten the T311 on the motorcycle.
Note: The device side with the Meitrack logo faces upwards to get better GPS signal.
If you have any questions, do not hesitate to email us at [email protected].
Copyright © 2015 Meitrack Group All rights reserved. - 17 -
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement