Digitus DC-51101 Owner's Manual

Specifications
KVM
EXTENDER
DC-51101-LOCAL
Function
PC Connector
DC-51101-REMOTE
(Local)
(Remote)
Monitor Connector
Keyboard Connector
Mouse Connector
Mode Switch Button
RJ-45 Connector
Power
LEDs
Link
Video Resolution
Cable Distance
Power Adapter
Housing
Weight
Dimensions(LxWxH)
DC-51101-LOCAL
DC-51101-REMOTE
1 x HD-15 Female
None
(VGA / KB / MS)
1 x HD-15 Female
1 x 6 pin mini-DIN Female (PS/2)
1 x 6 pin mini-DIN Female (PS/2)
1
None
1
1
1
1280×1024@60HZ
300 m (Max.)
DC 9V 600mA
Aluminum
235 g
230 g
130x83.5x29.5 mm
DC-51101-LOCAL (LOCAL) REAR VIEW
No
1
2
3
Component
Power Jack
Monitor
Connector
PC Connector
Description
The power adaptor plugs here.
The VGA cable (HD-15) connects
to the monitor plugs in here.
The 3-in-1 cable to PC plugs here.
DC-51101-REMOTE (REMOTE) FRONT VIEW
Hardware Requirements
Required specifications
USER MANUAL
V1.0
Package Contents
 KVM Extender Local Unit
x1
 KVM Extender Remote Unit
x1
 User manual
x1
 Power adapter DC 9V/600mA
x2
 3-in-1 cable
x1
If any thing missed, please contact with your vendor.
1 x Highest resolution monitor.
Console 1 x PS/2 mouse.
1 x PS/2 keyboard.
1 x VGA, SVGA or Multisync card.
PC
1 x 6-pin mini-DIN (PS/2) mouse port.
1 x 6-pin mini-DIN (PS/2) keyboard port.
Cable 1 x 3-in-1 KVM cable or equivalent.
DC-51101-LOCAL (LOCAL) FRONT VIEW
 The extension of VGA, PS/2 keyboard, PS/2 mouse
signal up to 300 meter away by using the KVM
Extender and one CAT5 cable.
 High VGA resolution up to 1280x1024.
 Support Auto/Manual video quality adjustment.
 Support video gain, equalization and RGB skew adjust.
 Support 3 hot key to combine other equipment.
 Two control privilege modes – “Share” & “Local only”.
 Extra console port is available on Local side.
 Auto console selection between Local and Remote.
-1-
Component
1
CAT.5
Connector
2
Power LED
3
Link LED
4
5
PS/2 Mouse
PS/2 Keyboard
Description
Plugs the CAT5 cable into this
connector.
On when the unit power on.
Off when the unit has no power.
Flash when “Local Using only”.
On when links successfully.
Off when no link to Local unit.
Flash when Local Using.
The PS/2 Mouse plugs here.
The PS/2 Keyboard plugs here.
DC-51101-REMOTE (REMOTE) REAR VIEW
No
Features
No
Component
1
CAT.5
Connector
2
Power LED
3
4
5
6
Link LED
Mode SW
Button
PS/2 Mouse
PS/2 Keyboard
Description
Plugs the CAT5 cable into this
connector.
On when the unit power on.
Off when the unit has no power.
Flash when “Local Using only”.
On when links successfully.
Off when no link to Remote unit.
Flash when Remote using.
Toggle the mode switch between
“Share” & “Local only”
The PS/2 Mouse plugs here.
The PS/2 Keyboard plugs here.
-2-
No
1
2
Component
Power Jack
Monitor
Connector
Description
The power adaptor plugs in here.
The VGA cable (HD-15) connects
to the monitor plugs in here.
*P.S. Power and Link LED flash simultaneously when
KVM-E-PRO is in the “command mode”.
-3-
PC
Remote
Monitor
HD-15
VGA
cable
Rear View
Local
Monitor
to
to
KVM-L-PRO
(Local)
Remote
PS/2
Mouse
PS/2
Front View
Local
PS/2
Mouse
PS/2
Front View
KVM-R-PRO
(Remote)
KVM-R-PRO (Remote)
3 in 1
custom
cable
KVM-L-PRO (Local)
RemotePS/2
Keyboard
PS/2
Local
PS/2
Keyboard
PS/2
Scroll lock
Num lock
Shift (left/ right)
Key
“Scroll lock” is the hot key.
“Num lock” is the hot key.
“Ctrl” (left/ right) is the hot key.
-4-
Function
Press hot key (default: Scroll Lock) twice to enter the
command mode, and press below key to select, and
press “ESC” key to exit command mode.
Change hot key in Local and Remote
Operation
1. Connect PC console port by using standard 3-in-1
cable to Local. (First connects PS/2 mouse, then
connects PS/2 keyboard and VGA connector).
2. Connect CAT5 cable to Local.
3. Connect CAT5 cable to Remote.
4. Connect keyboard, mouse and monitor to Local.
5. Connect keyboard, mouse and monitor to Remote.
6. Power on PC and Local.
7. Check the VGA quality by the monitor. If the video
quality is not good. Please use hot key of Remote to
adjust the video quality.
DC 9V
600mA
Adaptor
DC 9V
600mA
Adaptor
HD-15
VGA
cable
Rear View
Installation
Key
L
S
Function
Switch to “Local only” mode.
Switch to “Share” mode.
The Local user can switch the mode by two ways:
 Toggle the push button in the front panel of Local.
 Press hot key (default: Scroll Lock) twice to enter the
command mode, and press below key. After operation,
press “ESC” key to exit command mode.
Local only mode:
 Only the Local user can access the PC. The Remote
user can’t access the PC (include the video).
 The Power LED of Local and Remote will flash to
remind both the Remote and the Local user that right
now only the Local can access the PC.
 Only the Local user can switch the access mode.
KVM-E-PRO supports two modes:
Share mode:
 The two users (Local and Remote) can access one PC
base on a first-come, first-served policy.
 When the Local user accessing the PC, the Link LED
of
Remote will flash to remind the other user that it can’t
access now, and vice versa.
Mode switch of KVM-E-PRO
Function
Adjust video quality Automatically.
Adjust video Gain.
Adjust video Equalization.
Adjust Red skew time.
Adjust Green skew time.
Adjust Blue skew time.
Set video and hot key to Default.
-6-
Trademarks:
All the companies, brand names, and product names
referred to this manual are the trademarks or registered
trademarks belonging to their respective companies.
1. If the Power LED of Remote is not on, please make
sure power adapter is connected to Remote.
2. If no video signal is displayed on the monitor.
(1) Please check all of VGA cable and CAT5 cable
is loosened or disconnected.
(2) 3-in-1 cable was not attached to PC during boot
up process.
(3) Power adapter is not connected.
3. If video signal is foggy or un-clear, please check VGA
connector, or low the VGA resolution for long cable. It is
highly recommended to use “optimal CAT5 cable
length” to get the best video quality and not to waste
unnecessary CAT5 cable.
4. For the PC without PS/2 connector, please apply
PS/2-to-USB adapter to Local.
Troubleshooting
NOTE: All the video parameters have 32 levels to adjust.
You can also press & hold ↑ or ↓ to continually adjust
video, and if you adjust it to the last level then there will
be a “long” beep sound.
Key
A
N
E
R
G
B
D
Press hot key (default: Scroll Lock) twice of Remote to
enter the command mode, and press below key to select
video adjustment function. Then press ↑ or ↓ key to adjust
the value. When finished, press “ESC” key to end adjust.
Our KVM Extender provides 2 ways to adjust video
quality: Manually or Automatically. The user can
process the adjustment by hot key as follow.
Configure Video quality by Remote User
-5-