advertisement
Save This Manual For
Future Reference
OWBeTS
manual
MODEL NO'S.
113,298721
113.298761
SAW WITH LEGS
TWO CAST IRON
TABLE EXTENSIONS
MOTOR AND
QUICK RELEASE
RIP FENCE
Serial
Number
Model and serial number may be found at the left-hand side of the base
You should record both model and
serial number in a safe place for future use,
SE/ RS/C R R FTSM R N
10-INCH _BLE SAW
FOR
YOUR
SAFETY:
Read ALL
INSTRUCTIONS
CAREFULLY.
oassembly
. operating
orepair parts
Sold by SEARS, ROEBUCK AND CO., Chicago, IL. 60684 U.S.A.
Printed in U.S.A.
Part No. SP5396
FULL ONE YEAR WARRANTY ON CRAFTSMAN TABLE SAW
if within one year from the date of purchase, this Craftsman Table Saw fail= due to a defect In material or workmanship, Sears will repair it, freeo! charge. This warranty applies only while this product is In use In the United States.
WARRANTY SERVICE IS AVAILABLE BY SIMPLY CONTACTINGTHE NEAREST SEARS SERVICE
CENTER/DEPARTMENT THROUGHOUT THE UNITED STATES.
THIS WARRANTY APPUES ONLY WHILE THIS PRODUCT IS USED IN THE UNITED STATES.
This warranty gives you specific legal righte, and you may also have other rights which vary from state to state.
SEARS, ROEBUCKAND CO., D/817 WA HoffmanEstates, IL 60195
safety instructions for table saw
Safety is a combination of common sense, staying alert and knowing how your table saw works.
Read this manual to understand this saw.
BEFORE USING THE SAW
WARNING: To avoid mistakes that could cause serious, permanent Injury, do not plug the saw in until the following steps have been satisfactorily completed.
4, GROUND THE SAW- This saw has an approved 3-
conductor cord and a 3-prong grounding type plug.
The plug fitsgrounding type outlets designed for 120 volt 15 amp circuits. The green conductor in the cord lethe grounding wire. To avoid electrocution. NEVER
connect the green wire to a live terminal.
5. To avoid injuryfrom electrical shock, make sure your fingers do not touch the plug's metal prongs when plugging in or unplugging the saw.
1. Assembly and Alignment (See pages 10- 24).
2. Learn the use and function of the ON-OFF Switch,
Guard, Spreader, Anti-Kickbackdevice, MiterGauge,
Fence, Table Insert and Blade Elevation and Bevel
Controls. (See page 25)
6. To avoid back injury, get help or use recommended
casterswhen you needto move the saw. Always get
help if you need to lilt the saw. Hold the saw close to yourbody. Bend yourknees so you can lift with your
legs, not your back.
3. Review and understanding of all safety instructions and operating procedures in this manual.
4. Review of the maintenance methods for this saw.
(See page 43)
Read the following DANGER label found on the front of the saw:
7. NEVER STAND ON TOOL. Serious injury could
occur it the tool tips or you accidentally hit the cutting
tool. Do not store anything above or near the tool where anyone might stand on the tool to reach them.
BEFORE EACH USE:
4. Inspect your saw.
WHEN INSTALLING OR MOVING THE SAW
1. AVOID DANGEROUS ENVIRONMENT.
Use the saw in a dry place protected from rain. Keep work area well lighted.
2. To avoid injury from unexpected saw movement:
A. To avoid injuryfrom accidental starting, unplug the saw, turn the switch off and remove the switch key before raising or removing the Guard, changing
the cutting tool, changing the setup or adjusting anything.
A. Put the saw on a firm level surface where there is B. Check for alignment of moving parts, binding of
B. Suppod the saw so thetable is level and the saw
does not rock.
C. Bolt the sawto the floorifit tends to slip walk,or
slide during normal use.
D. When using table extensions over 24 inches wide on any side of the saw, boltthe saw to the flooror
PrOP up the outer end of the extension from the floor to keep the saw from tipping,
3. Put the saw where neither operators nor bystanders
must stand in line with the saw blade.
_DANGER
' 1 PaeBd_ tzeroee
_j .
_
3._reach_ouridofovefsaw
4.
'
5. DG not do freehand cuts.
, tdade,
2 for ri_, works. If any part is missing, bent, or broken in any way, or any electrical parts don't work properly, turn the saw off and unplug the saw.
C. Replace damaged, n_ssing, or failed parts before using the saw again.
D Use the Sawblade Guard, Spreader, and Anti-
KickbackPawlsforany thru-sawing(wheneverthe blade comes though the top of the workpiece).
Make sure the Pawls work properly. Make surethe
Spreader is n line with the sawblade.
I_ween _2 and 2 _ from _rv_mg and_
!
E, REMOVE ADJUSTING KEYS AND WRENCHES.
Form habit of checking for and removing keys and adjusting wrenches from tool before turning it on.
F. To avoid injury from jams, slips or thrown pieces
(kickback and throwback):
1. USE ONLY "RECOMMENDED ACCESSO-
RIES" (See page 43).
Follow the instructions that come with the accessories.
Using other accessories may be dangerous.
2. Choose the right blade or cutting accessory for the material and the type of cutting you plan to do.
3. Never use gdnding wheels, abrasive cut-off wheels, friction wheels (metal slitting blades) wire wheels or buffingwheeL They canfly apart explosively.
4. Choose and inspect your cutting tool carefully.
a. To avoid cutting tool failure and thrown shrapnel (broken pieces of blade), use only 10" or
Smaller blades or other cutting tools marked for speeds of 3450 rpm or higher.
b. Always use unbroken, balanced blades designed to fit this saw's 5/8 inch arbor.
c. When thru-sawing (making cuts where the blade comes through the workpiece top), always use a 10 inch diameter blade.
This keeps the spreader in closest to the blade.
d. Do not overtighten arbor nut.
Use arbor
wrenches to "snug" it securely.
e. Use only sharp blades with properly set teeth.
Consult a professional blade sharpenerwhen in doubt.
f. Keep blades clean of gum and resin.
5..Adjust
table inserts flush with the table top.
NEVER use the saw without the proper insert.
6. Make sure all clamps and locks are tight and no parts have any excessive play.
_.Keep work area clean
A Cluttered areas and benches invite accidents.
Floor must not be slippery from wax or sawdust.
B. To avoid burns or other fire damage, never use the saw near flammable liquids, vapors or gases.
C. To avoid injury, don't do layout, assembly, or setup work on the table while the blade is spinning. It could cut or throw anything hitting the blade.
Plan ahead to protectyour eyes, hands, face, ears.
AVOID ACCIDENTAL STARTING - Make sure
switch is "OFF" before plugging saw in.
L Plan your work
A. USE THE RIGHT TOOL - Don't force tool or
attachment to do a job it was not designed for.
B. Dress for safety:
1. Do not wear loose clothing, gloves, neckties or jewelry (rings, wristwatches).
They can get caught and draw you into moving parts.
2. Wear nonslip footwear.
3. Tie back long hair.
4. Roll long sleeves above the elbow.
5. Noise levels vary widely.
To avoid possible hearing damage, wear ear plugs or muffs when using saw for long periods of time.
6. Any power saw can throw foreign objects into the eyes.
This can cause permanent eye damage.
Wear safety goggles (not glasses)
that comply with ANSI Z87.1 (shown on pack-
age). Everyday eyeglasses have only impact resistant lenses.
They are not safety glasses.
Safety goggles are available at Sears retail catalog stores. Glasses or goggles not in compliance with ANSI Z87.1 could seriously hurt you when they break.
WEAR YOUR
7. For dusty operations, wear a dust mask along with the safety goggles.
C. Inspect your workpiece.
to be cut.
Make sure there are no nails or foreign objects in the part of the workpiece
D. Plan your cut to avoid KICKBACKS and THROW-
BACKS - when a part or al! of the workpiece binds on the blade and is thrown violently back toward the front of the saw.
1. Never cut FREEHAND: Always use either a
Rip Fence, Miter Gauge or fixture to position and guide the work, so it won't twist, bind on the blade and kickback.
2. Make sure there's no debris between the workpiece and its supports.
3. When cutting irregularly shaped workpieces, plan your work so it will not slip and pinch the blade:
a. A piece of molding, for example, must tie flat
or be held by a fixture or jig that will not let it twist, rock or slip while being cut. Use jigs or fixtures where needed to prevent workpiece shifting.
b. Use a different, better suited type of tool for work that can't be made stable.
4. Use extra caution with large, very small or
awkward workpieces: a. Use extra supports (tables, saw horses, b!ocks,etc.) for anyworkpieces large enough totip when not held down to the table top.
NEVER use another personas a substitute for atable extension, or as additional support for a workpiece that is longer or wider than the basic saw table, or to help feed, support or pull the workpiece.
b. Nevercontinethepiecebeingcutoff.
Thatis,
the piece NOTagainstthe fence, mitergauge
or fixture. Never hold it, clamp it, touch it, or use length stops against it. It must be free to
move. If confined, itcouldget wedged against the blade and cause a kickback or throwback.
c. Never cut more than oneworkpiece at atime.
d. Never turn your table saw "ON" before clear- ing everything except the workpiece and related support devices off the table.
4. Plan the way youwill pushthe workplecethrough.
A. NEVER pull the workplece through.
Start and
finish the cut from the front of the table saw.
B. NEVER put your fingers or hands in the path of the sawblade orother cutting tool.
C. NEVER reach in back ofthe cutting tool with either hand to hold down or support the workpiece, remove wood scraps, orfor any other reason.
D. AvoU hand positions where a sudden sl;p could cause fingers or hand to move into a sawblade or other cutting tool.
E. DON'T OVERREACH. Always keep good footing and balance.
F. Push the workpiece against the rotation of the blade. NEVER feed material into the cutting tool from the rear of the saw.
G. Always push the workpiece all the way past the sawblade.
H. As much as possible, keep your face and body to one side of the sawblade,out of linewith apossible kickback or throwback.
L NEVERtumthesaw"ON"beforeclearingthetable of all tools, wood scraps, etc., except the workpiece and related feed or support devices for the cut planned.
WHENEVER SAW BLADE IS SPINNING second is enough to cause a severe Injury.
1. Before actually cutting with the saw, watch it while it runs for ashort while. If itmakes an unfamiliar noise or vibrates a lot, stop immediately. Turn the saw off.
Unplug the saw. Do not restart until finding and fixing the problem.
2. Make sL=rethe top of the arbor or cutting tool turns toward the front of the saw.
3. Set the cutting tool as low as possible for the cut you're planning.
4. KEEP CHILDREN AWAY, All visitors should be kept asafedistancefrornwork.
Make surebystanders are clear of the saw and workpiece.
5. Let the blade reach full speed before cutting.
6. DON'T FORCE TOOL.
It will do the job better and
saferat itsdesigned rate. Feed theworkpiece intothe
blade only fast enough to let it cut without bogging down or binding.
7. Before freeing any jammed material:
A. Turn switch "OFF",
B. Unplug the saw.
C. Wait for all moving parts to stop.
D. Check blade, Spreader and Fence for proper alignrnent before starting, again.
8. To avoid throwback of cut off pieces;
A, Use the Guard assembly.
B To remove loose pieces beneath or trapped inside the guard:
1. rum saw "OFF".
2. Remove switch key.
3. Wait for blade to stop before lifting the Guard.
ADDiTiONAL INSTRUCTIONS
RIPTYPE CUTS
FOR
1. NEVER use the Miter Gauge when ripping.
2. Use a Push Stick whenever the fence is 2 or more inches from the blade.
When thru sawing, use an
Auxiliary Fence and Push Block whenever the Fence must be between 1/2 and 2 inches ofthe blade. Never
thru saw ripcuts lessthan 1/2 inchwide. (See"BASIC
SAW OPERATION - USING THE RIP FENCE" section.)
3. Never rip anything shorter than 10" long.
4. When using a Push Stick or Push Block, the trailing
end of the board must be square. A Push Stick or
Block against an uneven end could slip off or pushthe
work away from the Fence.
5. A FEATHERBOARD can help guide the workpiece.
See "BASIC SAW OPERAT{ON - USING THE RIP
FENCE." Always use Featherboards for any non thru riptype cuts.
_...-------- 24"
KERFS ABOUT
5/16" APART
BEFORE STARTING
1. TO avoid kickbacks and slips into the blade, make sure the Rip Fence is parallel to the sawblade.
2. Check the anti-kickback pawls.
(See "BASIC SAW
OPERATION - USING THE RIP FENCE.") The
Pawls must stop a kickback once it has started.
Replace or sharpen Anti-Kickback Pawls when points become dull.
3. Plastic and composition (like hardboard) materials
may be cut on your saw.
However, since these are usually quite hard and slippery, the Anti-Kickback
Pawls may not stop a kickback.
Therefore, be especially careful in your set-up and cutting procedures.
WHILE CUTTING
1. To avoid kickbacks and slips into the blade, always push forward on the section of the wo rkpiece between the saw blade andthe Rip Fence. Never push forward on the piece being cut off.
ADDITIONAL iNSTRUCTIONS FOR
CROSSCUT TYPE CUTS
BEFORE STARTING
1. NEVER use the Rip Fence when crosscutting.
2. An auxiliary wood facing attached to the Miter Gauge can help prevent workpiece twisting and throwbacks.
Attach itto the holes provided.
Make the facing long
enough and big enough to support your work. Make sure, however, it will not interfere with the Sawblade
Guard.
(See page 26)
3.
Use jigs or fixtures to help hold any piece too small to
extend across the full length of the Miter Gauge face during the cut. This lets you properly hold the Miter
Gauge and workpiece and helps keep your hands away from the blade.
WHILE CUTTING
1. To avoid blade contact, always hold the Miter Gauge as shown in the "BASIC SAW OPERATIONS - US-
ING THE MITER GAUGE."
BEFORE LEAVING THE SAW
1. Turn the saw off.
2. Wait for blade to stop spinning.
3. Make workshop child-proof.
Lock the shop. Disconnect master switches.
Remove the yellow Switch
Key.
Store _ away from children and others not qualified to use the tool.
4.
Unplug the saw.
glossary of terms for woodworking
Anti-Kickback Pawls (AKP)
Device which, when properly maintained, is designed to
stop the workpiece from being kicked back at the opera-
tor during dpping operation.
Arbor
The shaft on which a cutting tool is mounted.
Crosscut
A cutting or shaping operation made across the width of the workpiece.
Dado
A non through cut which produces a square sided notch or trough in the workpiece.
Featherboard
A device which can help guide workpieces during rip type operation.
Freehand
Performing a cut without using a Fence, Miter Gauge, fixture, hold down or other proper device to keep the workpiece from twisting during the cut.
Gum
A sticky, sap based residue tram wood products.
Heel
Misalignment of the blade.
Kerr
The amount of material removed by the blade in a
through cut or the slot produced by the blade in a non
through or partial cut.
Kickback
An uncontrolled grabbing and throwing of the workpiece back toward the front of the saw.
Leading End
The end of the workpiece which, during a rip type operation, is pushed into the cutting tool first.
Molding
A non through cut which produces a special shape in the workpiece used for joining or decoration.
Push Stick
A device used to feed the workpiece through the saw during narrow ripping type operations and helps keep the operator's hands well away from the blade.
Push Block
A device used for ripping type operations too narrow to allow use of a Push Stick.
Rabbet
A notch in the edge of a workpiece.
Resin
A sticky, sap base substance that has hardened.
Ripping
A cutting operation along the length of the workpiece.
Revolutions Per Minute (RPM)
The number of turns completed by a spinning object in one minute.
glossary of terms for woodworking
Sawblade Path
The area ofthe workpiece or table top directly in linewith the part of the workpiece which will be, or has been, cut by the blade.
Set
The distance thatthe tip ofthe sawblade tooth isbent (or
set) outward from the face of the blade.
Throw-BaCk
Throwing of pieces in a manner similar to a kickback.
Thru-Sawing
Any cutting operation where the blade extends completely though the thickness of the workpiece.
Trailing End
The workpiece end last cut by the blade in a ripping operation.
Workpiece
The item on which the cutting operation is being done.
The surfaces of a workpiece are commonly referred to as faces, ends, and edges.
motor specifications and electrical requirements
occurs, there isthe potential of a secondary hazard,
This saw is designed to use a 3450 RPM motoronly.
Do not use any motor that runs faster than 3450 RPM. It is wired for operation on 120 volts. 60 Hz., alternating current.
IT MUST NOT BE CONVERTED TO OPER-
ATE ON 230 VOLTS.
CAUTION: Do not use blower or washing machine motors or any motor with an automatic reset overload protector as their use may be hazardous.
For replacement motor, refer to parts list in this manual, such as your hands contacting the sawblade.
This saw is equipped with a 3-conductor cord and
grounding type plug which has a grounding prong,
approved by UndenNriters' Laboratories and the Canadian Standards Association. The ground conductor has
a green lug and isattached to the tool housing at one end
and to the ground prong in the attachment plug at the other end.
This plug requires a mating 3-conductor grounding type
outlet as shown.
CONNECTING
OUTLET
TO POWER SOURCE
This saw must be grounded while in use to protect the
operator from electrical shock.
If the outlet you are planning to use for this saw is of the
two prong type, DO NOT REMOVE OR ALTER THE
GROUNDING PRONG IN ANY MANNER. Use an
adapter as shownbelow and always connect the ground- ing lug to a known ground.
Itpower cord isworn or cut, of damaged in any way, have it replaced immediately.
Your saw is wired for 120 volts and has a plug that looks like the one shown below.
It is recommended that you have a qualified electrician
replace the TWO prong outlet with a properly grounded
THREE prong outlet.
GROUNDING LUG
3-PRONG PLUG
3-PRONG
PLUG
I_
_'_ L _ _.-_=
_ :._
" l___ II
/
ADAPTER
MAKE SURE THIS
CONNECTED
KNOWN
TO
GROUND
A
IS
.EC,.T,C'E
Atemporary adapter, as shown, is available for connect- ing plugs to 2-prong receptacles.
The green grounding lug extending from the adapter must be connected to a perrnanent ground such asto a properly grounded outlet box. This adapter should be used only until a properly
If you are not sure that te plug can incur the plumbing,
NOTE: The adapter illustrated is for use only if you already have a properly grounded 2-prong receptacle.
The use of any extension cord will cause some loss of power.
To keep this to a minimum and to prevent
overheating and motor bum-out, use the following table
to determine the minimum wire size (A.W.G.) extension cord.
Use only 3 wire extension cords which have 3-prong
grounding type plugs and 3-prong receptacles which accept the plug on the saw.
1 H.P. MOTR 110 - 120V
Extension Cord
Length
0 - 25 Feet
26 - 50 Feet
51 - 100 Feet
Wire Size A.W.G.
No. 16
No. 14
No. 12
CHECK MOTOR ROTATION
The motor must rotate CLOCKWISE when viewed from the shaft end to which you wilt mount the pulley. (See page 21 .) If it does not, do not assemble or use saw until motor with right rotation is installed.
contents
Warranty ....................................................................
2
Safety instructions for Table Saw .......................... 2
Additional Instructionsfor Rip Type Cuts ............... 4
Additional Instructionsfor Cross Cut Type Cuts .... 5
Glossary ....................................................................
5
Motor Specifications and
Electrical Requirements ......................................
6
Connecting to Power Source Outlet ...................... 6
Motor Rotation .......................................................
7
Unpacking and Checking Contents ........................ 8
Tools Needed .........................................................
8
List of Loose Parts .................................................
8
Assembly ................................................................
10
Installing Handwheels ..........................................
10
Checking Table insert ..........................................
10
Checking Blade Squareness to Table ................. 10
Assembling Steel Legs ........................................
11
Mounting Saw ......................................................
11
Attaching and Assembling Table Extensions ....... 12
Mounting Switch ..................................................
13
Installing Right Front Rip Fence Guide Bar ......... 14
Installing Rear Fence Guide Bar .......................... 15
Aligning Rip Fence ...............................................
17
Self Aligning Spring Adjustment ..........................
17
Rip Fence Lock Lever Adjustment ....................... 18
Rip Fence Alignment Adjustment ........................ !8
Adjusting Rip Scale Pointer .................................
19 installing Blade Guard .........................................
19
Mounting the Motor ..............................................
21
Installing Belt Guard .............................................
23
Plugging in Motor .................................................
24
Getting to Know Your Saw ....................................
25
On.Off Switch .......................................................
25
Elevation Handwheel ...........................................
26
Tilt Handwheel .....................................................
26
Tilt Lock Handle ...................................................
26
Rip Fence .............................................................
26
Miter Gauge .........................................................
26
Blade Guard .........................................................
26
Table Insert ..........................................................
26
Removing and Installing Sawblade ...................... 27
Exact-I-Cut ...........................................................
27
Safety instructions for Basic Saw Operation ...... 28
Basic Saw Operation - Using the Miter Gauge .... 30
Work Helpers .......................................................
30
Crosscutting .........................................................
31
Repetitive Cutting ................................................
32
Miter Cutting .........................................................
32
Bevel Crosscutting ...............................................
33
Compound Miter Cutting ......................................
33
Using the Rip Fence ...............................................
33
Ripping ................................................................
34
Bevel Ripping .......................................................
34
Using Featherboards for Thru Sawing ................. 36
Resawing .............................................................
36
Cutting Panels .....................................................
37
Rabbeting ............................................................
37
Ploughing and Molding ........................................
37
Dadoing ................................................................
38
Molding Cutting ....................................................
38
Using Featherboards for Non Thru-Sawing ......... 38
Adjustments ...........................................................
39
Miter Gauge .........................................................
39
Heeling Adjustment or Parallelism of Sawblade
to Miter Gauge Groove ....................................
39
Blade Tilt, or Squareness of Blade to Table ........ 41
Tilt Mechanism .....................................................
42
Maintenance ...........................................................
Lubrication ..............................................................
43
43
Recommended Accessories .................................
43
Trouble Shooting ...................................................
44
Motor ....................................................................
44
Repair Parts ........ ....................................................
46
7
unpacking and checking contents
TOOLS NEEDED
Phillips Screwdriver
Medium Screwdriver
Small Screwdriver
COMBINATION SQUARE MUST BE TRUE.
STRAIGHT EDGE
DRAW LIGHT LINE ON
BOARD ALONG THIS EDGE, *_-,
3/4" THICK.
THIS
BE PERFECTLY
OF BOARD
EDGE MUST
STRAIGHT.
I
M
Combination Square SIZE
Sot Screw Wrenches
3/32 In.
118 in.
5/32 in.
Wrenches
7116 in.
112 In.
9/16 In.
Separate all parts from packing materials and check
each one with the illustratbn and the list of Loose Parts to make certain all items are accounted for, before discarding any packing material.
WARNING: If any parts are missing, do not attempt to assemblethe table saw, plug in the power cord or
turn the switch or= until the missing parts are obtained and are Installed correctly.
Remove the protective oilthat is applied to the table top and edgesof thetable. Use anyordinary household type grease and spot remover.
WARNING: Toavoidfireor health hazard, never use gasoline, naptha, or similar highly volatile solvents.
Apply a coat of automobile wax to the table.
Wipe all parts thoroughly with a clean, dry cloth.
WARNING: Foryour own safety, neverconnect plug
to power source outlet until a, assembly steps are complete, and you have read and understand the safety and operational Instructions.
SHOULD
HERE
OVER
BE NO GAP OR OVERLAP
WHEN SQUARE IS FLIPPED
IN DOTTED POSITION,
G
J
AM
F
K
L
N
0
P ffEM
E
H
M
A
B
C
D
Q
R
S
T
U
PART NAME QTY.
Blade Guard and Spreader ...........................
1
Rip Fence ......................................................
1
Owner's Manual ............................................
1
Cast Iron Table Extensions ........................... 2
Miter Gauge ..................................................
1
Rip Fence Guide Bar with Rip Scale (Front). 1
Support, Motor Base .....................................
1
Rip Fence Guide Bar (Rear) ......................... 1
Side Stiffener .................................................
2
Leg ................................................................
4
End Stiffener .................................................
2
Motor .............................................................
1
Bag of Loose Parts
(Containing the following items)
Outlet, On/Off with Key .................................
1
Handwheel ....................................................
2
Bracket, "L" Mounting (Model 113298721)...
1
Bag of Loose Parts ........................................
3
Bag of Loose Parts
(Containing the following items)
Wrench ..........................................................
1
Belt, "V" 1/2 x 41 ...........................................
1
Pulley, 1/2 dia. with 5/8 Bore ......................... 1
Spreader, Rod ...............................................
1
Blade Guard Support ....................................
1
Spreader Support ..........................................
1
(MODEL u
113.298761)
S
(MODEL 113.298721)
AA
AB
AC
AF
AA
AB
AB
AB
AC
AC
AF
AG
AH
AB AC AD
AJ_
AE AF
AK
0
AG AH
assembly
Before mountingthe saw on legs, a stand or a bench, the
Table Insert and Blade Squareness must be checked at this time.
INSTALLING HANDWHEELS
1. Line up FLAT SPOTS on shaft and Handwheel, push
Handwheel onto shaft. Install screw and Iockwasher to lock Handwheel on shaft.
ELEVATION
HANDWHEEL
CHECKING TABLE INSERT
1. Insert should be flush with table top, Check as shown. Loosen flat head screw that holds Insert and adjust the four set screws as necessary. -tighten flat head screw. Do not tighten screw to the point where
it deflects the Insert.
3/32 IN
SETSCREW WRENCH
2. To remove Insert.
A. Loosen Screw
B Lift Insert from front end, and pull toward front of saw,
3, To replaceinsert.
A. Place Insert into insert opening in table and push
toward rear of saw to engage spring clip and until
keyslot in insert will drop over screw. Tighten screw.
B. Do not tighten screw to the point where it will deflect the Insert.
LOCKWASHER
10-32 X 314 IN.
PHILLIPS
HEAD SCREW
TILT HANDWHEEL
CHECKING BLADE SQUARENESS TO
TABLE
IMPORTANT: BLADE must be SQUARE (90 °) to
TABLE, in order to proceed with assembly.
1. "rum Elevation Handwheelclockwise until blade isup
2. Check for BLADE SQUARENESS.
square to table, adjust it at this time,
If blade is not
Contents" section
Refer to "Blade Tilt, or Squareness of Blade to Table"
adjustment on page 39.
10
MAKESURESQUARE
ISNOTTOUCHING
TIPOFTOOTH
/
/
ASSEMBUNG STEEL LEGS
1. From among the loose parts, find the following hard- ware:
*24 Truss Head Screws, 1/4-20 x 1/2" long
*24 Lockwasher, 1/4 External
*24 Hex Nuts, 1/4-20
*8 Hex Nuts,318-16
*4 Leveling Feet
Items marked with an asterik (*) are shown actual size.
©
1/4 IN EXTERNAL
1/4-20 x 1/2 IN.
TRUSS HEAD SCREW
LOCKWASH ER
@
1/4-20
HEX NUT
3/8 - 16
HEX NUT LEVELING FOOT
2. Assemble the legs as shown.
Insert the Truss Head Screws through the holes in the legs, then through the holes in the Stiffeners. MAKE
SURE THE SCREWS GO THROUGH THE HOLES
IN THE SIDE STIFFENERS MARKED "X".
3. Install the lockwasher, screw on the nuts but do not tighten until completely assembled.
4. Install Leveling Feet.
ASSEMBLE SCREWS
THROUGH HOLES
MARKED "X"
SIDE STIFFENER
END
STIFFENER
_
\
HEX NUTS
LEVELING FOOT
MOUNTING SAW
1. From among the loose parts, find the following hardware.
*4 Hex Head Screws, 5/16-18 x 1-1/4" long
*4 Hex Nuts, 5/16-18
*4 Lockwasher, 5/16 External Type
*8 Flat Washers, 11/32 x 11/16 x 1/16
Items marked with an astenl_ (*) are shown actual size.
HEX HEAD SCREW 5/16-18
HEX NUT
5/16 IN EXTERNAL
LOCKWASHER
FLAT WASHER
11
assembly
2. Place saw on legs so that holes in bottom of saw line up with holes in top of legs.
3. Install screws, washers, Iockwashers and nuts as shown.
FLAT WASHER ..----_ _
!
END
FLAT WASHER -----'_
LOCKWASHER
STIFFENER'_ k
SAW BASE !
I i
/
If you mount the saw on any other bench, make sure that
there isan opening in the top ofthe bench the same size as the opening in the bottom of the saw so that the sawdust can drop through.
Recommended working
height is 33 to 37 inches from the top of the saw table to
the floor.
7/16 DIA. HOLES
T®
L
F
11-1/4
13
OPENING_
16 \
7_
13 t
/
\
\
ATTACHING AND ASSEMBLING
TABLE EXTENSIONS
1. From among the loose parts findthe following hardware: (Quantity indicated is for two extensions)
*8 Hex Hd. Screw 5/16-18 x 1-1/4
*8 Flat Washer
*8 External Lockwasher, 5/16
*8 Hex Nut, 5/16;18
Items marked with an asterik (*) are shown actual size.
2-3/4
NOTE: All dimensions in inches
G
5/16-18
HEX NUT
HEX HEAD SCREW
1t2
,5/16 IN EXTERNAL
LOCKWASHER FLAT WASHER
12
2. Insert four (4) 5/16-18 x 1-1/4 in. long screws through hole in each Extension.
3. Position extension against table so screws extend through hole in fable.
4. Install flat washers, Iockwashers, and nuts on the screws...
DO NOT TIGHTEN.
5. Line up the rear edge of extension with the rear edge of the table and top surface of the extension with the top of the table at the spots marked"X" in the drawing.
Use a combination square to line-up these edges.
SLIGHTLY TIGHTEN nuts with a 9/16" wrench.
1
SAW TABLE
(REF)
2
3
4
\
CHECK WITH SQUARE
AT 2 PLACES
MARKED WITH "X"
6. If adjustment is necessary you should tap the extension into position using a hammer and a block of wood.
Make sure the rear edge of extension is still lined up with the rear edge of the table. Then firmly tighten nuts.
7. Repeat steps 2 thru 6 to install the other extension.
/
/
MOUNTING SWITCH
1. From among loose parts find the following:
*2 Hex Head Screw 5/16-18 x 3/4
*2 Flatwashers, 21/64 x 5/8 x 1/16
*2 External Lockwashers, 5/16
*2 Hex Nuts, 5/16-18
Items marked with an asterik (*) are shown actual size.
13
5/16-18 x 3/4
HEX HEAD SCREW 2t/64 tN WASHER
5/16 IN
HEX NUT
5/16 IN EXTERNAL
LOCK WASHER
assembly
2. Insert two 3/4 inch screws though two flat washers then through holes in switch holes in switch.
3. Insert screws through holes eight and ten in front fence guide bar as illustrated.
4. Install two Iockwasher and nuts. Tighten nuts.
JAM NUT
5/16-18
•.u,_.,, "_,.._
LOCKWASHER
/8TH HOLE
J ".
IOTH HOLE
\ GUIDE BAR
FRONT FENCE
%%'--WASHER t
HEX HEAD SCREW
5/16-18 x 3/4 IN.
INSTALUNG RIGHT FRONT RiP FENCE
GUIDE BAR
1. From among the loose parts, find the following hardware;
*2 Hex Head Screws, 5/16-18 x 1-3/4
"1 Hex Head Screws, 5/16-18 x 3/4
*4 Lockwashers, 5/16 External Type
*4 Hex Nuts 5/16-18
*3 Spacers, 3/4 diameter x 1/2 long
"1 Hex Head Screw 5/16-18 x 1-1/4
*2 Flat Washers
5/8
x 1/16
1 Bracket
5/16-18 x 1-!/4 iN
HEX HEAD SCREW 5/16 IN EXTERNAL
LOCK WASHER
5/16 IN
HEX NUT
HEX HD. SCREW 5/16-18 x 3/4 IN
Items marked with an asterik (*) are shown actual size.
5/8 X 1/16 IN WASHER 3/4 IN, DIA. X 1/2 IN. .,_/
SPACER
BRACKET
II
2. Put the bracket against the right edge of the right extension so the bracket is lined up with the FIRST
hole near the front of the extension.
Insert a 3/4 long
screw through a flat washer, through top hole in the
bracket, and through the FIRST hole in the extension.
Install a Iockwasher and nut on the screw. Tighten the nutonly slightly.
HEX NU
EXTERNAL
LOCKWASHER HEX HEAD
SCREW
5116-18 x 3/4 IN
3. Lay Guide Bars on saw table.
NOTE: The various holes in the Bar allow them to be positioned on the saw and also makes them adapt-
able to other models.
4. Insert a 1-3t4 inch/ong screwthrough the THIRDhole
LEFT SIDE OF
FRONT GUIDE BAR
TTH HOLE
(GUIDE BAR I$ TO BE
TURNED END FOR END
3RD HOLE AFTER SCREWS ARE
INSTALLED)
5. Place spacers on screws.
\
SCREW
S/16-18 x 1-3/4 IN.
14
6. Turn front bar end for end and insert bolts through holes in middle and on right sides of front of saw table as illustrated.
Install Iockwashers and nuts.
DON'T
SCREW NUTS ON ALL THE WAY, just get them started on the screws.
7. Insert 1-1/4 long screwthough slot in bar that matches hole in bracket.
Install spacer, Iockwasher and nut.
DON'T SCREW NUTS ON ALL THE WAY, just get them started on the screws.
iNSTALLING
REAR FENCE GUIDE BAR
1.
From among the loose parts find the following:
1 Bracket
*2 Hex Head Screws 5/16-18 x 1
*2 Hex Head Screws 5/16-18 x 3/4
*4 Flat Washers 5/8 x 1116
*4 External Lockwashers 5/16
*4 Hex Nuts, 5/16-18
1 Rear Fence Guide Bar
Items marked with an asterik (*) are shown actual size.
5/16-18 x 1 IN
HEX HD. SCREW
5/16 IN
EXTERNAL
LOCKWASHER
5/16-18 x 3/4
HEx HEAD
SCREW
FLAT WASHER
5/16-18
HEX NUT
BRACKET
REAR FENCE GUIDE BAR
2. Put the bracket against the right rear edge of the right extension sothe bracket is lined up with the FOURTH hole near the rear of the extension (see illustration).
3. Insert one of the 3/4 inch long screws through a flat washer, through the bracket, and through the FOU RTH hole inthe extension.
Install a Iockwashe r and nut on the screw. Tighten the nut only slightly.
\
REAR OF
EXTENSION
4TH HOLE
IKET
WASHER
HEX NUT
EXTERNAL
LOCKWASH ER 5/16-18 x 3/4
HEX HEAD
SCREW
4. Lay rear fence guide bar on the right rear side of the saw table as illustrated (as viewed from rear of the saw).
Insert a 3/4 inch long screw through a flat washer and through the FIRST slot of the rear fence guide bar.
Insert a I inch long screw through a flat washer and through the FIFTH slot.
Insert a I inch
long screw through a flat washer and through the
SEVENTH slot.
5. Turn the fence guide bar end for end and inserttwo of the 1 inch long screwsthrough thetwo holes inthe left rear edge of the table.
Insert the other 3/4 inch long screw through the bracket. Instal] a tockwasher and nut on bolts. DO NOT SCREW NUTS ON ALL THE
WAY. just get them started on the screws.
15
7TH SLOT 5TH SLOT
HEX HEAD
SCREW
5/16-18 x 1 IN
BACK OF SAW
1ST SLOT
I
HEX HEAD
SCREW
5/16-18 x 3/4 IN,
assembly
6. Slide the Bars so that screwsare in the MIDDLE oft he slotted holes.
7. PositionRipFenceoverMiterGaugeGroove, holding up the rear end while engaging front end with Bar.
Lower Fence onto table.
8.
Raise blade all the way up.
9.
Carefully move Fence against blade.
10. Move Front Bar until "0" mark on Rip Scale is approximately in line with tip of Pointer.
11. Move Front Bar upwards until Fence is approxi-
mately 1/32 inch above table. l-_Jhten screw at left end of Bar.
NOTE: Fold a piece of newspaper making 8 thicknesses and place between Rip Fence and table to act as a spacer. This will hold the Fence off of the table approximately 1/32 inch.
12. Adjust Rear Bar so that the Fence is approximately
1/32 inch above table, make sure it is square with
Miter Gauge Groove. Tighten screw at end of Bar.
13. Move Fenceto RIGHTedge of table. Make sure it is approximately 1/32 inch above table at front and rear and tighten screws.
8THICKNESSES
OF PAPER
8 THICKNESSES
16
ALIGNING RiP FENCE
The Fence should slide easily alongthe Bare and always
remain in alignment (parallel to sawblade and Miter
Gauge Grooves).
The alignment is maintained by a spring underneath the
Fence which bears against the Front Guide Bar.
To move the Fence, loosen the Lock Handle and grasp the Fence with one hand at the trent.
For very close adjustments, grasp the Guide Bar with both hands and move the Fence with your thumbs.
"_"
SELF ALIGNING SPRING ADJUSTMENT
Place Fence on saw but DO NOT LOCK IT.
Move the REAR END of the Fence slightlyto the right or
left. When you release it, the Fence should=spring" back
to its original position.
If itdoes not, the spring pressure must be INCREASED.
1. Loosen the screws.
2. Move spring slightly toward front of Fence. Tighten screws.
/
17
\
assembly
If the Fence does not slide easily along the Bars, the pressure of the spring can be REDUCED.
1. Loosen the screws.
2. Move spring slightly toward rear of Fence. Tighten screws.
WARNING: Toavoid Injury from jarnsorklckbacks, be sure to push properly adjusted Lock Lever all the
way down until the lever rests on the stop before using the Rip Fence.
SPRING
SLIDE SPRING TO
ADJUST PRESSURE
ADJUSTING NUT
FENCE HEAD
RiP FENCE LOCK LEVER ADJUSTMENT
The Rip Fence Lock Lever, when locked down, should
hold the Rip Fence securely, it should not be difficultto
push down and lock.
If Lock Lever does not lock fence securely:
1. Raise Lock Lever.
2. Tighten the adjusting nut using a small screwdriver until the lever, when locked, holds the Rip Fence securely.
If Lock Lever is difficult to push down:
1. Raise Lock Lever.
2. Loosen the adjusting nut using a small screwdriver until the lever is easy to push down and holds the Rip
Fence securely.
RiP FENCE ALIGNMENT ADJUSTMENT
1. The Rip Fence must be PARALLEL with the sawblade and Miter Gauge Grooves.
Move Fence until it is along side of Groove. DO NOT LOCK IT. It should be parallel to Groove.
ff it is not;
A. Loosen the two Hex Hd. Screws.
B. Hold Fence head tightly against Bar. Move end of
Fence so that it is parallel with Groove.
C. Alternately tighten the screws.
D. Recheck alignment.
E. Repeat steps as needed.
WARNING: A misallgned fence can cause kickbacks and jams. To avoid Injury, follow these irv
structlons until the fence is properly aligned.
18
HEXSCREWS
FENCE HEAD
ADJUSTING RiP SCALE POINTER
1. Turn Elevation Handwheel clockwise until blade is up as high as it will go.
IMPORTANT: BLADE must be SQUARE (90°) to
TABLE, in order to ALIGN Rip Scale.
2. Position Fence on right side of sawblade so that it touches the sides of the teeth, tighten Lock Handle.
3. Loosen screw holding the Pointer, adjust so that it points to "0" on the Rip Scale, tighten screw.
NOTE: If you cannot adjust Pointer so that it points to
"0", loosen the screws holding the Front Guide Bar and move the Guide Bar.
LOCK HANDLE
INSTALLING BLADE GUARD
1. From among the loose parts, find:
*2 Hex Head Screws, 1/4-20 x 5/8
*3 Hex Head Screws, 5/16-18 x 5!8
@
1/4-20
HEX NUT
*2 Hex Head Screws, 5/16-18 x 1
*2 Hex Nuts, 1/4-20
*2 Lockwashers, 1/4 Extemal Type
Q
*2 Lockwashers, 5/16 ExternalType
"1 Thumbscrew
1 Blade Guard Support
_161N.
1 Spreader Support
EXTERNAL
LOCKWASHER
1 Spreader Rod
Items marked with an astedk (*) are shown actual size.
©
1/4 IN.
EXTERNAL
LOCKWASH ER
BLADE GUARD
SUPPPORT
THUMBSCREW
1/4-20 X 5/8 IN.
HEX HD. SCREW 5/16-18 X 5/8 IN.
HEX HD. SCREW
5/16-18 X 1 IN.
, HEX HD. SCREW SPREADER SUPPORT
SPREADER ROD
2. Before installing the Blade Guard, you must check
the heeling adjustment (parallelism of sawblade to
Miter Gauge Groove). The procedure for making this check and adjusting it are found in the "ADJUST-
MENTS" secion of this manual. Refer to "HEELING
ADJUSTMENTOR PARALLELISM OF SAW BLADE
TO MITER GAUGE GROOVE."
3. Lower the blade.
4. Screw the Motor Base Clamp Screws part way into
cradle. Screw the 5/16-18 x 5/8 inch Hex Hd. screw into the Blade Guard Support.
5. Attach Blade Guard Support.
DO NOT TIGHTEN
SCREWS.
BLADE (
SUPPORT
\
5/16-18 X
5/8 IN.
HEX HD.
SCREW
5/16.18X1
IN.
]
HEX HD. SCREWS
5116-18 X 5/8 IN
HEX HD. SCREWS
19
assemb|y
6. Insert Spreader Rod into Spreader Support until pin
fits into notch.
Insert Thumbscrew and tighten it.
THUMB SCREW
\
\
SPREADER
ROD
\
\
FLAT
SURFACE
\ (INTO SUPPORT)
17 "
U
SPREADER
SUPPORT
7. Slide Spreader Rod into Blade Guard Support until
end of Rod is even with edge of Support. Tighten
Hex Head Screw in Support.
8. Attach Spreader to Spreader Support so that the edge of the Spreader is ever_with the edge of the
Spreader Support. Tighten screws.
9. Raise Anti-Kickback Pawls (hold in place with a setscrew wrench - see below). AlignSpreader SQUARE to table,
Tighten both 5/16-18 x 1 inch Hex Head Screws.
1/-2ONE\
HD. SCREW
I II II _L-""-.-.._
___\
114 IN. LOCKWASHER _ II I.j'_Trr'"
,,,-,O.EX.UT
SPREADER EDGE f I II "_.%'_
EVEN WITH SPREADER I U _h_'_
EmDOFROD
EVEN WiTH EDGE
- _
I_'__
\ /l_";)
'/I
, _t_J
\/_--II
_J/.i/"
\\ v_l
\\ \\ _1
I t
I
I
,J,/_-'<'-"_---_A\ I I
_ _._=1 _ _.._._
I [
10. Raise blade all the way up, make sure it is square with table.
11. Raise Blade Guard.
Lift up both Anti-Kickback
Pawls. Insert one of the Setscrew Wrenches in the notches to hold the Pawlsout of the way.
13.Loosen Hex Head Screw in Guard Support and move Spreader so that it touches blade of square.
Tighten screw.
HE\ HD.
SCREW
KERF WOOD
15.IMPORTANT: To work properly, the Spreader must always be PARALLEL to the sawblade and adjusted so the cut workplece will pass on either side at the Spreader without binding or skewing to the side.
NOTE: The Spreader is thinner than the width of the cut (KERF) by approximately six thicknesses of paper.
SPREADER ..__ -.
....
LOOKING DOWN ON SAW
16. Make two folds in a small piece (6 x 6 inch)of ordinary
NEWSPAPER making three thicknesses.
The folded paper will be used as a "spacing gauge".
/
17.Place
RipFence on table, CAREFULLY move it against blade so that it is parallel to the blade, and just TOUCHEStips of sawteeth.
Tighten Rip Fence
Lock Lever.
18. Insert folded paper between Spreader and Fence.
19.Using
7/16 wrench loosen the 1/4-20 hex head screws so the Spreader can slide sideways.
20. Hold Spreader flat against Fence.
Tighten screws using 7/16 inch wrench.
21.To
remove Blade Guard and Spreader, loosen
Thumbscrew. DO NOT LOOSEN OTHER SCREWS.
This lets you remove and replace the Guard without disturbing the Spreader alignment.
7/16IN. WRENCH
FOLDED PAPER
MOUNTING THE MOTOR
Model 113.298721 & 113.298761
Check Motor Rotation
1. The Motor must rotate CLOCKWISE when viewed from the 5/8 inch shaft.
2. MAKE SURE "KEY' IS REMOVED FROM SHAFT.
3. Place the Motor on your workbench or on the floor.
4. Plug the cord into a properly grounded outlet (See
"MOTOR SPECIFICATIONS AND ELECTRICAL
REQUIREMENTS" section) Notice the rotation of the shaft. If it is not turning CLOCKWISE, do not assemble or attempt to operate saw until motor with correct rotation is obtained,
21
KEY
518 IN.
DIA, SHAFT
TION
assembly
5. From among the loose parts, find the following hardware:
*4 Carriage Bolts, 5/16-18 x 3/4
*4 Hex Nuts 5t16-18
*4 Lockwashers, 5/16 External Type
1 Motor Pulley
1 Belt Guard "L" Bracket
1 Belt Guard Support Bracket
Items marked with an asterisk (*) are shown actual size.
BELTGUARD
"L_BRACKET
5/16-18 x 3/4 IN
CARRIAGE BOLT
= == i i , i=
POSITIONING MOTOR ON MOTOR MOUNTING
BASE
Model 113.298761
,1=
1. Put the motor mounting base against the flat surface of a workbench.
2. Positionthe motor so the end with terminal cover is facing you.
3. Loosen both cradle clamp screws.
4. Put a square against the LEFT side of the motor and against the top of the workbench.
5. Turn the motor inside the cradle clamps until the top
of both capacitors touch the square
6. Tighten bothcradle clamp screwsIo hold the motor in this position.
WARNING: Failure to properly Install motor may let workplece strike capacitor cover during bevel or
=l compound miter cuts.
MOUNTING MOTOR ON MOTOR BASE
Model 113.298721 & 113.298761
1. Place Motoron MotorBase so that shaft is pointing
to the right. Insert bolts through holes in Base, then through the Motor MountingBase. Installlockwashers and nuts, DO NOT TIGHTEN AT THIS TIME.
2. Position Motor so that edge of Motor Foot and Motor
Base are even. Slide Motor allthe way to the RIGHT.
Slip the long part of the "L" Bracket fully under the
Motor so the short part is just under shaft (Model
113.298721 only). Tighten the fournuts.
_ BELT GUARdeD
MOTOR SUPPORT BRACKET
PULLEY
WELDED MOTOR
MOUNTING BASE
THESE TWO
EDGES EVEN
LOCKWASHER
5/16 IN.
CARRIAGE BOLT
5116-18 X 3/4 iN.
5/16-18
5/16-18
HEX NUT
5/16 IN EXTERNAL
LOCKWASHER
LOOSEN BOTH CRADLE CLAMP SCREWS r.---
CAPACITORS"
SQUARE
MOTOR
MOTOR MOUNTING
BASE
WORK BENCH away from Motor. DO NOTTIGHTEN SETSCREW.
4. Install 3116 inchsquare key (furnished with Motor) in groovesin PulleyandMotorshaft. DONOTTIGHTEN
SETSCREW.
, = =
INSTALUNG BELT
Model 113.298721
& 113.298761
1. Lift Motor and insert the TWO PINS on Motor Base
into HOLES in Cradle. Push Motor in as far as itwill go.
22
BELT GUARD SUPPORT
INSERTED EVEN WITH
MOTOR END HUB
"" PULLEY
2. Lowerthe blade, install Belt on Saw Pulley and Motor
Pulley.
3. Sight along edges of both pulleys and move Motor
Pulley so that belt is parallel to the edges of bol
Pulleys.
Tighten the set screw in the Motor Pulley.
4. iMPORTANT:
distance from end of
Motor shaftto Pulley, Mark this dimension down; you will need it later when reinstalling the Pulley.
5. Make sure blade is 90°totable, raise it allthe way up.
6. Lift Motor untiledge ofwasher isevenwith end of slot tighten pivotscrew. Inthis position, pull Motor toward you (pins will slide out of Cradle) until Belt is TIGHT,
tighten the two Motor Base Clamp Screws.
EDGE OF WASHER
EVEN WITH END
OF SLOT
7. Loosen Pivot Screw slightly.
8. Lower the saw blade all the way down.
9. iMPORTANT: Motor should pivot freely down-
ward as blade is lowered. If it does not, LOOSEN the Pivot Screw some more.
10. Pivot Screw must be adjusted only tight enough to allow Motor to pivot FREELY as blade is raised and lowered. This will maintain constant tension on Belt.
11. Put your hand around the belt half way between the
two Pulleys and squeeze Belt until two sides of Belt touch, The Motorshould move freely as you squeeze the Belt. If Motor does not move freely, Belt tension must be readjusted.
=
INSTALUNG BELT GUARD
Model 113.298721
1. Remove the Belt and Motor Pulley.
2. Screws furnished with Guard are "Self Threading".
Screwthem into holesin BeltGuard SupportBracket, then remove them.
3. Position Belt Guard Support Bracket and Belt Guard
Support as shown and install the screws. Make sure
Motor shaft is in CENTER of hole in Support.
BELT
"L"
GUARD
BRACKET
SCREW
/
"L"BRACKET
MOTOR PULLEY
TWO HOLES
TOGETHER
CLOSEST
BELT GUARD
SUPPORT k MOTOR BASE
CLAMP SCREWS_
PIVOT
-SCREW
BELT GUARD SUPPORT
INSTALLING BELT GUARD
Model 113.298761
SELF-THRSADING
SCREW
1. Remove the Belt and Motor Pulley.
2. Screws furnished with Guard are Serf Threading."
Screw them into holes in Belt Guard Support Bracket, then remove them,
3. Position Belt Guard Support Bracket and Belt Guard
Support as shown and install the screws. Make sure
Motor Shaft is in CENTER of hole in support.
'1 TWO HOLES CLOSEST
TOGETHER
BELT GUARD
SUPPORT BRACKET
BELT GUARD SUPPORT
BELT GUARD
/
CENTERED
\
PIVOT
SCREW
OPENING
assembly
iNSTALLiNG BELT GUARD
Model 113.298721 & 113.298761
1. install three Clips (furnished with Guard) 90° apart starting with one Clip at the end of the Guard as shown. LONG END of Clip facing AWAY from you.
2. Reinstall Motor Pulley the same way it waswhen you aligned the Belt,
3. Place Belt on Saw Pulley. Insert end of Bell through opening in END of Guard.
4. Slip Belt over Motor Pulley.
BELT GUARD
_
BELT
N
LONG END
CLIPS
5. Press Guard onto Support sothat bottom of Guard is
approximately 3/4 inch away from Belt.
NOTE: To remove Guard, lift up on LONG TABS of
Clips, pull Guard outward. The Clips should remain on the Belt guard Support.
3/4 iN.
PLUGGING iN MOTOR
1. From among the loose parts find:
2 Wire Ties
2. Route Motor Cord along dghtside ofcabinet and snap
ties in 1/4 inch bole in side of cabinet. Secure cord in wire ties,
3. Plug Motor cord into outlet on side of switch box.
24
EXTENSION REMOVED FOR
PICTURE CLARITY
WIRE TIES
getting to know your saw
9 SAWBLADE
J 7 BLADE GUARD
S TABLE INSERT
|0 EXACT-I-CUT ANTIKICKBACK
PAWLS
6 MITER GAUGE
RiP FENCE
HOLES;
ATTACHING
FOR
FACING
RiP FENCE
LOCK HANDLE
4 TILT LOCK HANDLE
(UNDERNEATH TABLE)
2 ELEVATION HANDWHEEL
1 ON-OFF SWITCH
ON-OFF SWITCH
CAUTION: Before turning switch "ON", make sure the blade guard Is correctly Installed and operaUng properly.
The On-Off Switch has a locking feature.
THIS
FEATURE IS INTENDED TO PREVENT UN-
AUTHORIZEDAND POSSIBLE HAZARDOUS USE
BY CHILDREN AND OTHERS.
A. To turn saw ON, stand to either side ot the blade,
never in line with it, insert finger under switch lever and pull END of lever out.
After turning switch ON, always allow the blade to come up to full speed before cutting.
Do not cycle the Motor Switch on and oft rapidly, as this may cause the sawblade to loosen. In the event this should ever occur, allow the sawblade to come to a complete stop and retighten the
arbor nut normally, not excessively. Never leave
the saw while the power in =ON",
B. Totum saw OFF, PUSH leverin. Never leave the saw untilthe cutting tool has come to a complete stop.
C. To lock switch in OFF position, hold switch IN with one hand, REMOVE key with other hand.
WARNING: For your own safety, lower blade or other cutting tool below table surface.
(If blade
Is Ulted. return It to vertical, 90 °, position). Always lock the switch "OFF". When saw Is not in use, remove key and keep it in a safe place. Also, in
the event of a power failure (all ofyour,ghts go out) turn switch off, lock It and remove the key.
This will prevent the saw from starting up again when the power comes back on,
25
3
TiLT HANDWHEEL
(YELLOW
KEY
PLASTIC)
getting to know your saw
2
3
4
5
ELEVATION HANDWHEEL ...
elevates or
Iowersthe blade, Turnclockwiseto elevate, counterclockwise to lower.
TILT HANDWHEEL...tilts
the blade for bevel cutting. Turn clockwise to tilt toward left, counterclockwise to tilt toward dght.
When the blade is tilted to the LEFT as far as itwill go, it should be at 45" to the table and the bevel pointer should point 45 °.
NOTE: There are LIMIT STOPS inside the saw
which prevent the blade from tilting beyond 45 ° to the LEFT and 90° to the RIGHT.
( See "ADJUST-
MENT,<;AND ALIGNMENTS"section"BLADE TILT,
OR SQUARENESS OF BLADE TO TABLE").
TILT LOCK HANDLE...
locks the blade inthe desired tilt position. To loosen, turn counterclockwise. Push handle in and turn it to another position if necessary in order to tighten or loosen.
RIP FENCE...
islocked in place by pushing the
Lock Lever down until the lever rests on the stop. To move the Fence, lift the Lock Lever and grasp the
Fence with one hand at the front.
Holes are provided in the Rip Fence for attaching a wood facing when using the Dado Head, or Molding
Head.
Select a piece of smooth straight wood approxi-
mately 3/4 inch thick, and the same size as the Rip
Fence.
Attach it to the Fence with three Round Head #10
Wood Screws, 2 inches long. TO removethe facing,
loosen the screws, slide the facing forward and pull the screws through the round holes.
WOOD FACING t
If necessary, the Miter Gauge head can then be
swiveled slightlyto compensate and then locked.
Slots are provided in the Miter Gauge for attaching an Auxiliary Facing to make it easier to cut long
pieces. Be positive Facing does not interfere with
the proper operation of the Sawblade Guard.
Select a suitable piece of smooth straight wood, ddll two holes through it and attach it with screws.
NOTE: When bevel crosscutting, attach Facing so that it extendsto the dght of the Miter Gauge and use the Miter Gauge in the groove to the righl of the blade.
FACING
STb.PI.
+s+soT \
FO.STO..,.
I I-
7
BLADEGUARD...must
always be in place and working properly for all thru-sawing cuts. That is, all
cuts where the blade cuts completely through the workpiece.
To remove the Guard for special operations, loosen the Thumbscrew and slide the Guard off of the Rod.
DO NOT DISTURB THE SETTING OF THE ROD.
When replacing the Guard, make sure the PIN inthe
Rod engages with the NOTCH in the Spreader
Support. Make sure Thumbscrew is tightened securely.
8 TABLE INSERT...
is removable for removing or installing blades or other cutting tools.
\
\
6 MITER GAUGE .., headislockedin positionfor crosscutting or rnitedng by tighteningthe Lock Knob.
ALWAYS LOCK IT SECURELY WHEN IN USE.
/
SCREW
Gauge to cut miters.
NOTE: The slots for the Stop Pin and the gradu-
ations are manufactured to very close tolerances
which provide accuracy for average woodworking.
In some cases where extreme accuracy is required, when making angle cuts. forexample, make a trial
cut and then recheck it.
26
A, Lower the blade below the table surface.
B.
F_aiseBlade Guard.
C.
Loosen screw.
D.
Lift insert from front end, and pull toward front of saw.
NEVER OPERATE THE SAW WITHOUT THE
PROPER INSERT IN PLACE.
USE THE SAW-
BLADE INSERT WHEN SAWING.
USE THE
COMBINATION DADO MOLDING INSERT WHEN
USING A DADO OR MOLDING HEAD.
REMOVING AND iNSTALLiNG
SAWBLADE
WARNING: For your own safety, turn switch
"OFF"and remove plug from power sourceoutlet before removing or installing sawblade.
A. Raise Blade Guard, remove Insert.
B; TO REMOVE Blade, place a blockofwood against front of Blade, PULL arbor wrench toward you to
LOOSEN arbor nut.
C. To TIGHTEN arbor nut, place a block of wood against rear of Blade, PUSH wrench away from you.
WOOD BLOCK
NUT
BLADE GUARD NOT SHOWN
FOR PICTURE CLARITY
BLADE GUARD NOT SHOWN
PICTURE CLARIFY
When installingthe Blade, make sure the teeth are pointing toward the front of the saw and that the
Blade and Collars are clean, and free from any burrs.
The HOLLOW side of the collar must be against the
Blade.
Always tighten the arbor nut securely.
NOTE: When using the Dado or Molding Head, it is not necessary to install the loose Collar.
To replace insert.
Place insert into opening in table and push toward rear of saw to engage Spring Clip and until keyslot in insert will drop over screw. Tighten screw.
Do not tighten screw to the point where itwill deflect the insert.
ICH
OR NUT
LOOSE
COLLAR
TEETH POINTING
ARBOR
<3 ._ _'
._
,_.._
_ :\ ARBORI NUT
, _.:?__._
FRONT OF SAW
TO ---._,
10 EXACT-I-CUT
The "yellow" Plastic Disc imbedded in the table En front of the sawblade, is provided for marking the location of the 'sawcut" on the workpiece.
A. Check Disc. If it is above table surface, place a
piece of hardwood on top of it and tap it down.
B. With blade 90 ° (square to table) cross cut a piece of wood.
C. Pull Miter Gauge back until wood is over Disc.
Using a sharp pencil, mark a line on Disc.
D. With Miter Gauge in fight hand groove, follow
same procedure and mark another line on Disc.
E. These lines indicate the -path" of the cut (ken')
made by the sawblade.
F. When cutting the workpiece, line up mark on
workpiece with line on Disc.
BLADE GUARD NOT SHOWN
FOR PICTURE CLARITY
27
safety instructions for basic saw operations
BEFORE EACH USE:
1. Inspect your saw.
A. To avoid injuryfrom accidental starting, unplug the saw, turn the switch off and remove the Switch Key before raising or removing the Guard, changing the cutting tool, changing the setup or adjusting anything.
B. Check for alignment of moving pads, binding of moving pads, breakage of pads, mounting, and
any other conditions that may affect the way it works. If any part is missing, bent, or broken in any way, or any electrical parts don't work properly, turn the saw off and unplug the saw.
C. Replace damaged, missing, or failed parts before using the saw again.
D. Use the Sawblade Guard, Spreader, and Anti-
Kickback Pawls for any thin-sawing (whenever the blade comes through the top of the workpiece).
Make sure the Pawlswork properly. Makesurethe
Spreader is in line with the sawblade.
E. REMOVE ADJUSTING KEYS AND WRENCH ES.
Form habit of checking for and removing keys and adjusting wrenches from tool before turning it on.
F. To avoid injury from jams, slips or thrown pieces
(kickback and throwback):
1. USE ONLY RECOMMENDED ACCESSORIES
(See page 44).
Follow the instructions that come with the accessories. Using other accessories may be dangerous.
2. Choose"the right blade or cutting accessory for the material and the type of cutting you plan to do.
3. Never use grinding wheels, abrasive cut-off wheels, friction wheels (metal slitting blades)
wire wheels or buffing wheel. Theycan fly apart explosively.
4. Choose and inspect your cutting tool carefully.
a. To avoid cuttingtoolfailure and thrown shrapnel (broken pieces of blade), use only 10" or
smaller blades or other cutting tools marked for speeds of 3450 rpm or higher.
b. Always use unbroken, balanced blades designed to fit this saw's 5t8 inch arbor.
c. When thru-sawing (making cuts where the blade comes through the workpiece top), always use a t 0 inch diameter blade.
This keeps the Spreader in closest to the bade.
d. Donor overtighten arbor nuL Use arbor enches to snug it securely.
e; Use onlysharp blades with properly set teeth,
Consult aprofessionalblade sharpenerwhen in doubt, f. Keep blades clean of gum and resin,
5. Adjust table inserts flush with the table top.
NEVER use the saw without the proper insert.
6. Make sure all clamps and locks are tight and no parts have any excessive play.
2. Keep work area clean
A. Cluttered areas and benches invite accidents.
Floor must not be slippery from wax or sawdust.
B. To avoid burns orother fire damage, never use the saw near flammable liquids, vapors or gases.
C. To avoid injury frorn accidental blade contact, don't do layout, assembly, or setup work on the table
while the blade is spinning.
It could cut or throw anything hitting the blade.
Plan aheadto protect your eyes, hands, face, ears.
AVOID ACCIDENTAL STARTING - Make sure switch is "OFF" before plugging saw in.
3. Plan your work
A. USE THE RIGHT TOOL - Don't force tool or attachment to do a job it was not designed for.
B. Dress for safety:
1. Do not wear loose clothing, gloves, neckties or
jewelry (rings, wristwatches).
They can get
caught and draw you into moving pads.
2. Wear nonslip footwear.
3, Tie back long hair.
4. Roll long sleeves above the elbow.
5. Noise levels vary widely.
To avoid possible head ng damage, wear ear plugs or muffs when
using saw for long periods of time.
6.
Any power saw can throw foreign objects into the eyes.
This can cause permanent eye damage.
Wear safety goggles (not glasses) that comply with ANSI Z87.1 (shown on package).
Everyday eyeglasses have only impact resistant lenses. They are not safety glasses.
Safety goggles are available at Sears retail
catalog stores. Glasses or goggles not in compliance with ANSI Z87.1 could seriously hurt
you when they break.
JR
7. For dusty operations, wear a dust mask along with t he safety goggles.
C. Inspect your workpiece. Make sure there are no
nails or foreign objects in the part of the workpiece
to be cut.
28
D. Plan your cut to avoid KICKBACKS and THROW-
BACKS - when a part or all of the workpiece binds
on the blade and is thrown violently back toward
the front of the saw. f. Never cut FREEHAND: Always use either a
Rip Fence, Miter Gauge or fixture to position and guide the work, so it won't twist, bind on the blade and kickback.
2. Make sure there's no debris between the work-
piece and its supports.
3. Whencutting irregularlyshapedworkpieces, plan your work so it will not slip and pinch the blade:
a. A piece of molding, for example, must lie flat
or be held by a fixture or jig that will not let it twist, rock or slip while being cut. Use jigs or fixtures where needed to prevent workpiece shifting.
b. Use a different, better suited type of tool for work that can't be made stable.
4. Use extra caution with large, very small or awkward workpieces:
a. Use extra supports (tables, saw horses
blocks, etc.) for any workpieces large enough to tip when not held down to the table top.
NEVER useanother person as a substitute for a Table Extension, or as additional support for a workpiece that is longer or wider
than the basic saw table, or to help feed, support or pull the workpiece.
b. Neverconfinethepiecebeingcutoff.
That is, the piece NOT againstthe Fence, MiterGauge
or fixture. Never hold it, clamp it, touch it, or
use length stops against it. It must be free to move. Ifconfined, itcouldgetwedged against
the blade and cause a kickback or throw- back.
c. Never cut more than one workpiece at a time.
d. Never turn your table saw "ON" before clear-
ing everything except the workpiece and
related support devices off the table.
4. Planthewayyouwill pushtheworkplecethrough.
A. NEVER pug the workpiece through.
Start and
finish the cut from the front of the table saw.
B. NEVER put your fingers or hands in the path of the sawblade or other cutting tool.
C. NEVER reach in back of the cuttingtoolwith either hand to hold-down or support the workpiece, remove wood scraps, or for any other reason.
D. Avoid awkward operations and hand positions
where a sudden slip could cause fingers or hand to move into a sawblade or other cutting tool.
E. DONq" OVERREACH.
Always keep good footing and balance.
F. Push the workpiece against the rotation of the blade.
NEVER feed material into the cutting tool from the rear of the saw.
G.Always
push the workpiece all the way past the sawblade.
H. As much as possible, keep your face and body to one side of the sawblade, out of line with a possible kickback or throwback.
I. NEVER turn the saw"ON"before clearing the table of all tools, wood scraps, etc., except the workpiece and related feed or support devices for the cut planned.
WHENEVER SAW
BLADE IS
SPINNING
WARNING: Don't let familiarity (gained from fre-
quent use of your table saw) cause a careless mis-
take. Always remember that a careless fraction of a
second is enough to cause a severe injury.
1. Before actually cutting with the saw, watch it while it runs for a short while. If it makes an unfamiliar noise or vibrates a lot, stop immediately.
Turn the saw off.
Unplugthe saw. Do not restart untiltinding andfixing the problem.
2. Make sure the top of the arbor or cutting tool turns toward the front of the saw.
3. Set the cutting tool as low as possible for the cut you're planning.
4. KEEP CHILDREN AWAY. All visitors should be kept a safe distance from work. Make sure bystanders are clear of the saw and workpiece.
5. Let the blade reach full speed before cutting.
6. DON'T FORCE TOOL.
It will do the ._obbetter and safer at its designed rate. Feed the workpiece intothe blade only fast enough to let it cut without bogging down or binding.
7. Before freeing any jammed material:
A. Turn switch "OFF".
B. Unplug the saw.
C. Wait for all moving parts to stop.
D. Checkblade, Spreader and Fence for proper alignment before starting, again.
8. To avoid throwback of cut off pieces;
A. Use the Guard Assembly.
B. To remove loose pieces beneath or trapped inside the Guard:
1; Turn saw "OFF".
2. Remove Switch Key.
3. Wait for blade to stop before lifting the Guard.
29
safety for basic saw operations
BEFORE LEAVING THE SAW
1. Turn the saw off,
2. Wait for blade to stop spinning.
3. Make workshop child-proof. Lock the shop. Disconi nect master switches.
Remove the yellow Switch
Key.
Store it away from children and others not qualified to use the tool.
4. Unplug the saw.
i,,i
basic saw operation - using the miter gauge
CROSSCUTTING, MITER CUTTING, BEVEL CUT-
TING, COMPOUND MITER CUI-rlNG and when RAB-
BETING across the end of a narrow workpiece, the
MITER GAUGE IS USED.
WARNING: For your own safety, aNvays observe the following safety precautions in addition to the safety instructions on pages 2, 3, 4, 5, 28, 29 & 30.
2.
3.
An auxiliarywood facing attached to the Miter Gauge
can help preventworkpiece twisting and throwback s.
Attach it to the holes provided. Make the facing long
enough and big enough to support yourwork. Make sure, however, itwill not interfere with the sawblade guard.
ADDITIONAL SAFETY INSTRUCTIONS
CROSS CUT TYPE CUTS
FOR
Use jigs or fixtures to help hold any piece too small
to extend across the full length of the Miter Gauge face during the cut. This lets you properly hold the
Miter Gauge and workpiece and helps keep your
hands away from the blade.
Before S_rting:
1. Never use the Rip Fence when crosscutting,
While Cutting:
1. To avoid blade contact, always hold the Miter Gauge
as shown in the "BASIC SAW OPERATIONS -
USING THE MITER GAUGE." i iii
WORK HELPERS
SLIGHTLY LESS THAN
THICKNESS OF WORKPIECE uP TO 3/8"
%.
-'F--'C 1/2_
1-5/8 _' i </\
_
Before cutting any wood on your saw, study all of the
"Basic Saw Operations."
Notice that in order to make some of the cuts, it is
necessary to use certain devices, "Work Helpers", like the Push Stick, the Push Blockandthe Auxiliary Fence/
Work Support, which you can make yourself.
After you have made afew practice cuts, make up these
"helpers"before starting any projects. Make the "Push
Stick" first.
45 ° NOTCH
NOTE: All dimensions in inches
PUSH STICK
THESE EDGES MUST
BE PARALLEL
PUSH STICK AND PUSH BLOCK
Make the Push Stick using a piece of 1 x 2.
Make the Push Blockusing a piece of 3/8 in. and 3/4 in.
plywood.
The small piece of wood 3/8 x 3/8 x 1-1!2 inches should be GLUED tothe plywood. DO NOT USE NAILS. This is to prevent dulling the sawblade in the event you mistakenly cut intothe Push Block.
Position the handle in the center of the plywood and fastentogetherwith glue and woodscrews.
AUXILIARY FENCE/WORK SUPPOFIT
3/8
\
5-1/8 3/8
NOTE: All dimensions in inches
FUSH BLOCK
3/4 PLYWOOD
3/8 PLYWOOD
NOTE: Since the Push BloCkis used with the Auxiliary
Fence, the 4-3/4 inches dimensions must be held iden- tical on both the pieces.
3O
NOTE
AUXILIARY FENCE/WORK SUPPORT
5-,1!2
.YWOOD
AUXILIARY PANEL WORK SUPPORT
Make using a piece of 3/4" and 3/8" plywood.
Fasten
together wtih glue and wood screws. Use this Auxiliary
Panel Work Support only when cutting large panels that require the Rip Fence to be positioned past the exposed side of the extension.
3-5/8
FACE & EDGE
MUST BE
PARALLEL
3/8 PLYWOOD
NOTE: All dimension in inches
AUXILIARY PANEL/WORK SUPPORT
CROSSCUTTING
CrosscutA cutting or shaping operation made across the width of the workpiece.
The graduations on the Miter Gauge provide accuracy lor average woodworking.
In some cases where ex-
treme accuracy is required, when making angle cuts, for
example, make a trial cut and then recheck it with an accurate square, or protractor.
If necessary, the Miter Gauge head can be swiveled
slightly to compensate for any inaccuracy.
NOTE: The space betweenthe Miter Gauge Bar andthe
groove in the table isheld to a minimum dudng manufac- turing.
For maximum accuracy when using the Miter Gauge, always '1avor"one side of the groove in the table.
In
other words, don't move the Miter Gauge from side to side while cutting, but keep one side of the bar riding against one side of the groove.
NOTE: Glue a piece of sandpaperto the face ofthe Miter
Gauge head. This will help prevent the workpiece from
"creeping" while it is being cut.
The Hold-Down Clamp (optional accessory) should be used on the Miter Gauge for greater accuracy.
The Miter Gauge may be used in either of the grooves in
._SANDPAPER
the table. Make sure it is locked.
WARNING: To avoid blade contact or kickback, hold the Miter Gauge properly.
When using the Miter Gauge in the LEFT hand groove, hold the workpiece firmly against the Miter Gauge head
with your left hand, and grip the lock handle with your right.
When using the RIGHT hand groove, hold the work-
piece with yourright hand and the Lock Handle with your left hand.
\
\
When cutting long workpieces, invert Auxiliary Panel/
Work Support and position it on top of the Guide Bars to
support the workpiece as near to the end as possible. If
this does not adequately supportthe workpiece, you can make a simple support by clamping a piece of plywood to a sawhorse. (See illustration above)
Use the Hold-Down Clamp (optional accessory) on the
Miter Gauge for greater accuracy.
AUXILIARY FENCE/
WORK SUPPORT
31
basic saw operation
REPETITIVE CUTTING
REPETITIVE CUTTING is known as cutting a quantity of
pieces the same length without having to mark each piece.
1. Use the Stop Rods (optional accessory) only for cutting duplicate pieces 6 inches long and longer.
2. Foitow all safety precautions and operational instructions for cross cutting.
When making repetitive cuts from a long workpiece, make sure it is adequately suppoded.
Use the Hold-Down Clamp (optional accessory) on the Miter Gauge for greater accuracy.
LEFT HAND REMOVED "\
FOR PICTURE CLARITY \
WORK SUPPORT i i
3. NEVER USE THE RIP FENCE AS A LENGTH STOP
BECAUSE THE CUT-OFF PIECE COULD BIND
BETWEEN THE FENC E AN D TH E BLADE CA USIN G
A KICKBACK.
4. When making repetitive cuts shorter than 6 inches,
clamp a block ofwood 2 inches long to the table to act
as a length stop. Do not clamp directly to the bottom
edge of the table because the "swivel" of the clamp
will not grip properly.
Place a small block of wood between the bottom edge of the table and the "C" clamp,
CAUTION: When clamping the block, make sure that the end of the block Is well In front of the sawblade.
Be sure it is clamped securely.
5. SrK:lethe workpiece along the Miter Gauge unt_ it touches the block, hold itsecurely or clamp itwith the
Hold-Down Clamp (optional accessory).
=
6. Make the cut, pull the workpiece back, turn the saw off, wait for Blade to stop and remove cut off piece before continuing.
MITER cu'ri'ING
MITER CUTTING is known as cutting wood at an angle
other than 90 ° with the edge of the wood. Follow the
same procedure as you would for crosscutting.
Adjust the Miter Gauge to the desired angle, and lock it.
The Miter Gauge may be used in either ofthe grooves in the table.
When using the Miter Gauge in the LEFT hand groove, hold the wo_ece firmly against the Miter Gauge head
with your left hand, and gdp the Lock Handle with your
right.
Whenusing the RIGHThandgroove, holdthe workplece
with your right hand and the Knob with your lefl hand.
Use the Hold-Down Clamp (optional accesson/) on the
Miter Gauge for greater accuracy.
32
BEVEL CROSSCUTTING
BEVEL CROSSCUTTING is the same as crosscutting
except that the wood is also cut at an angle, other than
90° with the flat side of the wood.
Adjust the blade to the desired angle.
Use the Miter Gauge in the groove to the RIGHT of the blade.
It cannot be used in the groove to the LEFT because the Blade Guard will interfere. Hold the workpiece with your right hand and the Lock Handle with your left hand.
Use the Auxiliary FenceNVork Support for additional support of the workpiece,
Lay itacross the Guide Bars to support the workpiece as near to the end as possible,
Use the Hold-Down Clamp (optional accessory) on the
Miter Gauge for greater accuracy.
COMPOUND MITER CUTTING
COMPOUND MITER CUTTING is a combination of miter cutting and bevel crosscutting. The cut is made at
an angle other than 90 ° to boththe edge and the flat side of the wood.
Adjust the Miter Gauge and the blade to the desired angle. Make sure Miter Gauge is locked.
5. A FEATHERBOARD can help guide the workpiece.
using the rip fence
RIPPING, BEVEL RIPPING, RESAWlNG AND RAB-
BETING are performed using the RIP FENCE together with the AUXILIARY FENCE/WORK SUPPORT, PUSH
STICK OR PUSH BLOCK.
WARNING: Foryourown safety, always observe the
following safety precautions in addition to the safety instructions on pages 2, 3, 4, 5, 28, 29 & 30.
ADDmONAL SAFETY INSTRUCTIONS FOR
RiP TYPE CUTS
1. NEVER use the Miter Gauge when ripping.
2. Use a Push Stick whenever the fence is 2 or more inches from the blade. When thru-sawing, use an
Auxiliary Fence and Push Biockwhenever the Fence must be between 1/2 inch and 2 inches of the blade.
Never thru-saw ripcuts less than 1/2 inchwide.
3. When using a Push Stick or Push Block, the trailing end of the board must be square.
A Push Stick or
Block againstan uneven end could slipoff or push the
work away from the fence.
4. Never rip anything shorter than 10 inches long.
KERFS ABOUT
5/16" APART
4-1/'
Before staring:
1. To avoid kickbacks and slips into the blade, make sure the Rip Fence is parallel to the sawblade,
2. Check the Anti-Kickback Pawls. The Pawls must stop a kickback once it has started.
Replace or sharpen Anti-Kickback Pawls when points become dull.
3. Plastic and composition (like hardboard) materials may be cut on your saw. However, since these are usually quite hard and slippery, the Anti-Kickback
Pawls may not stop a kickback. Therefore, be espe-
cially careful in your set-up and cutting procedures.
While cutting:
1. To avoid kickbacks and slips into the blade, a_ways push forward on the section of the wo rkpiece between
the saw blade and the Rip Fence. Never pushforward
on the piece being cut off.
33
basic saw operation
RIPPING
Ripping A cutting or shaping operation along the length of the workpiece.
Position the Fence to the desired WIDTH OF RiP and lock in place.
Before starting to alp,be sure:
1. Rip Fence is parallel to sawblade.
2. Spreader is properly aligned with sawblade.
3. Anti-Kickback Pawls are functioning properly.
When ripping LONG BOARDS or LARGE PANELS,
always use a work support.
A simple one can be made by clamping a piece of plywood to a sawhorse.
ALWAYS SUPPORT LONG WORKPIECES
USING FEATHERBOARDS
SAWING
FOR THRU
Featherboards are NOT employed for thru-sawing operations when using the Miter Gauge.
Featherbaords are used to keep the work in contact with
the Fence and table as shown, and to help stop kick- backs.
Add 7-1/2 inches high flat facing board to the Fence, the full length of the Fence.
Mount Featherboards to Fence and table as shown, so
that leading edges of Featherboards will supporl work- piece.
WARNING: Make surethe Featherboard against the edge presses only onthe uncut portion (forward o!
the blade), it might otherwise pinch the blade In the kerr and cause a kickback.
Before starting the operation (switch =OFF" and cutter below table sudace):
1, Install Featherboards so they exert pressure on the workpieoe; be positive they are secure, and
2. Make sure by trial that the Featherboards will stop a kickback if one should occur.
WORK
FEATHERBOARD
SUPPORT
"C" CLAMPS
FEATHERBOARD
CLAMPS
34
BEVEL RiPPiNG
When bevel ripping material 6 inches or narrower, use
Fence on the right side of the blade ONLY.
This will provide more space between the Fence andt he sawblade
for use of a Push Stick. If the Fence is mounted to the left, the Sawblade Guard may interfere with proper use of a Push Stick.
Keep your hands out of the blade path.
Feed the workpiece by pushing forward only on the part of the workpiece that will pass between the blade and fence.
Stop your thumbs at the front edge of the table.
Finishthe cut with the appropriate pusher.
Once the tralUng end is on the table:
When"WI DTH OF RiP" is 2 incheswide or more, use the
Push Stick to finish pushing the work all the way past the blade.
When thru-sawing a rip 1/2 inch to 2 inches wide, the
Push Stick CANNOT be used because the Guard will
interfere. USE the Auxiliary Fence/Work Support and
Push Block.
Attach Auxiliary Fence/Work Support to Rip Fence with
two "C" clamps.
35
basic saw operation
Feed the work,piece by hand along the Auxiliary Fence untilthe end is approximately I inch past thefront edge of the table. Continue to feed using the Push Block.
Hold the workpiece in position and installthe Push Block by sliding it on top of the Auxiliary Fence/Work Support
(this may raise Guard).
WARNING: Toavoid blade contact, never thru-saw
a rip less than 112Inch wide.
Narrow strips thicker than the Auxiliary Fence/Work
Support may enter the Guard and strike the Baffle.
CAREFULLY raise Guard only enough to clear the workpiece. Use Push Block to complete cut.
BAFFLE
RESAWlNG
RESAWlNG isknow n as ripping a piece of wood through its thickness.
Do not attempt to resaw BOWED or
WARPED material.
NOTE: To RESAW a piece of wood wider than 3_/8 inches, it will be necessawto remove the blade guard
andusethe Auxiliary Fence/Work Support. (See _WORK
HELPERS').
Clamp it to the table so that the workpiece will SLIDE
EASILY but not TILT or MOVE SIDEWAYS without
BINDING between the two Fences.
Do not clamp directly to the bottom edge of the table because the "swivel"of the clampw!ll notgrip properly.
Place a small block ofwoodbetweenthe bottom edge of
the table and the "(;"clamp.
WARNING: For your own safety
1. Do not "Back up" (reverse feeding) while resaw-
SMALL BLOCK
OF WOOD
!
36 ing because this could cause a kickback.
2. Make the first pass to a depth slightly more than
1/2the width ofthe board. Keep the same face of the board against the fence for the second pass,
3. Install Blade Guard immediately upon comple-
tion of the resawlng operation.
AUXILIARY PANEL/
CUTTING PANELS
When cutting panels (whenever fence is positioned outside of table surface), ALWAYS use the Auxiliary
Fence/Work Support.
1. Unlock Fence and raise rear end.
2. PositionAuxiliary Fence/Work Support as shown and attach it with two "C" clamps.
RABBETING
RABBETING is known as cutting out a section of the comer of a piece of material, across an end or along an edge.
To make a RABBET requires cuts which do not go all t he way through the material.
Therefore, the Blade Guard must be removed.
1. Remove Blade Guard.
2. For rabbeting along an edge (long way of work-
piece) as shown, add facing to Rip Fence approxi-
mately as high as the workpiece is wide. Adjust Rip
Fence and blade to required dimensions; then make first cut with board flat on table as any rip(type) cut;
make second cut with workpiece on edge. Follow all precautions, safety instructions, and operational in-
structions as for dpping, or riptype operations, includ- ing Featherboards and Push Stick, etc.
3. For rabbeting across an end, for workpiece 10-1/2
inches and narrower, make the rabbet cut with the board flat on the table. Using the Miter Gauge fitted with a Facing, follow the same procedures and instructions for cross cutting making successive cuts across the width of the workpiece to obtain the desired width of cut.
DO NOT use the Rip Fence for rabbeting across the end.
4. INSTALL BLADE GUARD IMMEDIATELY UPON
COMPLETION OF RABBETING OPERATION.
Rabbet cuts can also be made in one pass of the workpiece over the cutter using the Dado Head or
Molding Head.
RABBET
PLOUGHING AND MOLDING
PLOUGHING is grooving with the grain the long way of the workpiece, using the Fence, USE featherboards and push sticks as required.
FIRST CUT 1 t
I SECOND CUT
RABBETING ALONG
THE EDGE
./
/
/
/
RABBETING
ACROSS THE END
/
/
J /
J
MOLDING is shaping the workpiece with the grain the
long way of the workpiece, using the Fence.
Use
featherboards and push sticks as required.
MOLDING PLOUGHING
37
basic saw operation
DADOING
Instructionsfor operating the Dado Head are contained in booklet furnished with the Dado Head.
The arbor on the saw, is only long enough so that the widest cut that can be made is 13/16 inch wide.
It is not necessary to install the outside loose collar
before screwing on the arbor nut. Make sure the arbor nut is tight.
ALWAYS USE DADO INSERT LISTED UNDER "REC-
OMMENDED ACCESSORIES."
When using the Dado Head it will be necessary to remove the Blade Guard and Spreader.
USE CAU-
TION.
USE MITER GAUGE,FENCE, FEATHER-
BOARDS OR PUSH STICKS, etc. AS REQUIRED.
ALWAYS REPLACE THE BLADE, GUARD AND
SPREADER WHEN YOU ARE FINISHED DADOING.
LOOSE CC )LL
ARBOR NU
PT_f t "_ SAW ARBO
REMOVE SAWBLADE ANC
INSTALL DADO HEAD
BACK OF SAW
MOLDING CUTTING
Instructions for operating the Molding Head are contained in a booklet furnished with the Molding Head.
Always use Molding Insert listed under "RECOM-
MENDED ACCESSORIES".
When using the Molding Head, it will be necessary to i
USING FEATHERBOARDS
THRU SAWING
FOR NON-
Featherboards are not employed dudng nonthru-sawing operations when using the Miter Gauge.
Use Featherbaords for all other non thru-sawing operations (when sawblade guard must be removed).
Featherboards are used to keep the work in contact with the fence and table as shown andto stop kickbacks.
Add 7-1/2 inch high flat facing board to the fence, the full length of the fence. Mount Featherboard tofence and table as shown, so that leading edges of Featherbaords will support work,piece until cut is complete, and the
workplace has been pushed completely past the cutter
(sav/olade, dado head, molding head, etc.) with a Push
Stick, as in dpping;
Before starting the operation (switch "OFF" and cutter below table surface):
workplace; be pesitive they are secure, and
2. Make sum by trial that the Featherboards will stop a kickback itone should occur.
Replace the sawb|ade guard as soon as the non thru- sawing operation is complete.
removethe Blade Guard and Spreader. USE CAUTION.
USE MITER GAUGE, FENCE, FEATHERBOARDS OR
PUSH STICKS, ETC. AS REQUIRED.
ALWAYS REPLACE THE BLADE GUARD AND
SPREADER WHEN YOU ARE FINISHED MOLDING.
"'C" CLAMPS
FEATHI:RBOARD
CLAMPS
38
adjustments
WARNING: For your own salety, turn switch "OFF" and remove plug from power source outlet before making any adjustments.
MITER GAUGE
NOTE: The Slotsfor the Stop Pin and the graduations are manufactured to very close tolerances which pro- vide accuracy for average woodworking. In some cases where extreme accuracy is required, when making
angle cuts, for example, make a trial cut and then recheck it.
If necessary, the Miter Gauge head can be swiveled slightlyto compensate for any inaccuracy.
1. Loosen the "knob" and pull "Stop Pin" OUT.
2. Swivel the head, position it at "0%push the Stop Pin
IN, lock the Handle.
3. The HEAD should be square with the Bar and the
Pointer should point to "0". Readjust the Pointer if necessary.
4. Ifthe headis not squarewith the Bar, adjustments are required.
A. Loosen the "knob" (t) and the "two screws" (2)
B. Position the HEAD square with the Bar using a combination square.
C. PUSH the Stop Pin into the slot in the head at "0", push the Pin into the slot and twist it. Lock the
Knob.
D. Recheck with the square.
If the head is still not square, loosen the screws (2) and readjust the
Indicator Blcok.
E. With the head square with the Bar and the Pin
pushed intothe slot, adjust the Pointer (3) to point
to "0".
F. The Miter Gauge head must rest on top of the Bar
without being able to move up and down, yet it
HEELING ADJUSTMENT OR
PARALLELISM OF SAWBLADE TO MITER
GAUGE GROOVE
While cuffing, the material must move in a straight line
PARALLEL to the SAWBLADE.
Therefore, both the
Miter Gauge Groove andthe Rip Fence must be PAR-
ALLEL to the Sawblade_
If the sawblade IS NOT parallel to the Miter Gauge
Groove, the blade will bind at one end of the cut. (This
is known as "HEELING").
To check for parallelism:
WARNING: For your own safety, turn switch "OFP" and remove plug from power source outlet.
1. Raise blade all the way up, raise Blade Guard.
2. Markan"X" on one of the teeth which isSET (bent) to the LEFT.
39
WRENCH
BAR
SQUARE
LOCK KNOB
\
!
2"_
STOP
PIN
INDICATOR
BLOCK must swivel freely.
G.The swiveling movement of the head can be adjusted by tightening or loosening the setscrew (4)
using the 1/8 inch setscrew wrench,
NOTE: The setscrew is located inside of the head.
To reach it, swivel the head to 60 ° andturn the Miter
Gauge upside down,
!
adjustments
3. Place the head of a combination square in the
GROOVE.
Adjust blade of square so that it just touches the tip of the MARKED tooth.
4. Move squareto REAR, rotate blade to see if MARKED
tooth again touches blade of square.
5. If tooth touches square at FRONT and REAR.
sawblade is PARALLEL to Miter Gauge Groove.
6. If tooth does not touch the same amount, the mecha-
nism underneath must be adjusted to make the blade
PARALLEL to GROOVE.
A. Rear Trunnion must be moved TOWARD to com-
bination square Ifthere is a space between marked tOOthand end of square in step 4.
B. Rear Trunnion must be moved AWAY from the square if marked tooth pushes square out of posi- tion in the groove.
FRONT TRUNNION REAR TRUNNION
....
REAR-TRUNNION
SCREWS
7. Loosen all three screws that hold the Rear Trunnion
and all three screws that hold the Front Trunnion.
NOTE: All six screws can be reached through back
of saw. Use a 9/16 inch wrench. To reachleft-hancl
Front Trunnion screw, tilt blade to 45 ° . After loosening screws, reposition blade at 90 a.
RI|GHT-/HAND
•
/ l CENTER
(BEHIND HERE)
!
FRONT-TRUNNION SCREWS
LEFT-HAND
(BEHIND HERE)
\,
8.
Using awoodblock and mallet, as shown, move Rear
Trunnion to right or left as required to realign the blade, if necessary, shift Front Trunnion in similar manner; but do NOT move Front Trunnion unless
EDGE OF TRUNNION
CLAW HAMMER
WOOD BLOCK
PLACE BLOCK HERE
-- OR HERE
REAR OFSAW
I
EDGE OF
CRADLE
40
BLADE TILT, OR SQUARENESS OF
BLADE TO TABLE
When the Bevel Pointer is pointing directly to the "0" mark on the Bevel Scale, the sawblade should make a
SQUARE cut 90° to the table.
90° Position
To check for SQUARENESS:
WARNING: For your own safety, turn switch "OFF" and remove plug from power source outlet.
1. Raise blade all the way UP, raise Blade Guard.
2. TILTblade afewdegreestothe LEFT. Now, tilt blade
back to the RIGHT as far as it will go.
3. Place the square against blade. Make sure square is not touching the TIP of one of the saw TEETH.
4. Operate the 131t-Lock Handle (COUNTERCLOCK-
WISE) to loosen the Tilt Clamp screw.
5. NOTE: Handle is spring loaded for engagement with screw head - must be pushed inward for disengagement whenever necessary to obtain a new grip on screw head.
__---'_
.'_
TILT CLAMP SCREW
-'_ TIL_T LOCK HANDLE
6. Rotate "131t a few tumsto tilt blade. Now, rotate Handwheel COUNTERCLOCK-
WISE until it stops. Blade should now be square with
table and Pointer should point to "0".
A. If blade is SQUARE to table;
1. Check Pointer.
B. IF POINTER DOES NOT point to the "(3"mark on the Bevel Scale;
1. Remove Elevation Handwheel.
2. Loosen screwand adjust Pointer using medium screwdriver
3. Install Elevation Handwheel.
POINTER AT
"0" POSITION
BEVEL SCALE
TILT HANDWHEEL
I TIL,T
1"/
°,NisR
POINTER
,ADJUSTING SCREW
\
SCALE ADJUSTING
SCREW
41
ad ustments
C. If blade is NOT SQUARE to table.., the 90 • Stop
Screw must be ADJUSTED.
1. Unscrew 90 ° Stop Screw three to four turns
using 3/16 inch Hex "L" wrench.
2. Turn Tilt Handwheel clockwise one turn, then turn Handwheel counterclockwise until blade is square with table.
3. Screw 90 ° Stop Screw IN until it stops. Check
once again for squareness and readjust screw, if necessary.
i=
45" Position
TILT blade to LEFT as far as it will go.
1. Place an ACCURATE square against blade. Make sure square is not touching the TIP of one of the saw
TEETH.
If blade is 45 ° to table;
1. Check Pointer.
........
i
If blade is NOT 45' TO TABLE... STOP SCREW and
SCALE must be ADJUSTED.
1. Unscrew 45 ° Stop Screw three to four turns using
3/16 inch setscrew wrench.
2. Tum Tilt Handwheel until blade is 45 _to the table.
3. Screw 45 ° Stop Screw IN until it stops. Check once
again and readjust screw, if necessary.
/
!
/
/
If POINTER DOES NOT point to the 45 ° mark on the scale;
1. Remove Elevation Handwheel.
2. Loosen two screws on Scale and adjust Scale until
Pointer points to 45° mark.
3. Install Elevation Handwheel.
TILT MECHANISM
the nut inside using a 3/8 inch wrench.
42
\
\
\
\
\
\
© /
45 °
STOPSCREW
\
\
\
\
\
\
maintenance
WARNING: For your own safety, turn switch "OFF" and remove plug from power source outlet before maintaining or lubricating your saw.
Do not allow sawdust to accumulate inside the saw.
Frequently blow out any dust that may accumulate inside the saw cabinet and the motor,
Frequently clean your cutting toolswith Craftsman Gum and Pitch Remover.
A coat of automobile-type wax applied to the table will
help to keep the surface clean and allow workpieces to slide more freely.
If the power cord is worn or cut, or damaged in any way, have it replaced immediately.
Make sure the teeth of the Anti-Kickback Pawls are always sharp. To sharpen:
1. Remove Blade Guard.
mubrication
The following parts should be oiled occasionally with
SAE No. 20 or No. 30 engine oil.
1. Tilt screw threads and pivot nut. (First clean with
Craftsman Gum and Pitch Remover.)
2. Elevation screw threads and pivot nut. (First clean with Craftsman Gum and Pitch Remover.)
3. Cradle bearing points.
4. Bearing points in Guard Assembly, Miter Gauge and
Rip Fence.
\
\
2. Rotate Pawl toward rear of Spreader so that teeth are above top of Spreader.
3. Hold Spreader with left hand and place Pawl over corner of workbench.
4. Using a small round file (smooth cut) sharpen the teeth.
GUARD t BEARING POINTS
sears recommends the following accessories
ITEM CAT. NO. ITEM
Caster Sets ...............................
9-22222 or 9-22221
7 In. Molding Head Set ...........................
See Catalog
7 In. Molding Head .................................
8 In. Molding Head .................................
Molding/Dado Insert for 7 In. Dia. Molding or Dado Head ..........................................
See Catalog
See Catalog
9-29997
Molding/Dado Insert for 8 In. Dia. Molding or Dado Head ..........................................
9-22287
Work Light .............................................
See Catalog
7 In. Dia. Adjustable Dad0 Head ..............
See Catalog
7 In. Dia. Dado Head ...............................
See Catalog
Sanding Wheel ......................................
See Catalog
CAT. NO,
Miter Gauge Stop Rods ................................
9-29924
Miter Gauge Hold-Down Clamp .....................
9-29928
Taper Jig ...............................................
See Catalog
Universal Jig ..........................................
See Catalog
Power Tool Know How Handbook ................. 9-29117
Sears may recommend other accessories not listed in manual.
See your nearest Sears Store or Catalog Department for other accessories.
Do not use any accessory unless you have received and read complete instructions for its use.
43
trouble shooting
WARNING: For your own safety, turn switch "OFF" and always remove plug from power source outlet before trouble shooting.
TROUBLE SHOOTING - GENERAL
TROUBLE i
Excessive vibration
Cannot make squ are cut when crosscutting.
Cut binds, burns or stalls motor when ripping.
Cut not true at 90 ° or
45° positions.
Tilt and elevating handwheel turn hard.
PROBABLE CAUSE i
1. Blade out of balance.
1. Miter gauge not adjusted properly,
1. Dull blade or improper tooth set.
2.
3.
Blade is Heeling.
Warped board.
4.
Rip Fence not parallel to blade.
5.
Spreader out of alignment.
1.
Stop collars not properly adjusted.
I.
Sawdust on threads of tilt
screw or elevating screw.
2. Bearing retainers too tight.
REMEDY
1. Discard Blade and use a different blade.
1. See "Adjustments" section "Miter Gauge."
1. Sharpen or replace blade.
2. See "Adjustments" section, "Heeling Adjustment.."
3. Make sure concave or hollow side is facing
"down," feed slowly.
4. See "Assembly" section, "Aligning Rip Fence."
5. See "Assembly"
.
section, "installing Blade Guard."
1. See "Adjustments" section, "Blade Tilt, or
Squareness of Blade to Table."
.
See "Maintenance" and "Lubrication" sections.
See "Maintenance" section, "Tilt and Elevation
Mechanism"
TROUBLESHOOTING - MOTOR
NOTE: Motors used on wood working tools ar particularly susceptible to the
accumulation of sawdust and wood chips and should be blown out or "vacuumed" frequently to prevent interference with normal motor ventilation.
TROUBLE
Excessive noise.
I
I
_ PROBABLE CAUSE
1. Motor
Motor fails to develop full power. NOTE:
LOW Voltage:
(Power output of motor decreases rapidly with decrease .
1. Circuit overloaded with lights, appliances and other motors.
too long.
REMEDY
1. Have motor checked by qualified service technician.
Repair service is available at your nearest
Sears store,
1. Do not use other appliances or motors on same circuit when using the saw.
2. Increase wire sizes, or reduce length of wiring.
See "Motor Specifications and Electrical Requirements" section.
44
TROUBLESHOOTING - MOTOR (Cont'd)
TROUBLE
Motor starts slowly or fails to come up to full speed
Motor overheats
Starting switch in motor will not operate
Motor stalls.
(resulting in blown fuses or tripped circuit breakers)
Frequent opening o! fuses or circuit breakers
PROBABLE CAUSE
1. Low voltage.
2. Windings burned out or open.
3. Starting switch not operating.
1. Motor overloaded
2. improper cooling.
(Air circulation restricted through motor due to sawdust, accumulating inside of saw.)
1. Burned switch contacts
(due to extended hold-in periods caused by low line voltage, etc.)
2. Shorted capacitor
(when equipped)
3. Loose or broken connections.
1.
Starting switch not operating.
2.
Voltage too low to permit motor to reach operating speed.
3. Fuses or circuit breakers do not have sufficient capacity.
1. Motor overloaded
2. Fuses or circuit breakers do not have sufficient capacity.
3. Starting switch not operating (motor does not reach speed.)
REMEDY
1. Request voltage check from the power company.
2. Have motor repaired or replaced.
3. Have switch replaced.
2.
.
Feed work slower into blade,
Clean out sawdust to provide normal air circulation
through motor.
See "Maintenance" and
"Lubrication" section.
1. Have switch replaced and request a voltage check from the power company.
2. Have capacitor tested and replace if defective.
3. Have wiring checked and repaired.
1. Have switch replaced.
2. Request voltage check from the power company.
3. Install proper size fuses or circuit breakers.
1. Feed work slower into blade.
2. Install proper size fuses or circuit breakers.
3. Have switch replaced.
45
repair parts
\
I
!
I
/
!
/
/ r
N
46
r,-
O_ 0 0
5
18 t,O
I'-.
,T-
O
Z m
0
O)
Z
Z
.,.
Z
O') u
R n," n-
O r,..
0
_L
,,,,,,I
.,J uJ a
0
F-,
1£
_L
__o_o___oo
[
8
____
0 _
_ O0
._(2
Eo oE t-
O.
__
-.a o
..(3 0 m t""
_r_. __
.___
.._
r-
13 tt_
O_ a::_>,
"0
'_ o
0
>
_d
.._.
"0 0
._: -_
=g$
47
repair parts
48
IN
W
It,"
49
E
Q
_o
_ 0
0
-r
N o m i
E
€-
3
0.
repair parts
PARTS LiST FOR CRAFTSMAN 10 INCH TABLE SAW
MODEL 113.298721
AND 113.298761
!
L
FIGURE 3- ON-OFF POWER OUTLET
KEY
NO.
PART
NO.
60375
60380
9-22255
60374
60377
448007
DESCRIPTION fi= .
Cord, Molded
Housing, Switch
Key, Switch
Switch, Locking
Cover, Switch
Screw, Pan Hd. No. 6 x 3/4
5O
PARTs LiST FOR CRAFTSMA_ 10 iNCH TABLE SAW
MODEL 113.298721
A_E) 113.298761
FIGURE 4 - TABLE EXTENSIONS
[" KIEY
I NO. i 1
2
3
4
5
6
7
8
PART --
NO.
9-22261
STD541231
STD551231
STD523t07
STD551031
818308
62539
STD523112
DESCRIPTION
1 Extension, Table 12 x27
" Nut, Hex 5/16-18
* Lockwasher, External 5/16
" Screw, Hex Head
5/16-18 x3/4
* Washer, 21t64 x 5/8 x 1/16
Bracket
Spacer, Fence Guide Bar
" Screw, Hex Hd.
5/16-18 x 1-1t4
* Standard Hardware Item - May be purchased locally t Stock Item - May be secured through the Hardware
Department of most Sears Retail Stores or Catalog
51
repair Parts
PARTs L'IST FOR CRAFTSMAN 10 iNCH TABLE. SAW
MODEL 173.2S872_AND _l,_.2987S_
2
\
12
/
N°- 4-40 x1/4 /
x 1/2 I
52
PARTS LIST FOR CRAFTSMAN 10 INCH TABLE SAW
MODEL "!13.298721
AND 113.298761
FIGURE 6 - MITER GAUGE ASSEMBLY
KEY
NO.
PART
NO.
1 62693
2 62692
3 STD551031
4 37893
5 STD510803
6 135
7 37895
8 37896
9 9417295
10 62230
11 STD541231
12 62225
13 62383
14 60288
DESCRIPTION
Plug, Button
Knob, Miter Gauge (Includes Key No. 1)
* Washer, Plain, 21/64 x 1 x 1/16
Gauge, Miter
* Screw, Pan Hd. 8-32 x 5/16
Indicator
Block, Miter Gauge Indicator
Pin, Miter Gauge Stop
* Screw, Pan Hd., w/Lockwasher, 8-32 x 5/8
Rod Assembly, Miter Gauge,
Consisting of Items 11,12, 12
* Nut, Hex., 5/16-18
Stud, Clamp
Stud, Pivot
Screw, Locking Set 114-20 x 3/8
° Standard Hardware Item - May be purchased locally.
53
repair parts
I
PARTS LiST FOR CRAFTSMAN 10 INCH TABLE SAW
MODEL 113.298721
AND 113.298761
2
3
4
5 !
_) _::::::_ /
/
/
/
/
/
6
/
12
10
9
/
FIGURE 7 - GUARD ASSEMBLY
KEY,
NO,,
9
10
11
12
3
4
1
2
5
6
7
8
PART
NO.
60208
62391
62395
62389
62390
STD551025
,
62520
62396
62410
STD571810
62519
DESCRIPTION
Nut, Push
Pin 1/4 x 1-1/2
Support, Guard
Guard, Saw
Pin, 1/4x 1-3/4
* Washer, 17/64 x 5/8 x 1/16
• Spacer, Pawl
Pawl
Spreader Assembly, Blade
Pin, 1/4x 1
• Pin, Roll 3/16 x 15/16
Spring, Pawl
" Standard Hardware Item - May be purchased locally
54
PARTS LiST FOR CRAFTSMAN 10 iNCH TABLE SAW
MODEL 113.298721
AND 11:3.298761
3 4 5
5 4 1
1 f
12 11
2_
2
/
,/
FIGURE 8 - LEG SET
KEY
NO.
7
8
3
4
5
6
1
2
PART
NO.
60314
819441
62554
STD551225i
STD541025
62553
STD541237,
803835-t
DESCRIPTION
Screw, Serrated Truss HcI.
1/4-20 x 1/2
Leg
Stiffener, Side
* Lockwasher, Ext. 1/4
* Nut, Hex 1/4-20
Stiffener, End
* Nut, Hex 3/8-16
Foot, Leveling
HARDWARE FOR ATTACHING LEGS TO SAW
9
10
11
12
STD5231121 * Screw, Hex Hd. 5/16-18 x 1-1/4
STD551031 Washer, 11/32 x 11/16 × 1/16
STD551231 * Lockwasher, Ext. 5/16
STD541231 * Nut, Hex 5/16-18
* Standard Hardware Item - May' be purchased locally
55
10-iNCH TABLE SAW
SERVICE
Now that you have purchased your 10 inch Table
Saw, should a need ever exist for repair parts or service, simply contact any Sears Service Center and most Sears, Roebuck and Co. stores.
Be sure to provide all pertinent facts when you call or visit.
The model number of your Table Saw will be found at the left-hand side of the base.
MODEL
NO'S,
113.298721
113.298761
HOW TO ORDER
REPAIR PARTS
WHEN ORDERING
THE FOLLOWING
REPAIR PARTS, ALWAYS GIVE
INFORMATION:
PART NUMBER PART DESCRIPTION
MODEL NUMBER
113.298721
113:298761
NAME OF ITEM
10 Inch Table Saw
All parts listed may be ordered from any Sears Service
Center and most Sears stores.
If the parts you need are not stocked locally, your orderwilt be electronically transmittedto a Sears Repair Parts Distribution Center for handling.
Sold by SEARS, ROEBUCK AND CO., Chicago, IL 60684 U.S.A.
Part No. SP5396 Form No. SP5396-2 Printed in U.S.A. 8/92
advertisement
Key Features
- 10-inch blade for larger cuts
- Powerful motor for demanding tasks
- Quick-release rip fence for fast and accurate adjustments
- Cast iron table extensions for stability and durability
- Blade guard, spreader, and anti-kickback pawls for enhanced safety
- Easy assembly and alignment
- Convenient storage space for accessories
Related manuals
Frequently Answers and Questions
What materials can I cut with this saw?
What is the maximum cutting depth?
Can I use dado blades with this saw?
How do I adjust the blade height and angle?
What safety precautions should I take when using this saw?
advertisement