DVB-T Set-Top-Box

DTR 705

DTR 705

USER MANUAL

English

FCC and Safety Information

NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

FCC and Safety Information

Important Safety Instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with a damp cloth.Please unplug power.

7. Do not block any of the ventilation openings. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized-type plug. A polarized plug has two blades with one wider than the other. The wide blade is provided for your safety. When the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plug, convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lighting storms or when unused for long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way; such as when the power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

A Class II APPARATUS shall be permanently marked with the words DOUBLE INSULATION or Double insulated and hen servicing use only identical replacement parts.

WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.

Precautions

Please read these precautions before operating this unit.

Power cord protection

To avoid any malfunctions of the unit, and to protect against electric shock, fire or personal injury, please observethe following.

Hold the plug firmly when connecting or disconnecting the AC power cord.

Keep the AC power cord away from heating appliances.

Never put any heavy object on the AC power cord.

Do not attempt to repair or reconstruct the AC power cord in any way.

Never make or change connections with the power switched on.

Placement

Avoid placing the unit in areas of:

direct sunlight or heating radiators, or closed automobiles

high temperature (over 350C) or high humidity (over 90%)

much dust as the internal parts may be seriously damaged.

Non-use periods

When the unit is not being used, turn it off. When left unused for a long period of time, the unit should be unplugged from the household AC outlet.

No fingers or other objects inside

Touching internal parts of this unit is dangerous, and may cause serious damage to the unit. Do not atte

important to disassemble the unit.

Do not put any foreign object in this unit.

Keep away from water/magnet

Keep the unit away from flower vases, tubs, sinks, etc. If liquids are spilled into the unit, serious damage

could occur.

Never bring a magnet or magnetized object near the unit.

Stacking

Place the unit in a horizontal position, and do not place anything heavy on it.

Condensation

Moisture may form on the lens in the following conditions:

immediately after a heater has been turned on

in a steamy or very humid room

when the unit is suddenly moved from a cold environment to a warm one

If moisture forms inside this unit, it may not operate properly. In this case, turn on the power and wait about

one hour for the moisture to evaporate.

If there is noise interference on the TV while a broadcast is being received

Depending on the reception condition of the TV, interference may appear on the TV monitor while you watch a TV broadcast and the unit is left on. This is not a malfunction of the unit or the TV. To watch a TV broadcast, turn off the unit.

English

This symbol on the product or in the instructions means that your electrical and electronic equipment should be disposed at the end of its life separately from your household waste.

There are separate collection systems for recycling in the EU. For more information, please contact the local authority or your retailer where you purchased the product.

CONTENTS

FCC and Safety Information

INTRODUCTION

Rear panel 1

Remote control 2

SYSTEM CONNECTION

General about connections

Connection to the TV and video recorder with SCART

Connecting a HiFi System

3

3

3

GETTING STARTED

WELCOME PAGE

System setup

INSTALLATION

Automatic channel scan

Manual channel scan

Aerial Adjustment

OPERATION

Accessing the favorite channels

Access the Electronic Programme Guide(EPG)

CHANNEL

Channel list

Channel list menu

TV Channel list

Radio Channel list

Delete All Favorites

Delete All Channels

SYSTEM SET UP

System setup main menu

OSD Language

TV System

Start up Service

Region and Time

Timer Setting

OSD Setting

Parental Lock

TOOLS

Tools main menu

Information

Load Factory Default

Remote Control Help

7

7

18

18

19

19

13

13

14

15

15

16

17

17

5

5

6

4

4

8

8

9-11

11

12

12

INTRODUCTION

Front panel

Standby button

Power indicator

DTR 705

Channel up

Channel down

Remote sensor

Rear panel

TV aerial

Coaxial Digital Audio for an external TV aerial

AUX Scart for connection to a VCR or a satellite receiver

AC Mains

RS232

AC220-240V

~50/60Hz

DVB-T SET TOP BOX

POWER SUPPLY: AC 220-240V~50/60Hz

POWER CONSUMPTION: 10WATTS

Art-Nr.:_________

Veseg GmbH, Ostring 60,

D-66740 Saarlouis-Fraulautern

DTR 705

Serial port for connection to PC

TV Scart for connection to the TV

1

INTRODUCTION

1

2

3

4

5

6

7

8

9

10

VOL

+

12

13

14

15

16

17

18

19

20

21

11

2

1

2

3

4

Power On/Standby

(Switch the STB ON/STANDBY mode)

Numeric entry

(Enter numeric values and to select the channel directly by entering it's number)

Menu

(Open up menu)

Red Button (For teletext function)

Page up

7

8

5

6

9

Cursor/ Enter

( to select sub-menu from the main menu and channel +/-,

to select menu and sub-menu from the menu and volume +/-,

Press to enter.)

Yellow Button

(For teletext function)

Mute

RECALL

(switch to previous channel)

EPG

(Open up Electronic Program Guide menu)

10 TTX

(Open Teletext function)

11

12

13

DTV/VCR

(Switch between TV and external input through AUX scart)

EXIT

(Exit from menu)

Green Button (For teletext function)

Page down

14 Blue Button

(For teletext function)

15 FAVORITE

(Open up Favourite list)

16

17

18

PAUSE

INFO

(Press for current channel information)

LANG

(Select language for the two or more language simultaneous programmes)

19

20

21

AUDIO

(Select audio: Left / Right /Stereo / Mono)

TV/RADIO

(Switch between TV and Radio)

SUBTITLE

(On/Off Subtitle)

SYSTEM CONNECTION

General

There are many different types of TV/VCR and other equipment that you can connect to the STB.In this manual you will see some of the most common ways to connect your equipment.

Connection to the TV and video recorder

with SCART

Scart cable

Antenna

RS232

AC220-240V

~50/60Hz

DVB-T SET TOP BOX

POWER SUPPLY: AC 220-240V~50/60Hz

POWER CONSUMPTION: 10 WATTS

Art-Nr.:_________

Veseg GmbH, Ostring 60,

D-66740 Saarlouis-Fraulautern

DTR 705

TV

VCR

Video Cassette Recorder

Scart cable

Connecting a HiFi system

Hi-Fi

Coaxial cable

3

4

RS232

AC220-240V

~50/60Hz

DVB-T SET TOP BOX

POWER SUPPLY: AC 22 0-240V~50/60Hz

POWER CONSUMPTION: 10 WATTS

Art-Nr.:_________

Veseg GmbH, Ostring 60,

D-66740 Saarlouis-Fraulautern

DTR 705

GETTING STARTED

WELCOME PAGE

If you use the STB the first time or after you delete all channel information in the STB,the

"WELCOMOE PAGE" picture for quick shortcut menu will display .

Press "1~5" numeric button to enter Region, OSD Language Tuner

Power, Auto Scan and Main Menu quickly.

MENU

Press to return.

1

2

3

4

5

WELCOME PAGE

OSD Language

Region

Tuner Power

Auto Scan

Main Menu

System setup

1

MENU

Press the to enter the setup menu of the STB.

2 Press the to select "Setup" .

3 Press the to enter the sub-menu.

4

5

Press to select the desired item and press to confirm.

MENU

Press to exit.

Main Menu

Channel

Installation

Setup

Tools

Select OK Enter MENU Exit

System Setup

OSD Language

TV System

Start up Service

Region and Time

Timer Setting

OSD Setting

Parental Lock

Select OK Enter MENU Exit

4

Installation

1

2

3

4

MENU

Press the to enter the setup menu of the STB.

Press to select "Installation".

Press to enter the sub-menu.

Select the "Auto Scan" and press , Auto Scan menu appears

5 Press to select Scan mode and highlight "Search",then press the to confirm .

Installation

Auto Scan

Channel Scan

Aerial Adjustment

Auto Scan

Scan Mode

Search

All

Automatic channel scan

Auto Scan

UHF 470.0~862.0 MHz Ch No.

Frequency 858.00 MHz FFT

Modulation GI

TV Service Radio Service

40%

MENU Exit

Select OK Enter MENU Exit Select Change OK Enter MENU Exit

The automatic search will start and the picture shown right is displayed.

1

2

3

4

MENU

Press to enter the setup menu of the STB.

Press to select "Installation".

Press to enter the sub-menu.

Select the "Channel Scan" and press , Channel

Scan menu appears

5 Press to select Scan mode,

Scan Band and Channel No. and highlight "Search",then press

to confirm .

Manual channel scan

Main Menu

Channel

Installation

Setup

Tools

Select OK Enter MENU Exit

Installation

Auto Scan

Channel Scan

Aerial Adjustment

Channel Scan

Mode

Scan Band

Ch No.

Frequency

BandWidth

Search

Signal Intensity

Signal Quality

Select

By Channel

UHF

21

000.000MHz

8 MHz

Change

65%

90%

0-9 Input MENU Exit

Channel Scan

UHF 470.0~478.0 MHz

Frequency FFT

Modulation GI

TV Service Radio Service

40%

MENU Exit

Select OK Enter MENU Exit

Your STB will start to scan the desired service or Frequency and the picture shown right is displayed.

Channel Scan mode: By channel

By frequency

5

Installation

Aerial Adjustment

When you adjust the location of aerial,use this menu to check signal intensity and quality of the selected channel.

MENU

1

2

3

4

Press to enter the main menu of the STB.

Press to select "Installation".

Press the to enter the sub-menu.

Select the "Aerial Adjustment" and press , Aerial

Adjustment appears.

5 Press to select the desired channel No.

Main Menu

Channel

Installation

Setup

Select OK Enter

Tools

MENU Exit

Installation

Auto Scan

Channel Scan

Aerial Adjustment

Select OK Enter MENU Exit

Aerial Adjustment

Ch No.

Tuner Power

21

On

Signal Intensity

Signal Quality

Change MENU Exit

65%

90%

The signal intensity and quality for the desired channel will display as above.

6

OPERATION

1

FAVORITE

Press to open up the "FAVOURITE LIST".

2 Press to select the desired favourite group.

3 Select the favourite channels and press to view the selected channel.

Accessing the favorite channels

Favorite Group 1

0001 HN Radio2

0002 BBC NEWS 24

0003 BBC Text

0004 BBC Two

Installation

System Setup

Tools

Accessing the Electronic Program Guide (EPG)

Accessing the EPG of all channels:

1

EPG

Press to enter EPG menu .

2

Press to view the current selected in full screen.

3 Press the numeric button"1" to display all programs schedule information of the selected channel as right.

4 Press the numeric button"2" to display the detail informations of current channel.

Schedule 15/02/2006 14:29

0002 BBC NEWS 24

15/02/2006

Detail 15/02/2006 14:29

BBC NEWS 24

13:00-15:00 BBC News

Bill Turnbull and Valerie Sanderson present the news,with live reports from around the world. Widescreen.

EPG 15/02/2006 14:29

0001 HN Radio2

0002 BBC NEWS 2

0003 BBC Text

0004 BBC Two

0005 BBC CHOICE

14:05-14:55

BBC News

Theme: News

Rate:00

15:00-16:00

BBC News

Theme: News

Rate:00

1

Select

Schedule 2

Page

Detail

OK Enter MENU Exit

OK

Select

Enter 1

Date

Detail 2

Page

Timer

MENU Exit

Page MENU Exit 1 Extend 2 Timer

5 In schedule and detail menu,press numeric button "2" can open the timer menu directly. This operation can add the highlighted program to a timer quickly.

7

CHANNEL

Channel list

There are four ways of channel selection - stepping through the channel list, selection by number, from the on-screen channel list, and using the electronic programme guide(EPG).

1

2

3

Stepping through the channel list:

To move through the channel list, press the upward arrow or downward arrow

key on the remote control.

Selection by number:

Enter the channel list number directly by remote control to select desired channel.

Selection by on-screen channels list:

You can also select the required channel directly from on-screen channel list. This is

displayed using the STB's main menu.

4 Selection by EPG:

You can also select the required channel directly from electronic program guide (EPG).

For EPG details ,see previous page.

Channel list menu

1

Press to enter the main menu of the STB.

2

3

4

Press to highlight channel.

Press to enter the sub-menu.

Press to highlight the desired item and press

to confirm .

5

Press to exit.

Main Menu

Channel

Installation

Setup

Tools

Select OK Enter MENU Exit

Channel

TV Channel List

Radio Channel List

Delete All Favorites

Delete All Channels

Select OK Enter MENU Exit

8

CHANNEL

TV Channel list

1 Enter Channel menu.

2 Press to highlight TV channel list.

3 Press ,TV channel list appears.

4 Press to select channel group.

5 Press to preview the desired channel

6 Press to view the selected channel in full screen.

Favorite

1

In channel list menu, press numeric button "1" to setup Favorite item.

2 Press to move highlight between 8 favorite groups ,you can setup the desired channel to the selected favorite group.

3 Press to confirm,a favorite mark will be added.

4

5

Press on the marked favorite group to cancel favorite group,the mark will be cancel too.

EXIT

Press to and return to Channel list menu.

TV Channel List

All Channel

0001 BBC CHOICE

0002 BBC NEWS 2

Preview

1 Favorite 2

Select

Move

Group

3 Find

Page

4 Sort 5 Edit

OK Enter MENU Exit

TV Channel List

All Channel

0001 BBC CHOICE

Favorite 1

Favorite 2

Favorite 3

Favorite 4

Favorite 5

Favorite 6

Favorite 7

Favorite 8

Preview

1 Favorite 2

Select

Move

Group

3 Find

Page

4 Sort 5 Edit

OK Enter MENU Exit

Move

1

In channel list menu, press numeric button "2" , there will show a

"moving mark" in the right side of the selected channel.

2 Press to move the selected channel to the position that you want to place

TV Channel List

All Channel

0001 BBC CHOICE

0002 BBC NEWS 2

Preview

1 Favorite 2

Select

Move 3 Find

Group Page

4 Sort 5 Edit

OK Enter MENU Exit

Find

Use this menu to find a desired channel.

1

In channel list menu, press numeric button "3" to open Find menu.

2 Press to highlight the letter or numeric and press to input one by one.

3 After input each character, the program list on the left will search the channel according your input, and list the matched channel.

EXIT

4 Pressing to close "Find" and select channel from the channels list directly.

TV Channel List

All Channel

0001 BBC CHOICE

0002 BBC NEWS 2

Find

A

Preview

H I J K L M N

O P Q R S T U

V W X Y Z 1 2

3 4 5 6 7 8 9

0 ( ) @ & - +

/ SP ? DEL OK

1 Favorite 2

Select

Move 3 Find

Group Page

4 Sort 5 Edit

OK Enter MENU Exit

9

CHANNEL

TV Channel list (Continued)

Sort

1 In channel list menu, press numeric button "4" to open "Sort" menu.

2 Press to highlight sorting way you want and Press to confirm.

Default:

Name (A-Z):

Name (Z-A):

FTA:

Locked:

Sorting by scanning result.

Sorting in Alphabetical Order.

Sorting in Alphabetical Order.

Sieving out all free fare channels.

Accumulating all locked channels and list in the last of TV Channel List.

Edit

Use this menu to delete ,skip,lock and edit channel list.

In channel list menu, press numeric button "5" to open channel list edit menu.You will be asked to enter the password.The default

password is "0000".

TV Channel List

All Channel

0001 BBC CHOICE

Default

Name(A-Z)

Name(Z-A)

FTA

Lockd

Preview

1 Favorite 2

Select

Move 3 Find

Group Page

4 Sort

OK Enter

5 Edit

MENU Exit

TV Channel List

All Channel

0679 SZTV-M

Input Password

No Signal!

----

.

Delete:

In "Edit Channel" menu, press numeric button "1" can make a delete mark in the right side of the highlighted channel. After save and exit "Edit Channel" menu, the marked channel will be deleted.

Press "1" again to cancel delete channel.

1 Favorite 2

Select

Move

Group

3 Find

Page

4 Sort ok

5 Edit

Enter MENU Exit

Edit Channel

All Channel

0001 BBC CHOICE

0002 BBC NEWS 2 Preview

Skip:

In "Edit Channel" menu, press numeric button "2" can make a skip mark in the right side of the highlighted channel. After save and exit "Edit Channel" menu, the marked channel will be skip while you change the channel in full screen.

Press "2" button again to cancel the skip channel .

1 Delete

Select

2 Skip

Group

3 Lock

Page

4 Edit

MENU Exit

5 Del All

Lock:

In "Edit Channel" menu, press numeric button "3" can make a lock mark in the right side of the highlighted channel. After save and exit "Edit Channel" menu, the marked channel will be locked.STB will request you to input the password while you want to watch the locked channel.

Press "3" button again to cancel the lock channel .

10

CHANNEL

TV Channel list (Continued)

Edit:

Use edit to rename a channel.

Edit Channel

In "Edit Channel" menu, press numeric button "4" to open edit channel menu.Highlight name item and press to confirm.The mock keypad will be showed.

Input letter and numeric one by one by pressing and press to confirm.

All Channel

Video PID

Audio PID

PCR PID

Save

Exit

160

82

160

Preview

1 Delete

Select

2 Skip

Group

3 Lock 4 Edit 5

Page MENU Exit

Del All

After complete input,highlight "OK" on mock keypad to confirm, you change the name of channel successfully.

After modification, highlight "Save" item and press

to save the modified value and exit "Edit" mode.

Highlight "Exit" item and press to exit

"Edit" mode and won't save any modification.

NOTE:

"Video PID", "Audio PID" and "PCR PID" items are grey and can not be edited.

Del All:

In "Edit Channel" menu, press numeric button "5" can mark all the channel with delete mark.

After save and exit , all channels are deleted.

Press number "5"button again to cancel Del All function..

Radio Channel list

1

Enter Channel menu.

2 Press to highlight Radio channel list.

3 Press the ,Radio channel list appears.

4 Press to select channel group.

5 Press to preview channel logo of the desired channel

6 Press to listen the selected radio channel .

Radio Channel List

All Channel

0001 BBC PARLMNT

Preview

1 Favorite 2

Select

Move

Group

3 Find

Page

4

OK

Sort

Enter

5

MENU

Edit

Exit

NOTE:

Basically, the operation of "Radio Channel List" is same as "TV

Channel List", but there is one point different: In "Radio Channel

List" mode, there is no video information, so it will always display

Radio's logo in the right side preview window.

11

CHANNEL

Delete All Favorites

Use this menu to delete all favorite channels.

1 Enter Channel menu.

2 Press to highlight Delete

All Favorites item.

3

Press the ,you will be asked to input the password.

4

Input the password using the numeric buttons,a warning window is displayed.

Warning! Do you really want to delete all favorite channels?

Yes No

5 Highlight "Yes" to confirm,

Highlight"No" to cancel .

Channel

TV Channel List

Radio Channel List

Delete All Favorites

Delete All Channels

----

Select OK Enter MENU Exit

Delete All Channels

Use this menu to delete all channels.

1 Enter Channel menu.

2 Press to highlight Delete

All channels item.

3

Press the ,you will be asked to input the password.

4

Input the password using the numeric buttons,a warning window is displayed.

Warning! Do you really want to delete all channels?

Yes No

5 Highlight "Yes" to confirm,

Highlight"No" to cancel

Channel

TV Channel List

Radio Channel List

Delete All Favorites

Delete All Channels

----

Select OK Enter MENU Exit

12

SYSTEM SET-UP

Many aspects of your STB can be set to reflect your circumstances and preference. The SETTINGS menu screen is accessed from main menu.

System setup main menu

Use system menu to setup OSD Language, TV System, Start up

Service,Region and Time, Timer Setting, OSD Setting and

Parental Lock.

MENU

1

2

3

4

5

Press to enter the main menu of the STB.

Press to select "Setup".

Press to enter the sub-menu.

Press to highlight the desired item and press to confirm .

MENU

Press to exit.

Main Menu

Channel

Installation

Setup

Select OK Enter

Tools

MENU Exit

System Setup

OSD Language

TV System

Start up Service

Region and Time

Timer Setting

OSD Setting

Parental Lock

Select OK Enter MENU Exit

Use OSD Language to setup OSD Language , First Audio and

Second Audio language.

1 Enter "System Setup" menu, highlight "OSD Language".

2

Press ,the sub-menu appears.

3 Press to select the desired item and press to setup the desired language

4 Press to confirm.

OSD Language: To select your desired OSD language.

OSD Language

OSD Language

OSD Language

First Audio

Second Audio

English

English

English

Select Change MENU Exit

First Audio: Some channels have more than one audio language for choosing; use this function you can set the first audio for this channel. If the playing channel has the same audio as the "First Audio" you set, system will play this audio language as default. If the channel hasn't the suited audio language, then

the system will compare automatically with second audio language.

Second Audio: If the channel has no correspond audio with "First Audio" but have corres ponded audio with "Second Audio", system will play the second audio l anguage as default. If no audio language corresponds with the "Second

Audio", then the default language of current channel will be played automatically.

13

SYSTEM SET-UP

TV System

Use this menu to setup Display Mode,Aspect Ratio.Dolby Digital,

Video Output and LCN Mode.

1 Enter "System Setup" menu, highlight "TV System".

2

Press ,the sub-menu appears.

3 Press to select the desired item and press to setup the desired selection.

4 Press to confirm.

TV System

Display Mode

Aspect Ratio

Dolby Digital

Video Output

LCN Mode

Auto

4:3PS

Off

CVBS

Off

Select Change MENU Exit

Auto

PAL

NTSC

Auto switch to TV System

PAL TV System

NTSC TV System

Aspect Ratio: Aspect Mode is used for switching the screen aspect ratio mode.

Auto

4:3PS

4:3LB

16:9

Auto switch to Aspect Ratio

4:3 Pan Scan

4:3 Letter Box

16:9 Wide Screen

Dolby Digital: Dolby Digital to set AC3 on or off.

Video Output: Video Output is use for switching the video output mode.

RGB

CVBS

LCN Mode:

On

Off

Set to output RGB video signal

Set to output CVBS video signal

If LCN (Logical Channel Number)Select function is activated,You can't change the original number of TV channels by scanning .

Activate "LCN Select" function if there is LCN for the TV station of the country.

Deactivate "LCN Select" function.

14

SYSTEM SET-UP

Start up Service

Use this menu to setup a start up service when you power on STB.

1 Enter "System Setup" menu, highlight "Start up Service".

2 Press ,the sub-menu appears.

3 Press to select the desired item and press to setup the desired selection.

4 Press to confirm.

Boot on Service:

On

Off

Set up Start up Service On/Off.

Activate "Start up Service" function

Deactivate "Start up Service" function

Mode: Set up TV or Radio as Start up Service mode .

Start up Service: Set up a channel as Start up Service.

Start up Service

Boot on Service

Mode

Start up Service

On

TV

Select Change MENU Exit

Region and Time

Use this menu to setup country and time.

1 Enter "System Setup" menu, highlight "Region and Time".

2 Press ,the sub-menu appears.

3 Press to select the desired item and press to setup the desired selection.

4

5

Press to confirm.

MENU

Press to exit.

Region and Time

Region

GMT Usage

GMT Offset

Date

Time

Summer Time

Time Display

France

By Region

GMT+01:00

05/10/2005

11:23

Off

Off

Select

MENU Exit

Change 0~9 Input OK Enter

GMT Usage: This item is use for open the usage of GMT.There are three mode for using.

Off / User Define / By Region, press to switch.

GMT Offset: This item is valid only when the setting of "GMT Usage" is "Uesr Define".

Press to switch "GMT Offset" value. and the range is

"-12:00 ~ +12:00", increase each half hour progressively.

Date:

Time:

"Date" and "Time" items are valid only when the setting of "GMT Usage" is "Off".

Press to moving highlight and use number keys to input directly.

Summer Time: This item is valid only when the setting of "GMT Usage" is "By Region".

Press to switch between "On" and "Off".

Time Display: This function can control whether the time will be displayed on screen or not.

Press to switch between "On" and "Off".

15

SYSTEM SET-UP

Timer Setting

Various time can be set, such as program time, Sleep time.

1 Enter "System Setup" menu, highlight "Timer Setting".

2

Press ,the Timer Setting menu appears.

3 Press to select the desired item and press ,the sub-menu appears.

4

5

Press to highlight the desired item and press to set up the selection you want.

MENU

Press to exit.

Program Timer: This item is use for setting program timer you want to change to.

When you want to exit program timer,a saving window appears

Time Setting

Program Timer

Sleep Timer

Load Default Timer Setting

Select OK Enter MENU Exit

Timer

Current Date/Time

Timer Number

Timer Mode

Timer Service

Wakeup Channel

Wakeup Date

Wakeup Time

Duration

Select

06/10/2005 03:17

1

Off

Message

General

06/10/2005

03:10

01:00

Change 0~9 Input MENU Exit

For "Timer Service",if you select Message,a remind message will appear at setting timer. Press "OK" button to exit the message window.

Message mode:General/Birthday/Anniversary

Sleep Timer: You can set the STB to power off in 10 min,30min,

60min,90min and 120min automatically.

Sleep Timer

Sleep Time Off

Change MENU Exit

Load Default Timer Setting:

This function can clear all timer setting and return back to default timer setting.

If you enter this menu,you will be asked to input password

(the default password is "0000").

After input password, a confirmation window appears.

All Timers will be cleared, continue?

Highlight "Yes" or "No" and press"OK" to confirm or cancel.

Yes No

16

SYSTEM SET-UP

OSD Setting

You can set Subtitle On/Off,OSD Timeout, OSD Transparency, and load default OSD setting.

1 Enter "System Setup" menu, highlight "OSD Setting".

OSD Setting

2

Press ,the OSD Setting menu appears.

Subtitle Display

OSD Timeout

OSD Transparency

On

5

Off

3 Press to select the desired tem and press ,the sub-menu appears.

Load Default OSD Setting

4

5

Press to highlight the desired item and press to set up the selection you want.

MENU

Press to exit.

Subtitle Display: To set up the subtitle On/Off.

Select Change MENU Exit

OSD Timeout: When you switch channels in full screen, there will show up some information about current channel on the lower of the screen. Use "OSD Timeout " item to set upthe duration of these information show up on the screen.

Press to set the time from "1 second ~ 10seconds".

OSD Transparency: To set up the transparency of display of menu and the information show up on the screen.

Press to set the valule of transparency.

Load Default OSD Setting:

This function can clear all OSD setting and reset parameters as default value.

Parental Lock

The parental lock allows you to password protect channels,groups of menus or allow access to all menus.

1 Enter "System Setup" menu, highlight "Parental Lock".you will be asked to input password(the default password is"0000").

System Setup

2

After input the password,the parental lock menu appears.

3

4

Press to highlight the desired item and press to

set up the selection you want.

MENU

Press to exit.

OSD Language

Start up Service

Timer Setting

OSD Setting

Parental Lock

Select OK Enter MENU Exit

Menu Lock:

Yes

No

Set up the "Installation "Menu Lock/Unlock.

Lock the "Installation"menu.You must input the password if you want to enter any sub-menu of "Installation".

Unlock the "Installation"menu.

Channel Lock: Set up the channel Lock On/Off.

Yes

No

Activate channel lock function

Deactivate channel lock function

New Password: Use this item to change password.

17

Tools

In Tools menu ,you can see the software information, play game, Load factory default settings, upgrade software, help using remote control and enter welcome page for quick shortcut menu.

Tools main menu

1

2

3

4

5

MENU

Press to enter the main menu of the STB.

Press to select "Tools".

Press the to enter the sub-menu.

Press to highlight the desired item and press to confirm .

MENU

Press to exit.

Tools

Information

Game

Load Factory Default

Software Upgrade

Remote Control Help

Welcome Page

Select OK Enter MENU Exit

Main Menu

Channel

Installation

System Setup

Tools

Select OK Enter MENU Exit

Information

The "Information" menu can display some parameters of the software information in this STB.

1 Enter "Tools" menu, highlight "Information".

2

3

Press ,the information window appears.

MENU

Press to exit .

Information videoback 1.0.0

user db 1.0.0

MENU Exit

2006-08-21

2006-09-26

2005-12-23

2005-12-23

2005-12-23

2005-12-23

18

Tools

Load Factory Default

You can re-set the STB back to factory settings, clear all existed channels ae in this menu.

Tools

1 Enter "Tools" menu, highlight "Load Factory Default".

2

Press , you will be asked to input the password.

Information

Game

Input Password

Load Factory Default

3 Input the password using the numeric buttons(the default password is "0000"),a confirmation window is displayed.

Remote Control Help

WELCOME PAGE

Select OK Enter MENU Exit

This operation will load default and erase all the channels that user added,continue?

Yes No

4 Highlight "Yes" to confirm, STB will return back to factory settings and clear all channels.

5

6

Highlight "No" to cancel back to factory settings.

MENU

Press to Exit .

Remote Control Help

This function can show the description of each button on the screen.

1 Enter "Tools" menu, highlight "Remote Control Help".

2 Press ,the help menu appears.

3

4

Press any button on the remote control, the corresponding button on the screen will be highlight and show up a statement of this key on the right side on the screen.

EXIT

Press twice to exit.

Remote Control Help

Power

1

4

7

Menu

PG+

2

5

8

0

D/V

3

6

9

Exit

PG-

V-

Mute

Ch+

OK

Ch-

Pause

V+

FAV

Recall

EPG

TTX

Lang

T/R

Sub

Info

Audio Press "Exit" twice to exit

19

Veseg GmbH

Ostring 60 D-66740

Saarlouis-Fraulautern www.SEG.tv