INSTRUCTION MANUAL

Angle Grinder

9561CH

9561CVH

9562CH

9562CVH

9563C

9564C

9564CV

9565C

9565CV

DOUBLE INSULATION

007357

WARNING:

For your personal safety, READ and UNDERSTAND before using.

ENGLISH

SPECIFICATIONS

Model

Depressed center wheel diameter

Rated speed (n) / No load speed (n

0

Overall length

Net weight

Safety class

115 mm 125 mm 100 mm

289 mm

2.1 kg 2.3 kg 2.1 kg

/II

115 mm

299 mm

2.4 kg

125 mm

2.3 kg

Depressed center wheel diameter

Rated speed (n) / No load speed (n

0

)

Overall length

Net weight

115 mm

2.2 kg

125 mm 115 mm

2,800 - 12,000 min

289 mm

2.3 kg

-1

125 mm

299 mm

2.4 kg 2.4 kg

Safety class /II

• Due to our continuing programme of research and development, the specifications herein are subject to change without notice.

• Note: Specifications may differ from country to country.

• Weight according to EPTA-Procedure 01/2003

END202-6

The tool should be connected only to a power supply of

GEA005-3

Symbols

The following show the symbols used for the equipment.

Be sure that you understand their meaning before use.

･ Read instruction manual.

INSULATION

･ Wear

･ Only for EU countries

Intended use

Do not dispose of electric equipment together with household waste material!

The term "power tool" in the warnings refers to your

In observance of European Directive mains-operated (corded) power tool or battery-operated

2002/96/EC on waste electric and

(cordless) power tool. electronic equipment and its

Work area safety

implementation in accordance with

1. Keep work area clean and well lit. Cluttered or national law, electric equipment that dark areas invite accidents. have reached the end of their life must

2.

Do not operate power tools in explosive

be collected separately and returned to

atmospheres, such as in the presence of

an environmentally compatible recycling facility.

ENE048-1

Save all warnings and instructions for future reference.

flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.

3.

Keep children and bystanders away while

operating a power tool. Distractions can cause

The tool is intended for grinding, sanding and cutting of metal and stone materials without the use of water.

Power supply

ENF002-1

General Power Tool Safety

Warnings

WARNING Read all safety warnings and all

instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. you to lose control.

Electrical safety

4.

Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power

the same voltage as indicated on the nameplate, and

tools. Unmodified plugs and matching outlets will can only be operated on single-phase AC supply. They reduce risk of electric shock. are double-insulated in accordance with European

5.

Avoid body contact with earthed or grounded

Standard and can, therefore, also be used from sockets

surfaces such as pipes, radiators, ranges and

without earth wire.

refrigerators. There is an increased risk of

2

electric shock if your body is earthed or grounded.

6.

Do not expose power tools to rain or wet

conditions. Water entering a power tool will increase the risk of electric shock.

7.

Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges or

moving parts. Damaged or entangled cords increase the risk of electric shock.

8.

When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.

9.

If operating a power tool in a damp location is unavoidable, use a residual current device

(RCD) protected supply. Use of an RCD reduces the risk of electric shock.

10. Use of power supply via a RCD with a rated

residual current of 30mA or less is always recommended.

Personal safety

11. Stay alert, watch what you are doing and use

common sense when operating a power tool.

Do not use a power tool while you are tired or under the influence of drugs, alcohol or

medication. A moment of inattention while operating power tools may result in serious personal injury.

12. Use personal protective equipment. Always

wear eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.

13. Prevent unintentional starting. Ensure the

switch is in the off-position before connecting to power source and/or battery pack, picking

up or carrying the tool. Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents.

14. Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.

15. Do not overreach. Keep proper footing and

balance at all times. This enables better control of the power tool in unexpected situations.

16. Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing, and gloves

away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.

17. If devices are provided for the connection of

dust extraction and collection facilities,

ensure these are connected and properly used.

Use of dust collection can reduce dust-related hazards.

Power tool use and care

18. Do not force the power tool. Use the correct

power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.

19. Do not use the power tool if the switch does

not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.

20. Disconnect the plug from the power source

and/or the battery pack from the power tool before making any adjustments, changing

accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.

21. Store idle power tools out of the reach of

children and do not allow persons unfamiliar with the power tool or these instructions to

operate the power tool. Power tools are dangerous in the hands of untrained users.

22. Maintain power tools. Check for misalignment

or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the

power tool repaired before use. Many accidents are caused by poorly maintained power tools.

23. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.

24. Use the power tool, accessories and tool bits

etc. in accordance with these instructions, taking into account the working conditions

and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.

Service

25. Have your power tool serviced by a qualified

repair person using only identical replacement

parts. This will ensure that the safety of the power tool is maintained.

26. Follow instruction for lubricating and

changing accessories.

27. Keep handles dry, clean and free from oil and

grease.

GEB033-3

GRINDER SAFETY WARNINGS

Safety Warnings Common for Grinding, Sanding,

Wire Brushing, or Abrasive Cutting-Off Operations:

1.

This power tool is intended to function as a grinder, sander, wire brush or cut-off tool.

Read all safety warnings, instructions, illustrations and specifications provided with

this power tool. Failure to follow all instructions

3

listed below may result in electric shock, fire and/or serious injury.

2.

Operations such as polishing are not recommended to be performed with this

power tool. Operations for which the power tool was not designed may create a hazard and cause personal injury.

3.

Do not use accessories which are not specifically designed and recommended by

the tool manufacturer. Just because the accessory can be attached to your power tool, it does not assure safe operation.

4.

The rated speed of the accessory must be at least equal to the maximum speed marked on

the power tool. Accessories running faster than their rated speed can break and fly apart.

5.

The outside diameter and the thickness of your accessory must be within the capacity

rating of your power tool. Incorrectly sized accessories cannot be adequately guarded or controlled.

6.

The arbour size of wheels, flanges, backing pads or any other accessory must properly fit

the spindle of the power tool. Accessories with arbour holes that do not match the mounting hardware of the power tool will run out of balance, vibrate excessively and may cause loss of control.

7.

Do not use a damaged accessory. Before each use inspect the accessory such as abrasive wheels for chips and cracks, backing pad for cracks, tear or excess wear, wire brush for loose or cracked wires. If power tool or accessory is dropped, inspect for damage or install an undamaged accessory. After inspecting and installing an accessory, position yourself and bystanders away from the plane of the rotating accessory and run the power tool at maximum no-load speed for one

minute. Damaged accessories will normally break apart during this test time.

8.

Wear personal protective equipment.

Depending on application, use face shield, safety goggles or safety glasses. As appropriate, wear dust mask, hearing protectors, gloves and workshop apron capable of stopping small abrasive or

workpiece fragments. The eye protection must be capable of stopping flying debris generated by various operations . The dust mask or respirator must be capable of filtrating particles generated by your operation. Prolonged exposure to high intensity noise may cause hearing loss.

9.

Keep bystanders a safe distance away from work area. Anyone entering the work area

must wear personal protective equipment.

Fragments of workpiece or of a broken accessory may fly away and cause injury beyond immediate area of operation.

10. Hold power tool by insulated gripping

surfaces only, when performing an operation where the cutting accessory may contact

hidden wiring or its own cord. Cutting accessory contacting a "live" wire may make exposed metal parts of the power tool "live" and shock the operator.

11. Position the cord clear of the spinning

accessory. If you lose control, the cord may be cut or snagged and your hand or arm may be pulled into the spinning accessory.

12. Never lay the power tool down until the

accessory has come to a complete stop. The spinning accessory may grab the surface and pull the power tool out of your control.

13. Do not run the power tool while carrying it at

your side. Accidental contact with the spinning accessory could snag your clothing, pulling the accessory into your body.

14. Regularly clean the power tool’s air vents. The motor’s fan will draw the dust inside the housing and excessive accumulation of powdered metal may cause electrical hazards.

15. Do not operate the power tool near flammable

materials. Sparks could ignite these materials.

16. Do not use accessories that require liquid

coolants. Using water or other liquid coolants may result in electrocution or shock.

Kickback and Related Warnings

Kickback is a sudden reaction to a pinched or snagged rotating wheel, backing pad, brush or any other accessory. Pinching or snagging causes rapid stalling of the rotating accessory which in turn causes the uncontrolled power tool to be forced in the direction opposite of the accessory’s rotation at the point of the binding.

For example, if an abrasive wheel is snagged or pinched by the workpiece, the edge of the wheel that is entering into the pinch point can dig into the surface of the material causing the wheel to climb out or kick out. The wheel may either jump toward or away from the operator, depending on direction of the wheel’s movement at the point of pinching. Abrasive wheels may also break under these conditions.

Kickback is the result of power tool misuse and/or incorrect operating procedures or conditions and can be avoided by taking proper precautions as given below. a) Maintain a firm grip on the power tool and

position your body and arm to allow you to resist kickback forces. Always use auxiliary handle, if provided, for maximum control over

kickback or torque reaction during start-up.

4

The operator can control torque reactions or kickback forces, if proper precautions are taken. b) Never place your hand near the rotating

accessory. Accessory may kickback over your hand. c) Do not position your body in the area where

power tool will move if kickback occurs.

Kickback will propel the tool in direction opposite to the wheel’s movement at the point of snagging. d) Use special care when working corners,

sharp edges etc. Avoid bouncing and snagging

the accessory. Corners, sharp edges or bouncing have a tendency to snag the rotating accessory and cause loss of control or kickback. e) Do not attach a saw chain woodcarving

blade or toothed saw blade. Such blades create frequent kickback and loss of control

Safety Warnings Specific for Grinding and Abrasive

Cutting-Off Operations:

a) Use only wheel types that are recommended

for your power tool and the specific guard

designed for the selected wheel. Wheels for which the power tool was not designed cannot be adequately guarded and are unsafe. b) The guard must be securely attached to the

power tool and positioned for maximum safety, so the least amount of wheel is exposed

towards the operator. The guard helps to protect operator from broken wheel fragments and accidental contact with wheel. c) Wheels must be used only for recommended

applications. For example: do not grind with

the side of cut-off wheel. Abrasive cut-off wheels are intended for peripheral grinding, side forces applied to these wheels may cause them to shatter. d) Always use undamaged wheel flanges that

are of correct size and shape for your selected

wheel. Proper wheel flanges support the wheel thus reducing the possibility of wheel breakage.

Flanges for cut-off wheels may be different from grinding wheel flanges. e) Do not use worn down wheels from larger

power tools. Wheel intended for larger power tool is not suitable for the higher speed of a smaller tool and may burst.

Additional Safety Warnings Specific for Abrasive

Cutting-Off Operations:

a) Do not “jam” the cut-off wheel or apply

excessive pressure. Do not attempt to make an

excessive depth of cut. Overstressing the wheel increases the loading and susceptibility to twisting or binding of the wheel in the cut and the possibility of kickback or wheel breakage. b) Do not position your body in line with and

behind the rotating wheel. When the wheel, at the point of operation, is moving away from your body, the possible kickback may propel the spinning wheel and the power tool directly at you. c) When wheel is binding or when interrupting

a cut for any reason, switch off the power tool and hold the power tool motionless until the wheel comes to a complete stop. Never attempt to remove the cut-off wheel from the cut while the wheel is in motion otherwise kickback may

occur. Investigate and take corrective action to eliminate the cause of wheel binding d) Do not restart the cutting operation in the

workpiece. Let the wheel reach full speed and

carefully reenter the cut. The wheel may bind, walk up or kickback if the power tool is restarted in the workpiece. e) Support panels or any oversized workpiece

to minimize the risk of wheel pinching and

kickback. Large workpieces tend to sag under their own weight. Supports must be placed under the workpiece near the line of cut and near the edge of the workpiece on both sides of the wheel. f) Use extra caution when making a “pocket

cut” into existing walls or other blind areas.

The protruding wheel may cut gas or water pipes, electrical wiring or objects that can cause kickback.

Safety Warnings Specific for Sanding Operations:

a) Do not use excessively oversized sanding

disc paper. Follow manufacturers recommendations, when selecting sanding

paper. Larger sanding paper extending beyond the sanding pad presents a laceration hazard and may cause snagging, tearing of the disc or kickback.

Safety Warnings Specific for Wire Brushing

Operations:

a) Be aware that wire bristles are thrown by the

brush even during ordinary operation. Do not overstress the wires by applying excessive

load to the brush. The wire bristles can easily penetrate light clothing and/or skin. b) If the use of a guard is recommended for

wire brushing, do not allow interference of the

wire wheel or brush with the guard. Wire wheel or brush may expand in diameter due to work load and centrifugal forces.

Additional safety warnings:

17. When using depressed centre grinding wheels,

be sure to use only fiberglass-reinforced wheels.

18. Be careful not to damage the spindle, the

flange (especially the installing surface) or the lock nut. Damage to these parts could result in wheel breakage.

5

19. Make sure the wheel is not contacting the

workpiece before the switch is turned on.

20. Before using the tool on an actual workpiece,

let it run for a while. Watch for vibration or wobbling that could indicate poor installation or a poorly balanced wheel.

21. Use the specified surface of the wheel to

perform the grinding.

22. Watch out for flying sparks. Hold the tool so

that sparks fly away from you and other persons or flammable materials.

23. Do not leave the tool running. Operate the tool

only when hand-held.

24. Do not touch the workpiece immediately after

operation; it may be extremely hot and could burn your skin.

25. Always be sure that the tool is switched off

and unplugged or that the battery cartridge is removed before carrying out any work on the tool.

26. Observe the instructions of the manufacturer

for correct mounting and use of wheels.

Handle and store wheels with care.

27. Do not use separate reducing bushings or

adaptors to adapt large hole abrasive wheels.

28. Use only flanges specified for this tool.

29. For tools intended to be fitted with threaded

hole wheel, ensure that the thread in the wheel is long enough to accept the spindle length.

30. Check that the workpiece is properly

supported.

31. Pay attention that the wheel continues to

rotate after the tool is switched off.

32. If working place is extremely hot and humid,

or badly polluted by conductive dust, use a short-circuit breaker (30 mA) to assure operator safety.

33. Do not use the tool on any materials

containing asbestos.

34. Do not use water or grinding lubricant.

35. Ensure that ventilation openings are kept clear

when working in dusty conditions. If it should become necessary to clear dust, first disconnect the tool from the mains supply

( use non metallic objects ) and avoid damaging internal parts.

36. When use cut-off wheel, always work with the

dust collecting wheel guard required by domestic regulation.

37. Cutting discs must not be subjected to any

lateral pressure.

SAVE THESE INSTRUCTIONS.

WARNING:

DO NOT let comfort or familiarity with product

(gained from repeated use) replace strict adherence to safety rules for the subject product. MISUSE or failure to follow the safety rules stated in this instruction manual may cause serious personal injury.

FUNCTIONAL DESCRIPTION

CAUTION:

•

Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool.

Shaft lock

1

1. Shaft lock

007358

CAUTION:

•

Never actuate the shaft lock when the spindle is moving. The tool may be damaged.

Press the shaft lock to prevent spindle rotation when installing or removing accessories.

Switch action

1. Slide switch

1

007359

For tools with the lock-on switch

CAUTION:

•

Before plugging in the tool, always check to see that the slide switch actuates properly and returns to the "OFF" position when the rear of the slide switch is depressed.

To start the tool, slide the slide switch toward the "I (ON)" position. For continuous operation, press the front of the slide switch to lock it.

To stop the tool, press the rear of the slide switch, then

6

slide it toward the "O (OFF)" position.

For tools without the lock-on switch

•

CAUTION:

Before plugging in the tool, always check to see that the slide switch actuates properly and returns to the "OFF" position when released.

To start the tool, slide the slide switch toward the "I (ON)" position.

To stop the tool, release the slide switch toward the "O

(OFF)" position.

Speed adjusting dial

For 9561CVH, 9562CVH, 9564CV, 9565CV

1. Speed adjusting dial

•

Overload protector

When the tool would be employed over the admissible load, it will stop automatically to protect the motor and wheel. When the load will come to the admissible level again, the tool can be started automatically.

ASSEMBLY

CAUTION:

•

Always be sure that the tool is switched off and unplugged before carrying out any work on the tool.

Installing side grip (handle)

2

1

001046

The rotating speed can be changed by turning the speed adjusting dial to a given number setting from 1 to 5.

Higher speed is obtained when the dial is turned in the direction of number 5. And lower speed is obtained when it is turned in the direction of number 1.

Refer to the below table for the relationship between the number settings on the dial and the approximate rotating speed.

Number

1

2

3

4

5 min

-1

(R.P.M.)

2,800

4,000

6,500

9,000

12,000

010478

•

•

CAUTION:

If the tool is operated continuously at low speeds for a long time, the motor will get overloaded and heated up.

The speed adjusting dial can be turned only as far as 5 and back to 1. Do not force it past 5 or 1, or the speed adjusting function may no longer work.

The tools equipped with electronic function are easy to operate because of the following features.

•

Electronic constant speed control

•

Possible to get fine finish, because the rotating speed is kept constantly even under the loaded condition.

Soft start feature

Soft start because of suppressed starting shock.

7

007360

CAUTION:

•

Always be sure that the side grip is installed securely before operation.

Screw the side grip securely on the position of the tool as shown in the figure.

Installing or removing wheel guard

For tool with locking screw type wheel guard

1

1. Wheel guard

2. Bearing box

3. Screw

3

007566

2

007564

2

1

3

1. Wheel guard

2. Bearing box

3. Screw

•

CAUTION:

The wheel guard must be fitted on the tool so that the closed side of the guard always points toward the operator.

Mount the wheel guard with the protrusion on the wheel guard band aligned with the notch on the bearing box.

Then rotate the wheel guard around 180 degrees clockwise or counterclockwise. Be sure to tighten the screw securely.

To remove wheel guard, follow the installation procedure in reverse.

For tool with clamp lever type wheel guard

1

1. Wheel guard

2. Bearing box

3. Screw

4. Lever

2

3

4

002980

1 1. Screw

Mount the inner flange onto the spindle. Fit the wheel/disc on the inner flange and screw the lock nut onto the spindle.

To tighten the lock nut, press the shaft lock firmly so that the spindle cannot revolve, then use the lock nut wrench and securely tighten clockwise.

1

1. Lock nut wrench

2. Shaft lock

2

007363

To remove the wheel, follow the installation procedure in reverse.

Installing or removing dust cover attachment

(Optional accessory)

•

WARNING:

Always be sure that the tool is switched off and unplugged before installing or removing the dust cover attachment. Failure to do so causes damage to the tool or a personal injury.

There are three types of dust cover attachment and each is used in one of different positions.

1. Marking A

002981

Pull the lever in the direction of the arrow after loosening the screw. Mount the wheel guard with the protrusion on the wheel guard band aligned with the notch on the bearing box. Then rotate the wheel guard around 180°.

Fasten it with the screw after pulling lever in the direction of the arrow for the working purpose. The setting angle of the wheel guard can be adjusted with the lever.

To remove wheel guard, follow the installation procedure in reverse.

Installing or removing depressed center grinding wheel/Multi-disc (accessory)

1

2

3

1. Lock nut

2. Depressed center grinding wheel/Multi-disc

3. Inner flange

005259

005260

1

1

1. Marking B

007362

8

1. Marking C

1

005261

Place the dust cover attachment so that the side of the dust cover attachment with the marking (A,B or C) faces towards the tool head. Snap the pins of the dust cover attachment in the vent.

1

1. Pin

2. Vent

•

CAUTION:

After operation, always switch off the tool and wait until the wheel has come to a complete stop before putting the tool down.

Grinding and sanding operation

ALWAYS hold the tool firmly with one hand on housing and the other on the side handle. Turn the tool on and then apply the wheel or disc to the workpiece.

In general, keep the edge of the wheel or disc at an angle of about 15 degrees to the workpiece surface.

During the break-in period with a new wheel, do not work the grinder in the B direction or it will cut into the workpiece. Once the edge of the wheel has been rounded off by use, the wheel may be worked in both A and B direction.

A B

2

005262

Dust cover attachment can be removed by hand.

NOTE:

•

Clean out the dust cover attachment when it is clogged with dust or foreign matters. Continuing operation with a clogged dust cover attachment will damage the tool.

OPERATION

•

•

•

•

•

WARNING:

It should never be necessary to force the tool. The weight of the tool applies adequate pressure.

Forcing and excessive pressure could cause dangerous wheel breakage.

ALWAYS replace wheel if tool is dropped while grinding.

NEVER bang or hit grinding disc or wheel onto work.

Avoid bouncing and snagging the wheel, especially when working corners, sharp edges etc. This can cause loss of control and kickback.

NEVER use tool with wood cutting blades and other sawblades. Such blades when used on a grinder frequently kick and cause loss of control leading to personal injury.

15

007364

MAINTENANCE

•

•

CAUTION:

Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance.

Never use gasoline, benzine, thinner, alcohol or the like. Discoloration, deformation or cracks may result.

1

1. Exhaust vent

2. Inhalation vent

2

007365

The tool and its air vents have to be kept clean.

Regularly clean the tool's air vents or whenever the vents start to become obstructed.

To maintain product SAFETY and RELIABILITY, repairs, carbon brush inspection and replacement, any other maintenance or adjustment should be performed by

Makita Authorized Service Centers, always using Makita replacement parts.

9

ACCESSORIES

CAUTION:

•

These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose.

If you need any assistance for more details regarding these accessories, ask your local Makita Service Center.

•

•

•

•

•

•

•

•

•

•

•

•

•

Wheel guard (Wheel cover)

Inner flange

Depressed center wheels

Lock nut (For depressed center wheel)

Rubber pad

Abrasive discs

Lock nut (For abrasive disc)

Lock nut wrench

Wire cup brush

Wire bevel brush 85

Side grip

Diamond wheel

Dust collecting wheel guard

10

11

884674A3

Makita Corporation

12