Samsung COLOR TELEVISION Specifications

COLOR TELEVISION RECEIVER

Chassis : K15A (H)

Model: CT2088BL6X/XAP

CT1488BL6X/XAP

COLOR TELEVISION RECEIVER CONTENTS

1.

Precautions

2.

Specifications

3.

Alignment and Adjustments

4.

Troubleshooting

5.

Exploded Views and Parts List

6.

Electrical Parts List

7.

Block Diagram

8.

Wiring Diagrams

9.

Schematic Diagrams

ELECTRONICS

© Samsung Electronics Co., Ltd. APR. 2000

Printed in Korea

3K15A-8801

Precautions

1. Precautions

Follow these safety, servicing and ESD precautions to prevent damage and protect against potential hazards such as electrical shock and X-rays.

1-1 Safety Precautions

1. Be sure that all of the built-in protective devices are replaced. Restore any missing protective shields.

2. When reinstalling the chassis and its assemblies, be sure to restore all protective devices, including: nonmetallic control knobs and compartment covers.

3. Make sure that there are no cabinet openings through which people—particularly children—might insert fingers and contact dangerous voltages. Such openings include the spacing between the picture tube and the cabinet mask, excessively wide cabinet ventilation slots, and improperly fitted back covers.

If the measured resistance is less than 1.0

megohm or greater than 5.2 megohms, an abnormality exists that must be corrected before the unit is returned to the customer.

4. Leakage Current Hot Check (Figure 1-1):

Warning: Do not use an isolation transformer during this test. Use a leakagecurrent tester or a metering system that complies with American National Standards

Institute (ANIS C101.1, Leakage Current for

Appliances), and Underwriters Laboratories

(UL Publication UL1410, 59.7).

5. With the unit completely reassembled, plug the AC line cord directly into the power outlet. With the unit’s AC switch first in the

ON position and then OFF, measure the current between a known earth ground (metal water pipe, conduit, etc.) and all exposed metal parts, including: antennas, handle brackets, metal cabinets, screwheads and control shafts. The current measured should not exceed 0.5 milliamp. Reverse the powerplug prongs in the AC outlet and repeat the test.

DEVICE

UNDER

TEST

TEST ALL

EXPOSED METAL

SURFACES

3-WIRE CORD

ALSO TEST WITH

PLUG REVERSED

(USING AC ADAPTER

PLUG AS REQUIRED)

LEAKAGE

CURRENT

TESTER

(READING SHOULD

NOT BE ABOVE

0.5mA)

EARTH

GROUND

Fig. 1-1 AC Leakage Test

6. Antenna Cold Check:

With the unit’s AC plug disconnected from the

AC source, connect an electrical jumper across the two AC prongs. Connect one lead of the ohmmeter to an AC prong. Connect the other lead to the coaxial connector.

7. X-ray Limits:

The picture tube is especially designed to prohibit X-ray emissions. To ensure continued

X-ray protection, replace the picture tube only with one that is the same type as the original.

Carefully reinstall the picture tube shields and mounting hardware; these also provide X-ray protection.

8. High Voltage Limits:

High voltage must be measured each time servicing is done on the B+, horizontal deflection or high voltage circuits. Correct operation of the X-ray protection circuits must be reconfirmed whenever they are serviced.

(X-ray protection circuits also may be called

“horizontal disable” or “hold-down”.)

Heed the high voltage limits. These include the X–ray Protection Specifications Label, and the Product Safety and X-ray Warning Note on the service data schematic.

Samsung Electronics 1-1

Precautions

1-1 Safety Precautions (Continued)

9. High voltage is maintained within specified limits by close-tolerance, safety-related components and adjustments. If the high voltage exceeds the specified limits, check each of the special components.

10. Design Alteration Warning:

Never alter or add to the mechanical or electrical design of this unit. Example: Do not add auxiliary audio or video connectors. Such alterations might create a safety hazard. Also, any design changes or additions will void the manufacturer’s warranty.

11. Hot Chassis Warning:

Some TV receiver chassis are electrically connected directly to one conductor of the AC power cord. If an isolation transformer is not used, these units may be safely serviced only if the AC power plug is inserted so that the chassis is connected to the ground side of the

AC source.

To confirm that the AC power plug is inserted correctly, do the following: Using an AC voltmeter, measure the voltage between the chassis and a known earth ground. If the reading is greater than 1.0V, remove the AC power plug, reverse its polarity and reinsert.

Re-measure the voltage between the chassis and ground.

12. Some TV chassis are designed to operate with

85 volts AC between chassis and ground, regardless of the AC plug polarity. These units can be safely serviced only if an isolation transformer inserted between the receiver and the power source.

13. Some TV chassis have a secondary ground system in addition to the main chassis ground.

This secondary ground system is not isolated from the AC power line. The two ground systems are electrically separated by insulating material that must not be defeated or altered.

14. Components, parts and wiring that appear to have overheated or that are otherwise damaged should be replaced with parts that meet the original specifications. Always determine the cause of damage or overheating, and correct any potential hazards.

1-2

15. Observe the original lead dress, especially near the following areas: Antenna wiring, sharp edges, and especially the AC and high voltage power supplies. Always inspect for pinched, out-of-place, or frayed wiring. Do not change the spacing between components and the printed circuit board. Check the AC power cord for damage. Make sure that leads and components do not touch thermally hot parts.

16. Picture Tube Implosion Warning:

The picture tube in this receiver employs

“integral implosion” protection. To ensure continued implosion protection, make sure that the replacement picture tube is the same as the original.

17. Do not remove, install or handle the picture tube without first putting on shatterproof goggles equipped with side shields. Never handle the picture tube by its neck. Some

“in-line” picture tubes are equipped with a permanently attached deflection yoke; do not try to remove such “permanently attached” yokes from the picture tube.

18. Product Safety Notice:

Some electrical and mechanical parts have special safety-related characteristics which might not be obvious from visual inspection.

These safety features and the protection they give might be lost if the replacement component differs from the original—even if the replacement is rated for higher voltage, wattage, etc.

Components that are critical for safety are indicated in the circuit diagram by shading,

( ) or ( ).

Use replacement components that have the same ratings, especially for flame resistance and dielectric strength specifications.

A replacement part that does not have the same safety characteristics as the original might create shock, fire or other hazards.

Samsung Electronics

Precautions

1-2 Servicing Precautions

Warning 1 : First read the “Safety Precautions” section of this manual. If some unforeseen circumstance creates a conflict between the servicing and safety precautions, always follow the safety precautions.

Warning 2 : An electrolytic capacitor installed with the wrong polarity might explode.

1. Servicing precautions are printed on the cabinet. Follow them.

2. Always unplug the unit’s AC power cord from the AC power source before attempting to: (a)

Remove or reinstall any component or assembly, (b) Disconnect an electrical plug or connector, (c) Connect a test component in parallel with an electrolytic capacitor.

3. Some components are raised above the printed circuit board for safety. An insulation tube or tape is sometimes used. The internal wiring is sometimes clamped to prevent contact with thermally hot components. Reinstall all such elements to their original position.

4. After servicing, always check that the screws, components and wiring have been correctly reinstalled. Make sure that the portion around the serviced part has not been damaged.

5. Check the insulation between the blades of the

AC plug and accessible conductive parts

(examples: metal panels, input terminals and earphone jacks).

6. Insulation Checking Procedure: Disconnect the power cord from the AC source and turn the power switch ON. Connect an insulation resistance meter (500V) to the blades of the AC plug.

The insulation resistance between each blade of the AC plug and accessible conductive parts

(see above) should be greater than 1 megohm.

7. Never defeat any of the B+ voltage interlocks.

Do not apply AC power to the unit (or any of its assemblies) unless all solid-state heat sinks are correctly installed.

8. Always connect a test instrument’s ground lead to the instrument chassis ground before connecting the positive lead; always remove the instrument’s ground lead last.

9. When some parts inside the optical engine

(except lamp) are damaged, replace the whole optical engine.


Precautions

1-3 Precautions for Electrostatically Sensitive Devices (ESDs)

1. Some semiconductor (“solid state”) devices are easily damaged by static electricity. Such components are called Electrostatically

Sensitive Devices (ESDs); examples include integrated circuits and some field-effect transistors. The following techniques will reduce the occurrence of component damage caused by static electricity.

2. Immediately before handling any semicon ductor components or assemblies, drain the electrostatic charge from your body by touching a known earth ground. Alternatively, wear a discharging wrist-strap device. (Be sure to remove it prior to applying power— this is an electric shock precaution.)

3. After removing an ESD-equipped assembly, place it on a conductive surface such as aluminum foil to prevent accumulation of electrostatic charge.

4. Do not use freon-propelled chemicals. These can generate electrical charges that damage

ESDs.

5. Use only a grounded-tip soldering iron when soldering or unsoldering ESDs.

6. Use only an anti-static solder removal device.

Many solder removal devices are not rated as

“anti-static”; these can accumulate sufficient electrical charge to damage ESDs.

7. Do not remove a replacement ESD from its protective package until you are ready to install it. Most replacement ESDs are packaged with leads that are electrically shorted together by conductive foam, aluminum foil or other conductive materials.

8. Immediately before removing the protective material from the leads of a replacement ESD, touch the protective material to the chassis or circuit assembly into which the device will be installed.

9. Minimize body motions when handling unpackaged replacement ESDs. Motions such as brushing clothes together, or lifting a foot from a carpeted floor can generate enough static electricity to damage an ESD.

1-4 Samsung Electronics

2. Specifications

2-1 Specifications

Television System

Picture Tube

Power Requirement

Operating System

Tuning Ranges

Antenna Input Impedance

Intermediate Frequency

Speaker Impedance

14" / 20" / 21" NTSC COLOR TV SIGNAL

A34KQV42X / A48KRD82X (H) / A51KQJ63X

AC 120V, 60Hz /AC 100 ~ 240, 50Hz, 60Hz

REMOCON SYSTEM (SZM370TH)

VHF CH : 2-13, UHF CH : 14-69, CABLE CH : 1,14-125

75 ohm UNBALANCED TYPE FOR VHF/UHF

PICTURE 45.75MHz, SOUND 41.25MHz,

COLOR SUB CARRIER 42.17MHz

Dual : 8 ohm 6W x 2

Specifications


MEMO


Alignment and Adjustments

3. Alignment and Adjustments

3-1 Service Mode Adjustments

3-1-1 Service Mode Menus

Since there are no VRs in the K15A chassis, all adjustments after parts replacement must be done in the Service Mode. Service Mode adjustments are necessary when either the

EEPROM (IC902) or the CRT is replaced.

3-1-2 Entering the Service Mode

Press the following transmitter keys while in STAND-BY mode:

MUTE—>1—>8—>2—>POWER

“Factory Mode Menu” is displayed

SCR

STT

GG

BG

AGC

VCO

SBT

SCT

ADJUSTMENT

PATTERN

OPTION

RESET

<---selected (violet)

Enter Service Mode using the Volume

+,- keys. Service Mode Menu:

XX

XX

XX

XX

XX

XXX

XXX

XXX

RC

GC

BC

VA

VS

HS

XX

XX

SS XX

SVC : MUTE

XXX

XXX

XX

XX

Select a mode to be adjusted, using the channel down key. Example: VCO.

AGC

VCO

SBT

SCT

SCR

STT

GG

BG

XX

XX

XX

XX

XX

XXX

XXX

XXX

RC

GC

BC

XXX

XXX

XX

VA

VS

HS

SS

XX

XX

XX

XX

SVC : MUTE

Samsung Electronics

Change the data with “Volume +, - “ keys.

VCO 71

AGC

VCO

SBT

SCT

SCR

STT

GG

BG

Return to the Service mode by pressing

MENU.

XX

XX

XX

XX

XX

XXX

XXX

XXX

RC

GC

BC

VA

VS

HS

XXX

XXX

XX

XX

XX

XX

SS XX

SVC : MUTE

Return to the Factory mode via the MENU key.

ADJUSTMENT

PATTERN

OPTION

RESET

Press POWER to enter the Stand-by mode.

3-1


3-1-3 Adjustment in Option Mode

This adjustment is necessary whenever the

EEPROM is replaced. Input data (as marked on the back cabinet).

ADJUSTMENT

PATTERN

OPTION

RESET

Select “SET OPTION” by pressing the

ADJUSTMENT

PATTERN

OPTION

RESET

Press the Volume +, - keys to enter the set

Option mode.

BYTE 0 : 0 0

BYTE 1 : 0 4

Press MENU to go back to the factory mode.

ADJUSTMENT

PATTERN

OPTION

RESET

ADJUSTMENT

PATTERN

OPTION

RESET

Press volume + key.

POWER

OFF

3-1-4 Service Mode Adjustments

ADJUSTMENT

PATTERN

OPTION

RESET

1. The Pattern Adjustment is done only in the factory. Do not attempt to readjust it.

2. Refer to 3-2 for other adjustments.

3. Set OPTION data.

3-1-5 Service Mode Adjustment Ratings

No Item Function Range

Initalized

MICOM Data

0~63 50 1 AGC RF AGC Adjustment

2 VCO PIF VCO Adjustment

3 SCT SUB-CONTRAST Adjustment

4 SCR SUB-COLOR Adjustment

5 STT SUB-TINT Adjustment

6 RC RED-CUT OFF Adjustment

7 GC GREEN-CUT OFF Adjustment

0~127

0~63

0~27

0~27

0~255

0~255

0~255 8 BC BLUE-CUT OFF Adjustment

9 SVC Input a Horiz line pattern

10 GG GREEN-GAIN Adjustment

11 BG BLUE-GAIN Adjustment

12 SBT SUB-BRIGHTNESS Adjustment

13 VA VERTICAL SIZE Adjustment

14 VS VERTICAL CENTER Adjustment 0

15 HS HORIZONTAL Phase Adjustment 0~31

16 SS SUB-SHARPNESS Adjustment 0~31

0~255

0~255

0~63

0~63

63

48

13

7

0

0

0

127

127

31

39

0

15

4

Note : The initial MICOM data values take effect when IC902 is replaced.



3-2 Alignment and Adjustment

3-2-1 General Alignment Instructions

1. Usually, a color TV needs only slight touch-up adjustment upon installation. Check the basic characteristics such as picture height, focus and a horizontal and vertical sync.

2. Observe the picture and check for good back and white details. There should be no objectionable color shading: If color shading is present, demagnetize the receiver. If color shading persists, perform purity and convergence adjustments described below.

3. To protect against shock hazard, use an isolation transformer.

3-2-2 Power Supply Check

Check the following:

A: Power plug is connected; “Stand-by” mode

B: Power On when “Power ON” button is pressed

C: Power On by FBT Each supply is marked on its lead-in wire. ( )

3-2-3 Focus Adjustment

Adjust the focus control on the FBT for well defined scanning lines.

3-2-4 Fail Safe Circuit Check (FS) (OPTION)

1. The failsafe check must be the final step in servicing.

2. Turn the power switch ON and adjust customer controls for normal operation.

3. Temporarily short pin X to pin R on the main board (RX06, RX04) with a jumper wire.

Raster will disappear.

4. The TV must remain in this state even after removing the jumper wire. This shows that the failsafe circuit is working properly.

5. To recover picture and sound, temporarily turn off the TV and allow the failsafe circuit more than 30 seconds to reset. Then switch power ON to produce normal picture and sound.

3-2-5 IC902 Replacement

1. When IC902 is replaced, all values are reset to

“Initialized MICOM Data” and readjustment is necessary.

2. Press the POWER button 10 seconds after plug-in.

3. To enter the Service Mode, refer to Fig. 3-1

(Service Mode Adjustment).

3-2-6 PIF VCO Adjustment

1. Use a Pattern Generator or an off-air signal.

2. Open pin 11 of Micom (IC901) or one side of lead pin for R237.

3. Adjust VCO in the service mode to set IC101

Pin 44 (AFT) to 2.5V ± 0.4V.

4. Connect the opened site.

3-2-7 RF-AGC Adjustment

1.

Input a PHILLIPS pattern.

2.

Set the input signal to 60 dB.

3.

Enter into the AGC in the service mode.

4.

Adjust AGC until color bar noise disappears.



3-2-8 Sub-Contrast Adjustment

1. Input a gray scale pattern. Use a pattern generator (PM5518).

2.

Short D208 to switch off the ABL feed-back.

3.

Check CN201 R-OUT with an oscilloscope.

4.

Set RC, BC, GC data to 0 in the Service Mode.

5. Adjust SCT to 2.40 ± 0.1Vp-p

3-2-10 Sub-Color Adjustment

1. Do sub-color adjustment after the Sub-

Contrast and Sub-Tint adjustments.

2. D208 should still be shorted. The ABL should still be switched OFF.

3. Input a color bar pattern. Use a pattern generator (PM5518).

4. Check CN201 R-OUT (use an oscilloscope).

5. Ensure that the RC, GC and BC data are 0.

BG are 140 and GG should be 90.

6. Adjust SCR to 2.4 ± 0.1Vp-p (black and red levels).

7. Remove the short across D208 and restore

ABL.

6. Remove the short across D208 and restore

ABL.

3-2-9 Sub-Tint Adjustment

1.

Input a rainbow pattern.

2.

Check CN201 B-OUT with an oscilloscope.

3. Adjust STT in the service mode until the 6th peak is the highest and the 5th and 7th peaks have equal heights.

1

2

3

4

5

6

7 8

9

10


3-2-11 White Balance Adjustment

3-2-11 (A) LOW-LIGHT ADJUSTMENTS

1. Input either a lion head or “pure white” color pattern.

2. Operate the receiver for 30 minutes.

3. Check the data in the service mode:

RC, GC, BC are 0 and SB is 16;

Steps BG are 90 and GG are 140.

4. Enter the horizontal line mode by pressing the MUTE key.

5. Adjust the screen VR on the FBT until a dim colored line (red,green or blue) appears on the screen.

dim colored line (red, green or blue) in the

7.

Exit the horizontal line via the MUTE key.

3-2-11 (B) HIGH-LIGHT ADJUSTMENTS

1. Input a high-light pattern

2. Adjust GG,BG in the Service Mode.

3. Recheck in low light.

3-2-12 Sub-Brightness Adjustment

1. Input a Toshiba pattern.

2. Warm up the receiver for 10 minutes.

3. Enter the Service Mode and set SB to the point where the 5th point is brighter in the gray scale.

W

5 4 3 2 1


3-2-13 Vertical Size Adjustment

1. Input a lion head pattern.

2. After the vertical center adjustment, enter into the service mode.

3. Adjust VA so that the each top and bottom of the screen is 4.0. If the top and bottom values are different, adjust VA so that the sum of the two values is 8.0.

3-2-14 Horizontal Size Adjustment

1. Receive a lion head pattern.

2. Enter into the service mode.

3. Adjust HS to symmetrized right and left.

3-2-15 When CRT Is Replaced

Do the following adjustments after the basic purity and convergence adjustments.

1. White Balance

2. Sub-brightness

3. Vertical Size

4. Horizontal Size

5. Fail safe (should be the final step).


BYTE:1

D7

D6

D5

D4

D3

D2

D1

D0

3-3 Option Byte Table

Micom : SZM370TH

Note: The option bytes are adjusted in the Service mode.

BYTE:0

D7

D6

D5

NAME

WIDE

AFT

AUTO

POWER ON

0

Not Used

Analog (Tuner Input)

FUNCTION

1

Used

Digital (1 Chip Input)

Not Used Used

D4

D3

D2

D1

AUTO

SOUND MUTE

TV/Video

AUTO

POWER OFF

Sound Mute

(during no signal)

TV/Video

Not Used

No Sound Mute

(during no signal)

Video Only

Power Off

(after 15 minute) during no signal

D0 CATV AIR/STD/HRC/IRC AIR/STD/HRC/AFN

FUNCTION

NAME

TURBO

MTS

V-CHIP

0

No Turbo function

No MTS function

No V-CHIP function

0

Turbo function exists

MTS function exists

V-CHIP function exists

REMARK

1 for army

NT Only

REMARK


4. Troubleshooting

4-1 No Power

No Power

Abnormal Check

Fuse.

Check and Replace

D801S ~ D804S

OFF

Check LED when AC code is plugged.

Normal

ON

Check IC802.

Abnormal

Check/Replace

IC802, R812, D856.

Check

IC801S Pin 1

Oscillation.

Abnormal

Abnormal (0 ~ 15V) Check

IC801S Pin 3 B+.

Check/Replace

D806, Q401, Q801,

D802, D814*

Normal (15~20V)

Abnormal (0V) Check IC801S*

Pin 4 Voltage

Normal (0.5 ~ 3V)

Check/Replace

PC802

Check/Replace

DZ802, D806

Troubleshooting


Troubleshooting

4-2 No Sound


Troubleshooting

4-3 Horizontal Line Appears

Normal (24V)

Single Horizontal Line

Check

24V-C Voltage.

Abnormal

Abnormal

Check

Waveform of IC201S

Pins 22,24.

Check Whether a horizontal line appears in

the service mode..

O.K

Normal

NG

Check/Replace

IC201S.

Check/Replace

IC301.

Check

FBT Pin 2 (24V)

Oscillation.

Normal

Check R409

Open.

Open

Check/Replace

R409.

NG

Check/Replace

FBT.


Troubleshooting

4-4 No Signal

No Signal

Abnormal

Check each tuner terminal voltage.

Normal

Check voltage line.

Check IC201S Pin 41 waveform level.

Abnormal

Normal (2Vp-p)

Check

IC201 Pin 43 waveform level.

Normal (1Vp-p)

Check

IC201S Pins 19,20, 21 waveform level.

Replace IC201S.

Normal (3~5Vp-p)

Check CRT PCB (180V) and heater Voltages.

Abnormal

Check tuner SCL,SDA waveform.

Normal

Check

Micom IC901.

Normal

Check tuner IF terminal waveform.

Abnormal

Check

IC201S Pins 7,8 waveform.

Normal

Replace tuner.

Abnormal

Check whether AGC and

AFTadjustment are normal in the service mode.

Normal

Abnormal

Readjust AGC and AFT.

Check

IC201S Pin 47 waveform level.

Normal (1Vp-p)

Normal (2Vp-p)

Check IC201S

Pin 37 waveform level.


5. Exploded Views & Parts List

5-1 CT2088BL6X/XAP

Exploded Views & Parts List

No

1-7

1-8

1-9

1-10

1-11

1-12

1-13

1-14

1

1-1

1-2

1-3

1-4

1-5

1-6

2

2-1

2-2

2-3

3

3-1

3-2

4

Code No

AA91-00283B

AA64-00704B

AA64-00703D

AA61-60003J

AA64-00705B

AA64-70123B

AA63-00204B

AA63-00205B

AA63-00226B

AA63-00202C

AA61-40113A

AA65-30105A

AA64-00702B

6003-001026

3001-001088

6003-001026

AA03-10029Z

AA65-30107A

AA60-10050R

3704-001105

AA64-00701C

6003-001026

AA42-10001V

AA39-10006X

Samsung Electronics

Description

ASSY CABINET FRONT

WINDOW REMOCON

KNOB POWER

SPRING-CS

INDICATOR LED

BADGE-BRAND

GRILLE-WOOFER,L

GRILLE-WOOFER,R

COVER-TOP,LATIN

COVER-CONTROL

STOPPER-PCB

CLAMP-WIRE

KNOB CONTROL

SCREW-TAPTITE

SPEAKER

SCREW-TAPTITE

CRT-COLOR

CLAMP-D,COIL

SCREW-ASSY

SOCKET-CRT

CABINET BACK

SCREW-TAPTITE

ANT-ROD

POWER-CORD

Specification

;-,20S4,(SPK)SV704 EPG

;-,20S4,-,PC,V0,VIOLET,-”

;-,20S4,T/S NO-SILK,ABS,HB,G36

;-,SUS304,0.5,OD6,H12,N7,-,-,-

;-,20S4,-,ACRYL,-,CLR,-

;AL,R2000,SILVER,L=50,SAMSUNG

;-,20S4,-,SECC,T0.5,SV704

;-,20S4,-,SECC,T0.5,SV704

;-,20S4,T/SOUND,ABS,LG TR

;-,20S4,GD906P EPG NT,HIPS,

;501H,HIPS,NTR,HB,-,-

;NYLON 66,V2,NTR,15MM,ALL MODE

;-,20S4,-,ABS,HB,G3676

;RH,+,B,M4,L15,ZPC(BLK),SWR

;5W,8ohm,90dB,250Hz+-50Hz


;-,A48KRD82X(HB),+380mG,20,90d

;NYLON 66,V2,NTR,-,20~22 INC

;WC,HH,+,M5,L31.5,SWRCH18A,ZPC

;11P,20PI,26.5PI,NI,-

;-,20S4,-,HIPS,HB,BLK,-,-


;-,3S,620mm,BRN,UL/CSA

;-,KKP419C,KLCE-2F,2.286MT,3P,

Q’ty

1

6

1

4

1

1

4

1

1

2

2

1

12

1

1

1

1

1

1

1

1

1

1

1

Remark

5-1

MEMO


Electrical Parts List

6. Electrical Parts List

6-1 CT1488BL6X/XAP (CT1488BL6X/XAP and CT2088BL6X/XAP Dissimilar parts)

Loc. No.

Code No. Description ; Specification Remark

ASSY PCB MAIN(OPT)

* AA94-01968CASSY PCB MAIN(OPT);CT-14S4,K15A,KOREA,-

R412

R413

R518

R518A

R606

R607

RM01

RM02

RS604

RS605

R226

R303

R304

R305

R306

R307

R308

R309

R404

R411

RU10

T444S

V999S

C216

C301

C305

C602

2201-000354 C-CERAMIC,DISC;0.02nF,5%,50V,NP0,TP,5x3,5

2301-000020 C-FILM,PEF;27nF,5%,100V,TP,7.3x4x12.5mm,5

2305-000427 C-FILM,MPEF;47nF,5%,100V,TP,7.5x12.5x3.5,5

2201-000292 C-CERAMIC,DISC;1nF,10%,50V,Y5P,TP,5x3.5,5

CN501

CN604

AA39-20109D LEAD CONNECTOR-ASSY;-,YBNH025-08,S,8P,300,1007#26

3711-002643 CONNECTOR-HEADER;BOX,4P,1R,2.5mm,STRAIGHT,SN

CN705 3711-002641 CONNECTOR-HEADER;BOX,10P,1R,2.54mm,STRAIGHT,Sn

CR401S 2301-001337 C-FILM,MPE-PPF;4.3nF,5%,1.6kV,TP,28.5x16x9mm,20

CR402S 2201-000406 C-CERAMIC,DISC;0.27nF,10%,2kV,Y5P,TP,6.3x5,7.5

CR403S 2306-000171 C-FILM,MPPF;270nF,5%,250V,TP,21.5x12.5mm,7

CS602 2201-000292 C-CERAMIC,DISC;1nF,10%,50V,Y5P,TP,5x3.5,5

JAW03 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm

JAW04 3812-000219 WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING),1/0.6mm

LC801S AA27-20003U COIL-DEGAUSSING;-,14,16.4ohm,75T,890mm,D

LR401S AA27-30003R COIL-LINEARLITY;-,220uH,YL10x10,0.35mm,23x13mm

R204 2001-000995 R-CARBON;820OHM,5%,1/8W,AA,TP,1.8X3.2MM

R205

R206

R214

2001-000995

2001-000995

2001-000290

R-CARBON;820OHM,5%,1/8W,AA,TP,1.8X3.2MM


R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3.2MM

2001-000397 R-CARBON;180KOHM,5%,1/8W,AA,TP,1.8X3.2MM


2003-001036 R-METAL OXIDE(S);3.3ohm,5%,2W,AF,TP,3.9x10mm


2001-001000

2004-001377

2001-000613

2001-000890

2001-000780

AA26-30005S

3704-001112




2003-000649 R-METAL OXIDE(S);330ohm,5%,1W,AF,TP,3.3x9mm

2001-000020 R-CARBON(S);22OHM,5%,1/2W,AA,TP,2.4X6.4MM

R-METAL(S);120Kohm,1%,1/2W,AA,TP,2.4x6.4m

2004-001377 R-METAL(S);120Kohm,1%,1/2W,AA,TP,2.4x6.4m

2001-001037 R-CARBON(S);0.39OHM,5%,1/2W,AA,TP,2.4X6.4MM

2008-000266 R-FUSIBLE(S);1ohm,5%,2W,AF,TP,3.9x10mm

2008-001015 R-FUSIBLE(S);1.5ohm,5%,2W,AF,TP,3.9x10mm

R-CARBON;3.9KOHM,5%,1/8W,AA,TP,1.8X3.2MM

2001-000890 R-CARBON;6.8KOHM,5%,1/8W,AA,TP,1.8X3.2MM

2002-001006 R-COMPOSITION;4.7Kohm,5%,1/2W,AA,TP,3.7x9mm

2002-001006 R-COMPOSITION;4.7Kohm,5%,1/2W,AA,TP,3.7x9mm

2001-000613 R-CARBON;3.9KOHM,5%,1/8W,AA,TP,1.8X3.2MM

R-CARBON;6.8KOHM,5%,1/8W,AA,TP,1.8X3.2MM


TRANS-FLYBACK;-,FSV-14A004(S),14,125V

SOCKET-CRT;8P,12PI,22.5PI,NI,-

Loc. No.


LED

PA+CF

AA64-00755B INDICATOR LED;-,14S4,-,ACRYL,-,CLR,-

AA60-10002A SCREW-TAPPING;RH,+,M4,L12,ZPC(YEL),-,OD14

SPRING AA61-60003J SPRING-CS;-,SUS304,0.5,OD6,H12,N7,-,-,-

WRMC AA64-00754B WINDOW REMOCON;-,14S4,-,PC,V0,VIOLET,-

CRT

DY

MGNT

LEAD

PCBF

ASSY-CRT

* AA94-50015E ASSY-CRT;A34KQV42X(B),+380mG,14,BARE,C

AA03-10001Z CRT-COLOR;-,A34KQV42X(B),+380MG,14,90DE

AA27-50004X DEFLECTION-YOKE;

AA27-00001A MAGNET-CONVERGENCE;-,JH225-06A,22.5MM

ASSY-PCB,A/V FRONT

* AA95-00591A ASSY-PCB,A/V FRONT;-,CT1488BL6,K15A,-,-,-

AA39-20067A LEAD CONNECTOR-ASSY;-,YBNH025-10,67096-010,10P,300

AA41-00250A PCB-FRONT A/V;K15A,1L,FR-1,245x245x1.6T,24A,MC-H/V-

C,51x27

ASSY SPEAKER

* AA96-00321A ASSY SPEAKER;-,8ohm,6W,001034/00320A,350/550

AHDRS AA91-00320A ASSY HOLDER SPK;-,-,PIEZO ASSY,-,SILVER CAP,CT-14S4

LEADC AA39-00105A LEAD CONNECTOR-ASSY;-,-,-,-,-,-,-,-,-,YSH250-

SPK

04,REC,35155-0200,4P,350/550/100mm,1007#22

3001-001034 SPEAKER;6W,8ohm,90dB,140Hz

ASSY CABINET FRONT

* AA91-00317A ASSY CABINET FRONT;-,14S4,(SPK)SV704 EPG B2,HB,GRAY

* AA90-00268A ASSY CABINET;14S4,CT1488BL6X/XAP

BACK

BADGE

CB+CF

CMPD

AA64-00751B

AA64-70127F

6002-000514

AA65-30106A

CABINET BACK;-,14S4,-,HIPS,HB,BLK,-,-

BADGE-BRAND;AL,SAMSUNG,SILVER,L40,R800,NEW

SCREW-TAPPING;RH,+,2,M4,L15,ZPC(BLK),SWRCH18

CLAMP-D,COIL;NYLON 66,V2,NTR,-,14 INCH,-

CRT+CF AA60-10050Q SCREW-ASSY;WC,HH,+,M5,L26.5,SWRCH18A,ZPC(

CVR

CVRT

FRONT

AA63-00215B COVER-CONTROL,A;-,14S4,GD906P EPG NT,HIPS,HB,GRAY,-

AA63-00227B COVER-TOP,LATIN;-,14S4,DG703P,ABS,LG TR558,CLR,-,-

AA64-00750B CABINET FRONT;-,14S4,SV704P EPG

BIO2000,HIPS,HB,GRAY,-,-

AA63-00218B GRILLE-WOOFER,L;-,14S4,SV704G,SECC,T0.5,-,GRILLE

GRILLE

ID+CF

AA63-00219B GRILLE-WOOFER,R;-,14S4,SV704G,SECC,T0.5,-,-

6003-001026 SCREW-TAPTITE;RH,+,B,M4,L15,ZPC(BLK),SWRCH18

KNOBC AA64-00752B KNOB CONTROL;-,14S4,-,ABS,HB,G3676

KNOBP AA64-00753B KNOB POWER;-,14S4,NT NO-SILK,ABS,HB,G3676



6-2 CT2088BL6X/XAP

C313

C401

C405

C406

C407

C408

C409

C410

C411

C412

C302

C303

C304

C305

C306

C308

C309

C310

C311

C312

C413

C444

C445

C501

C502

C503

C505

C601

C602

C603

C227

C229

C230

C231

C232

C234

C235

C236

C237

C301

C213

C214

C215

C218

C219

C220

C221

C222

C225

C226

C202

C203

C204

C205

C206

C207

C209

C210

C211

C212

C101

C102

C104

C108

C110

C151

C153

C201

Loc. No.


ASSY PCB MAIN(OPT)

* AA94-01968BASSY PCB MAIN(OPT);CT20S4Z6X/XAP,K15A-1,

2202-000127 C-CERAMIC,MLC-AXIAL;10nF,+80-20%,25V,Y5V

2401-000660 C-AL;2.2uF,20%,50V,GP,TP,5x11,5


2401-000480 C-AL;10uF,20%,50V,GP,TP,5x11,5

2401-002594 C-AL;220uF,20%,16V,GP,TP,8x11.5,5



2201-000292 C-CERAMIC,DISC;1nF,10%,50V,Y5P,TP,5x3.5,

2401-001333 C-AL;470nF,20%,50V,GP,TP,5x11,5

2401-002144 C-AL;47uF,20%,16V,GP,TP,5x11,5

2301-000188 C-FILM,PEF;1nF,5%,100V,TP,10.5x12.5x6.5,

2401-001333 C-AL;470nF,20%,50V,GP,TP,5x11,5

2305-001011 C-FILM,MPEF;22nF,5%,100V,TP,3.5x12.5x7.5

2401-001333 C-AL;470nF,20%,50V,GP,TP,5x11,5

2202-002037 C-CERAMIC,MLC-AXIAL;100nF,80-20%,50V,Y5V



2201-000982 C-CERAMIC,DISC;10nF,+80-20%,50V,Y5V,TP,4

2201-000193 C-CERAMIC,DISC;0.01nF,0.25pF,50V,NP0,TP,

2401-000660 C-AL;2.2uF,20%,50V,GP,TP,5x11,5

2401-001840 C-AL;100uF,20%,16V,GP,TP,6.3x11,5

2301-000395 C-FILM,PEF;18nF,5%,50V,TP,6.5x12.5x3.5mm

2401-000603 C-AL;1uF,20%,50V,GP,TP,5x11,5

2401-000480 C-AL;10uF,20%,50V,GP,TP,5x11,5

2401-002462 C-AL;33uF,20%,16V,GP,TP,5x11,5

2305-000665 C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0m

2401-000480 C-AL;10uF,20%,50V,GP,TP,5x11,5

2401-000603 C-AL;1uF,20%,50V,GP,TP,5x11,5




2401-002144 C-AL;47uF,20%,16V,GP,TP,5x11,5

2401-002144 C-AL;47uF,20%,16V,GP,TP,5x11,5

2301-000232 C-FILM,PEF;3.3nF,5%,50V,TP,8.1x4.5x13mm,

2202-000279 C-CERAMIC,MLC-AXIAL;47pF,5%,50V,SL,TP,3.


2202-000791 C-CERAMIC,MLC-AXIAL;150pF,10%,50V,Y5P,TP


2201-000556 C-CERAMIC,DISC;0.47nF,10%,500V,Y5P,TP,5.


2401-000553 C-AL;1uF,10%,50V,HR,TP,5x11mm,5mm

2305-000149 C-FILM,MPEF;100nF,5%,100V,TP,12x12.5x6.5

2401-002458 C-AL;1000uF,20%,35V,GP,TP,16x25,7.5

2301-000310 C-FILM,PEF;68nF,5%,50V,TP,8.0X8.5X4.0X5,

2401-000365 C-AL;100uF,20%,50V,WT,TP,10x12.5mm,5

2401-000480 C-AL;10uF,20%,50V,GP,TP,5x11,5

2401-001333 C-AL;470nF,20%,50V,GP,TP,5x11,5

2401-000553 C-AL;1uF,10%,50V,HR,TP,5x11mm,5mm

2305-000470 C-FILM,MPEF;68nF,5%,100V,TP,-,5mm

2301-000224 C-FILM,PEF;22nF,5%,50V,TP,7.4x3.9x13mm,5

2305-000704 C-FILM,MPEF;100nF,5%,250V,TP,16.5x10.3x5


2401-001429 C-AL;470uF,20%,50V,GP,TP,13x20,5


2401-001998 C-AL;1000uF,20%,25V,GP,TP,10x20,5mm

2301-000224 C-FILM,PEF;22nF,5%,50V,TP,7.4x3.9x13mm,5


2401-000927 C-AL;22UF,20%,250V,GP,TP,13X20mm,5mm

2401-002268 C-AL;2.2uF,20%,250V,LZ,TP,8X11,5

2201-000441 C-CERAMIC,DISC;3.3nF,10%,500V,Y5P,TP,10x

2201-000441 C-CERAMIC,DISC;3.3nF,10%,500V,Y5P,TP,10x




2201-002063 C-CERAMIC,DISC;10nF,+80-20%,3KV,Y5V,TP,1

2401-001998 C-AL;1000uF,20%,25V,GP,TP,10x20,5mm

2301-000383 C-FILM,PEF;10nF,5%,50V,TP,6x7x3.2mm,5mm

2401-000603 C-AL;1uF,20%,50V,GP,TP,5x11,5

Loc. No.


C905

C907

C908

C909

C910

C911

C912

C915

CMPF

CMPF

C820

C821

C822

C823

C851

C852

C901

C902

C903

C904

C803

C805

C806

C807

C808

C810

C811

C812

C816

C817

C604

C611

C612

C701

C705

C801

C802

2401-000603 C-AL;1uF,20%,50V,GP,TP,5x11,5




2202-000183 C-CERAMIC,MLC-AXIAL;2.2NF,20%,16V,Y5R,TP

2401-003025 C-AL;330uF,20%,400V,GP,ST,30x40,10

2201-000119 C-CERAMIC,DISC;100nF,+80-20%,50V,Y5V,TP,

2301-001342 C-FILM,PPF;1.5nF,5%,800V,TP,15x6.5x11.5m

2201-000991 C-CERAMIC,DISC;0.56nF,10%,2kV,Y5P,TP,7.5

2401-000262 C-AL;100uF,20%,160V,HR,TP,16x25,7.5




2401-000302 C-AL;100uF,20%,25V,GP,TP,6.3x11,5

2401-001840 C-AL;100uF,20%,16V,GP,TP,6.3x11,5

2401-000480 C-AL;10uF,20%,50V,GP,TP,5x11,5

2401-001840 C-AL;100uF,20%,16V,GP,TP,6.3x11,5

2401-000703 C-AL;2200uF,20%,25V,GP,-,12.5x25mm,

2401-001486 C-AL;47uF,20%,160V,HR,TP,13x20mm,5m

2301-000192 C-FILM,PEF;1nF,5%,50V,TP,5.3x10mm,5mm

2201-000370 C-CERAMIC,DISC;0.22nF,10%,50V,Y5P,TP,4x3

2401-001192 C-AL;33uF,20%,50V,GP,TP,6.3x11,5

2301-000235 C-FILM,PEF;3.9nF,5%,50V,TP,6.5x3.0x5.5mm

2401-002144 C-AL;47uF,20%,16V,GP,TP,5x11,5

2202-000796 C-CERAMIC,MLC-AXIAL;1NF,10%,50V,Y5P,TP,3

2401-000480 C-AL;10uF,20%,50V,GP,TP,5x11,5

2202-000796 C-CERAMIC,MLC-AXIAL;1NF,10%,50V,Y5P,TP,3

2401-001333 C-AL;470nF,20%,50V,GP,TP,5x11,5

2401-000027 C-AL;4.7uF,20%,50V,GP,TP,5x11,5

2201-000193 C-CERAMIC,DISC;0.01nF,0.25pF,50V,NP0,TP,

2201-000573 C-CERAMIC,DISC;0.047nF,5%,50V,NP0,TP,5x3

2301-000445 C-FILM,PEF;4.7nF,5%,50V,TP,5.5x7x3mm,5mm

2401-000480 C-AL;10uF,20%,50V,GP,TP,5x11,5



AA65-30009A CLAMP-FBT;ABS,V0,BLK,-,-,-

AA65-30109A CLAMP-FBT;NYLON-66,V2,BLK,-,-,-

D402

D403

D404

D405

D407

D601

D204

D205

D206

D207

D208

D210

D299

D301

D302

D401

CMPW

CN501

CN604

CN704

AA65-30104C CLAMP-WIRE;NYLON 66,V2,NTR,W1 Z4,ALL MOD

AA39-20109A LEAD CONNECTOR-ASSY;-,YBNH025-08,S,8P,40

3711-000963

3711-003641

CONNECTOR-HEADER;BOX,4P,1R,2.5mm,STRAIGH

CONNECTOR-HEADER;BOX,12P,1R,2.5mm,STRAIG

CR401S 2306-000255 C-FILM,MPPF;7.4nF,3%,1.6KV,TP,28.5x18.5x

CR402S 2201-000639 C-CERAMIC,DISC;0.68nF,10%,2kV,Y5P,TP,9x5

CR403S 2306-000193 C-FILM,MPPF;360nF,5%,200V,TP,21x18.5x13,

CS601

CS602

CS603

2401-000603

2301-000383

2202-000796

C-AL;1uF,20%,50V,GP,TP,5x11,5

C-FILM,PEF;10nF,5%,50V,TP,6x7x3.2mm,5mm

C-CERAMIC,MLC-AXIAL;1NF,10%,50V,Y5P,TP,3

CS608

CS609

2202-000222 C-CERAMIC,MLC-AXIAL;3.3nF,20%,16V,Y5P,TP

2202-000222 C-CERAMIC,MLC-AXIAL;3.3nF,20%,16V,Y5P,TP

CU02 2305-000665 C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0m

CY801S 2201-000446 C-CERAMIC,DISC;3.3nF,20%,400V,Y5U,TP,15x

D101 0403-000700 DIODE-ZENER;TZP33A,33V,31-35V,1W,DO-41,T

D102

D103

D201

D202

D203

0403-000508

0402-000132

0403-000663

0401-000005

0401-000005

DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500

DIODE-RECTIFIER;1N4004,400V,1A,DO-41,TP

DIODE-ZENER;MTZ3.3B,3.3V,3.32-3.53V,500m

DIODE-SWITCHING;1N4148,100V,200MA,DO-35,


0401-000005

0403-000355

0401-000005

0401-000005

0402-000132

0401-000005


DIODE-ZENER;UZ5.1BSB,5.1V,4.97-5.18V,500



DIODE-RECTIFIER;1N4004,400V,1A,DO-41,TP

0403-000563 DIODE-ZENER;MTZ9.1B,9.1V,8.57-9.01V,500m

0403-000654 DIODE-ZENER;MTZ12B,12V,11.44-12.03V,500m

0402-001105 DIODE-RECTIFIER;ERB43-04SV1,400V,1.0A,-,


0402-000132 DIODE-RECTIFIER;1N4004,400V,1A,DO-41,TP

0402-000132 DIODE-RECTIFIER;1N4004,400V,1A,DO-41,TP








Loc. No.


DZ209

DZ601

DZ602

DZ603

DZ610

DZ802

DZ806

DZ808

DZ901

DZ902

DS602

DS603

DZ201

DZ202

DZ203

DZ204

DZ205

DZ206

DZ207

DZ208

D814A

D855

D856

D901

D902

D903

D904

D905

D906

D907

D701

D801S

D802

D802S

D803

D803S

D804

D804S

D805

D806


0402-000213 DIODE-RECTIFIER;ERB12-06,600V,1.0A,DO-41

0402-000540 DIODE-RECTIFIER;RU20A,600V,1.5A,-,TP







0401-000005 DIODE-SWITCHING;1N4148,100V,200MA,DO-35,

0402-001351 DIODE-RECTIFIER;YG911S2R,200V,5A,TO-220, H/SINK

0403-000508 DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500









0403-000656 DIODE-ZENER;MTZ15C,15V,14.35-15.09V,500m















0403-000658 DIODE-ZENER;MTZ18A,18V,16.22-17.06V,500m


0403-000699 DIODE-ZENER;TZP27B,27V,27-30.8V,1W,DO-41



L802

L803

L804

L805

L810

L811

L901

L402

L501

L502

L503

L602

L204

L205

L206

L208

L301

L102

L152

L201

L202

L203

IC801S

IC802

IC901

IC902

JA701

DZ903

DZ904

F801A

F801B

0403-000355

0403-000508

3602-000114

3602-000114

DIODE-ZENER;UZ5.1BSB,5.1V,4.97-5.18V,500

DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500

FUSE-HOLDER;-,-,30mohm

FUSE-HOLDER;-,-,30mohm

FA801S 3601-001086 FUSE-AXIAL LEAD;125V,5A,FAST-ACTING,GLAS

FP801S 3601-001012 FUSE;250V,4A,SLOW-BLOW,GLASS,5.2x20

GT101A AA39-20010D LEAD CONNECTOR-ASSY;-,YFH800-01,S,1P,400

IC201S

IC301

IC601

1204-001259

1204-000475

1201-001308

IC-VIDEO SYSTEM;TA1282N,DIP,56P,600MIL,P

IC-VIDEO SYSTEM;KA2131,SIP,10P,-,PLASTIC H/SINK

IC-POWER AMP;7266,ZIP,15P,-,DUAL,26dB,PL H/SINK

1203-001932

1203-001532

1103-001107

3722-001453

IC-PWM CONTROLLER;5Q0765,TO-220F,5P,185M H/SINK

IC-POSI.FIXED REG.;7631,SIP,10P,-,PLASTI

AA13-00081A IC-MCU;Z9036512PSC-R4474,SZM-370TH,ST

IC-EEPROM;24C021C,256x8Bit,DIP,8P,300MIL

JACK-RCA;3P,3.4mm,NI,BLK,-

2701-000178 INDUCTOR-AXIAL;33uH,10%,3x7mm

2701-000202 INDUCTOR-AXIAL;560nH,10%,2.5x3.4mm

AA26-10004K TRANS-IF;-,7MG,SIF,11.5uH,7mm,100pF,4.8

2701-000207 INDUCTOR-AXIAL;56uH,5%,2.5x3.4mm


2701-000207

AA26-10004C TRANS-IF;-,7MG,VIF,0.37uH,7mm,27pF,52.3

2701-000111

2701-000114

2701-000116

2901-000297

2701-000197

INDUCTOR-AXIAL;56uH,5%,2.5x3.4mm





2701-000184 INDUCTOR-AXIAL;4.7uH,10%,2.5x3.4mm




3301-001223 CORE-FERRITE BEAD;AB,-,3.5X5X0.8MM,-,TP,

2901-000297 FILTER-EMI ON BOARD;-,3A,-,-,3.5x5,TP,-

3301-001223 CORE-FERRITE BEAD;AB,-,3.5X5X0.8MM,-,TP,

2901-000297 FILTER-EMI ON BOARD;-,3A,-,-,3.5x5,TP,-


FILTER-EMI ON BOARD;-,3A,-,-,3.5x5,TP,-

INDUCTOR-AXIAL;5.6uH,10%,2.5x3.4mm

Loc. No.


R251

R252

R253

R257

R301

R302

R303

R231

R233

R234

R235

R236

R237

R239

R240

R241

R242

R215

R218

R219

R222

R223

R226

R227

R228

R229

R230

R205

R206

R207

R208

R209

R210

R211

R212

R213

R214

R154

R155

R156

R157

R158

R159

R201

R202

R203

R204

Q903

QU01

R101

R102

R104

R105

R106

R107

R152

R153

Q201

Q202

Q203

Q401

Q402

Q501

Q502

Q503

Q601

Q801

L902

L999

LC801S

LD901

LR401S



AA27-20003X COIL-DEGAUSSING;-,20,14.4ohm,48T,L2170,

AA96-30007A ASSY-LED,GUIDE;-,AA61-50055A,DL-G7GA,GRE

AA27-30001B COIL-LINEARLITY;-,195uH,QIC1010,PI0.4,4.

LX801S AA29-30001D FILTER-LINE NOISE;SQ1913,-,6.0MH,0.8A,-

NT801S 1404-001045 THERMISTOR-NTC;4.7OHM,15%,2900K,35.0MW,T

P801S

PC801S

Q151

1404-001048

0604-001038

0501-000436

THERMISTOR-PTC;7ohm,30%,200/220V,270Vac,

PHOTO-COUPLER;TR,130-260%,200mW,DIP-4,ST

TR-SMALL SIGNAL;KTC3197,NPN,625mW,TO-92,

0501-002183

0501-002183

0501-002183

0502-001115

0501-000369




TR-POWER;KSC5386,NPN,50W,TO-3PF,ST,8-

TR-SMALL SIGNAL;KSC2331-Y,NPN,1W,TO-92L,

0501-002014 TR-SMALL SIGNAL;KSC2330-R,NPN,1W,TO-92L,



0501-002183 TR-SMALL SIGNAL;KTC9014,NPN,625mW,TO-92,

1203-001217 IC-POSI.ADJUST REG.;431,TO-92,3P,4.58MIL

0501-002183

0504-000123

2001-001155

2001-001000

2003-000592

2003-000592 R-METAL OXIDE(S);22ohm,5%,2W,AF,TP,4x12m



2001-000221 R-CARBON;1.2KOHM,5%,1/8W,AA,TP,1.8X3.2M

2001-000734

2001-000780 R-CARBON;470OHM,5%,1/8W,AA,TP,1.8X3.2MM




2001-000007





2001-000221

2001-000221

2001-000221

2001-001111

2001-000515

2001-000515

2001-000003

2001-000908


TR-DIGITAL;KSR1010,NPN,300mW,10K,TO-92,T

R-CARBON(S);5.6KOHM,5%,1/2W,AA,TP,2.4X6.


R-METAL OXIDE(S);22ohm,5%,2W,AF,TP,4x12m

R-CARBON;4.7KOHM,5%,1/8W,AA,TP,1.8X3.2M





R-CARBON(S);240OHM,5%,1/2W,AA,TP,2.4X6.4











2001-000773 R-CARBON;470KOHM,5%,1/8W,AA,TP,1.8X3.2M










2004-000195 R-METAL;100Kohm,1%,1/8W,AA,TP,1.8x3.2m










2008-000252 R-FUSIBLE(S);0.47ohm,10%,1/2W,AF,TP,2.5x


R-CARBON;330ohm,5%,1/8W,AA,TP,1.8x3.2mm




Loc. No.


R854

R901

R902

R903

R904

R905

R906

R817

R819

R819A

R820

R821

R823

R824

R825

R852

R853

R802

R803

R807

R808

R809

R810A

R811

R812

R814

R816

R602

R603

R604

R606

R607

R610

R611

R701

R702

R801

R510

R511

R512

R513

R514

R515

R517

R518

R599

R601

R444

R501

R502

R503

R504

R505

R506

R507

R508

R509

R405

R406

R407

R409

R410

R411

R412

R415

R416

R417

R304

R305

R306

R307

R308

R309

R401

R402

R403

R404

2003-000436 R-METAL OXIDE(S);1.5ohm,5%,1W,AF,TP,3.3x





2003-001043 R-METAL OXIDE(S);510ohm,5%,1W,AF,TP,2.5x



2001-001114 R-CARBON(S);270OHM,5%,1/2W,AA,TP,2.4X6.4

2001-001136 R-CARBON(S);36OHM,5%,1/2W,AA,TP,2.4X6.4M

2003-000540 R-METAL OXIDE(S);1Kohm,5%,2W,AF,TP,4x12m

2008-001107 R-FUSIBLE(S);300ohm,5%,2W,AG,TP,3.9x12mm

2003-002102 R-METAL OXIDE;68Kohm,5%,2W,AF,TP,4x12mm

2008-000253 R-FUSIBLE(S);0.47ohm,5%,1W,AF,TP,3.9x10m

2008-000206 R-FUSIBLE(S);1ohm,5%,1/2W,AF,TP,2.5x6.5m

2004-001373 R-METAL(S);100Kohm,1%,1/2W,AA,TP,2.4x6.4


2003-000784 R-METAL OXIDE(S);7.5Kohm,5%,2W,AF,TP,4x1



2001-001099 R-CARBON(S);2.7KOHM,5%,1/2W,AA,TP,2.4X6.




2003-002170 R-METAL OXIDE(S);15Kohm,5%,2W,AG,TP,3.9x











2002-001006 R-COMPOSITION;4.7Kohm,5%,1/2W,AA,TP,3.7x


2008-001015 R-FUSIBLE(S);1.5ohm,5%,2W,AF,TP,3.9x10mm

2008-001053 R-FUSIBLE;22ohm,5%,1/2W,AF,TP,2.5x6.5mm











2001-001150 R-CARBON(S);470KOHM,5%,1/2W,AA,TP,2.4X6.

2003-000994 R-METAL OXIDE(S);33Kohm,5%,2W,AF,TP,3.9x




2008-000205 R-FUSIBLE(S);10ohm,5%,1/2W,AF,TP,2.5x6.5

2008-000261 R-FUSIBLE(S);150ohm,5%,1W,AF,TP,3.9x10mm

2001-001170 R-CARBON(S);6.8OHM,5%,1/2W,AA,TP,2.4X6.4

2008-000252 R-FUSIBLE(S);0.47ohm,10%,1/2W,AF,TP,2.5x



2001-001170 R-CARBON(S);6.8OHM,5%,1/2W,AA,TP,2.4X6.4

2008-000284 R-FUSIBLE(S);0.1OHM,10%,2W,AF,TP,3.9X10M

2008-000284 R-FUSIBLE(S);0.1OHM,10%,2W,AF,TP,3.9X10M




2004-001983 R-METAL(S);2.49Kohm,1%,1/2W,AA,TP,2.4x6.

2001-001108 R-CARBON(S);22KOHM,5%,1/2W,AA,TP,2.4X6.4

2004-001371 R-METAL(S);1.5Kohm,1%,1/2W,AA,TP,2.4x6.4

2004-001390 R-METAL(S);1Kohm,2%,1/2W,AA,TP,2.4x6.4mm








Loc. No.


R919

R920

R921

R922

R923

R924

R925

R926

R927

R929

R907

R909

R910

R911

R913

R914

R915

R916

R917

R918





















R930

R931

R932

R933

R936

R937

R938

R939

R940

R941











R951

R952

R988

RH01

RH02






RM901 AA59-60001U MODULE-REMOCON;-,ORC-50VF/SR-12V,38KHz,9

RR401S 2004-001390 R-METAL(S);1Kohm,2%,1/2W,AA,TP,2.4x6.4mm

RS601

RS602

RS604

2001-000734

2001-000734

2001-000258




SF101S

SW901

SW902

SW903

SW904

SW905

SW906

T401

T444S

T801S

RS605

RS606

RS607

RS613

RS614






RU02

RU06

RU07

RU10

2001-000780

2001-000397

2001-001062

2001-000924


R-CARBON;180KOHM,5%,1/8W,AA,TP,1.8X3.2M

R-CARBON(S);10MOHM,5%,1/2W,AA,TP,2.4X6.4


RY801S 2002-001013 R-COMPOSITION;4.7Mohm,5%,1/2W,AA,TP,3.7x

2904-000304

3404-000244

3404-000244

3404-000244

3404-000244

FILTER-SAW AV;45.75MHz,SIP5K,ST,14.7dB,M

SWITCH-TACT;15V,20mA,90-170gf,7.5x7mm,SP




3404-000244 SWITCH-TACT;15V,20mA,90-170gf,7.5x7mm,SP

3404-000295 SWITCH-TACT;12VDC,50mA,160gf,8.4X22.7,SP

AA26-50001B TRANS-HORIZ.DRIVE;-,7.1mH,102uH,10-20uH,

AA26-30001Y TRANS-FLYBACK;-,FSV-20A001,20,125V

AA26-00043A TRANS SWITCHING;-,-,-,AC90~260V,125/12.5

TU01S

V999S

AA40-10006U TUNER-F/S;TECC1070PG31A(S),NTSC,TR,181CH

3704-001105 SOCKET-CRT;11P,20PI,26.5PI,NI,-

VX801S 1405-000152 VARISTOR;560V,2500A,14x8.5mm,TP

X201 2801-003725 CRYSTAL-UNIT;3.579545MHz,20ppm,28-AAM,16

X202 2802-000172 RESONATOR-CERAMIC;503.5KHZ,0.5%,BK,7.0X3

X901

Z201

Z601

2801-003224

2903-001022

2903-000135

CRYSTAL-UNIT;32.768KHZ,20PPM,28-AAY,12.5

FILTER-CERAMIC;BR,4.5MHz,-,-,-,TP,-

FILTER-CERAMIC;BP,4.5MHz,120KHz,6dB,-,TP

ASPK

ASSY CABINET FRONT

* AA91-00283B ASSY CABINET FRONT;-,20S4,(SPK)SV704 EPG

* AA90-00244B ASSY CABINET;20S4,CT2088BL6X/XAP

AA96-00287A ASSY SPEAKER;-,8ohm,15W,001115/001088,AA



Loc. No.


BACK

BADGE

C/B

CB+CF

CMPC

AA64-00701C CABINET BACK;-,20S4,-,HIPS,HB,BLK,-,-

AA64-70123B BADGE-BRAND;AL,R2000,SILVER,L=50,SAMSUNG

AA63-60001X SPACER-FELT;FELT,T0.5,BLK,330X15,-,-

6003-001026 SCREW-TAPTITE;RH,+,B,M4,L15,ZPC(BLK),SWR

AA65-30008A CLAMP-CORD;PE,HB,BLK,-,-,-

CMPD

CMPW

AA65-30107A CLAMP-D,COIL;NYLON 66,V2,NTR,-,20~22 INC

AA65-30105A CLAMP-WIRE;NYLON 66,V2,NTR,15MM,ALL MODE

CRT+CF AA60-10050R SCREW-ASSY;WC,HH,+,M5,L31.5,SWRCH18A,ZPC

CVRC AA63-00202C COVER-CONTROL;-,20S4,GD906P EPG NT,HIPS,

CVRT AA63-00226B COVER-TOP,LATIN;-,20S4,T/SOUND,ABS,LG TR

FRONT AA64-00700D CABINET FRONT;-,20S4,SV704P PGB2000,HIPS

GRILLEW AA63-00204B GRILLE-WOOFER,L;-,20S4,-,SECC,T0.5,SV704

GRILLEW AA63-00205B GRILLE-WOOFER,R;-,20S4,-,SECC,T0.5,SV704

INLAY AA64-60385G INLAY BACK;3E,K15A-1 3PIN S/T,PS SHEET,T

KC+CF 6003-001026 SCREW-TAPTITE;RH,+,B,M4,L15,ZPC(BLK),SWR

KNOBC

KNOBP

LEAD

LED

PA+CF

AA64-00702B KNOB CONTROL;-,20S4,-,ABS,HB,G3676

AA64-00703D KNOB POWER;-,20S4,T/S NO-SILK,ABS,HB,G36

AA39-00091A LEAD CONNECTOR-ASSY;-,-,-,-,-,-,-,-,-,52

AA64-00705B INDICATOR LED;-,20S4,-,ACRYL,-,CLR,-

6003-001024 SCREW-TAPTITE;RWH,+,B,M4,L12,ZPC(YEL),SW

POWER AA61-60003J SPRING-CS;-,SUS304,0.5,OD6,H12,N7,-,-,-

SPA AA63-60002W SPACER-FELT;FELT,T0.5,BLK,30X10,-,-

SPA

SPK

SPK

AA63-60001P SPACER-FELT;FELT,T1.0,BLK,230X15,-,-

3001-001088

3001-001115

SPEAKER;5W,8ohm,90dB,250Hz+-50Hz

SPEAKER;15W,8ohm,93dB,110

SPK+CF 6003-001026 SCREW-TAPTITE;RH,+,B,M4,L15,ZPC(BLK),SWR

STOPP AA61-40113A STOPPER-PCB;501H,HIPS,NTR,HB,-,-

WRMC AA64-00704B WINDOW REMOCON;-,20S4,-,PC,V0,VIOLET,-

ANT

BATT

IB

IB

IB

PLUG

TRANS

ASSY ACCESSORY

* AA94-02098AASSY ACCESSORY;CT2088BL6X/XAP,K15A,PANAM

AA42-10001V ANT-ROD;-,3S,620mm,BRN,UL/CSA

4301-000120 BATTERY-MN;1.5V,-,AA,14.5x50mm,-

AA68-00790A MANUAL USERS;K15A,W/P100(G),32PAGE,A5,1’

AA68-00791A MANUAL USERS;K15A,W/P100(G),32PAGE,A5,1’

AA68-30004A MANUAL-BOOK;-,W/P120(G),-,SEPA,-,-

3721-000136 PLUG-CONVERSION;2P,4.0mm,N,NI

AA26-90001F TRANS-MATCHING;-,300ohm/75ohm,NTSC,40-89

CRT

DY

MGNT

SPA

ASSY-CRT

* AA94-50019L ASSY-CRT;A48KRD82X(HB),+380MG,20,BARE,

AA03-10029Z CRT-COLOR;-,A48KRD82X(HB),+380mG,20,90d

AA27-50004W DEFLECTION-YOKE;-,DSE-1992LL(1H),20’/A48

AA27-00002A MAGNET-CONVERGENCE;-,JH291-SC-OB,29.1MM

AA63-60028A SPACER-DY;NEOPRENE,-,BLK,V0 W12,-,-

CA09

CA10

CA11

CA12

CA13

CA32

CNA01

CNA02

CNA03

DA01

CA01

CA02

CA03

CA04

CA05

CA06

CA07

CA08

ASSY-PCB,SOUND

* AA95-00437AASSY-PCB,SOUND;-,CT5066BZG,K15A,-,-,TURB

2401-000480 C-AL;10uF,20%,50V,GP,TP,5x11,5

2401-000603 C-AL;1uF,20%,50V,GP,TP,5x11,5

2401-000603 C-AL;1uF,20%,50V,GP,TP,5x11,5

2401-000603 C-AL;1uF,20%,50V,GP,TP,5x11,5

2401-000603 C-AL;1uF,20%,50V,GP,TP,5x11,5





2301-000289 C-FILM,PEF;5.6nF,5%,50V,TP,7x6x3,5

2301-000289 C-FILM,PEF;5.6nF,5%,50V,TP,7x6x3,5

2401-000027 C-AL;4.7uF,20%,50V,GP,TP,5x11,5

2401-000027 C-AL;4.7uF,20%,50V,GP,TP,5x11,5


3711-002702 CONNECTOR-HEADER;NOWALL,4P,1R,2.5mm,ANGL

3711-002703 CONNECTOR-HEADER;NOWALL,5P,1R,2.5mm,ANGL

AA61-10068A BRACKET-PCB;-,M2160,SPTE,T0.3,-,-,-


Loc. No.


ICA02

PCBS

QA01

RA01

RA05

RA06

RA07

RA08

RA18

RA19

1204-001455 IC-VOLUME/TONE CONT.;TDA7449,DIP,20P,300

AA41-00072A PCB-STEREO MODULE;K15A,1L,FR-1,245X245X1

0501-000389 TR-SMALL SIGNAL;KSC815,NPN,400mW,TO-92,T








ASSY-PCB,A/V FRONT

* AA95-00577AASSY-PCB,A/V FRONT;-,CT2088BL6,K15A,-,-,

CE01 2401-000480 C-AL;10uF,20%,50V,GP,TP,5x11,5

CE02 2401-000480 C-AL;10uF,20%,50V,GP,TP,5x11,5

CN705A AA39-20071D LEAD CONNECTOR-ASSY;-,YBNH025-12,67096-0

JE601 3722-000143 JACK-PHONE;1P(VER),3.4mm,AG,BLK,NO

JR01

PCBAV

RE01

RE02

3722-001031

2001-001077

JACK-RCA;3P,3.6MM,#18,AU

AA41-00227A PCB-AV FRONT;K15A-1,1L,FR-1,245x245x1.6T


R-CARBON(S);150OHM,5%,1/2W,AA,TP,2.4X6.4

HDRP

PCORD

ASSY-POWER,CORD

* AA96-20109C ASSY-POWER,CORD;-,CP2/NO(4.0),H/C300,KKP

AA61-20284A HOLDER;-,P-CORD,PP,VO,BLK,KE-002

AA39-10006X POWER-CORD;-,KKP419C,KLCE-2F,2.286MT,3P,

REMOCON

* AA59-00077AREMOCON;-,TM59,SZM370PH,25,L/GRAY,SS,E


MEMO


Block Diagram

7. Block Diagram

TU01

TUNER

TELH9-212A

(TECC107OPG31A)

IC902

EEPROM

KS24C020

IC901

MICOM

SZM370TH

D801~D804

POWER-CORD

CP2-NO(4.0)

IC801S

SAPS CONTROL IC

KA3SO680

SF101

SAW

M1859M

SOUND MODULE PCB

TURBO SOUND

IC601

SOUND AMP

TDA7266S

2- CH

SPEAKER

8ohm

6W

SOUND

IC201S

1 - CHIP

1F/V/C/D

KA2163B(TA1282N)

SWITCHING

TRANS

S:125V,12.5V

125V

12.5V

T801S

PC802

PHOTO

COULPER

R,G,B

VIDEO

EXT IN

VIDEO

EXT IN

AUDIO

IC301

VERTICAL-AMP IC

KA2131

Q401

HORIZONTAL-TR

KSC5386

IC802

MULTI-REGULATOR

KA7631

5V MICOM

9V 1-CHIP

T444S

FBT

FSV20A001(S)

CRT


MEMO


Wiring Diagram

8. Wiring Diagram

K

E

R

S

P

E

A

SOUND

MODULE

PCB

C

R

T

R- OUT

L- OUT

GND

A/V R IN

A/V L IN

TV-SOUND

9V

SCL

SDA2

D.Y

H1

H2

V1

V2

L+

L -

L+

L -

R- OUT

L- OUT

GND

A/V R IN

A/V L IN

TV-SOUND

9V

SCL

SDA2

H1

H2

V1

V2

CN604

M

A

N

I

S

Y

A

S

CN703

R-IN

R-OUT

V-OUT

L - IN

L- OUT

V - IN

GND

AV-L OUT

AV-L IN

R

G

B

9V

GND

180V

GND

HEATER

CN201

R

G

B

9V

GND

180V

GND

HEATER

CN501

P

C

B

C

R

T

R-IN

R-OUT

V-OUT

L - IN

L- OUT

V - IN

GND

AV-L OUT

AV-L IN

A/V

ASSY


MEMO


9. Schematic Diagrams

9-1 MAIN 1/4

Samsung Electronics

TP2

TP4

TP1

TP3

TP5

TP6

TP7

TP11

TP10

TP9

TP8

Schematic Diagrams

TP7 TP1

TP8 TP2

TP9 TP3

TP10 TP4

TP11 TP5

TP6

: Power Line

: Signal Line

9-1

Schematic Diagrams

9-2 MAIN 2/4

9-2

TP12

TP14

TP13

TP15

TP16

TP17

TP18

TP19

TP20

TP21

TP22

TP23

TP18 TP12

TP19 TP13

TP20 TP14

TP21 TP15

TP22 TP16

TP23 TP17

: Power Line

: Signal Line

Samsung Electronics

9-3 MAIN 3/4

Samsung Electronics

TP24

TP25

TP26

TP27

TP37

TP38

TP36

TP28

TP32

TP31

TP33

TP30

TP29

TP36 TP37

TP34

TP35

TP38

TP30

Schematic Diagrams

TP24

TP31 TP25

TP32 TP26

TP33 TP27

TP34 TP28

TP35 TP29

: Power Line

9-3

Schematic Diagrams

9-4 MAIN 4/4

9-4

: Power Line

: Signal Line

Samsung Electronics

Samsung COLOR TELEVISION Specifications

COLOR TELEVISION RECEIVER

Chassis : K15A (H)

Model: CT2088BL6X/XAP

CT1488BL6X/XAP

COLOR TELEVISION RECEIVER CONTENTS

1.

Precautions

2.

Specifications

3.

Alignment and Adjustments

4.

Troubleshooting

5.

Exploded Views and Parts List

6.

Electrical Parts List

7.

Block Diagram

8.

Wiring Diagrams

9.

Schematic Diagrams

ELECTRONICS

© Samsung Electronics Co., Ltd. APR. 2000

Printed in Korea

1. Precautions

1-1 Safety Precautions

1-1 Safety Precautions (Continued)

1-2 Servicing Precautions

1-3 Precautions for Electrostatically Sensitive Devices (ESDs)

2. Specifications

2-1 Specifications

3. Alignment and Adjustments

3-1 Service Mode Adjustments

3-1-1 Service Mode Menus

3-1-2 Entering the Service Mode

3-1-3 Adjustment in Option Mode

3-1-4 Service Mode Adjustments

3-1-5 Service Mode Adjustment Ratings

3-2 Alignment and Adjustment

3-2-1 General Alignment Instructions

3-2-2 Power Supply Check

3-2-3 Focus Adjustment

3-2-4 Fail Safe Circuit Check (FS) (OPTION)

3-2-5 IC902 Replacement

3-2-6 PIF VCO Adjustment

3-2-7 RF-AGC Adjustment

3-2-8 Sub-Contrast Adjustment

3-2-10 Sub-Color Adjustment

3-2-9 Sub-Tint Adjustment

3-2-11 White Balance Adjustment

3-2-11 (A) LOW-LIGHT ADJUSTMENTS

3-2-11 (B) HIGH-LIGHT ADJUSTMENTS

3-2-12 Sub-Brightness Adjustment

3-2-13 Vertical Size Adjustment

3-2-14 Horizontal Size Adjustment

3-2-15 When CRT Is Replaced

3-3 Option Byte Table

Micom : SZM370TH

4. Troubleshooting

4-1 No Power

4-2 No Sound

4-3 Horizontal Line Appears

4-4 No Signal

5. Exploded Views & Parts List

5-1 CT2088BL6X/XAP

6. Electrical Parts List

6-1 CT1488BL6X/XAP (CT1488BL6X/XAP and CT2088BL6X/XAP Dissimilar parts)

ASSY PCB MAIN(OPT)

ASSY-CRT

ASSY-PCB,A/V FRONT

ASSY SPEAKER

ASSY CABINET FRONT

6-2 CT2088BL6X/XAP

ASSY PCB MAIN(OPT)

ASSY CABINET FRONT

ASSY ACCESSORY

ASSY-CRT