- Computers & electronics
- Audio & home theatre
- DVD players
- LG Electronics
- XBV713
- Operating instructions
advertisement
Copying from DVD to VCR
You can copy the contents of a DVD to a VHS tape.
1. Insert the disc you wish to copy into the DVD deck and close the disc tray.
2. Insert a blank VHS video tape into the VCR deck.
3. Find the place on the DVD from which you want to start dubbing using the PLAY, FF, REW and
PAUSE functions.
For best results, pause playback at the point from which you want to record.
4. Press the z (REC/ITR). The DVD goes into PLAY mode and the VCR goes into RECORD mode. If the DVD disc menu appears, you may need to press H (PLAY) manually to begin copying.
5. When the DVD is finished playing, press x (STOP) to end copying.
Notes:
• You must stop the copy process manually when the DVD movie ends, or the unit may replay and record over and over again.
• When you stop the DVD playback during copying, the recording on VCR is stopped automatically.
On-Screen Display - VCR
Some of these functions will be displayed every time the unit is operated.
❶ ❷
PLAY
SP
JAN 1 , MON 2:15 PM
❸
❶ TAPE SPEED DISPLAY
❷ FUNCTION DISPLAY
❹
❸ DATE DISPLAY
❹
CLOCK/ COUNT/
REMAIN DISPLAY
Each press of the ENTER (OK) changes the TV screen in the following sequence.
STOP
SP
JAN 1 , MON 2:15 PM
2:15 PM
0:35:40
REM 1:58
Real-Time Counter
If a tape with contents recorded on it is inserted into the VCR, the real-time counter shows length of the tape running in hours, minutes, and seconds. Press
CLK/CNT to select the real-time counter display.
Every press of CLK/CNT changes the TV screen as illustrated below.
2:15 AM
CLOCK
0:05:25
COUNTER
REM 1:07
REMAINING TIME
Counter Memory
This feature is useful if there is a section of tape you want to view immediately after recording or if you want to return to the same point several times.
1. Begin recording or playing a tape.
2. Press CLK/CNT until the real-time counter is displayed on the TV screen.
3. At the point that you want to locate later, reset the real-time counter to “0:00:00” by pressing CLEAR.
4. Continue to play or record.
5. Press x (STOP) when recording or playback finishes.
6. Press BACKWARD. The tape automatically stops when the tape counter returns to about “0:00:00”.
Tape Remaining
This function displays the amount of time remaining on the tape during recording or playback. Press
CLK/CNT repeatedly until the REM indicator displays on the TV screen during recording or playback.
The remaining tape length may not be displayed correctly depending on the condition of the tape and the kind of the tape (T-140, T-160, or T-210 etc.).
Notes:
• The function displays can be seen displayed on the TV screen for 5 seconds.
• The clock (or tape counter, tape remaining) mode will be displayed until you press ENTER (OK).
• The tape counter and the remaining tape length indicator appear only when a cassette is inserted.
Also, the remaining tape length indicator appears after any tape operation.
21
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 5 Introduction
- 5 Moisture Condensation
- 5 Symbol Used in this Manual
- 5 Symbol Display
- 5 Notes on Discs
- 6 Types of Playable Discs
- 6 Region code
- 6 Notes on Copyrights
- 7 Front Panel
- 8 Remote Control
- 8 About the Remote Control
- 9 Rear Panel
- 10 Preparation
- 10 Basic TV Connections
- 10 Optional TV Connections
- 11 Connection to an Amplifier
- 12 Initial Settings - VCR
- 12 General Operation
- 12 CLOCK
- 12 PROGRAM
- 13 SETUP
- 14 Displaying Disc Information on-screen
- 14 Initial Settings - DVD
- 14 General Operation
- 15 LANGUAGE
- 15 • Menu Language
- 15 • Disc Audio/Subtitle/Menu
- 15 DISPLAY
- 15 • TV Aspect
- 15 • Display Mode
- 16 AUDIO
- 16 • Dolby Digital/DTS/MPEG
- 16 • Sample Freq. (Frequency)
- 16 • DRC (Dynamic Range Control)
- 16 • Vocal
- 16 • Rating
- 16 • Password (Security Code)
- 17 • Area Code
- 17 OTHERS
- 17 B.L.E. (Black Level Expansion)
- 18 Operation
- 18 VCR Tape Playback
- 18 Basic Instructions
- 18 Auto Tracking
- 18 Manual Tracking
- 18 Search
- 19 Slow Motion
- 19 CM SKIP (Commercial Skip)
- 19 VCR Tape Recording
- 19 Basic Instructions
- 19 External Timer Recording
- 20 Instant Timer Recording
- 20 Recording from External Components
- 21 Copying from DVD to VCR
- 21 On-Screen Display - VCR
- 22 Additional VCR Information
- 22 VCR Auto Play System
- 22 S-VHS Quasi Playback (SQPB)
- 23 General Playback Features - DVD
- 24 Additional Features
- 25 Playing an Audio CD or MP3/WMA file
- 25 Programmed Playback
- 25 Repeat Programmed Tracks
- 25 Erasing a Track from Program List
- 25 Erasing the Complete Program List
- 26 Viewing a JPEG file
- 26 Slide Show
- 26 Still Picture
- 26 Moving to another File
- 26 Rotating the picture
- 27 Playing a DVD VR format Disc
- 27 Maintenance and Service
- 28 Reference
- 28 Language Codes
- 28 Area Codes
- 29 Troubleshooting
- 31 Specifications