AC Power. Chauvet CORE
Add to my manuals23 Pages
Chauvet CORE is a versatile LED fixture that offers a wide range of features and use cases for both indoor and outdoor events. With its auto-ranging power supply, it can be used anywhere in the world without the need for a voltage converter. It also features user-selectable DMX channel modes, allowing for various control options. Additionally, the CORE can operate in standalone mode with sound-activated programs, auto programs, and static colors, making it suitable for a variety of applications.
advertisement
3.
S
ETUP
AC Power
The CORE™ 3x3 has an auto-ranging power supply and it can work with an input voltage range of 100~240 VAC, 50/60 Hz.
To determine the product’s power requirements (circuit breaker, power outlet, and wiring), use the current value listed on the label affixed to the product’s back panel, or refer to the product’s specifications chart. The listed current rating indicates the product’s average current draw under normal conditions.
Always connect the product to a protected circuit (circuit breaker or fuse). Make sure the product has an appropriate electrical ground to avoid the risk of electrocution or fire.
Fuse
Replacement
Never connect the product to a rheostat (variable resistor) or dimmer circuit, even if the rheostat or dimmer channel serves only as a 0–100% switch.
Disconnect the product from power before replacing the fuse.
1. Disconnect the product from power.
2. Wedge the tip of a flat-head screwdriver into the slot of the fuse holder.
3. Pry the fuse holder out of the housing.
4. Remove the blown fuse from the holder.
5. Replace with a fuse of the exact same type and rating.
6. Insert the fuse holder back in place and reconnect power.
Spare fuse holder
(inside safety cap)
Installed fuse
(held by plastic clip)
Safety cap
A spare fuse is not included; however, the safety cap has room for a spare.
Always replace a blown fuse with another of the same type and rating.
CORE™ 3x3 User Manual Rev. 1 Page 7 of 23
Power Linking
The product provides power linking via the Edison/IEC outlet located in the back of the unit.
Power Linking
Diagram
1 st Product 2 nd Product 3 rd Product
Additional Products
You can power link up to 3 CORE™ 3x3 units on 120 VAC or up to 7 CORE™ 3x3 units on 230 VAC.
The power linking diagram shown above corresponds to the North American version of the product ONLY! If using the product in other markets, you must consult with the local CHAUVET® distributor as power linking connectors and requirements may differ in your country or region.
Page 8 of 23 CORE™ 3x3 User Manual Rev. 1
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 3 What Is Included
- 3 Unpacking Instructions
- 3 Claims
- 3 Text Conventions
- 3 Symbols
- 3 Disclaimer
- 4 Product at a Glance
- 4 Safety Notes
- 5 Overview
- 6 Dimensions
- 7 AC Power
- 7 Fuse Replacement
- 8 Power Linking
- 8 Power Linking Diagram
- 9 Mounting
- 9 Orientation
- 9 Rigging
- 9 Mounting Diagram
- 10 Coffin Locks
- 11 Control Panel Operation
- 11 Menu Map
- 12 Configuration (DMX)
- 12 Starting Address
- 12 CORE™ 3x3 Sections for DMX Control
- 13 DMX Channel Modes, Assignments, and Values
- 13 31-Channel
- 14 DMX Channel Modes, Assignments, and Values (cont.)
- 14 27-Channel
- 15 DMX Channel Modes, Assignments, and Values (cont.)
- 15 9-Channel
- 16 DMX Channel Modes, Assignments, and Values (cont.)
- 16 5-Channel
- 16 3-Channel
- 17 Configuration (Standalone)
- 17 Sound-Active Mode
- 17 Sound Sensitivity
- 17 Auto Program
- 17 Program Speed
- 18 Static Colors
- 18 Custom Color Mixing
- 18 Dimmer
- 18 Fan Settings
- 19 Master/Slave Mode
- 20 Two-by-Two (2 x 2) Master/Slave Mode
- 20 Placement of Units for Two-by-Two Master/Slave Mode
- 20 Additional Two-by-Two Configurations
- 21 Product Maintenance
- 23 Returns