Operating your Rehab Chair. C.T.M. HS-7200T TILTING, HS-360, HS-7200

HS-7200 Series User's Manual

OPERATING YOUR REHAB CHAIR

Electrical Tilting Function (HS-7200T Only)

1. By pressing tilting button (F)

2. Then pull joystick (H) backward to tilting, chair will be declining, to stop by releasing

the joystick (H).

3. By pushing joystick (H) forward, to inclining chair, will stop when back to the original

position.

B

A

G

D

F E

H

C

Electrical Reclining 180 Degree Function (HS-7200B Only)

1. By pressing reclining button (F)

2. Then pull joystick (H) backward to reclining to any

angles.

3. By pushing joystick (H) forward to inclining chair

back to its original position.

Electrical Elevating Function (HS-7200B Only)

1. By pressing elevating button (G)

2. Then pull joystick (H) backward to adjust to your

desired height.

3. By pushing joystick (H) forward to receding to original

position.

Controller Position Adjustment

By pushing or pulling the controller (I) to desired position.

*When controller adjusted back to normal position,

make sure T shape pin is inside the square tube's

hole.

*Do not driving while operate above

function.

*Watch out for pinch warning.

11

I

HS-7200 Series User's Manual

Armrest Adjustment

By pulling out the flip up armrests plug (J), then rotate the armrest upward until at rear side to get off or get onto the rehab chair.

Armrest Height Adjustment

By releasing height adjustable armrests knob (K), and adjust to desired height, then fasten height adjustable armrests knob into the hole to lock.

J

K

Chair Manual Tilting Angle Adjustment (HS-7200 Only)

By Releasing tilting adjustable knob (L), and lift chair's brace up to target desired height hole, then fasten tilting adjustable knob.

Footrest Adjustment

1. Lift up double footrest (M) as arrows indicated.

2. Rotate double footrest holder (N), hold on footrest holder lever (O) and rotate outward,

then release footrest holder lever.

L

N

N

O

M

L

Legrest Adjustment

1. Adjust to your comfortable position by moving double legrest (P) up & down or left &

right directions.

2. Lift up double legrest (M) as arrows indicated.

3. Adjust bolt (M1), allowed to adjust double legrest (M) up & down or left & right directions.

12

HS-7200 Series footrest angle adjustment knob

User's Manual

Legrest Comfort Adjustment (HS-7200B Only)

By pressing footrest angle adjustment (Q) from the outside, and use hand to lift up legrest

(R) to desired angle, then release footrest angle adjustment (Q), pin will automatic locked in position. (same for other side)

R

P

Q

M

Electrical Legrests Comfort Adjustment (Option)

1.Pressing (S) button until "2" lights up.

2.Moving (S1) to "R" controls right legrest, to "L" controls left legrest.

3.Pulling Joystick (T) backwards, legrest will ascending; pushing forwards, legrest will

descending.

2 S

T

S1

Headrest Comfort Adjustment (HS-7200B Only)

1. Release height adjustable headrest knob (U), then adjust headrest (V) or (V1) to desired

position and fasten the height adjustable headrest knob (U).

2. Adjust headrest (V) or (V1) forward and backward according to your comfort position.

(Headrest (V1) could be turned freely and width size could be adjusted by using hands)

*Owing to the headrest (V) or (V1) brace limited length, needed to fasten screw tightly

on the brace after adjusted.

V

V

U

13

HS-7200 Series User's Manual

Backrest Tilting Adjustment

Release and take off screw (W), adjust backrest to your comfortable angle and target the hole to fasten screw. (same for both side)

Circuit Breaker

When the electric circuit is overloading or malfunctioned the Circuit Breaker will automatically shut off the main power of the chair to ensure safety in performance.

Pressing down the button (X) will regain mobility.

Freewheel levers

For your convenience, C.T.M. HS-7200 is equipped with two free wheel levers.

These levers allow you to disengage the drive motors and maneuver the chair manually.

1.In travelling, set the two metallic levers (Y) to the Drive position.

2.In stop or when the chair is malfunctioned and unable to be mobile, push the levers

(Y) to the Neutral position so the chair is movable by human force.

DO NOT use your chair while the drive motors are disengaged unless you are in the presence of an attendant! DO NOT disengage the drive motors when your chair is on an incline. The chair could roll down on its own, causing injury!

To engage or disengage the free wheel feature:

1. Turn the free wheel levers outward or inward to engage the drive motors.

(See Fig. 26)

It is important to remember that when your HS-7200 is in freewheeling mode, the braking system is disengaged

W

W

X

14

Y