Installation and Setup Guide

7-4

S E C T I O N 8

Specifications & Accessories

• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •

SECURITY CONTROL

2. Electrical:

VOLTAGE INPUT: 16.5VAC from plug-in 25VA minimum transformer

RECHARGEABLE BACKUP BATTERY: 12VDC, 4AH minimum (sealed lead acid type).

Charging Voltage: 13.8VDC.

ALARM SOUNDER: 12V, 2.0 Amp output can drive 12V sirens or can drive one or two 702

(series ) self-contained 20-watt sirens. Do not connect two 702s in parallel.

AUXILIARY POWER OUTPUT: 12VDC, 600mA max.

FUSE: Battery (3A) No. 90–12

3. Communication:

FORMAT SUPPORTED:

ADEMCO Express:

ADEMCO Low Speed:

Radionics/SESCOA:

10 characters/sec, DTMF (multi-frequency) Data Tones,

1400/2300Hz ACK, 1400Hz KISSOFF.

10 pulses/sec, 1900Hz Data Tone, 1400Hz ACK/KISSOFF.

20 pulses/sec, 1800Hz Data Tone, 2300Hz ACK/KISSOFF.

Robofon 8

ADEMCO Contact ID

Robofon Contact ID

LINE SEIZE: Double Pole

DOC Load No.: 3

Can report 0-9, B-F

See description in Communication section.

10 characters/sec., DTMF (multi-frequency) Data Tones,

1400/2300Hz ACK, 1400Hz KISSOFF. same as ADEMCO except 2300Hz ACK

4. Maximum Zone Resistance: Zones 1–8 = 300 ohms excluding EOLR in standard EOLR zones

8-1

Installation and Setup Guide

COMPATIBLE DEVICES

Keypads: 6128RF, 6148, 6150, 6150RF, 6150V, 6160V, 6164

Wireless Receivers: 5881ENL: accepts up to 8 transmitters

5881ENM: accepts up to 16 transmitters

5881ENH: accepts up to system maximum transmitters

5883M: accepts up to 16 transmitters

5883H: accepts up to system maximum transmitters

6128RF: accepts up to 16 transmitters plus 8 wireless keys

6150RF: accepts up to 16 transmitters

5800TM Transmitter Module (used with 5827BD Wireless 2-Way Keypad)

6164 KEYPAD w/WIRED EXPANSION and RELAY

Relay Module:

Internet/Intranet

4204 RELAY MODULE

Communicator: 7845i

EUREKA Network

Interface:

Transformers:

Sounders:

AI4164RS (RS484 LAN)/AI4164ETH (ETHERNET LAN/WAN)

VISTA-12A: XF1 Model 60844CK, Ap11 V/99090/E148-36

VISTA-12E: 16.5VAC, 25VA wired-in transformer

ADEMCO AB-12M 25cm Motorized Bell & Box

ADEMCO 1011BE12M 25cm Motorized Bell & Box

ADEMCO 702 Outdoor Siren

ADEMCO 719 2-Channel Siren

ADEMCO 747 Indoor Siren

ADEMCO 744 Siren Driver

ADEMCO 745X3 Voice Siren Driver

ADEMCO 705-820, 12.5cm Round Speaker

ADEMCO 713 Speaker

System Sensor PA400B (beige)/; PA400R (red) Indoor Piezo Sounder

8-2

Specifications & Accessories

5800 Series Transmitter Input Loop Identification

All of the transmitters illustrated below have one or more unique factory assigned input (loop) ID codes.

Each of the input loops requires its own programming zone (e.g., a 5804's four inputs require four programming zones).

LOOP 4

YOU MUST

ENROLL

THIS

BUTTON

LOOP 4

YOU MUST

ENROLL

THIS

BUTTON

5 8 0 1

ENROLL AS

"UR" OR "RF"

ON

OFF

5804

ENROLL AS "BR"

LOOP 3

LOOP 2

LOOP 1

LOOP 3

LOOP 2

LOOP 1

LOOP 3

LOOP

1

5802MN2

ENROLL AS

"UR" OR "RF"

LOOP 2

LOOP 4

YOU MUST

ENROLL

THIS BUTTON

LOOP 1

SET

HOUSE

CODE

5 8 0 4 B D

ENROLL AS "BR"

LOOP 2

(REED)

LOOP 1

(TERMINALS)

5816

ENROLL AS "RF"

LOOP 2

(REED)

LOOP 1

(PRIMARY)

LOOP 2

(REED)

LOOP 3

(TERMINALS)

LOOP 3

(TERMINALS)

LOOP 1

(TERMINALS)

5 8 1 9

ENROLL AS "RF"

LOOP 2

(AUX.

CENTER)

5 8 1 7

ENROLL AS "RF"

LOOP 3

(AUX.

RIGHT)

LOOP 1

(INTERNAL

SHOCK

SENSOR

5 8 1 9 S ( W H S & B R S )

ENROLL AS "RF"

NOTE: For information on any transmitter not shown, refer to the instructions accompanying that transmitter for details regarding loop numbers, etc.

LOOP 1

LOOP 2

(REED) LOOP 1

(MOTION)

5808

ENROLL AS "RF"

LOOP 1

(TERMINALS)

LOOP 1

ALTERNATE

POSITION

FOR LOOP 2

(Green)

(Red)

(Yellow)

5809

ENROLL AS "RF"

5816MN

ENROLL AS "RF"

5852 (GBD)

ENROLL AS "RF"

5890 / 5890PI

ENROLL AS

"RF" OR "RM"

Compatible 5800 Series Transmitters Table

Model Product

5801

5802

Wireless Panic

Transmitter

Pendant (Personal

Emergency Transmitter)

UR or RF

BR Only

• Four pushbuttons, each with a unique input

(loop) code.

• Programmable responses (e.g., Panic, Arm,

Disarm, etc.)

• Has single pushbutton.

• Usually programmed for response type of 24-

Hr audible or 24-Hr Silent (other zone

5802CP Belt Clip (Personal

Emergency)

BR Only responses are possible).

Same as 5802.

5802MN

5802MN2

Miniature (Personal

Emergency Trans.)

UR or RF Same as 5802.

5804 Wireless Key

Transmitter

BR Only

• Has four pushbuttons, each with a unique input (loop) code.

• Programmable responses (e.g., Arm, Disarm, etc.)

8-3

Installation and Setup Guide

Compatible 5800 Series Transmitters Table

(cont’d)

Model Product

5804BD Bi-Directional

Wireless Key

BR Only

• House ID must be set.

• Requires 5800TM Transmitter Module or 5883

Transceiver.

• Can indicate system status via its 2 LEDs and built-in sounder.

• Has four pushbuttons, each with a unique input (loop) code.

• Operates the system similarly to wired keypads.

5806

5807

5808LST

Wireless

Photoelectric Smoke

Detectors

RF One-piece smoke detectors with a built-in transmitter.

5809

5816

5816MN

5816TEMP

Heat Detector

Door/Window

Transmitters

Low-Temp. Sensor

Transmitter

RF

RF

RF

One-piece rate-of-rise heat detector with a builtin transmitter.

Has two unique input (loop) codes: one for a wired closed circuit contact loop; the other for its built-in reed switch (used with a magnet).

Transmits a fault condition when temperature drops below 45°F.

Has three unique input (loop) codes: one for a

“Primary” contact loop with programmable options; the others for two “auxiliary” closed circuit contact loops.

Transmitter

RF hidden in the frame and edge of a door or window.

• Has a single unique input (loop) code.

• Connects to externally mounted inertia-type shock detector (not supplied).

• Has built-in tampered cover switch.

• Has 3 unique input (loop) codes:

Loop 1: Terminals for a wired, N.C. sensor loop.

Loop 2: For a closed circuit contact loop using the built-in reed switch in conjunction with a magnet.

Loop 3: Terminals for a wired, closed circuit contact loop.

8-4

Specifications & Accessories

Compatible 5800 Series Transmitters Table

(cont’d)

Model Product

5819WHS

5819BRS

Shock Processor

Transmitter

RF • Has built-in shock sensor.

• Has built-in tampered cover switch.

• Has 3 unique input (loop) codes:

Loop 1: Built-in shock sensor loop wired to TB1

(normally closed).

Loop 2: For a closed circuit contact loop using the built-in reed switch in conjunction with a magnet.

5827

5849

5852

5890

5890PI

5899

Wireless Keypad

Keypad

Glassbreak Detector

PR Detector

Magnets

Uses House

ID only

Loop 3: Externally wired, closed circuit loop connected to TB2.

• Can be used to turn the burglary protection on and off.

• Features the same built-in panic functions as wired keypads.

• The keypad is identified as zone “00” on wired keypads when it transmits with a low

Uses House

ID only

RF battery.

• Requires 5800TM Transmitter Module.

• Operates the system similarly to wired keypads, including panics.

• Can indicate system status via its 3 LEDs and sounder.

• Includes 3 panic keys.

• House ID must also be set.

• 5849 requires both sound and shock of breaking glass to cause alarm to be transmitted.

• 5852 uses intelligent acoustic processing.

RF or RM Dual-element passive infrared detector/transmitter with built-in selectable pulse count.

Note: There is a 3-minute lockout between fault transmissions to conserve battery life.

Package of 4 magnets for use with 5816, 5817, and 5819WHS transmitters.

8-5

Installation and Setup Guide

8-6

S E C T I O N 9

Limitations and Warranty

• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •

WARNING

THE LIMITATIONS OF THIS ALARM SYSTEM

While this System is an advanced design security system, it does not offer guaranteed protection against burglary, fire or other emergency. Any alarm system, whether commercial or residential, is subject to compromise or failure to warn for a variety of reasons. For example:

• Intruders may gain access through unprotected openings or have the technical sophistication to bypass an alarm sensor or disconnect an alarm warning device.

• Intrusion detectors (e.g., passive infrared detectors), smoke detectors, and many other sensing devices will not work without power. Battery-operated devices will not work without batteries, with dead batteries, or if the batteries are not put in properly. Devices powered solely by AC will not work if their AC power supply is cut off for any reason, however briefly.

• Signals sent by wireless transmitters may be blocked or reflected by metal before they reach the alarm receiver. Even if the signal path has been recently checked during a weekly test, blockage can occur if a metal object is moved into the path.

• A user may not be able to reach a panic or emergency button quickly enough.

• While smoke detectors have played a key role in reducing residential fire deaths, they may not activate or provide early warning for a variety of reasons in as many as 35% of all fires. Some of the reasons smoke detectors used in conjunction with this System may not work are as follows. Smoke detectors may have been improperly installed and positioned. Smoke detectors may not sense fires that start where smoke cannot reach the detectors, such as in chimneys, in walls, or roofs, or on the other side of closed doors. Smoke detectors also may not sense a fire on another level of a residence or building. A second floor detector, for example, may not sense a first floor or basement fire.

Finally, smoke detectors have sensing limitations. No smoke detector can sense every kind of fire every time. In general, detectors may not always warn about fires caused by carelessness and safety hazards like smoking in bed, violent explosions, escaping gas, improper storage of flammable materials, overloaded electrical circuits, children playing with matches, or arson. Depending on the nature of the fire and/or location of the smoke detectors, the detector, even if it operates as anticipated, may not provide sufficient warning to allow all occupants to escape in time to prevent injury or death.

• Passive Infrared Motion Detectors can only detect intrusion within the designed ranges as diagrammed in their installation manual. Passive Infrared Detectors do not provide volumetric area protection. They do create multiple beams of protection, and intrusion can only be detected in unobstructed areas covered by those beams. They cannot detect motion or intrusion that takes place behind walls, ceilings, floors, closed doors, glass partitions, glass doors, or windows. Mechanical tampering, masking, painting or spraying of any material on the mirrors, windows or any part of the optical system can reduce their detection ability. Passive Infrared Detectors sense changes in temperature; however, as the ambient temperature of the protected area approaches the temperature range of 32° to 40°C, the detection performance can decrease.

9-1

Installation and Setup Guide

• Alarm warning devices such as sirens, bells or horns may not alert people or wake up sleepers if they are located on the other side of closed or partly open doors. If warning devices are located on a different level of the residence from the bedrooms, then they are less likely to waken or alert people inside the bedrooms. Even persons who are awake may not hear the warning if the alarm is muffled by noise from a stereo, radio, air conditioner or other appliance, or by passing traffic. Finally, alarm warning devices, however loud, may not warn hearing-impaired people.

• Telephone lines needed to transmit alarm signals from a premises to a central monitoring station may be out of service or temporarily out of service. Telephone lines are also subject to compromise by sophisticated intruders.

• Even if the system responds to the emergency as intended, however, occupants may have insufficient time to protect themselves from the emergency situation. In the case of a monitored alarm system, authorities may not respond appropriately.

• This equipment, like other electrical devices, is subject to component failure. Even though this equipment is designed to last as long as 10 years, the electronic components could fail at any time.

The most common cause of an alarm system not functioning when an intrusion or fire occurs is inadequate maintenance.

This alarm system should be tested weekly to make sure all sensors and transmitters are working properly. The security keypad (and remote keypad) should be tested as well.

Wireless transmitters (used in some systems) are designed to provide long battery life under normal operating conditions.

Longevity of batteries may be as much as 4 to 7 years, depending on the environment, usage, and the specific wireless device being used. External factors such as humidity, high or low temperatures, as well as large swings in temperature, may all reduce the actual battery life in a given installation. This wireless system, however, can identify a true low-battery situation, thus allowing time to arrange a change of battery to maintain protection for that given point within the system.

Installing an alarm system may make the owner eligible for a lower insurance rate, but an alarm system is not a substitute for insurance. Homeowners, property owners and renters should continue to act prudently in protecting themselves and continue to insure their lives and property.

We continue to develop new and improved protection devices. Users of alarm systems owe it to themselves and their loved ones to learn about these developments.

9-2

Limitations and Warranty

LIMITED WARRANTY

Honeywell International Inc., acting through its Security & Custom Electronics business ("Seller") 165

Eileen Way, Syosset, New York 11791, warrants its product(s) to be in conformance with its own plans and specifications and to be free from defects in materials and workmanship under normal use and service for 24 months from the date stamp control on the product(s) or, for product(s) not having a manufacturer’s date stamp, for 12 months from date of original purchase unless the installation instructions or catalog sets forth a shorter period, in which case the shorter period shall apply. Seller's obligation shall be limited to repairing or replacing, at its option, free of charge for materials or labor, any product(s) which is proved not in compliance with Seller's specifications or proves defective in materials or workmanship under normal use and service. Seller shall have no obligation under this

Limited Warranty or otherwise if the product(s) is altered or improperly repaired or serviced by anyone other than Honeywell factory service. For warranty service, return product(s) transportation prepaid, to Honeywell Factory Service, 165 Eileen Way, Syosset, New York 11791.

THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED, OF MERCHANTABILITY, OR FITNESS FOR A

PARTICULAR PURPOSE OR OTHERWISE, WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE

HEREOF. IN NO CASE SHALL SELLER BE LIABLE TO ANYONE FOR ANY CONSEQUENTIAL OR

INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED,

OR UPON ANY OTHER BASIS OF LIABILITY WHATSOEVER, EVEN IF THE LOSS OR DAMAGE IS

CAUSED BY THE SELLER'S OWN NEGLIGENCE OR FAULT.

Seller does not represent that the product(s) it sells may not be compromised or circumvented; that the product(s) will prevent any personal injury or property loss by burglary, robbery, fire or otherwise; or that the product(s) will in all cases provide adequate warning or protection. Customer understands that a properly installed and maintained alarm system may only reduce the risk of a burglary, robbery, fire, or other events occurring without providing an alarm, but it is not insurance or a guarantee that such will not occur or that there will be no personal injury or property loss as a result. CONSEQUENTLY,

SELLER SHALL HAVE NO LIABILITY FOR ANY PERSONAL INJURY, PROPERTY DAMAGE OR

OTHER LOSS BASED ON A CLAIM THAT THE PRODUCT(S) FAILED TO GIVE WARNING.

HOWEVER, IF SELLER IS HELD LIABLE, WHETHER DIRECTLY OR INDIRECTLY, FOR ANY

LOSS OR DAMAGE ARISING UNDER THIS LIMITED WARRANTY OR OTHERWISE,

REGARDLESS OF CAUSE OR ORIGIN, SELLER'S MAXIMUM LIABILITY SHALL NOT IN ANY

CASE EXCEED THE PURCHASE PRICE OF THE PRODUCT(S), WHICH SHALL BE THE

COMPLETE AND EXCLUSIVE REMEDY AGAINST SELLER.

This warranty replaces any previous warranties and is the only warranty made by Seller on this product(s). No increase or alteration, written or verbal, of the obligations of this Limited Warranty is authorized.

9-3

Installation and Setup Guide

9-4

S E C T I O N 1 0

Index

• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •

1321 .......................................2-5

1321X10......................2-16, 2-17

24-Hour Audible Alarm ...........3-6

24-Hour Auxiliary Alarm..........3-6

24-Hour Silent Alarm ..............3-6

3+1 and 4+1 Standard

Formats ............................6-2

4204 .1-2, 1-3, 2-7, 2-9, 2-15, 3-1,

5-12, 5-13, 6-8, 8-2

4219 ..1-1, 1-2, 1-3, 2-7, 2-10, 8-2

4229 .1-1, 1-2, 1-3, 2-7, 2-9, 2-10,

2-11, 2-15, 3-1, 5-12, 5-13,

6-8, 8-2

4-Wire Smoke Detectors.........2-9

5137AD ...........................2-3, 3-9

5800 Series

Transmitters ... 2-13, 8-3, 8-4,

5800TM...........2-13, 8-2, 8-4, 8-5

5801 ..............................2-13, 8-3

5802 .....................2-13, 6-11, 8-3

5802CP ................2-13, 6-11, 8-3

5804 wireless key...................5-8

5804BD wireless key ..............5-8

5827 .......................2-13, 4-2, 8-5

5827BD ...........2-13, 4-2, 8-2, 8-5

5881 .......................................1-2

6128 .......................................2-3

6139 ................................2-3, 3-9

9-pin connector.....................2-14

AAV Connections .................2-19

AC Transformer......................2-5

AD12612 ................................2-3

Alarm Bell Timeout .................4-3

Alarm Output ...................1-2, 2-5

Alarm Sounder Timeout..........4-3

Alpha Descriptor..............5-1, 5-5

Alpha Keypads .......................3-9

Alpha Programming................3-1

Arm Away/Stay Report

Code ................................4-8

Arm–Away..............................3-7

Arming Away ..........................6-7

Arming Instant ........................6-7

Arming Modes ........................6-7

Arming Stay............................6-7

Arm–Stay ...............................3-7

Audio Alarm

Verification .....1-2, 2-18, 4-12

Audio Alarm Verification

(AAV) ............................. 2-18

Authority Levels ..................... 6-6

Backup Battery ..................... 1-2

Battery Life ......................... 2-13

Battery Tests ................. 7-1, 7-3

Bell Supervision.................... 2-5

Bell Supervision Jumper ....... 2-5

Bypassing Zones .................. 6-8

Cabinet ................................. 2-1

Character List ..................... 5-21

Charging Voltage.................. 8-1

Chime By Zone..................... 4-2

Chime Mode ......................... 6-8 common zone ....................... 3-2

Communication... 5-20, 6-1, 7-3,

8-1

Contact ID Reporting ............ 8-1

Data Field Programming

Procedures ...................... 3-9

Defining Output Functions .. 5-14

Descriptor Programming ..... 5-20 device address .. 2-3, 2-11, 2-15,

3-1, 3-11, 4-2, 4-20, 5-12,

6-11

Device number5-1, 5-2, 5-3, 5-4,

5-5, 5-6, 5-7, 5-8, 5-9, 5-10,

5-13, 5-14, 5-15, 5-16, 5-17,

5-18, 5-19, 5-20, 5-24

DIP Switches. ..................... 2-13

Disarm.................................. 3-7

Disarming ............. 5-16, 6-7, 6-8

Double-Balanced .................. 2-8

Enrolling ...................... 2-13, 5-1 entering serial number .......... 5-7

Entry Delay.... 3-6, 4-8, 6-7, 6-11

Entry Delay 02 ...................... 4-3

Entry/Exit Burglary ................ 3-5

EOLR ............................ 2-8, 8-1

Event Logging.............. 1-1, 4-11

Exit Error Alarm .................... 6-5

Exit Error Alarm .................. 6-11

Exit Error Report Code ......... 4-8

Expander Module

Addresses............. 2-10, 2-11

Expansion Zones1-3, 2-10, 2-11,

2-15

Expert Programming

Mode................ 5-1, 5-6, 5-10

Factory Defaults ..................3-10

Fault Delay Time .................4-11

Fire Sounder Timeout............4-3

Forced Bypass Function........4-1

Function Key Programming ..1-3,

3-1, 5-18, 5-19

Function Keys ...............3-4, 5-19

Fuse.......................................8-1

Go/No Go Test Mode .............7-2

Handshake.............................6-1 hardwired zones............. 1-1, 5-3

HAYES Modem......................1-1

House ID........ 2-13, 4-2, 8-4, 8-5

IBM Personal Computer.........3-1

Input Device Type .. 5-7, 8-3, 8-4,

8-5

Installer Code. 3-10, 4-1, 7-1, 7-3

Interior Follower ............3-5, 5-16

Interior w/Delay .............3-6, 5-16 keypad addresses.......... 2-3, 3-3

Keypad Programming

Fields..............................4-19

Keyswitch.............. 2-14, 3-7, 6-5

Kissoff...........................5-16, 6-1

Lock .......................................2-1

Long Range Radio 1-2, 2-18, 4-6,

4-7, 6-5

Low Battery Message.............7-3 macros...................................1-1

Master Security Code.............4-1 model 112 ............................2-14

Modem..........................3-1, 6-12

Module Addresses ...............5-13 momentary switch ................2-14

No Alarm Response......3-7, 5-16

Normally Closed Zones..........2-8

Normally Open Zones ............2-8 on-board triggers..................2-19

On-Board Triggers ...............2-17

Output Device Mapping.3-1, 5-12

Output Devices ..... 3-4, 5-12, 6-8

Output Functions..................5-12

Output relays .........................1-2

Output To Long Range

Radio................................4-2

PABX Access Code ...............4-4

Pager #1 Phone No....4-13, 4-14

Pager Format.......................4-14

Pager Programming ......3-4, 4-13

10-1

Installation and Setup Guide

Pager Programming Fields ..4-13

Pager Report Options ..........4-14

Paging .................................4-12

Panic Keys.............................6-8

Partitions................................3-2

Perimeter Burglary .................3-5

Phone Line ..........................2-18

Phone Module…….1-1, 2-4, 2-7,

2-19, 4-13

Power Failure .............5-16, 6-12 power supply ...........2-3, 2-5, 9-1

Power Up In Previous State...4-4

Powerline Carrier Device (X-10)

House ID ..........................4-2

Powerline Carrier

Devices ............1-2, 2-16, 6-8

Primary Phone No. ................4-7

Primary Phone No. ................4-4 prompt to confirm ..................5-8

Quick Arm Enable .................3-3

Relay Module Addresses.....2-15

Relay Modules..............1-3, 2-15

Relay Programming...............3-1

Remote Keypads...................1-2

Report Code..3-3, 4-8, 4-9, 4-11,

5-2, 5-3, 5-7, 6-1

Report Code Formats ............6-1

Reports In Armed Period..... 4-12 response time ..... 2-10, 4-11, 5-2

RF House ID Code......... 3-3, 4-2

RF Interference ................... 2-12

RF jam detection................... 1-1

RF Jam Option...................... 3-3

RF Motion ............................. 5-3

RF Receiver... 2-4, 2-7, 2-12, 6-5

Ring Detection Count For

Downloading .................. 4-13

RJ31X Jack......................... 2-18

Schedules ........................... 5-23

Secondary Phone No. ........... 4-5

Security Codes............... 1-1, 6-6

Silent Burglary ...... 3-7, 5-16, 6-5

Silent Panic........................... 6-8

Single Alarm Sounding

Per Zone .......................... 4-3

Smoke Detectors .................. 8-4

Sniffer Mode ........... 5-5, 7-1, 7-2 sounder connections ............. 2-5

Supervised Fire..................... 3-6

Supplementary Power........... 2-3

Swinger Suppression .......... 4-12

System Communication . 5-2, 6-1

System Operation 4-1, 5-8, 5-10,

5-16, 5-24

System Status Report Codes.4-7

System Test ..........................7-1 tamper switch.......................2-14

Telco Line ..............................6-5

Telephone Line Monitoring.....1-1

Test Mode...................... 7-1, 7-2 touchpads ..............................4-8

Transmitter Battery Life........2-13

Transmitter Input Types .........5-3

Trouble by Day/......................3-5

Trouble Displays ..................6-11

Verify Operation .....................2-9

Wireless Key Programming

Templates.........................5-8 wireless key templates ...........5-8

Wiring Length/Gauge Chart....2-3

Wiring Run Chart ........... 2-3, 2-4

Worksheet..............................2-7

Zone Doubling .......................2-8

Zone List ................................3-1

Zone Lists ............3-1, 5-17, 5-18

Zone Not Used.......................3-5

Zone Programming ................5-1

Zone Programming

Procedure....................... 5-1

Zone Type..............................5-7

Zone Types.... 2-8, 3-5, 5-2, 5-16

10-2

}

}

TH GROUPS)

16

ADDITIONAL ZONES

OPTIONAL FOR UP TO

( FROM EITHER OR BO

LO

HI

HI

HI

LO

LO

LO

HI

HI

HI

LO

LO

NOT USED

ZONE 1

ZONE 6

ZONE 5

ZONE 4

ZONE 3

ZONE 2

}

AD

OUT A TA

IN FROM KEYP A TA

KEYP AD D

+

) AD PWR (

KEYP AD

GREEN: D

YELLOW:

GROUND (- ) RETURN

BLACK:

RED: KEYP

165 Eileen Way, Syosset, New York 11791

Copyright © 2005 Honeywell International Inc.

www.honeywell.com/security

ÊK10022-1V1CŠ

K10022-1V1 10/05 Rev. A