advertisement
531526-1_A - 747c_&_777c2_Man_Eng.qxp 10/2/2006 1:42 AM Page 59 www.reelschematic.com
Water Type
(Advanced)
Water Type configures your unit for operation in fresh or salt water. The Water
Type menu choice is available when User Mode is set to Advanced (see Setup
Menu Tab: User Mode).
NOTE: In salt water, what would be considered a large fish might be 2 to 10 times bigger than a large fish in fresh water (depending on the type of fish you are seeking). The salt water setting allows for a greater range in fish size adjustment to account for this. Also, make sure that the Water Type is set accurately, especially in salt water, as this affects the accuracy of deep water depth readings.
To change the Water Type setting:
1. Make sure you are in Advanced User Mode, then highlight Water Type on the Sonar main menu.
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the Water
Type setting. (Fresh, Salt, Default = Fresh)
Transducer Select
Transducer Select allows you to select which transducer you want to use (the Fishing System comes with a DualBeam PLUS™ transducer, and also supports the optional-purchase QuadraBeam PLUS™ and
WideSide® transducers.)
To change the selected Transducer:
1. Highlight Transducer Select on the Sonar Main menu.
2. Use the LEFT or RIGHT 4-WAY Cursor Control keys to change the transducer selected. (DualBeam, QuadBeam, WideSide, Universal
Sonar 2, Default = DualBeam)
54
531526-1_A - 747c_&_777c2_Man_Eng.qxp 10/2/2006 1:42 AM Page 60 www.reelschematic.com
Alarms Menu Tab
From any view, press the MENU key twice to access the Main Menu System. The Alarms tab will be the default selection.
NOTE: When an alarm is triggered, you can silence it by pressing any key. The alarm will be silenced, and will not be triggered again until a new instance of the alarm condition is detected.
Alarms Menu
55
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 8 DualBeam PLUS™ Sonar
- 9 QuadraBeam PLUS™ Sonar (with optional-purchase QuadraBeam PLUS™ transducer)
- 10 WideSide® Sonar (with optional-purchase WideSide® transducer)
- 11 Universal Sonar
- 15 Sonar View
- 16 Understanding Sonar History
- 17 Real Time Sonar (RTS®) Window
- 17 Freeze Frame and Cursor
- 18 Bottom Presentation
- 20 Sonar Zoom View
- 21 200/83 kHz Split Sonar View
- 22 Big Digits View
- 23 Circular Flasher View
- 27 WideSide® View (with optional-purchase WideSide® transducer)
- 28 POWER/LIGHT Key
- 28 VIEW Key
- 29 MENU Key
- 29 4-WAY Cursor Control Key
- 30 EXIT Key
- 35 Normal Operation
- 36 Simulator
- 37 System Status
- 37 Self Test
- 38 Accessory Test
- 38 PC Connect (with PC Connect Cable Only)
- 40 Side (WideSide® transducer: WideSide® view only
- 41 Sensitivity
- 42 Upper Range (Advanced: Sonar, Split Sonar, Big Digits and Circular Flasher Views only)
- 43 Lower Range
- 44 Side Beam Range (WideSide® transducer: WideSide® view only)
- 45 Chart Speed
- 46 Zoom Level (Sonar Zoom view only)
- 46 Bottom Lock
- 47 Bottom Range (Sonar Zoom View only, when Bottom Lock is On)
- 49 Beam Select
- 50 Fish ID
- 51 Fish ID Sensitivity
- 51 Real Time Sonar (RTS®) Window
- 52 Bottom View
- 52 Zoom Width
- 53 83 kHz Sensitivity (Advanced)
- 54 455 kHz Sensitivity (Advanced, with QuadraBeam PLUS™ transducer)
- 55 WideSide® Sensitivity (Advanced, with WideSide® transducer)
- 56 Depth Lines (Advanced)
- 57 Surface Clutter (Advanced)
- 58 Noise Filter (Advanced)
- 58 Max Depth (Advanced)
- 59 Water Type (Advanced)
- 59 Transducer Select
- 61 Depth Alarm
- 61 Fish ID Alarm
- 62 Low Battery Alarm
- 62 Aux. Temp. Alarm (with optional-purchase temp. probe or Temp/Speed only)
- 63 Temp Alarm
- 63 Alarm Tone
- 65 Units - Depth
- 65 Units - Temp (International only)