B. Hydraulic Oil. Cub Cadet 29HP Tank, 53AJ8CTX750, 29HP Tank 53AJ8CTX750
Add to My manuals32 Pages
advertisement
Height of Cut Clevis Pin
Main Frame
Figure. 6
Linch Pins
Linch Pins levels. Bahia blades are configured without offset, and with a maximum amount of sharpened cutting edge.
Mulch- These blades are generally designed for use in cutting decks equipped with mulch baffles. The shape of the blade generally produces higher turbulence in order that the grass can be repeatedly cut and re-cut into smaller pieces. These blades generally require more horsepower than other blades.
Mulch blades work best when the grasses are cut at the highest levels, minimal lengths of grasses are removed, and grass conditions are generally dry.
MAINTENANCE AND
SERVICE
WARNING:
Disconnect the spark plug wires or remove the key from the ignition to prevent the engine from accidentally starting before performing any maintenance on this mower.
A. Mower Deck
1.
Removing the Mower Deck: a.
Apply the parking brake. Remove ignition key and both spark plug caps.
b.
Lower the cutter deck to the ground. Capture the lift handle by placing the height of cut clevis pin in the “lock” position.
c.
Remove tension of the PTO belt by moving the belt tensioning rod.
Note:
There is a certain amount of spring tension due to the weight of the deck. When removing the lift linkage from the deck the tension of the springs will go from the deck to the lift handle. Not capturing the lift handle while removing the lift linkage from the deck will cause it to snap back.
d.
Detach the mower drive belt.
e.
Remove six linchpins (See Fig. 6) (4) from the deck and (2) from the front of the mower. Remove the linchpins on the left and right rear side of the cutter deck (2); remove the linchpins on the left and right front side of the cutter deck (2); and remove the linchpins on the front of the mower (2).
f.
Turn front caster wheels outward.
g.
Shift the deck toward the ignition switch side of the mower and remove.
h.
To install reverse the process.
2.
Changing a Blade: a.
Remove the Key from the ignition and disconnect the spark plug.
b.
Jack up the front of the mowing deck about one foot and block it in that position.
c.
Wrap a rag around one end of the blade and grasp it to prevent it from turning, or secure the blade by placing a block of wood between the blade and the deck housing.
17
advertisement
Related manuals
advertisement
Table of contents
- 3 Foreword
- 4 General Safety Operations
- 4 A.Danger
- 4 B. Warning
- 4 C. Caution
- 4 Safety Precautions
- 4 A. General
- 5 B. Related to Fuel
- 5 C. Related to Batteries
- 5 D. When Mowing
- 6 E. Towing
- 7 Safety Decals
- 8 Specifications
- 9 Operating Instructions
- 9 A. General
- 10 B. Controls
- 12 C. Initial Adjustments
- 13 D. Zero Turn Break-In and Operating Procedures
- 15 E. Mower Cutting Blades
- 16 Maintenance and Service
- 16 A. Mower Deck
- 17 B. Hydraulic Oil
- 18 C. Electrical System
- 20 D. Tires
- 21 E. Brakes
- 22 F. Hydraulic System
- 23 G.Storage
- 24 Maintenance Schedule
- 26 Performance Adjustments
- 26 A. High Speed Tracking Adjustment
- 26 B. Engine RPM Check and Adjustment
- 27 C. Deck Corner Ball Wheel Roller Settings
- 27 D. Deck Center Anti-Scalp Roller Settings
- 27 E Lap Bar Adjustment
- 28 F Deck Leveling Procedure
- 29 Wiring Diagram