Configuring Home City Settings. Casio (W3), MRG-8000B

Operation Guide 5011 (W3)

Configuring Home City Settings

2.

Press the D move the indicator hand clockwise.

Use the procedures in this section to configure Home City settings, including selecting a region and city code, setting the time and date, etc. You also can use the procedures in this section to adjust the time and date when the watch is unable to receive a time calibration signal for some reason.

• Always use the Timekeeping Mode to configure and adjust Home

Time settings.

• Each press of the C button cycles through available settings in the sequence shown below.

• Home City

• Summer time Hour and minute

Day

Year

Month

■ To select your Home City and change its summer time setting

1.

In the Timekeeping Mode, depressed (for about five seconds) as the indicator hand goes through the following sequence.

• The indicator hand will move to the last signal reception result (“Y” or “N”), then to

“READY” (or “R” for some models), and then the city code of the currently selected

Home City. Next, the second

Second hand

30

Indicator hand hand will move to “0” (“60” for some models).

• The watch will return to normal timekeeping automatically if you do not perform any operation for about two or three minutes. Any changes you have made to settings up to that point will be saved.

3.

Press the B cycle through the summer time (DST) settings described below.

30

30

(+)

••••• AT (AUTO)

This setting enables the auto summer time setting, which turns summer time on or off in accordance with the received time calibration signal.

This is the factory default setting for the following city codes:

LON, PAR, ATH, TYO, ANC, LAX, DEN, CHI, NYC.

• This setting is available for the following city codes only:

LON, PAR, ATH, HKG, TYO, HNL, ANC, LAX, DEN, CHI,

NYC.

••••• ON

This setting turns on summer time and advances the current time by one hour from standard time.

••••• OFF

This setting turns off summer time and displays standard time.

• Signal reception is possible in the time zones represented by

HKG (Hong Kong), HNL (Honolulu), and ANC (Anchorage) when reception conditions are good.

• If you want to proceed with adjusting the current time and date setting, continue from step 2 under “To adjust the current time and date setting manually.”

4.

When everything is the way you want, press the A button.

• This will apply your settings and return to normal timekeeping.

The second hand will move to and start timekeeping from the appropriate seconds count in accordance with the watch’s internal timekeeping.

■ To adjust the current time and date setting manually

1.

In the Timekeeping Mode, depressed (for about five seconds) as the indicator hand goes through the following sequence.

• The indicator hand will move to the last signal reception result (“Y” or “N”), then to

“READY” (or “R” for some Second hand

30 models), and then the city code of the currently selected

Indicator hand

Home City.

• At this time the second hand will move to “0” (“60” for some models).

• The watch will return to normal timekeeping automatically if you do not perform any operation for about two or three minutes. Any changes you have made to settings up to that point will be saved.

2.

Press the C

• The indicator hand will move to 12 o’clock, and the day of the week hand will move to

“0” (“60” for some models).

30

3.

Use the D buttons to change the time setting in one-minute increments.

24-hour hand

(–)

• Holding down either button will cause the hands to move at high speed. Once started, high-speed hand movement will continue even if you release the button. To stop high-speed hand movement,

30 press any button.

• Check the 24-hour hand to make sure that the time is set properly (1:00 a.m. = 1 o’clock, 1:00 p.m. = 13 o’clock).

(+)

4.

Press C year setting.

Tens digit

30

Units digit

5.

Use the D the units digit hand button to move the tens digit hand clockwise.

20X8

20X9

20X0

20X1

20X2

20X7

20X6

20X5

20X4

20X3

30

• Use the B button to move the tens digit (indicator) hand clockwise.

200X

20X1

20X2

20X9 20X3

20X8

20X7

20X6

20X5

20X4

6.

Press C month setting.

30

Moves to the current month setting.

7

7.

Press the D move the indicator hand clockwise one month.

30

Oct

Nov

Dec

Jan

Feb

Sep Mar

Aug

Jul

Jun

May

Apr

8.

Press C day setting.

30

Operation Guide 5011 (W3)

9.

Use the D buttons to change the day setting in one-day increments.

(–)

30

(+)

Day

10.

When everything is the way you want, press the

• This will exit the setting procedure and reset the seconds count to zero.

• Press A to restart timekeeping on a time signal on the TV or radio.

• The day of the week is calculated automatically.

30

In areas where date data can be received with the calibration signal, the watch will adjust automatically for leap years and months of different lengths. In areas where reception of a time calibration is not possible you will need to adjust the date manually for leap years and months of different length.

8