- Computers & electronics
- Cameras & camcorders
- Camera accessories
- Camera housings
- JVC
- WB-1550U
- Operating instructions
Assembling the Housing. JVC WB-1540U, WB-1550U
Add to my manuals16 Pages
JVC WB-1540U is an outdoor housing compatible with the cameras TK-C625U/E and VN-C625U. To get started with the device, you will need to disassemble the housing, mount the camera, and then assemble the housing again. The assembled housing can then be mounted to a wall. The device is equipped with slots and openings for ventilation to ensure reliable operation and protect it from overheating. It is crucial to avoid blocking these openings to ensure proper functioning.
The WB-1540U is designed to provide protection for the camera in outdoor environments. It is important to carefully consider the installation location to ensure the longevity of the attached camera, especially regarding temperature and sunlight exposure. Additionally, using SanDisk industrial CF cards is recommended when using the device with the VN-C625U camera.
advertisement
WB-1540_1550.book Page 8 Thursday, May 17, 2007 3:21 PM
Installation and Connection (WB-1540U)
Assembling the Housing
Safety Wire
Desiccant
1.
2.
Main Housing Unit
Screw A (M4 x 6) x 3
Lower Housing
Position Mark
Gasket
3.
Gasket Gland
1.
Adhering the desiccant
Use a tape to adhere the supplied desiccant to the interior of the lower housing.
CAUTION:
● Fogging may occur when there are drastic temperature changes. In this case, continue using without turning off the power.
● Pay attention when handling the desiccant in order to maintain its effectiveness.
• Do not remove it from the bag until you are about to use it.
• Do not wet it or touch it with wet hands.
• Assemble promptly upon adhering the desiccant.
• Be sure to replace the desiccant during maintenance.
2.
Mount the lower housing
Mount the lower housing that is dismantled in Step 2.
( A pg. 10) to the main housing unit using the 3 Screws A
(M4 x 6).
Do so by aligning the position marks of the lower housing and the main housing unit.
3.
Mount the gasket and gasket gland
Mount the gasket and gasket gland that are dismantled in
Step 1. ( A pg. 10) of the housing disassembly procedure
to the lower housing using the 6 Screws B (M4).
Screw B (M4) x 6 CAUTION:
● During assembly, ensure that wires and cables are not caught in the housing.
● Do not exert force unnecessarily on the gasket or twist it during mounting.
● Check to ensure that the gasket is in close contact with the camera.
Mounting the Housing to the wall
Safety Wire
Anchor Bolt
(M8, 35 mm and above)
Washer
Nut
Installation Position
1. 2.
152
126
63
1.
Drill a hole into the wall.
Drill a hole ( R 45 mm) for inserting the connection cable.
(Refer to left fig.)
2.
Affix anchor bolts onto the wall.
• Affix 4 anchor bolts (M8, 35 mm and above) for attaching the housing. (Refer to left fig.)
• Affix an anchor bolts for attaching the safety wire, in the middle (about 60 mm from both ends) of the 2 upper anchor bolts, 30 mm from the top. (Refer to left fig.)
3.
Mount the safety wire and arm to the wall.
• Mount the safety wire attached to the housing, to the anchor bolts using the nut and wire.
• Use the nut and wire to mount the housing onto the wall.
45
8
WB-1540_1550.book Page 9 Thursday, May 17, 2007 3:21 PM
Mounting the Housing to the Wall (continued)
Waterproofing
8.
4.
9.
4.
Open the cable connection cover
Use provided hexagon wrench to remove the 4 screws
(M3 x 12) from the cable connection cover to open it.
5.
Connect each cable
Connect the necessary cables.
NOTES:
● When connecting to TK-C625U/E, ensure to bind connectors of LAN cables that are not in use with an insulating tape before using.
● Ensure to bind the DC 12 V Power Cable that is not in use on this system with insulating tape.
Screw (M3 x 12) x 4
Alarm/Communication Cable
Coaxial
Video Cable
AC 24 V
Power Cable
LAN Cable (Male)
T
DC 12 V Power Cable
7.
8.
Hole
Waterproofing
5.
Bind with insulating tape
T
Not in use on this system.
Bind using a waterproof
(adhesive) tape
6.
6.
Bind cable using a waterproof tape
Upon connecting, ensure to perform waterproofing procedures by binding the joint of each cable with a waterproof (adhesive) tape.
CAUTION:
For safety reasons, turn on the power only upon connecting all cables.
7.
Fasten the cables in the interior of the arm
When waterproofing is complete, insert the cables into the upper interior of the arm and fasten using a tape.
CAUTION:
When inserting the cables, ensure that all cable connections are above the cable connection cover (see dotted line in the left diagram 7.).
Failure to do so may cause malfunctions due to penetration of rain water.
8.
Cover the hole and the mounting side of housing with waterproof seal.
After the cables have been connected, cover the holes made in step 1. with waterproof seal. With the Cable connection cover open, put your hand in and cover the hole. Cover the mounting side of the housing with waterproof seal.
NOTE:
● Be sure to perform waterproofing. Seepage of rainwater may result in malfunction.
● Use GE silicon or its equivalents as the sealing material.
9.
Close the cable connection cover
When cable connection is complete, close the cable connection cover and fasten 4 screws (M3 x 12) removed in step 4. using the provided hexagon wrench.
9
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
Frequently Answers and Questions
What cameras are compatible with the WB-1540U?
What should be kept in mind when choosing an installation location for the WB-1540U?
What specific CF card is recommended for use with the WB-1540U?
advertisement
Table of contents
- 4 Table of Contents
- 4 Operating Precautions
- 5 System Example
- 5 VN-C625U and VN-C655U Systems
- 5 TK-C625U/E, TK-C655E and TK-C676E Systems
- 6 Disassembling the Housing
- 6 Mounting the Camera
- 6 TK-C625U/E
- 7 VN-C625U
- 8 Assembling the Housing
- 8 Mounting the Housing to the wall
- 10 Disassembling the Housing
- 10 Procedures Before Mounting the Camera
- 11 Mounting the Camera
- 11 TK-C655E and TK-C676E
- 12 VN-C655U
- 13 Assembling the Housing
- 13 Mounting the Housing to the wall
- 15 Specifications
- 15 WB-1540U
- 15 WB-1550U