advertisement
VadaTech AMC72X User’s Manual
Interface eth0 eth1 eth2 eth3 eth4 eth5
Default IP Address
192.168.42.212
N/A
192.168.40.212
192.168.41.212
192.168.1.199
192.168.2.199
Type
XAUI
N/A
GbE
GbE
GbE
GbE
Port
AMC Ports 8-11
Not Connected
AMC Port 0
AMC Port 1
Front Port 0
Front Port 1
Table 22: AMC723 Network Device Mapping
NOTE: Only first 10GbE port is connected to AMC Ports. Second port is unconnected and shows up as a dummy port in Linux. It cannot be used.
VNC Server
The Linux GUI can be accessed remotely over the network since there is a VNC server installed in the
Linux. The server is preconfigured and ready to use, but it is off by default. Use the command bellow to start VNC server:
# vncserver :1 -geometry 800x600 -depth 24
The following command stops VNC server:
# vncserver -kill :1
The password for VNC server is same as password for root user.
6.3 Graceful Shutdown Support
Graceful shutdown provides a way of gracefully shutting down the OS running on the board once payload deactivation request from uTCA Carrier is received due to explicit deactivation command or AMC handle opened.
Graceful shutdown a result of cooperation of different components of AMC design which are described below:
1. IPMI Controller supports a. OEM IPMI commands which allow the user to enable/disable graceful shutdown support b. Read the Quiesced state of the AMC to determine whether AMC deactivation has been requested by uTCA Carrier Manager c. Monitor of CPU power state to detect system shutdown completion
2. Hardware support a. I2C path to payload CPU which enables OS communication to IPMI Controller
3. Application running on OS side a. Performs AMC Quiesced state monitoring through i2c using OEM IPMI commands and gracefully shuts down the OS once deactivation is requested by uTCA Carrier Manager.
VADATECH FORM No. 3WI731-01 Rev. B
VT-MAN-CUS-100569-2.1.0
Page 26 of 34
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 7 Overview
- 7 Applicable Products
- 7 Document References
- 8 Acronyms Used in this Document
- 9 Hardware Overview
- 9 Block Diagram
- 10 Board Layout
- 11 Front Panel Layouts
- 12 Temperature Sensors
- 13 IPMI Management Interface
- 14 IPMI Internal 10/100 Ethernet
- 15 DIP Switch Settings
- 15 IPMI Related functions
- 15 Write Protection Switches
- 15 Board Configuration Switches
- 16 SRIO Configuration Switches
- 17 Gladden Interface
- 17 Serial Console Port
- 17 USB Ports
- 18 1GbE Ports
- 18 XAUI Ports (only applicable to AMC721 and AMC723)
- 19 SRIO Ports (only applicable to AMC722)
- 19 SD Card Socket
- 20 CaveCreek EEPROM
- 20 DDR3 SO-DIMMs
- 21 Ethernet PHY Addressing
- 22 Software
- 25 Linux
- 26 Graceful Shutdown Support
- 27 Implementing Graceful Shutdown
- 28 IPMI E-Keying Configuration
- 29 Serial Over Lan (SOL)
- 30 Factory Setup
- 30 Initial Factory Setup
- 30 Writing the Factory Default SD Card Contents
- 32 AMC725 Specific Changes
- 32 Block Diagram
- 32 Summary
- 33 Switches and Sensors