Cleaning and Care. Samsung BF665CCST

Cleaning and Care

Oven exterior

● For cleaning both the interior and exterior of the oven, use a cloth and a mild cleaning agent or warm soapy water.

● Dry with kitchen paper or a dry towel.

● Do not use scourers, caustic cleaners or abrasive products.

Stainless steel oven fronts

● Do not use steel wool, scouring pads or abrasives. They may damage the finish.

Aluminium oven fronts

● Wipe the plate gently with a soft cloth or microfiber cloth and a mild window cleaning detergent.

WARNING

Make sure the oven is cool before cleaning.

Oven interior

● Do not hand - clean the door seal.

● Do not use coarse scouring pads or cleaning sponges.

● To avoid damaging the enameled oven surfaces, use commercially available oven cleaners.

● To remove stubborn soil, use a special oven cleaner.

Accessories

Wash all bakeware and accessories after each use and dry with a kitchen towel.

To clean easily, soak in warm soapy water for about 30 minutes.

EN

BF665CCST_HAC-00091V_EN.indd 33

33

2007-06-07 ｿﾀﾀ・9:16:11

EN

Cleaning and Care (continued)

Catalytic enamel surface

The cover casing is coated with a dark gray catalytic enamel that can become coated with oil and fat distributed by circulating air during convection heating. These deposits will burn off at oven temperatures of 200 °C and higher, for example, when baking or roasting. Higher temperatures will result in faster burning.

The oven and accessories should be cleaned after each use. Otherwise further baking and roasting will cause the deposits to bake on even harder and cleaning may become difficult and in extreme cases impossible.

Cleaning by hand

Make sure the oven is cool before cleaning.

● The catalytic enameled cover casing should be cleaned using a solution of hot water and washing-up liquid applied with a soft nylon brush.

Do not use abrasive cleaning agents, hard brushes, scouring pads or cloths, steel wool, knives or other abrasive materials. Do not use oven spray on catalytic enamel as the chemicals used in oven sprays will damage catalytic enamel and render it ineffective.

If using oven sprays on the interior oven surfaces, Please spray it taking care to not spray the catalytic enamel cover casing.

Cleaning with high temperatures

Before cleaning the catalytic cover casing with high temperatures, make sure that all interior oven surfaces have been cleaned as described above. Otherwise, the high temperatures can bake deposits onto the interior oven surfaces and make them impossible to remove.

If, after manual cleaning, the oven is still heavily soiled, heating it to a high temperature will help remove soiling caused by oil and grease splashes.

Note that deposits of spices, syrups and similar substances are not removed by this process.

These should be removed by hand with a mild solution of hot water and washing-up liquid applied with a soft brush.

● Remove all accessories from the oven.

● Set the oven to conventional function.

● Set the heat to 250 °C.

● Run the oven for approximately 1 hour. The length of time will depend on the degree of soiling.

It is a good idea to set the finish time for the process using the end time setting, in case you forget to switch the oven off at the end.

Any remaining soil will gradually disappear with each subsequent use of the oven at high temperatures.

34

BF665CCST_HAC-00091V_EN.indd 34 2007-06-07 ｿﾀﾀ・9:16:11

Cleaning and Care (Continued)

Cleaning the oven door

For normal use, the oven door should not be removed but if removal is necessary, for example, for cleaning, follow these instructions. The oven door is heavy.

Removing the door

1. Flip open the clips at both hinges.

EN

2. With both hands, grasp the sides of the oven door at its middle.

3. Rotate the door by approximately 70 ° until the hinges can be taken out completely from the hinge holes.

2

70

1

35

BF665CCST_HAC-00091V_EN.indd 35 2007-06-07 ｿﾀﾀ・9:16:28

EN

Cleaning and Care (Continued)

Attaching the door

1. With the clips still flipped open, align the door hinges into the hinge holes.

70

2. Rotate the door toward the horizontal line and flip the clips closed.

The hinge is normally inserted.

Hinge

Hinge hole

BF665CCST_HAC-00091V_EN.indd 36

36

2007-06-07 ｿﾀﾀ・9:17:01

Cleaning and Care (Continued)

Oven door glass

The oven door is equipped with three sheets of glass placed against each other. The inner & middle sheets can be removed for cleaning.

WARNING

● Whenever the door is separated from the oven, the clips should be flipped open.

● Do not use harsh abrasive cleaners or metal scrapers to clean the oven door; they ca scratch the surface, which may cause the glass to shatter.

● When the door is mounted, removing some of the parts (the door glass or some other part)

from the door may result in injury.

Attention

The glass may break if you use excessive force especially at the edges of the front sheet.

Disassembling the door

1. Remove the two screws on the left and right sides of the door.

2. Remove the two supports and the door bracket and remove the two screws attaching the handle.

Glass #1

EN

Door bracket

Glass #3

3. Detach the inner sheet, glass #1, from the door.

4. Lift glass #2 and remove the two spring-brackets from the top of the sheet.

Door bracket

Holder glass inner

Spring bracket

(Right and Left)

Glass #1

Glass #2

Glass #3

Glass #2

 Clean the sheets with warm water or washing-up liquid and polish dry with a soft clean cloth.

37

BF665CCST_HAC-00091V_EN.indd 37 2007-06-07 ｿﾀﾀ・9:17:51

EN

Cleaning and Care (Continued)

Assembling the door

1. Clean the glass and interior parts with warm soapy water.

 Do not use abrasive cleaners or pan scourers. Use a sponge with liquid detergent or warm soapy water.

2. Attach the two spring brackets at the top of glass #2 and place glass #2 into position.

3. Attach glass #1, the door bracket and the supports to the door.

4. Secure the two screws at both sides of the door.

Side Runners

To clean the interior of the oven, the both side runners can be removed.

Detaching the Side Runners

1. Turn the screw at the back 2-3 times anti-clockwise only.

BF665CCST_HAC-00091V_EN.indd 38

38

2007-06-07 ｿﾀﾀ・9:17:52

Cleaning and Care (Continued)

2. Remove the screw at the front by turning it anti-clockwise after latching the side runner.

3. Pull and remove the side runner.

4. Remove the screw from the back by turning it anti-clockwise.

EN

BF665CCST_HAC-00091V_EN.indd 39

39

2007-06-07 ｿﾀﾀ・9:17:53

EN

Cleaning and Care (Continued)

Attaching the Side Runners

1. Insert the screw at the back and turn it clockwise 2-3 times only.

2. Insert and push the back U-form of the side runner towards the screw.

3. Insert the screw at the front, and fasten both screws.

BF665CCST_HAC-00091V_EN.indd 40

40

2007-06-07 ｿﾀﾀ・9:17:55

Cleaning and Care (Continued)

Cleaning the top heater

1. Remove the upper nut circular by turning it anti-clockwise while holding the top of the heater.

The front of the top heater inclines downwards.

2. When cleaning has been done, lift the top of the heater back to its original level and turn the nut circular clockwise.

EN

BF665CCST_HAC-00091V_EN.indd 41

41

2007-06-07 ｿﾀﾀ・9:17:56

EN

Cleaning and Care (Continued)

Changing the lamp

 Danger of electric shock!

Before replacing the oven light bulb, take the following steps:

● Switch off the oven;

● Disconnect the oven from the mains supply; and

● Protect the oven light bulb and the glass cap by laying a cloth on the bottom of the oven.

 You can buy a lamp at SAMSUNG service centre.

Replacing the rear oven lamp and cleaning the glass cap

1. Take off the cap by turning counterclockwise.

2. Remove the metal ring and the sheet ring and clean the glass cap.

3. If necessary, replace the bulb with a 25 watt, 230 V, 300 °C heat

- resistant oven light bulb.

4. Fit the metal and the sheet ring to the glass cap.

5. Replace the glass cap.

BF665CCST_HAC-00091V_EN.indd 42

42

2007-06-07 ｿﾀﾀ・9:17:57