Installation and Cabling. Dukane P42

00u24121UE 01.9.21 9:59 AM ページ 6

INSTALLATION INSTRUCTIONS (continued)

Installation and Cabling

Connecting to a PC

■ Read SAFETY GUIDELINES ( to ) carefully to ensure maximum safety before proceeding to these steps:

I VII

1) Make sure that the display signals produced by your PC meet the specifications of this product.

2) Choose an appropriate site and install the product on a level table where the stand is secure.

• Install the monitor to have ready access to a power socket available.

3) Make sure that your PC’s power switch is off.

4) Interconnect the signal input terminal (RGB1) on the monitor rear panel and the display signal output terminal of the PC to each other using the signal cable included.

• Optional cables are needed to connect to the RGB2 input and audio input terminals.

• If the signal cable included does not match your PC, consult your dealer after reading the section “Signal Input”.

28

5) Insert one end of the power cable included into the rear-panel power cable connector and the other end into a power socket.

6) Turn on the monitor, then the PC to make sure that a display image appears on the monitor screen.

• For instructions on turning on the monitor and adjusting its display images, see

Monitor rear panel

Speaker (R) Speaker (L)

6

Power cable

Power cable connector

RGB 1

D-SUB IN RGB 2

V H B G R

AUDIO IN

3.5mm

Stereo mini jack

To signal input terminals

To signal input terminals

To signal output terminal

To signal output terminal

PC

To audio output terminal

Cord Clamper

When connecting a computer audio input to the unit (using a 3.5mm stereo mini jack), the cord must pass through the cord clamp toward the bottom of the back of the main unit. If it does not, there is a possibility of insufficient suppression of electromagnetic radiation.

00u24121UE 01.9.20 1:41 PM ページ 7

Connecting to Video Equipment

(such as a Laser Disc player, a DVD player, a DSS,or a Video Camera)

■ Read SAFETY GUIDELINES ( to ) carefully to ensure maximum safety before proceeding to these steps:

I VII

1) Choose an appropriate site and install the product on a level table where the stand is secure.

• Install the monitor to have ready access to a power socket available.

2) Make sure that the video equipment’s power switch is off.

3) Interconnect the signal input terminal on the monitor rear panel and the video equipment’s signal output terminal to each other using an commercially available video cable.

4) Insert one end of the power cable included into the rear-panel power cable connector and the other end into a power socket.

5) Turn on the monitor, then the video equipment’s to make sure that a display image appears on the monitor screen.

• For instructions on turning on the monitor and adjusting its display images, see

Monitor rear panel

Speaker (R) Speaker (L)

External Monitor

Video equipment

(such as a video disc player, a DVD player, and a video camera)

Power cable connector

Power cable

AUDIO IN

R L/MONO

AUDIO IN

R L/MONO

VIDEO 2

COMPONENT

P

R

/C

R

P

B

/C

B

Y

VIDEO 1

COMPOSITE S

IN OUT IN

VIDEO 1

COMPOSITE S

IN OUT IN

To component

input terminals

To audio/ video input terminals

To component

input terminals

Use if the video equipment has an

S video input terminal

• If video equipment with an S video output terminal is used, cabling by the S video cable is recommended to provide finer video quality. (If an S video input terminal and a video input terminal connect to the monitor at the same time, S video input would govern.)

• If video equipment is equipped with component video output (Y, P

B,

P

R or Y, C

B,

C

R

), please connect to the corresponding color (Y, P

B,

P

R

) input jack on the component input of the monitor.

• If the VIDEO1 OUT terminal is connected to an external monitor with a 75 Ohm terminal, it is possible to view the same image as on the main unit. If an external monitor is not being used, the cable must be removed from the VIDEO OUT terminal. The image will appear white as saturation level is reached.

NOTE : Y to Y, P

B

-C

B to P

B

, P

R

-C

R to P

R

.

7