- No category
advertisement
VAR8-ACU and Variants - Operation, Commissioning, Fault Finding, and Maintenance Guide
26 Manual Restoration of Default Settings
It is possible to restore all default settings, including the access code, by setting DIP-switches to a special power-up condition.
DIP Switch
26.1 Restoring Access Code
1. Power down the unit by disconnecting the 24 V DC power supply.
2. Set DIP Switch-3 to ON.
3. Power on with the above settings selected to clear the access code in the non-volatile memory and restore the default settings of ‘0999’.
This will only take a couple of seconds. The VAR8-ACU display indicates when this process is complete.
4. Power off and restore the settings for normal operation.
26.2 Restoring All Defaults
1. Power down the unit by disconnecting the 24 V DC power supply.
2. Set DIP Switch-4 to ON.
3. Power on with the above setting selected to clear the whole configuration in the non-volatile memory and restore the default settings as shown below.
This will only take a couple of seconds. The VAR8-ACU display indicates when this process is complete.
4. Power off and restore the settings for normal operation.
Issue: 02 complete, approved
Page 130 of 138
VAR8-ACU and Variants - Operation, Commissioning, Fault Finding, and Maintenance Guide
Access code
Setting
Report over-temperature
Maximum temperature
Default Value
0999
No
70 °C
Input Type
Input Gain
Input Surv
Input Surv Sensitivity
EQ
Unused
Inputs 1, 3, and 4 = Network Channel
−20 dB
Off
−40
0 dB All bands, HPF=Off
Fades 00
Chime Type Off
Chime Level
Output Gains
−12 dB
0 dB
Name
Output Level
Surveillance Mode
Level
Override Gain
DVA Modes
Busy Indication
Fault Contacts
As input number
0 dB
Continuous ‘On’
−9 dB
−30 dB
DVA Full
On
Not-config
Issue: 02 complete, approved
Page 131 of 138
advertisement
Related manuals
advertisement
Table of contents
- 7 Introduction
- 7 Important Notes
- 8 Equipment Requirement
- 8 SW Versions
- 9 Configuration Safety Checklist
- 10 Control and Indicators
- 12 User Interface Description
- 12 Accessing the User Interface
- 12 Navigating the Menus
- 12 Menu Selection Markers
- 13 Selecting Menu Item and Saving Changes
- 13 Changing an Option
- 13 Rotary Encoder
- 13 LCD Display Timeouts
- 14 Menu Map of Functions
- 15 VAR8-ACU Commissioning Procedure
- 17 Access to the System
- 17 Logging On
- 17 Logging Off
- 18 Network Operation Setup
- 18 Network Topology
- 18 System Parameters
- 18 Main Network Features
- 20 Audio Control Unit Configuration
- 20 Audio Control Unit Specific Configuration
- 22 Defining a Slave Unit within the Network
- 24 Defining a Slave Unit’s Network Outputs
- 26 Local Input Configuration
- 27 Input Type and Name Configuration
- 28 Input Emergency Class Configuration
- 29 Microphone Parameters Configuration
- 30 Audio Parameter Configuration
- 33 Priority Set-up
- 35 Microphone Button Configuration
- 35 Paging or Zoneable Fire Microphone Button Configuration
- 36 Unused Buttons
- 37 Microphone Routing or Zone Select Button
- 39 Play DVA Button
- 42 All Call Button
- 44 Cancel All DVAs Button
- 46 Single Button Microphone Button Configuration
- 47 Listen-in Configuration
- 49 Unused Audio Inputs
- 50 DVA Input Configuration
- 50 DVA Input Name Configuration
- 51 DVA Input Emergency Class Configuration
- 52 Audio Parameter Configuration
- 52 Priority Set-up
- 54 Music Input Configuration
- 54 Input Type and Name Configuration
- 55 Music Input Emergency Class Configuration
- 55 Audio Parameter Configuration
- 58 Priority Set-up
- 60 Mute Input Configuration
- 60 Mute Input Emergency Class Configuration
- 61 Priority Set-up
- 62 Output Configuration
- 64 Permanent Route Configuration
- 65 Remote I/O Unit Configuration
- 65 Remote I/O Unit Connected to the RS485 Port
- 67 Remote I/O Unit Connected to a Mic/Line Input
- 69 DVA or Route Triggers via Contact Configuration
- 70 DVA or Route Trigger via Router Digital Input (Contact)
- 73 DVA or Route Trigger via Remote I/O Unit Digital Input (Contact)
- 77 DVA Resetting via Contact Configuration
- 77 DVA Resetting via Router Digital Input (Contact)
- 79 DVA Resetting via Remote I/O Unit Digital Input (Contact)
- 81 External Fault Configuration
- 81 Router Digital Input as External Fault
- 83 Remote I/O Unit Digital Input as External Fault
- 85 Remote I/O Unit Analogue Input as External Fault
- 87 Fault Indication Configuration
- 89 System Configuration
- 89 Changing the System Access Code
- 89 System Date and Time
- 89 System Name
- 90 Emergency Sounder Operation
- 90 Host Routing Timeout Configuration
- 90 Temperature
- 91 Clearing Configuration Data and Restoring the Default Settings
- 91 System Software Versions
- 92 Communication Port Configuration
- 92 RS232 Asynchronous Port Configuration
- 93 RS485 Port Configuration
- 94 Establishing and Testing Network Connection
- 95 Network Faults – Recovery and Diagnosis
- 95 Normal Data Network Operation
- 95 Data Network Operation with Fault
- 96 Normal Audio Network Operation
- 96 Audio Network Operation with Fault
- 97 Diagnostic Tools and Methods
- 97 Network Faults
- 97 Hardware
- 97 Software
- 97 Current Status of the Health Status of the Network
- 98 Audio Loop Failure
- 98 Data Loop Failure
- 99 Polling Control
- 99 All Call Mode Control
- 99 Other Testing Facilities
- 99 Viewing the Routing Status
- 100 Viewing the Contact Status
- 100 Audio Monitoring
- 100 Sounder and Lamp Test
- 101 PC Configuration Tool
- 101 Connection
- 101 Starting a New Configuration
- 101 Loading the Configuration from the Unit
- 102 Loading the Configuration from a File
- 102 Saving the Configuration as Text File
- 102 Applying Changes to the Unit
- 103 VAR8-ACU User Interface Menu
- 105 VAR8-ACU Menu Description
- 118 Fault Indication and Fault Finding
- 118 Fault Indication
- 119 Current Fault Status
- 119 Viewing Slave Active Faults at the Audio Control Unit
- 119 Viewing Audio Control Unit Active Faults
- 120 Fault Acceptance
- 120 Accepting Slave Faults at the Audio Control Unit
- 120 Accepting Audio Control Unit Faults
- 121 Fault Clearance
- 121 Clearing Slave Faults at the Audio Control Unit
- 121 Clearing Audio Control Unit Faults
- 122 Fault Log View
- 122 Viewing the Fault Log at the Audio Control Unit
- 122 Viewing the Audio Control Unit Fault Log
- 122 Viewing a Slave Unit Fault Log at the Audio Control Unit
- 122 Clearing the Fault Log
- 123 System Fault Finding Guide
- 123 General Faults
- 125 Faults Reported Specific to the Audio Control Unit
- 125 Numeric Fault Codes and Their Meaning
- 126 Maintenance
- 126 Training
- 126 Records
- 127 Maintenance Instructions
- 127 Routine Maintenance
- 127 Daily Attention
- 127 Weekly Attention
- 127 Monthly Attention
- 127 Quarterly Inspection and Test
- 127 Annual Inspection and Test
- 128 Replacement of the Real Time Clock Battery
- 129 Corrective Maintenance
- 129 Action by the User after Any Fire (Whether Detected Automatically or Not)
- 129 Action Following a Fault
- 130 Manual Restoration of Default Settings
- 130 Restoring Access Code
- 130 Restoring All Defaults
- 131 Default Settings
- 132 Safety and Precautions
- 132 Environmental
- 132 ESD
- 132 EMC
- 132 Electrical Safety
- 132 Lithium Battery
- 132 Unpacking and Handling
- 132 Packing for Repair
- 133 Reference Documents
- 134 Index