advertisement
Changing Needles
CAUTION
Please make sure the power to the machine is turned off before carrying out the following operations. There is a chance of injury if the machine accidentally starts running during this operation.
Changing the Needle
Raise needle to highest position using handwheel, and lower presser foot.
2 and remove needle.
3 side to the right, and insert the needle as far as it will go. Make sure needle is securely set in the needle chamber by screwing in tightly.
Screwdriver
✽
✽
If the needle is not adequately inserted or the screw is loose, this may break the needle or cause a breakdown and the needle threader will not work.
Check needles on a flat surface to make sure they are not bent.
The needle should lay parallel to a surface.
Flat surface
Lay needle on a flat surface
(such as the needle plate or a plate of glass).
Note
• HLX5 needles should be used; however, Schmetz 130/705H may also be used under normal circumstances.
Changing the Feed Pin
position. (See page 10.)
2 and needle plate.
3 handwheel until feed pin is in its highest position.
Insert small screwdriver
(included) as shown in diagram.
While holding spring with fingertip, lower the feed pin changer onto the needle to pick it up.
changer, lower and attach while holding spring with fingertip.
Remove screwdriver.
8 and presser foot.
11
advertisement
Related manuals
advertisement
Table of contents
- 3 INTRODUCTION
- 3 IMPORTANT SAFETY INSTRUCTIONS
- 8 Accessories
- 9 Machine Features
- 10 Before You Begin (1)
- 10 Power Cord and Foot Controller
- 10 Main Power Switch
- 10 Thread Tension Dial
- 10 Handwheel
- 10 Stitch Length Regulator
- 10 Reverse Stitch Lever
- 11 Presser Foot Lever
- 11 Knee Lifter
- 11 Presser Foot Pressure Adjustment Dial
- 11 Fabric Extension Table
- 12 Before You Begin (2)
- 12 Thread Cutter Button
- 12 Needle Stop Position Button
- 12 Feed Dog Adjustment Knob
- 13 Changing Needles
- 13 Changing the Needle
- 13 Changing the Feed Pin
- 14 Threading (1)
- 14 Bobbin Winding
- 16 Bobbin Installation
- 17 Threading (2)
- 17 Upper Threading
- 18 Using the Automatic Needle Threader
- 18 Using the Spool Net
- 19 Stitch Samples and Needle Chart
- 19 Stitch Samples
- 19 Thread Tension
- 20 Changing Presser Feet
- 20 Changing Presser Feet (Zipper Foot)
- 20 Presser Feet
- 21 Basic Sewing (1)
- 21 Basic Sewing
- 21 Pin Feeding (for hard-to-handle fabrics)
- 22 Basic Sewing (2)
- 22 Rolled Hem Foot
- 23 Basic Sewing (3)
- 23 Zipper Foot
- 24 Invisible Zipper Foot
- 24 1/4” Foot
- 25 Free Motion Quilting Foot
- 25 Walking Foot
- 26 Seam Guide
- 27 Caring for Your Machine
- 27 Cleaning the Machine
- 27 Lubrication Points
- 28 Trouble Shooting
- 30 INTRODUCTION
- 30 INSTRUCTIONS DE SÉCURITÉ IMPORTANTES
- 35 Accessoires
- 36 Fonctions de la machine
- 37 Avant de commencer (1)
- 37 Cordon d’alimentation et pédale
- 37 Interrupteur d’alimentation principal
- 37 Disque sélecteur de tension du fil
- 37 Molette
- 37 Sélecteur de longueur de point
- 37 Levier de point arrière
- 38 Levier du pied-de-biche
- 38 Levier au genou
- 38 du pied-de-biche
- 38 Table de rallonge pour tissu
- 39 Avant de commencer (2)
- 39 Bouton de ciseaux
- 39 Bouton de position d’arrêt d’aiguille
- 39 Bouton de réglage des griffes d’entraînement
- 40 Remplacement de l’aiguille
- 40 Remplacement de l’ergot d’entraînement
- 41 Enfilage (1)
- 41 Remplissage de la canette
- 43 Installation de la canette
- 44 Enfilage (2)
- 44 Mise en place du fil supérieur
- 45 Utilisation de l’enfileur automatique
- 45 Utilisation du filet de la bobine
- 46 Points d’essai et tableau d’aiguilles
- 46 Points d’essai
- 46 Tension des fils
- 47 Changement du pied-de-biche
- 47 (Pied pour fermeture à glissière)
- 47 Les différents pieds-de-biche
- 48 Couture de base (1)
- 48 Couture de base
- 48 (pour les tissus difficiles à manipuler)
- 49 Couture de base (2)
- 49 Pied pour ourlet rouleauté
- 50 Couture de base (3)
- 50 Pied pour fermeture à glissière
- 51 Pied pour fermeture à glissière invisible
- 52 à mouvement libre
- 52 Pied à double entraînement
- 53 Guide de couture
- 54 Entretien de la machine à coudre
- 54 Nettoyage de la machine
- 54 Points de graissage
- 55 Dépannage