advertisement
4.3
Startup
State
Page 21
When power is applied, the flowmeter enters the Startup state. In the Startup State, the flowmeter waits for up to 7 seconds for the Setup button to be pressed at which time the
Setup mode is entered and changes to the configuration can be made. If the setup button is not pressed, the flowmeter will enter the Run Mode and attempt to start flow measurement. If the transducers are not installed on the pipe, a fault will occur. The location of the Setup button is as follows:
Model 1:
a push-button switch on the controller motherboard.
SETUP BUTTON (white)
Model 2:
Model 3:
as for Model 1.
as for Model 2, plus a SETUP soft button appears on the display.
TRANSDUCER
INPUTS
Tx 1 Tx 2
INDICATOR
LIGHTS
SETUP BUTTON
SIGNAL
OUTPUTS mA Hz
FUSE
1A 250V (5 x 20)
POWER INPUT
DC AC
T D
MODE SWITCH
SD CARD
DATA LOG
(REMOVE)
RS485
RS232
USB ETHERNET
COMMUNICATIONS
CONNECTOR PANEL
COM
NC
NO
COM
NC
NO
COM
NC
NO
R1
R2
R3
PROCESS CONTROL RELAYS
(THREE EACH) 10A 250V AC
CIRCUIT BOARD LAYOUT
WARNING
INPUT POWER
LIMITS
AC INPUT
96VAC - 264VAC
50/60 Hz
DC INPUT
15 to 30 VDC
CAUTION risk of electric shock
The flowmeter indicates that it is in the Startup State as follows:
Model 1:
the Fault (red) LED is OFF and all yellow LEDs are at first ON and then turn OFF one by one, starting at LED1, at intervals of 1.5 seconds, so as to count down the 7 second pause.
Model 2:
as for Model 1, plus the display screen indicates:
Startup ...
Tap Setup to enter Setup Mode
Hold Setup for Zero Calibration
Configuration set #
(Searching for SD Card)
Below this, a “progress bar” counts off the 7 second delay.
Model 3:
as for Model 2, plus the SETUP soft button is available.
MODEL 1
Information Screen
Firmware Version, A01.00.00
Startup …
Tap Setup to enter Setup
Hold Setup for Zero Calibration
Configuration Set #1
(Searching for SD Card)
[
£
]
MODEL 2
Information Screen
Firmware Version, A01.00.00
Startup …
Tap Setup to enter Setup
Hold Setup for Zero Calibration
Configuration Set #1
(Searching for SD Card)
[ ]
SETUP
MODEL 3
Ultrasonic Flowmeter
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 5 Operating principles
- 5 Transit Time operation
- 6 Doppler operation
- 7 Fluid requirements
- 7 Pipe requirements
- 7 Straight pipe length requirements
- 8 Standard model features and options
- 9 Wiring compartment
- 16 Unpacking
- 16 Select a mounting location
- 16 Wall mounting
- 17 Panel mounting
- 17 Pipe mounting
- 18 Select a measurement method
- 18 Electrical connections
- 19 Cable gland liquid tight connections
- 21 Power on and self test
- 21 Description of operating states and controls
- 22 Startup state
- 22 Setup (configuration) mode
- 23 Transducer positioning state
- 24 Zero calibration state
- 25 Run mode
- 25 Fault and warning codes
- 27 Menu Navigation
- 27 Setup root menu
- 27 Escaping from setup
- 28 Global configurations
- 28 Communication settings
- 29 Master password
- 29 Setting the date and time
- 29 Saving changes
- 30 Manage configuration sets
- 30 Activate a configuration set
- 30 Open a saved configuration set
- 30 Create a new configuration set
- 30 Delete a saved configuration set
- 31 Configuration edit menu
- 31 Editing data items
- 31 5.4.1.1 . Editing numerical values
- 32 5.4.1.2 . Entering passwords using the soft buttons
- 32 5.4.1.3 . Units of measure
- 33 Transducer setup
- 34 Metering setup
- 37 Process control setup
- 39 Reset working set to factory values
- 39 Set password (for a single configuration set)
- 39 Saving changes
- 39 Escape without saving
- 40 Transducer piping system location
- 40 Transducer mounting mode for Doppler measurement
- 40 Transducer mounting mode for Transit Time measurement
- 41 Transducer separation distance
- 42 Pipe surface preparation
- 42 Doppler method transducer installation
- 43 Transit Time transducer installation - V and W mount mode
- 44 Transit Time transducer installation - Z mount mode
- 46 Transducer acoustic mounting gaskets
- 47 Transducer pipe mounting clamps
- 48 Primary and secondary display areas
- 49 Flow rate measurement
- 50 Total flow measurement
- 50 Measurement status areas
- 50 Configuration and mode
- 50 Goodness of measurement
- 51 Sound speed display
- 51 Measuring the fluid sound speed
- 52 Process control status areas
- 52 Analog signal output
- 53 Digital pulse output
- 53 Logging rate setpoints
- 53 Logging totalizer setpoints
- 54 Local log data storage (SD flash memory card)
- 54 7.6.4.1 . Inserting and removing the memory card
- 54 7.6.4.2 . Format of data on the memory card
- 54 7.6.4.3 . Rotation and purging of log files
- 55 7.6.4.4 . Power loss
- 55 Remote access to log data
- 57 Manual batch start type
- 58 Auto batch start type
- 60 Flow rate alarms
- 62 More on clearing alarm conditions
- 63 Software installation
- 63 Making connections
- 63 Ethernet Connection
- 64 Serial and USB connections
- 64 Retrieving log data
- 66 Complete flowmeter model number system
- 66 Additional transducers model number system
- 67 Specifications
- 68 Pipe dimensional data
- 70 Sound speed data
- 71 Troubleshooting guide