- Computers & electronics
- Audio & home theatre
- Supplementary music equipment
- AMX
- CWU-SAA596807
- User manual
advertisement
Installing Tabletop (MXT) Panels
MXT-1001 / MXT-701
Detailed specifications drawings for the MXT-1001 and M XT-701 are available to download from www.amx.com.
Connector Locations - MXT-1001/MXT-701
Two Type A USB ports are located on the rear right corner of the panel (FIG. 17). USB peripherals (i.e. mouse, keyboard) may be connected to either of the two USB ports on the rear of the device. Updates to the device’s firmware can also made via the USB ports (see the Modero G5 Configuration and Programming Guide for details). Note that FIG. 17 shows the MXT-1001, but the USB ports are in a similar location on the MXT-701.
USB Ports Entry for RJ45/PoE Cable
FIG. 17 MXT-1001 - rear view
NOTE:
Refer to the Power via PoE section on page 32
for details on PoE and Ethernet Cable Installation and Modification.
Power via 13.5V
The MXT-2001-PAN and MXT-1901-PAN use a 13.5V -compliant power supply to provide power to the panel via the 2-pin 3.5mm captive wire PWR connector. The incoming PWR and GND wires from the power supply must be connected to the corresponding locations within the PWR connector.
NOTE: Connecting power to the panel should be done using the included 2-pin 3.5mm captive wire connector included with the device. This connector is retained within its port with locking screws instead of the pins on each side of standard captive wire connectors, and using force to insert a standard captive wire connector may damage the device.
Wiring a 13.5V
Power Connection
To use the 2-pin 3.5mm captive wire connector with a 13.5V
-compliant power supply, the incoming PWR and GND wires from the external source must be connected to their corresponding locations on the connector (FIG. 18). The connector uses locking screws to insure a connection to the device, so make sure to insert and tighten the screws before applying power.
PWR +
Power Supply
GND -
To the Touch Panel
FIG. 18 NetLinx power connector wiring diagram
1.
Insert the PWR and GND wires on the terminal end of the 2-pin 3.5mm captive wire cable.
Match the wiring locations of the +/- on both the power supply and the terminal connector.
2.
Tighten the clamp to secure the two wires.
Do not tighten the screws excessively; doing so may strip the threads and damage the connector.
3.
Verify the connection of the 2-pin 3.5mm captive wire to the external 13.5V
-compliant power supply and apply power.
Power via PoE
Power for the MXT-1001 and MXT-701 is supplied via PoE (Power Over Ethernet), utilizing an AMX-certified, capacitive touchcompliant PoE injector such as the PS-POE-AT High Power PoE Injector ( FG423-81 ) or other approved AMX PoE power source.
The incoming Ethernet cable should be connected to the RJ45 port on the cable attached to the device.
Modero X® Series G5 Touch Panels - installation & Hardware Reference Manual 32
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 7 Modero X Series G5 Touch Panels
- 7 Overview
- 8 Sleep Button
- 8 Powering On/Off X Series G5 Panels
- 8 Configuration and Programming
- 8 Bluetooth Support
- 9 NFC Support
- 9 Active Video Windows - Limitations
- 9 Cleaning the Touch Overlay and Case
- 10 Additional Documentation
- 11 MXT/D-2001-PAN - 20.3" X Series G5 Panels
- 11 MXT-2001-PAN (Tabletop)
- 11 MXT-2001-PAN Specifications
- 13 MXD-2001-PAN (Wall-Mount - Landscape/Portrait)
- 13 MXD-2001-PAN Specifications
- 16 MXT/D-1901-PAN - 19.4" X Series G5 Panels
- 16 MXT-1901-PAN (Tabletop)
- 16 MXT-1901-PAN Specifications
- 18 MXD-1901-PAN (Wall-Mount - Landscape/Portrait)
- 18 MXD-1901-PAN Specifications
- 21 MXT/D-1001 - 10.1" X Series G5 Panels
- 21 MXT-1001 (Tabletop)
- 21 MXT-1001 Specifications
- 23 Touch Panel Aspect Ratio
- 23 MXD-1001 (Wall-Mount - Landscape/Portrait)
- 23 MXD-1001 Specifications
- 25 Touch Panel Aspect Ratio
- 26 MXT/D-701 - 7" X Series G5 Panels
- 26 MXT-701 (Tabletop)
- 26 MXT-701 Specifications
- 27 Touch Panel Aspect Ratio
- 28 MXD-701 (Wall-Mount - Landscape/Portrait)
- 28 MXD-701 Specifications
- 30 Touch Panel Aspect Ratio
- 31 Installing Tabletop (MXT) Panels
- 31 MXT-2001-PAN / MXT-1901-PAN
- 31 Connector Locations - MXT-2001-PAN / MXT-1901-PAN
- 32 MXT-1001 / MXT
- 32 Connector Locations - MXT-1001/MXT
- 32 Wiring a 13.5V Power Connection
- 32 Power via PoE
- 33 Ethernet Cable Installation and Modification
- 34 Installing Wall-Mount (MXD) Panels
- 34 A Note About Wall and Rack Installation
- 35 Installation Recommendations
- 35 MXD-2001-PAN / MXD-1901-PAN Installation
- 35 Installing the MXD-2001-PAN / MXD-1901-PAN Into a Wall
- 36 MXD-2001-PAN Dimensions
- 37 MXD-1901-PAN Dimensions
- 38 Installing the Backbox
- 38 MXD-2001-PAN Installation Dimensions
- 39 MXD-1901-PAN Installation Dimensions
- 42 Wiring a 13.5V Power Connection
- 42 Uninstalling the MXD-2001-PAN / MXT-1901-PAN
- 42 Removing the Panel From Its Backbox
- 43 MXD-1001 / MXD-701 Installation
- 43 Installing the MXD-1001 / MXD-701 Into a Wall
- 44 MXD-1001 Dimensions
- 45 MXD-701 Dimensions
- 46 Installing the Backbox
- 46 MXD-1001 Installation Dimensions
- 47 MXD-701 Installation Dimensions
- 50 Power via PoE
- 50 Ethernet Cable Installation and Modification
- 51 Uninstalling the MXD
- 51 Removing the MXD-1001 From Its Backbox
- 52 Uninstalling the MXD
- 52 Removing the MXD-701 From Its Backbox
- 53 Appendix: Troubleshooting
- 53 Overview
- 53 Panel Doesn’t Respond To Touches
- 53 Panel Isn’t Appearing In The Online Tree Tab
- 53 Can’t Connect To a NetLinx Master
- 53 Only One Modero Panel In My System Shows Up