Connectors. Handheld Group AB YY3-ALGIZ10XB

Add to My manuals
41 Pages

advertisement

Connectors. Handheld Group AB YY3-ALGIZ10XB | Manualzz

Algiz 10XB Manual

 

Use   only   detergents   or   cleaners   intended   for   computers.

   

Connectors

1.

  Remove   the   battery  

2.

  Soak   the   end   of   a   swab   with   isopropyl   alcohol   and   rub   across   the   connector   pins.

   

3.

  Be   careful   not   to   leave   any   residue   on   the   connectors.

 

4.

  This   process   should   be   repeated   approximately   three   times.

 

 

Note:   If   isopropyl   alcohol   is   not   available,   use   computer   cleaning   detergent   or   a   pencil   eraser  

(rubber),   taking   care   not   to   leave   any   foreign   bodies   on   the   pins.

   

Copyright Notice

Copyright   ©   2010   Handheld   Group   AB,   ALL   RIGHTS   RESERVED.

  No   part   of   this   document   may   be   reproduced,   copied,   translated   or   transmitted   in   any   form   or   by   any   means,   electronic   or   mechanical,  

  for   any   purpose,   without   the   prior   written   permission   of   the   original   manufacturer.

 

Trademark Acknowledgement

 

Brand   and   product   names   are   trademarks   or   registered   trademarks   of   their   respective   owners.

 

Disclaimer

Handheld   Group   AB   reserves   the   right   to   make   any   product   changes   without   notice,   including   to   circuits   and/or   software   described   or   contained   in   this   manual,   in   order   to   improve   design   and/or   performance.

  Handheld   Group   AB   assumes   no   responsibility   or   liability   for   the   use   of   the   described   product(s),   conveys   no   license   or   title   under   any   patent,   copyright,   or   mask   works   rights   to   these   products   and   makes   no   representations   or   warranties   that   these   products   are   free   from   patent,   copyright,   or   mask   works   rights   infringement,   unless   otherwise   specified.

  Applications   described   in   this   manual   are   for   illustration   purposes   only.

  Handheld   Group   AB   makes   no   representation   or   warranty   that   such   applications   will   be   suitable   for   the   specified   use   without   further   testing   or  

  modification.

 

Customer Service

38 handheld

Algiz 10XB Manual

 

Support   is   provided   by   Handheld.

  Visit   our   website   at   www.handheldgroup.com

  to   find   updated  

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

  information   about   the   product.

  You   can   also   contact   your   distributor,   sales   representative   or   our   customer   support   center   for   further   assistance.

  If   you   contact   our   customer   support   center   please   have   the   following   information   ready   before   you   call:  

Product   serial   number    

Peripheral   attachments    

Software   (OS,   version,   application   software,   etc.)    

Description   of   complete   problem  

The   exact   wording   of   any   error   messages   with   print   screen   images  

 

In   addition   to   this,   free   technical   support   is   available   from   our   engineers   during   working   hours.

  We   are   always   ready   to   provide   advice   on   application   requirements   or   specific   information   about   the   installation   and   operation   of   any   of   our   products.

  Please   do   not   hesitate   to   call   or   e ‐ mail   us.

 

 

Manufacturer:   Handheld   Group   AB    

Address:   Handheld   Group   AB,   Kinnegatan   17   A,   SE ‐ 531   33,   Lidköping,   Sweden          

TEL:   +46   (0)   510 ‐ 54   71   70     FAX:   +46   (0)   510 ‐ 282   05  

39 handheld

Algiz 10XB Manual

 

FCC     Warning  

This   equipment   has   been   tested   and   found   to   comply   with   the   limits   for   a   Class   B   digital   device,   pursuant   to   Part   15   of   the   FCC   Rules.

  These   limits   are   designed   to   provide   reasonable   protection   against   harmful   interference   in   a   residential   installation.

  This   equipment   generates,   uses   and   can   radiate   radio   frequency   energy   and,   if   not   installed   and   used   in   accordance   with   the   instructions,   may   cause   harmful   interference   to   radio   communications.

    However,   there   is   no   guarantee   that   interference   will   not   occur   in   a   particular   installation.

  If   this   equipment   does   cause   harmful   interference   to   radio   or   television   reception,   which   can   be   determined   by   turning   the   equipment   off   and   on,   the   user   is   encouraged   to   try   to   correct   the   interference   by   one   of   the   following   measures:    

‐    Reorient   or   relocate   the   receiving   antenna.

 

  ‐    Increase   the   separation   between   the   equipment   and   receiver.

 

  ‐    Connect   the   equipment   into   an   outlet   on   a   circuit   different   from   that   to   which   the   receiver   is   connected.

 

 

  ‐    Consult   the   dealer   or   an   experienced   radio/TV   technician   for   help.

 

Any   changes   or   modifications   not   expressly   approved   by   the   party   responsible   for   compliance   could   void   the   user's   authority   to   operate   this   equipment.

 

 

 

 

 

 

 

This   device   complies   with   Part   15   of   the   FCC   Rules.

  Operation   is   subject   to   the   following   two   conditions:     (1)   This   device   may   not   cause   harmful   interference,   and   (2)   This   device   must   accept   any   interference   received,   including   interference   that   may   cause   undesired   operation  

 

 

Exposure   to   radio   frequency   (RF)   signals    

Body ‐ worn   Operation    

 

 

 

 

This   device   was   tested   for   typical   body ‐ worn   operations.

  A   minimum   separation   distance   must   be   maintained   between   the   user’s   body   and   the   handset,   including   the   antenna:   1   cm   to   comply   with  

  the   RF   exposure   requirements.

 

40 handheld

Algiz 10XB Manual

 

Industry   Canada   Warning   his   device   complies   with   Industry   Canada   license ‐ exempt   RSS   standard(s).

  Operation   is   subject   to   the   following   two   conditions:   (1)   this   device   may   not   cause   interference,   and   (2)   this   device   must   accept   any   interference,   including   interference   that   may   cause   undesired   operation   of   the   device.

  This   Class  

B   digital   apparatus   complies   with   Canadian   ICES ‐ 003.

  Le   present   appareil   est   conforme   aux   CNR   d'Ind ustrie   Canada   applicables   aux   appareils   radio   ex   empts   de   licence.

  L'exploitation   est   autorisee   aux   de ux   conditions   suivantes   :   (1)   l'appareil   nedoit   pas   produire   de   brouillage,   et   (2)   l'utilisateur   de   l'appar eil   doit   accepter   tout   brouillage   radioelectrique   subi,   meme   si   le   brouillage   est   susceptible   d'en   comp romettre   le   fonctionnement.

  

 

Operations   in   the   5.15Ghz

‐ 5.25Ghz

  band   are   restricted   to   indoor   usage   only.

  

41 handheld

advertisement

Related manuals