Allow remote access to your router management page. Trendnet XU8TEW818DRU
Add to my manuals
70 Pages
advertisement
TRENDnet User’s Guide x
Host Name: Personal URL provided to you by your Dynamic DNS service provider
(e.g. www.trendnet.dyndns.biz) x
User Name: The user name needed to log in to your Dynamic DNS service account x
Password: This is the password to gain access to Dynamic DNS service (NOT your router or wireless network password) for which you have signed up to.
Note: If you would like to discard the changes, click Cancel before you click Save .
Allow remote access to your router management page
Advanced > Administrator > Management
You may want to make changes to your router from a remote location such at your office or another location while away from your home.
1. Log into your router management page (see “ Access your router management page ” on page 17).
2. Click on the Advanced tab.
3. Click on the Administrator section and click on Management .
TEW-818DRU x
Remote Control: Select enable or disable for the feature. x
Port: Enter the port to assign remote access to the router. It is recommended to leave this setting as 8080.
Note: If you have configured port 8080 for another configuration section such as virtual server or special application, please change the port to use.
(Recommended port range 1024-65534)
Reset your router to factory defaults
Advance > Administrator > Settings Management
You may want to reset your router to factory defaults if you are encountering difficulties with your router and have attempted all other troubleshooting. Before you reset your router to defaults, if possible, you should backup your router configuration first, see
“ Backup and restore your router configuration settings ” on page 52.
There are two methods that can be used to reset your router to factory defaults. x
Reset Button – Located on the side panel of your router, see “ Product Hardware
Features ” on page 5. Use this method if you are encountering difficulties with accessing your router management page.
OR x
Router Management Page
1. Log into your router management page (see “ Access your router management page ” on page 17).
2. Click on the Advanced tab.
4. Review the setting on the Remote Management section. Click Apply to save settings
3. Click on the Administrator section and click on Settings Management .
© Copyright 2015 TRENDnet. All Rights Reserved.
51
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 2 Table of Contents
- 4 Product Overview
- 4 Package Contents
- 4 Features
- 5 Product Hardware Features
- 7 Application Diagram
- 7 Router Setup
- 7 Creating a Home Network
- 8 Router Installation
- 12 Connect additional wired devices to your network
- 12 Wireless Networking and Security
- 12 How to choose the type of security for your wireless network
- 13 Secure your wireless network
- 15 Connect wireless devices to your router
- 15 Connect wireless devices using WPS
- 17 Basic
- 17 Access your router management page
- 17 Network Status
- 18 Wireless settings
- 19 Guest Network
- 21 Steps to improve wireless connectivity
- 21 Parental Control
- 22 Doman/URL Filters
- 22 IP Filters (LAN Client Filters)
- 22 MAC Address Filters
- 23 ADVANCED
- 23 Change your router IP address
- 24 Set up the DHCP server on your router
- 24 Set up DHCP reservation
- 25 Manually configure your Internet connection
- 25 Clone a MAC address
- 26 Add static routes to your router
- 27 IPv6 Internet Connection Settings
- 28 Prioritize traffic using QoS (Quality of Service)
- 29 Advanced wireless settings
- 29 Multiple SSID
- 31 Wireless bridging using WDS (Wireless Distribution System)
- 32 Additional wireless settings
- 33 Set your router date and time
- 33 Create schedules
- 34 Access Control
- 35 Open a device on your network to the Internet
- 35 Virtual Server
- 36 Special Applications
- 37 Gaming
- 38 Enable/disable Application Layer Gateways (ALG)
- 39 Enable/disable UPnP on your router
- 39 Using External USB Storage
- 39 Samba Network File Server
- 40 FTP (File Transfer Protocol) Server
- 41 Properly Eject USB device
- 42 Print Share Utility Installation
- 42 Windows Installation
- 43 MAC OS X Installation
- 44 Launching the Utility
- 44 Utility Main Window
- 45 Configure Server
- 45 Connect
- 45 Disconnect
- 46 Sending a Request to Connect
- 47 Connect to a Printer
- 48 Auto-Connect Printer
- 48 Connect to a Scanner
- 49 Router Maintenance & Monitoring
- 49 Change your router login password
- 49 Change your device name
- 50 Change your device URL
- 50 Identify your network on the Internet
- 51 Allow remote access to your router management page
- 51 Reset your router to factory defaults
- 52 Router Default Settings
- 52 Backup and restore your router configuration settings
- 53 Upgrade your router firmware
- 54 Reboot your router
- 54 Allow/deny ping requests to your router from the Internet
- 55 Check the router system information
- 59 Router Management Page Structure
- 60 Technical Specifications
- 62 Troubleshooting
- 63 Appendix