3 Hardware Configuration. MCC MIIC-208, iPort/USB 2
Add to My manuals23 Pages
MCC MIIC-208 enables your computer to communicate with I2C devices. It supports Windows, Linux, and Mac OS X operating systems. This USB to I2C adapter features Circuit Sense technology, allowing it to work with I2C devices at voltages as low as 0.5V. It also offers high-performance processing for increased throughput.
advertisement
3 Hardware Configuration
3.1
Circuit Sense ™
The iPort/USB 2 introduces MCC’s Circuit Sense technology. Circuit Sense allow the I 2 C interface +V wire can operate in two modes, Power Source Mode and
Voltage Sense Mode. Mode selection is controlled by the MODE slide switch on the side of the unit enclosure.
• Power Source Mode - The +V wire can supply power (3.3v or 5v @ 100 mA)
Vcc to an external I 2 C Bus system. Voltage selection is controlled by the
SOURCE slide switch on the side of the unit enclosure. In Power Source Mode, the voltage of the iPort/USB 2 SCL, SDA, and /INT internal pull-ups, if enabled, and Voltage Sense circuit (0.3Vcc Low
MAX
, 0.7Vcc High
MIN
) is selected by the
SOURCE switch. (Use of the +V wire in Power Source Mode is user optional).
Power Source Mode is similar to the standard mode of operation on earlier versions of MCC I 2 C Bus host adapters.
• Voltage Sense Mode - The +V wire is connected to the external I 2 C Bus system pull-up supply voltage (0.5v to 5v) Vcc, and automatically adjusts iPort/USB 2
SCL, SDA, and /INT voltage sense circuit levels to match (0.3Vcc Low
MAX
,
0.7Vcc High
MIN
). In Voltage Sense Mode, the voltage of the iPort/USB 2 SCL,
SDA, and /INT internal pull-ups, if enabled, is equal to the external voltage
(Vcc) applied to the +V wire. (Use of the +V wire in Voltage Sense Mode is required).
3.2
Pull-up Resistors
I 2 C Bus systems are based on open-collector technology requiring pull-up devices on each signal wire (SCL, SDA, /INT). These pull-up devices usually take the form of pull-up resistors connected to bus power.
The I 2 C adapter includes a PULL-UPS slide switch used to enable or disable internal 1.8K ohm pull-up resistors attached to the SCL, SDA, and /INT lines.
Every I 2 C Bus system must have at least one pull-up on the signal lines. In some cases, the pull-ups may be present in the external I 2 C Bus circuit. Use this switch to configure the pull-up resistors for your system.
8
advertisement
Related manuals
advertisement
Table of contents
- 7 1 Overview
- 8 iPort/USB 2 Product Features
- 9 iPort/USB 2 Package
- 10 System Requirements
- 10 2 Interconnects
- 10 USB Connector
- 10 Virtual Communications Port (VCP)
- 11 C Mini Interface Connector
- 12 /INTerrupt Signal
- 13 3 Hardware Configuration
- 13 Pull-up Resistors
- 14 Connecting to an SMBus Target System
- 14 4 ESD (Electrostatic Discharge) Precautions
- 15 Host Computer Grounding
- 15 Grounding Solutions
- 16 5 Driver Software Set-Up
- 16 Driver Install
- 16 Driver Update
- 16 Driver Uninstall
- 17 6. Hardware Set-Up
- 17 USB Connection
- 17 C Bus Connection
- 18 7. Software Support
- 18 C Bus Communication Utilities
- 18 iPort Utility Pack for Windows
- 18 iPort Message Center
- 18 iPort Message Manager
- 18 C Bus EEPROM Programmer
- 19 C Bus Software Development Tools
- 19 MS.NET Class Library
- 19 LabVIEW VI Library
- 19 ASCII Command Interface
- 20 iPort/USB 2 Revision Report
- 20 Additional Information
- 21 C Connector Information
- 22 Declaration of Conformity