Set Features command. Seagate ST1000VNZ02 IronWolf 1TB, ST1000VN002 IronWolf 1TB, ST3000VN006 IronWolf 3TB, ST6000VN001 IronWolf 6TB, ST4000VN006 IronWolf 4TB, ST3000VN007 IronWolf 3TB, ST2000VN004 IronWolf 2TB, ST4000VN008 IronWolf 4TB
Add to My manuals40 Pages
advertisement
www.seagate.com
SATA Interface
82
H
86
H
90
H
AA
H
F1
H
06
H
07
H
10
H
55
H
4.3.2 Set Features command
This command controls the implementation of various features that the drive supports. When the drive receives this command, it sets BSY, checks the contents of the Features register, clears BSY and generates an interrupt. If the value in the register does not represent a feature that the drive supports, the command is aborted. Power-on default has the read look-ahead and write caching features enabled. The acceptable values for the Features register are defined as follows:
Table 15 Set Features commands
02
H
Enable write cache (default).
03
H
Set transfer mode (based on value in Sector Count register).
Sector Count register values:
00
H
Set PIO mode to default (PIO mode 2).
01
H
Set PIO mode to default and disable IORDY (PIO mode 2).
08
H
PIO mode 0
09
H
PIO mode 1
0A
H
PIO mode 2
0B
H
PIO mode 3
0C
H
PIO mode 4 (default)
20
H
Multiword DMA mode 0
21
H
Multiword DMA mode 1
22
H
Multiword DMA mode 2
40
H
Ultra DMA mode 0
41
H
Ultra DMA mode 1
42
H
Ultra DMA mode 2
43
H
Ultra DMA mode 3
44
H
Ultra DMA mode 4
45
H
Ultra DMA mode 5
46
H
Ultra DMA mode 6
Enable the PUIS feature set
PUIS feature set device spin-up
Enable use of SATA features
Disable read look-ahead (read cache) feature
Disable write cache
Disable the PUIS feature set
Disable use of SATA features
Enable read look-ahead (read cache) feature (default).
Report full capacity available
Note
At power-on, or after a hardware or software reset, the default values of the features are as indicated above.
Seagate IronWolf Product Manual, Rev. R 37
advertisement
Related manuals
advertisement
Table of contents
- 6 Seagate® Technology Support Services
- 7 Introduction
- 7 About the SATA interface
- 8 Drive Specifications
- 8 Specification summary tables
- 14 Formatted capacity
- 14 LBA mode
- 14 Default logical geometry
- 14 Start/stop times
- 15 Power specifications
- 15 Power consumption
- 18 Conducted noise
- 18 Voltage tolerance
- 18 Power-management modes
- 19 Environmental limits
- 19 Temperature
- 19 Humidity
- 19 Altitude
- 20 Shock
- 20 Vibration
- 21 Acoustics
- 21 Test for Prominent Discrete Tones (PDTs)
- 21 Electromagnetic immunity
- 22 Reliability
- 22 Annualized Failure Rate (AFR) and Mean Time Between Failures (MTBF)
- 22 HDD and SSD Regulatory Compliance and Safety
- 22 Regulatory models
- 22 Corrosive environment
- 23 Reference documents
- 23 Product warranty
- 24 Seagate® Rescue™ Data Recovery Service
- 26 Configuring and Mounting the Drive
- 26 Handling and static-discharge precautions
- 26 Configuring the drive
- 26 SATA cables and connectors
- 27 Drive mounting
- 31 SATA Interface
- 31 Hot-Plug compatibility
- 31 SATA device plug connector pin definitions
- 32 Supported ATA commands
- 34 Identify Device command
- 38 Set Features command
- 39 S.M.A.R.T. commands