advertisement
01CP-S225/X75/Vol1/E/最終 02.10.17 10:24 AM ページ23
USING THE MENU FUNCTIONS
VIDEO RGB SEARCH
STANDBY/ON
ASPECT AUTO BLANK
VOLUME
MAGNIFY
ON
OFF
FREEZE
MUTE
KEYSTONE
1
Press the MENU button MENU
The menu display appears on the screen. The projector has the following menus: MAIN,
PICTURE-1, PICTURE-2, INPUT, SCREEN, and
OPTION. Select a menu using the / buttons. The current settings of the items that can be manipulated via the selected menu appear.
POSITION
ESC
ENTER
MENU
RESET
2 Select a menu using the / buttons, then press the or ENTER button.
The display of the selected menu appears.
[ex. Adjusting SHARPNESS]
Use the / buttons to select PICTURE-1, then press the or ENTER button.
MENU
MAIN
PICTURE-1
PICTURE-2
INPUT
SCREEN
OPTION
ENTER
COLOR BAL R
COLOR BAL B
SHARPNESS
COLOR
TINT
–1
+1
–1
+1
–1
: SELECT
3 Select an item using the / buttons, then press the or ENTER button.
The operation display of the selected item appears. To adjust a numerical value, press the or ENTER button again to switch to the single menu (small display showing only the operation display area).
[ex. Adjusting SHARPNESS]
Use the press the
/ buttons to select SHARPNESS, then or ENTER button.
MENU
MAIN
PICTURE-1
PICTURE-2
INPUT
SCREEN
OPTION
COLOR BAL R
COLOR BAL B
SHARPNESS
COLOR
TINT
ENTER
0
: SELECT
4 Press the / buttons to adjust the level.
Press the MENU button to hide the menu and finish your operation. Alternatively, press the or ESC button to return to the previous display.
[ex. Adjusting SHARPNESS]
Use the / buttons to adjust the SHARPNESS.
© 3M 2003 3M™ Multimedia Projector S40/X40 23
24
MULTIFUNCTIONAL SETTINGS
This device has 6 separate menus: MAIN, PICTURE-1, PICTURE-2, INPUT,
SCREEN, OPTION. Each of these menus is operated using the same methods.
The basic operations of these menus are as follows.
Menu screen display : Press the " MENU " button.
Menu selection : Choose a menu name using the button or the ENTER button.
/
Item selection : Choose an item using the / button or the ENTER button.
button, and press the button, and press the
Return menu to last previous screen: Press the button or the ESC button.
Execution of settings and/or adjustments: Operate by using the / button. (For further details, read the explanation for each separate menu.)
Initialization of settings and/or adjustments: During operation, press the RESET button.
(Note that items whose functions are performed simultaneously with the operation of clock phase, language selection, automatic adjustment, etc., cannot be initialized.)
End menu operations: Press the MENU button, or do not perform any operation for several seconds.
MAIN Menu
With the MAIN menu, the seven items shown in the Table below can be performed.
Perform each operation in accordance with the instructions in the Table.
MAIN Menu
Item Description
MENU
MAIN
PICTURE-1
PICTURE-2
INPUT
SCREEN
OPTION
BRIGHT
CONTRAST
ASPECT
PICT. POSIT.
GAMMA
MIRROR
LANGUAGE
12
: SELECT
Example : MAIN Menu
(BRIGHT)
BRIGHT
CONTRAST
ASPECT
PICT.POSIT.
GAMMA
MIRROR
LANGUAGE
Adjust Brightness: Light ⇔ Dark
Adjust Contrast: Strong ⇔ Weak
Select Aspect Ratio:
At rgb Input or Hi-Vision 1125i(1035i/1080i)/750p of component video
Input:
4:3 ⇔ 16:9
At video Input, s-video Input or 525i/525p/625i of component video Input:
4:3 ⇔ 16:9 ⇔ SMALL
• The SMALL picture may not be displayed correctly with certain input signals.
Select Picture Position (for 16:9/SMALL Picture):
TOP ⇔ CENTER ⇔ BOTTOM
Select Gamma Mode:
NORMAL ⇔ CINEMA ⇔ DYNAMIC
Select Mirror Status:
NORMAL ⇔ H:INVERT ⇔ V:INVERT ⇔ H&V:INVERT
Select Menu Language:
ENGLISH
⇔
日本語
⇔
ITALIANO
⇔
FRANÇAIS
⇔
⇔ DEUTSCH
NORSK ⇔
⇔
NEDERLANDS
POTUGUÊS ⇔ 中文 ⇔
ESPAÑOL
⇔
© 3M 2003 3M™ Multimedia Projector S40/X40
PICTURE-1 Menu
With the PICTURE-1 menu, the five items shown in the Table below can be performed.
Perform each operation in accordance with the instructions in the
Table.
PICTURE-1 Menu
Item Description
COLOR BAL R Adjust Red Color Balance: Dark ⇔ Light
MENU
MAIN
PICTURE-1
PICTURE-2
INPUT
SCREEN
OPTION
COLOR BAL R
COLOR BAL B
SHARPNESS
COLOR
TINT
12
: SELECT
Example : PICTURE-1 Menu
(COLOR BAL R)
COLOR BAL B Adjust Blue Color Balance: Dark ⇔ Light
SHARPNESS Adjust Sharpness (for VIDEO/S-VIDEO): Clear
COLOR
Adjust COLOR (for video
/ s
video
/ component video
):
Dark ⇔ Light
⇔
TINT Adjust Tint (for video
/ s
video
): Green ⇔ Red
Soft
PICTURE-2 Menu
With the PICTURE-2 menu, the four items shown in the Table below can be performed.
Perform each operation in accordance with the instructions in the
Table.
MENU
MAIN
PICTURE-1
PICTURE-2
INPUT
SCREEN
OPTION
V POSITION
H POSITION
H PHASE
H SIZE
12
: SELECT
Example : PICTURE-2 Menu
(V POSITION)
PICTURE-2 Menu
Item Description
V POSITION Adjust Vertical Position (for rgb
): Up ⇔ Down
H POSITION
H PHASE
Adjust Horizontal Position (for rgb
): Left ⇔ Right
Adjust Horizontal Phase (for rgb
/ component video
):
Right ⇔ Left
• Adjust to eliminate flicker.
H SIZE
Adjust Horizontal Size (for rgb
): Large ⇔ Small
• If the horizontal size adjustment is excessive, the image may not be displayed correctly. In such a case, initialize H SIZE with the RESET button.
© 3M 2003 3M™ Multimedia Projector S40/X40 25
26
MULTIFUNCTIONAL SETTINGS (continued)
INPUT Menu
MENU
MAIN
PICTURE-1
PICTURE-2
INPUT
SCREEN
OPTION
AUTO
VIDEO
HDTV
SYNC ON G
EXECUTE
With the INPUT menu, the four items shown in the Table below can be performed. With inputting of rgb in
signal, the horizontal and vertical frequencies of the signal will be displayed on the initial screen of the
INPUT menu.
Perform each operation in accordance with the instructions in the Table.
: SELECT
Example : INPUT Menu
(AUTO)
INPUT Menu
Item
AUTO
VIDEO
Description
Auto Adjust (for rgb
): Automatically adjusts H POSITION, V POSITION, H
PHASE, and H SIZE. Use this function with the maximum window size.
Auto Adjust (for video
/ s
video
): Automatically selects the proper VIDEO mode for the current input signal. This function is active only when the AUTO mode is selected for the item VIDEO. Refer to the description for the item
VIDEO below.
• This function may not be available with a PAL60 signal and certain other signals.
• The AUTO mode operation requires approximately 10 seconds.
• For component video, the signal type is identified automatically even if this function is inactive. For a HDTV signal, refer to the item HDTV below.
Select Mode of Signal Type (for video
/ s
video
):
AUTO ⇔ NTSC ⇔ PAL ⇔ SECAM ⇔
NTSC4.43 ⇔ M-PAL ⇔ N-PAL
Selecting AUTO mode activates and performs the AUTO function for video/svideo. It automatically selects the proper mode from among those above.
Use this function if the image becomes unstable with video/s-video. (e.g.
The image becomes irregular, or lacks color.)
• AUTO mode may not function correctly with a PAL60 signal and certain other signals.
• The AUTO mode operation requires approximately 10 seconds.
• For component video, the signal type is identified automatically even if this function is inactive. For a HDTV signal, refer to the item HDTV below.
HDTV
Select HDTV Signal Mode:
1080i ⇔ 1035i
• If the selected HDTV mode is incompatible with the input signal, the picture may be distorted.
SYNC ON G
On/Off SYNC ON G Mode:
TURN ON ⇔ TURN OFF
Selecting TURN ON turns on the SYNC ON G mode. The SYNC ON G mode allows reception of SYNC on G.
• In the SYNC ON G mode, the picture may be distorted with certain input signals. In such a case, remove the signal connector so that no signal is received and turn SYNC ON G off, and then reconnect the signal.
© 3M 2003 3M™ Multimedia Projector S40/X40
SCREEN Menu
MENU
MAIN
PICTURE-1
PICTURE-2
INPUT
SCREEN
OPTION
BLANK
START UP
With the SCREEN menu, the two items shown in the Table below can be performed.
Please perform each operation in accordance with the instructions in the Table.
: SELECT
Example : SCREEN Menu
(BLANK)
SCREEN Menu
Item
BLANK
Description
Selection of BLANK Screen:
.
. ⇔ . . ⇔ .
.
The BLANK Screen may be voluntarily selected. The BLANK Screen is displayed when the screen has been erased (i.e., made to vanish) by manipulating the BLANK button (please refer to the “Temporarily Blanking the
Screen” section).
Option screens: Various colored non-patterned (plain) screens displayed within the Menus.
START UP
Selection of START UP Screen:
TURN ON ⇔ TURN OFF
The START UP Screen may be voluntarily selected. The START UP Screen is displayed when no signal has been inputted, or when spec signals are being inputted.
TURN ON: Existing standard screens. Please make confirmation using the actual screen(s).
TURN OFF: A non-patterned (plain) blue color screen.
• Note that if TURN OFF is selected the blank screen is displayed in blue when there is no signal.
© 3M 2003 3M™ Multimedia Projector S40/X40 27
28
MULTIFUNCTIONAL SETTINGS (continued)
OPTION Menu
With the OPTION menu, the five items shown in the Table below can be performed.
Please perform each operation in accordance with the instructions in the Table.
MENU
MAIN
PICTURE-1
PICTURE-2
INPUT
SCREEN
OPTION
VOLUME
AUTO OFF
WHISPER
LAMP TIME
FILTER TIME
12
: SELECT
Example : OPTION Menu
(VOLUME)
OPTION Menu
Item
VOLUME
AUTO OFF
WHISPER
LAMP TIME
FILTER TIME
Description
Adjust Volume: High ⇔ Low
Adjust AUTO OFF Time:
Long (MAX. 99 min.) ⇔ Short (Min. 1 min.) ⇔ (DISABLE: 0 min.)
The system automatically enters the standby mode if no signal is received within the set time. This function is inactive when DISABLE (0 min.) is selected.
Select WHISPER Mode:
NORMAL ⇔ WHISPER
When WHISPER is selected the WHISPER mode is activated. In the WHISPER mode, acoustic noise and screen brightness are reduced.
Refer to LAMP TIME: When set, this function displays the total time the projector lamp has been used since new.
Reset LAMP TIME [Use this function only when the lamp has been replaced!]:
Depress the RESET button for at least 3 seconds while lamp time is being displayed. The reset menu will then appear. After you replace the lamp with a new lamp, select RESET on the menu with the button.
• Do not reset the lamp time unless you have replaced the lamp. And, always reset the lamp time when replacing the lamp. The message functions will not operate properly if the lamp time is not reset correctly.
• Before replacing the lamp, carefully read the descriptions headed "THE
LAMP".
Refer to FILTER TIME: This function displays the total time the air-filter has been used since new.
Reset FILTER TIME [Use this function only when the filter is cleaned or replaced!]:
Depress the RESET button for at least 3 seconds while filter time is being displayed. The reset menu will then appear. After you replace the filter, select
RESET on the menu with the
RESET ⇔ CANCEL button.
• Do not reset the filter time unless you have cleaned or replaced the filter. And, always reset the filter time when cleaning or replacing the filter. The message functions will not operate properly if the filter time is not reset correctly.
• Before cleaning or replacing the filter, carefully read the descriptions headed "THE AIR FILTER".
© 3M 2003 3M™ Multimedia Projector S40/X40
advertisement
Related manuals
advertisement
Table of contents
- 3 Projector Features
- 3 Preparations
- 5 Part Names
- 7 Setting Up
- 9 Connecting Your Devices
- 13 Using the Remote Control
- 13 Operating the Projector
- 15 Turning On the Power
- 17 Turning Off the Power
- 18 Adjusting the Volume
- 18 Muting the Sound
- 19 Adjusting the Position
- 20 Auto Adjustment Feature
- 21 Correcting Keystone Distortions
- 22 Magnify Feature
- 22 Freezing the Screen
- 23 Signal Searching
- 23 Selecting the Aspect Ration
- 23 Blanking the Screen
- 24 Menu Functions
- 25 MAIN Menu
- 26 PICTURE-1 Menu
- 26 PICTURE-2 Menu
- 27 INPUT Menu
- 28 SCREEN Menu
- 29 OPTION Menu
- 30 LAMP
- 32 Air Filter
- 34 Other Care
- 36 Troubleshooting
- 36 Indicator Lamps
- 37 General Phenomena
- 38 Specifications