- Vehicles & accessories
- Motor vehicle electronics
- Car audio amplifiers
- Delta Tau
- PMAC2 PCI
- Owner's manual
advertisement
▼
Scroll to page 2
of
45
PMAC2 PCI Hardware Reference Manual
E10A, B, C: Flash Memory Bank Select
E Point and
Physical Layout
E10A
Description Default
Remove all three jumpers to select flash memory bank with factory-installed firmware.
Use other configuration to select one of the seven other flash memory banks.
No jumpers installed
E10C
Flex CPU Board Jumper Descriptions 11
advertisement
Related manuals
advertisement
Table of contents
- 5 INTRODUCTION
- 5 Board Configuration
- 5 Base Version
- 5 Option 1: Additional Four Channels Axis Interface Circuitry
- 5 Option 2: Dual-Ported RAM
- 6 Option 5xF: CPU Speed Options
- 6 Option 6: Extended Servo Algorithm
- 6 Option 7: Plate Mounting
- 6 Option 8: High-Accuracy Clock Crystal
- 6 Option 10: Firmware Version Specification
- 6 Option 12: Analog-to-Digital Converters
- 6 Option 16: Battery-Backed Parameter Memory
- 7 HARDWARE SETUP
- 7 Piggyback CPU Board Jumper Configuration
- 7 Watchdog Timer Jumper
- 7 Dual-ported RAM Source Jumper
- 7 Power-Up State Jumpers
- 7 Firmware Load Jumper
- 7 Flash Memory Bank Select Jumpers
- 7 Base Board Jumper Configuration
- 7 Servo and Phase Clock Direction Control
- 8 CPU Frequency Control Jumpers
- 8 Re-Initialization Jumper
- 8 Encoder Sample Clock Source Jumpers
- 8 Serial Port Selection Jumper
- 8 Output Disable State Jumpers
- 9 Resistor Pack Configuration
- 9 Termination Resistors
- 9 Pull-Up/Pull-Down Resistors
- 10 Connections
- 10 Mounting
- 10 Power Supply Connection
- 10 Machine Port Connections
- 10 Display Port
- 11 Multiplexer Port
- 11 I/O Port
- 11 Serial Ports
- 11 A/D-Converter Port
- 11 Handwheel Port
- 12 COMMUNICATIONS SETUP
- 14 FLEX CPU BOARD JUMPER DESCRIPTIONS
- 14 E1: Watchdog Disable Jumper
- 14 E2: Dual-Ported RAM Port Select
- 14 E4 – E6: Power-Up/Reset Load Source
- 14 E7: Firmware Reload Enable
- 15 E10A, B, C: Flash Memory Bank Select
- 16 PMAC2 PCI BASE BOARD JUMPER DESCRIPTIONS
- 16 E2: CPU Frequency Select
- 16 E3: Normal/Re-Initializing Power-Up/Reset
- 16 E4: CPU Frequency Select
- 17 E5 – E6: (Reserved for Future Use)
- 17 E13 - E14: Encoder Sample Clock Direction Control
- 17 E17 - E18: Serial Port Type Selection
- 18 E111-118: Command Output Disable State
- 19 MATING CONNECTORS
- 19 CPU Board Connectors
- 19 J2 (JEXP)/Expansion
- 19 Baseboard Connectors
- 19 J1 (JANA)/Analog (Option 12)
- 19 J2 (JTHW)/Multiplexer Port
- 19 J3 (JIO)/Digital I/O
- 19 J5 (JRS232)/RS-232 Serial Communications
- 19 J5A (JRS422)/RS-422 Serial Communications
- 19 J6 (JDISP)/Display
- 19 J7 (JHW)/Auxiliary Channel
- 20 J8 (JEQU)/Position Compare
- 20 J9 (JMACH1)/Machine Port
- 20 J10 (JMACH2)/Machine Port
- 20 J11 (JMACH3)/Machine Port
- 20 J12 (JMACH4)/Machine Port
- 21 PMAC2 PCI BASE BOARD CONNECTOR PINOUTS
- 21 J1 (JANA) Analog Input Port Connector
- 22 J2 (JTHW) Multiplexer Port Connector
- 23 J3 (JI/O) General Input/Output Connector
- 24 J5 (JRS232) Serial Port Connector
- 24 J5A (RS422) Serial Port Connector
- 25 J6 (JDISP) Display Connector
- 25 J7 (JHW) Handwheel Encoder Connector
- 26 J8 (JEQU) Position Compare Output Connector
- 26 J9 (JMACH1) Connector Description
- 27 J9 JMACH1 Connector
- 29 J10 (JMACH2) Connector Description
- 32 J11 (JMACH3) Connector Description
- 33 J11 JMACH3 Connector
- 35 J12 (JMACH4) Connector Description
- 36 J12 JMACH4 Connector
- 38 TB1 (2/4-Pin Terminal Block)
- 39 TB2 (3-Pin Terminal Block)
- 40 BASE BOARD JUMPERS LAYOUT
- 41 SCHEMATICS