advertisement
SC835X Chassis Manual
Installing the Optional Slim DVD Drive
The chassis supports a slim DVD drive just under the control panel.
1. Power down the system as described in Section 5-2. and remove the cover.
2. If a new front port panel is not being installed, remove the mini-bezel from the drive bay The mini-bezel is the small grating that covers the drive bay.
Remove this by simply pulling it out of the bay.
If a new front port panel is being installed, remove the old drive by depressing the release tab, then pulling the drive out of the chassis.
3. Insert the new drive unit in the slot until the tab locks into place.
4. Connect the data and power cables to the backplane and, if necessary, motherboard.
Figure 5-5. Installing the Slim DVD Drive
Using the 5.25" Full--Height Bays
The two horizontal drive bays can be filled with:
•
Additional hard disk drives, each tray housing either one 3.5" drive or two 2.5" drives using an optional bracket
•
Peripheral drives, such as DVD, CD or floppy drives
•
Eight 2.5" hot-swap hard disk drives in a mobile rack (SCM28)
The vertically oriented 3.5" bay near the center front can also house a drive.
5-6
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 32 1-1 Overview
- 32 Shipping List
- 32 Part Numbers
- 32 Contacting Supermicro
- 32 Returning Merchandise for Service
- 33 About Standardized Warning Statements
- 33 Warning Definition
- 33 Installation Instructions
- 33 Circuit Breaker
- 33 Power Disconnection Warning
- 33 Equipment Installation
- 33 Restricted Area
- 33 Battery Handling
- 33 Redundant Power Supplies
- 33 Backplane Voltage
- 33 Comply with Local and National Electrical Codes
- 33 Product Disposal
- 33 Hot Swap Fan Warning
- 33 Power Cable and AC Adapter
- 34 3-1 Components
- 34 Drive Bays
- 34 Motherboard Support
- 34 Backplane
- 34 Power Supply
- 34 Air Shroud
- 34 Switches and Status Indicators
- 34 I/O Expansion slots
- 34 Mounting Rails
- 34 Unpacking the System
- 34 Where to get Replacement Components
- 44 4-1 Overview
- 44 Control Panel Buttons
- 44 Control Panel LEDs
- 44 Drive Carrier LEDs
- 45 5-1 Overview
- 45 Removing the Power Cord
- 45 Removing the Chassis Cover
- 45 Installing Drives
- 45 Installing 3.5" Hard Drives
- 45 Installing the Optional Slim DVD Drive
- 45 Using the 5.25" Full--Height Bays
- 45 Installing the Motherboard
- 45 Permanent and Optional Standoffs
- 45 Standoff Labeling
- 45 Motherboard Installation Procedure
- 45 Installing Expansion Cards
- 45 Installing an I/O Shield
- 45 Installing Cooling Elements
- 45 System Fans
- 45 Replacing a System Fan
- 45 Rear System Fans
- 45 Installing the Rear System Fans
- 45 GPU Cooling Option
- 45 Checking the Server Air Flow
- 45 Power Supply
- 45 Replacing the Power Supply
- 45 Replacing the Power Distributor
- 45 Optional Battery Backup Power
- 46 Preparing for Setup
- 46 Choosing a Setup Location
- 46 Ambient Operating Temperature
- 46 Adequate Airflow
- 46 Circuit Overloading
- 46 Reliable Ground
- 46 Physical Rack Precautions
- 46 General Server Precautions