- No category
advertisement
Chapter 7. Maintenance and Guarantee
This chapter describes how to maintenance, repair provisions and how to request for repair.
7.1 Maintenance ............................................................................................................................... 74
7.2 Guarantee .................................................................................................................................... 74
7.3 Repair Provisions........................................................................................................................ 74
7.4 How to Request for Repair ......................................................................................................... 75
( 73 / 77 )
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 6 Chapter 1. Precautions for Safety
- 8 1.1 Safety Symbols and Meanings
- 20 Chapter 2. Preparation
- 21 2.1 Terminology
- 22 2.2 Package Components
- 22 2.3 Other Tool Products Required for Development
- 23 2.4 Name of Each Part
- 23 (1) System Configuration
- 24 (2) Inside of Emulation Pod
- 25 2.5 When Using the Emulator for the First Time
- 26 Chapter 3. Setting Up
- 27 3.1 Removing the Upper Cover
- 28 3.2 Setting Switches and Pullup Resistors
- 32 3.3 Selecting Clock Supply
- 33 (1) Using the Oscillator Circuit on the Target System
- 34 (2) Changing the Internal Oscillator Circuit of the Emulation Pod
- 35 (3) Replacing the Oscillator Circuit Boards
- 36 3.4 A-D Conversion Bypass Capacitor
- 37 3.5 Connecting the PC4701 and Emulation Pod
- 37 (1) Connecting the Cable to the PC
- 38 (2) Connecting the Cable to the Emulation Pod
- 39 3.6 Connecting the Target System
- 40 (1) Connecting 100-pin 0.65-mm-pitch LCC Socket
- 41 (2) Connecting 100-pin 0.65-mm-pitch Foot Pattern (Part 1)
- 42 (3) Connecting 100-pin 0.65-mm-pitch Foot Pattern (Part 2)
- 43 (4) Connecting 100-pin 0.65-mm-pitch Foot Pattern (Part 3)
- 44 3.7 Procedure for Making MCU File for PD
- 46 Chapter 4. Usage
- 47 4.1 Turning On the Power
- 47 (1) Checking the Connection of Emulator System
- 47 (2) Turning On the Power
- 48 (3) LED Display When PC4701 Starts Up Normally
- 49 4.2 Downloading Firmware
- 49 (1) When It is Necessary to Download Firmware
- 49 (2) Downloading Firmware in the Maintenance Mode
- 50 4.3 Self-checks
- 50 (1) Self-check Procedure
- 50 (2) If an Error is Detected in Self-checks
- 52 Chapter 5. Specifications
- 53 5.1 Specifications
- 54 5.2 Operation Timing in Memory Expansion Mode and Microprocessor Mode (5 V)
- 54 (1) Separate Bus, No-wait
- 56 (2) Separate Bus, With Wait, Accessing External Memory Area
- 58 (3) Multiplex Bus, With Wait, Accessing External Memory Area
- 60 (4) Timing Requirements
- 62 5.3 Electrical Characteristics
- 63 5.4 Connection Diagram
- 64 5.5 External Dimensions
- 64 (1) External Dimensions of the Emulation Pod
- 65 (2) External Dimensions of the Converter Board (FLX-100LCC)
- 65 (3) Reference Dimensional Drawing for 100-pin 0.65-mm-pitch QFP Foot Patterns
- 66 Chapter 6. Troubleshooting
- 67 6.1 Flowchart to Remedy the Troubles
- 68 6.2 When the Emulator Debugger Does Not Start Up Properly
- 68 (1) When the LED Display of PC4701 is Abnormal
- 69 (When the target system is connected)
- 70 (When the target system is not connected)
- 71 6.3 Operation Differs from That of Actual MCUs
- 71 (1) Cannot Reset from the Target System
- 71 (2) Data Values of ROM Area at Power-on Are Different
- 71 (3) HOLD* Control
- 71 (4) A-D Conversion Values are Different from Expected Values
- 72 Chapter 7. Maintenance and Guarantee
- 73 7.1 Maintenance
- 73 7.2 Guarantee
- 73 7.3 Repair Provisions
- 74 7.4 How to Request for Repair