Quick Start. Aetertek AT-918

Quick Start

ON

ON

ON

02

01

00

6

Step 6:

Check the button function. Push the beep button, the receiver will produce beeping sound and

8

Step 8 :

Choose the dog mode (Dog1, dog2 or dog00). By pushing the dog switch button in the left of the transmitter, similarly, push the vibrate button, it will produce you can train the different dog separately by synced the vibration.Cap the shock test kit on the metal prongs, and push the shock button. If the bulb lights up, shock

function is ok.

Step 7:

Adjust the intensity of the shock functions. There are 2 buttons on the transmitter's right side: Up button and Down button. Up button is to increase while Down button is to decrease the intensity of shock.

time.

7

10

0

10

0

ON

Tip 3: Longer(shorter) holding beep, vibrate or shock button will lead to longer (shorter) duration of beep, vibrate or shock

receiver one by one. If Dog00 is selected, both dogs will receive correctional signals.

Step 9:

There is a Flashlight button on the back of the transmitter. Push and hold

9 the Flashlight button for 3 seconds to turn Flashlight on/off.

Step 10:

Start to train. Put the collar into the receiver and wear the receiver around dog’s neck. Remember to leave one finger place

between collar and neck, then it’s ready to train.

Tip 4: To do a self-test, press the On/Off button of receiver three times it should beep, vibrate and shock, indicating a functional unit.

Tip 5: Auto Anti Bark function which default setting is off is available.

Short press flashlight to turn on /off auto anti bark mode. The auto mode icon (SPEAKER) will display ON/OFF accordingly. You can alter receivers' auto anti bark status(ON or OFF simultaneously) in dog 00 system, both receivers' initial setting will probably be changed. In this case, when you go back to the other 2 systems, remember to push one of function buttons to update the auto anti bark status in the current dog system; After updated anti bark status, the auto mode icon will tell you what the exact anti bark status is. Please turn auto anti bark function off timely when not in use.

-03-

Trouble Shooting

A：Transmitter /Receiver runs out of batteries quickly.

1：Make sure the charger and Transmitter/Receiver are securely connected.

2：Charge it up to 3 hours or above.

B：Transmitter doesn't work.

R

Professional Dog Trainer

AT-919

Replace the 9v dry battery with a new one or recharge the Transmitter.

C：Transmitter can't match Receiver successfully.

1：Make sure the intensity level is not on ZERO.

2：Check whether the antenna is installed correctly or not.

3：Ensure the receiver is turned on and in sync waiting status.

D：Receiver doesn't response to Transmitter.

1：Make sure the intensity level is not on ZERO.

2：Make sure Receiver had been synced with Transmitter and Transmitter is in the right dog system. Never change dog system after

the system had been synced!

3：Make sure the Receiver and Transmitter have enough power.

E：The training system has no effect on my dog.

1：Make sure the Receiver is working and the shocking prongs touch dog's skin closely.

2：Try increasing the intensity level.

F：Transmitter can't remotely control 1-2 or 1-3 Receivers.

1：Make sure you sync different Receiver separately.

2：Only in the right dog system, can you operate the corresponding Receiver or dog.

3：Whenever the Receiver/Transmitter out of power and recharged, you need to sync them once again.

G：The training system is only available in short range.

1

2

：

：

Check whether the antenna is installed correctly.

3

Make sure there don't have strong signal interference from your surroundings.

：

Remote control range could be fluctuated along with surroundings, obstacles, or even the weather.

4

：

As to AT-919, make sure the collar had been put through the antenna pole in the back side of Receiver.

-04-