- No category
advertisement
9 Connecting to the Camera
9.1 Camera Connection Procedures
Please carry out the following procedures to connect a mobile device to the PHANTOM 2 VISION.
1.
2.
3.
4.
5.
Power on the remote controller and the range extender.
Make sure the switch on the back of the camera is set to “WIFI ON” and then power on the PHANTOM 2
VISION.
(Fig.1)Enable the Wi-Fi on your mobile device; wait for about 30 seconds, and then select the
Phantom_xxxxxx from theWi-Fi network list.
(Fig.2)Run the DJI VISION App on your mobile device which will indicate the current Wi-Fi connection status on the main menu. The Wi-Fi connection indicator will turn solid green which means the connection is good.
Tap the “CAMERA” icon and the DJI VISION App will establish a live camera preview (Fig.3). This means everything is now functioning.
Enable the Wi-Fi
Wi-Fi Connection
Indicator
Select Phantom_xxxxxx
Fig.1 Fig.2
©2013-2014 DJI Innovations. All Rights Reserved.
28 |
Fig.3
Wi-Fi Connection Indicator Description
Icon
Description
Solid green Wi-Fi is now connected to the PHANTOM 2 VISION.
Solid blue Wi-Fi is connected to another Wi-Fi network and NOT to the PHANTOM 2 VISION.
Off No Wi-Fi connection.
(1)
(2)
The first time you launch the DJI VISION App, Internet access is required to finish the login process or new account creation.
The SSID is unique for each PHANTOM 2 VISION which should appear in your Wi-Fi list as
Phantom_xxxxxx. Always connect to the SSID starting with Phantom_xxxxxx. FC200_0xxxxx is the
SSID of the camera and should not be connected to. If the SSID FC200_0xxxxx is connected to, then the connection signal range will be extremely shortened.
©2013-2014 DJI Innovations. All Rights Reserved.
29 |
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 2 Index
- 4 In the Box
- 4 Required Items
- 5 Symbol Legend
- 5 Watch the Quick Start Videos
- 5 Downloading the DJI VISION App
- 6 1 Attaching the Propellers
- 6 1.1 Introduction
- 6 1.2 Assembly
- 6 1.3 Removing the Propellers
- 6 1.4 Notes
- 7 2 Installing the Range Extender and Mobile Device Holder
- 7 2.1 Installing the Range Extender
- 7 2.2 Installing the Mobile Device Holder
- 8 3 Preparing the Remote Controller
- 8 3.1 The Remote Controller
- 8 3.2 Power on the Remote Controller
- 9 3.3 Remote Controller Power Indicator Status Information
- 9 3.4 Antenna Orientation
- 10 3.5 Remote Controller Operation
- 11 3.6 Link between the Remote Controller and Receiver
- 12 Link Procedures
- 12 Link Indicator
- 12 3.7 Compliance Version Configuration
- 14 4 Preparing the Range Extender
- 14 4.1 The Range Extender
- 14 4.2 Function Description
- 15 4.3 Powering on the Range Extender
- 15 4.4 How to Bind the Camera & Range Extender
- 18 5 Preparing the Camera
- 18 5.1 The built-in camera
- 18 5.2 Main Functions
- 20 5.3 Upgrading the Firmware of Camera
- 21 6 Downloading and Installing the DJI VISION App
- 21 6.1 Download and Install
- 21 6.2 Register & Login
- 23 7 Preparing the Flight Battery
- 23 7.1 Intelligent Battery and Charger Instructions
- 23 7.2 Charging Procedures
- 24 7.3 Install the Battery
- 24 7.4 Battery Usage
- 24 Description of the Battery Level Indicator
- 25 7.5 Correct Battery Usage Notes
- 26 8 PHANTOM 2 Aircraft
- 26 8.1 The Aircraft
- 26 8.2 Built-in Flight Control System Instructions
- 26 8.3 LED Flight Indicators Description
- 28 9 Connecting to the Camera
- 28 9.1 Camera Connection Procedures
- 30 10 Calibrating the Compass
- 30 10.1 Calibration Warnings
- 30 10.2 Calibration Procedures
- 30 10.3 When Recalibration is Required
- 31 11 Flight
- 31 11.1 Flying Environment Requirements
- 31 11.2 Starting the Motors
- 31 11.3 Takeoff/Landing Procedures
- 32 11.4 Failsafe Function
- 33 Home Point
- 33 Go Home Procedures
- 33 Regaining Control During Failsafe Procedure
- 34 Failsafe on the DJI VISION App
- 34 11.5 Low Battery Capacity Warning Function
- 34 DJI VISION App Low Battery Capacity Warning
- 36 12 DJI VISION App Usage
- 36 12.1 DJI VISION App Main Menu
- 36 12.2 Camera Page
- 36 Basic Use
- 40 Camera Settings
- 43 12.3 Album Page
- 43 Camera SD CARD Album
- 44 Mobile Device Album
- 45 12.4 News Page
- 46 12.5 Settings Page
- 50 13 Assistant Software Installation and Configuration
- 50 13.1 Installing Driver and PHANTOM 2 VISION Assistant Software
- 51 13.2 Using the PHANTOM 2 VISION Assistant Software on a PC
- 52 13.3 Firmware upgrade of the PHANTOM 2 VISION
- 53 13.4 PHANTOM RC Assistant Software Description
- 55 14 Troubleshooting(FAQ)
- 58 15 Appendix
- 58 LED Flight Indicator Status
- 59 Specifications