advertisement
▼
Scroll to page 2
of 50
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 7 1.1. Overview
- 7 1.2. Package Check List
- 7 1.2.1. Single Unit Package
- 7 1.2.2. Bulk-Pack Package
- 8 1.3. Product Specification
- 10 2.1. Panel Layout
- 11 2.2. Connecting the Hardware
- 11 2.2.1. Connecting Power to Parani-SD
- 12 2.2.2. Connecting Device to Parani-SD
- 12 2.2.3. Attaching Batter Pack to Parani-SD
- 13 3.1. Operation Modes
- 13 3.2. LED Indicators
- 14 3.3. Serial Ports
- 14 3.4 Data Bit
- 14 3.5 Hardware Flow Control
- 15 3.6 Reset to Factory Defaults
- 15 3.7 Dipswitch
- 15 3.8 Pairing Button
- 17 3.9 Software and Utility
- 17 3.10 ParaniWIN
- 23 3.11 ParaniUpdater
- 23 3.12 Terminal Program
- 25 4.1. FCC
- 25 4.1.1. FCC Compliance Statement
- 25 4.1.2. RF Exposure Statement
- 25 4.1.3. Do not
- 25 4.2. CE
- 25 4.2.1. EC-R&TTE Directive
- 25 4.3. MIC
- 25 4.4. Telec
- 25 4.5. SIG
- 26 5.1. Radio Frequency Range
- 26 5.2. Number of Frequency Channel
- 26 5.3. Transmission Method
- 26 5.4. Modulation Method
- 26 5.5. Radio Output Power
- 26 5.6. Receiving Sensitivity
- 26 5.7. Power Supply
- 27 A.1. Serial Port Pin Outs
- 28 A.2. Serial Wiring Diagram
- 28 A.2.1. To Host with DTE Interface
- 28 A.2.2. To Host with DCE Interface
- 29 B.1. Terminology
- 29 B.1.1. AT Command
- 29 B.1.2. AT Response
- 29 B.1.3. Operation Mode
- 29 B.1.4. Operation Status
- 29 B.1.5. Security
- 30 B.1.6. Symbols
- 30 B.2. Command Category
- 31 B.3. Command Description
- 39 B.4. Command Validity
- 41 C.1. S1: Force to Reconnect (default 1)
- 41 C.2. S3: Stream UART Policy (default 0)
- 41 C.3. S4: Enable Remote Name Query (default 1)
- 41 C.4. S6: Enable Low Power Mode (default 0)
- 41 C.5. S10: Enable Response Message (default 1)
- 41 C.6. S11: Enable Escape (default 1)
- 42 C.7. S12: Clear Data Buffer When Disconnected (default 0)
- 42 C.8. S13: Enable DCD Signal (default 1)
- 42 C.9. S14: Enable DTR Transfer (default 1)
- 42 C.10. S15: Enable Disconnect by DTR (default 0)
- 42 C.11. S22: Faster Connection (default 0)
- 42 C.12. S23: Intercharacter Timeout Setting (default 0)
- 42 C.13. S24: Maximum Number of Inquiry Result (default 10)
- 42 C.14. S26: Intercharacter Timeout (default 0)
- 43 C.15. S28: Escape Sequence Character (default 43)
- 43 C.16. S31: Page Timeout (default 300)
- 43 C.17. S33: Inquiry Timeout (default 30)
- 43 C.18. S37: Supervision Timeout (default 16000)
- 43 C.19. S43: COD (default 001F00)
- 43 C.20. S44: COD Filter (default 000000)
- 43 C.21. S45: IAC(Inquiry access code)
- 43 C.22. S46: BD Address of Last Connected Device
- 43 C.23. S47: Select Low Power Mode (default 0)
- 44 C.24. S48: Low Power Max Interval (default 2048)
- 44 C.25. S49: Low Power Min Interval (default 800)
- 44 C.26. S50: Low Power Sniff Attempt (default 8)
- 44 C.27. S51: Low Power Sniff Timeout (default 8)
- 44 C.28. S52: Low Power Park Timeout (default 5)
- 45 D.1. No Data Transmission
- 45 D.1.1. COM Port Settings
- 45 D.1.2. Pin Assignment
- 45 D.2. Data Loss or Malfunctioning
- 45 D.2.1. Hardware Flow Control
- 45 D.2.2. Response Message
- 45 D.3. Transmission Delay
- 45 D.3.1. RF Processing Delay
- 45 D.3.2. RF Transmission Environment
- 46 E.1. Parani-SD100 mechanical drawing
- 47 E.2. Parani-SD200 mechanical drawing
- 48 E.3. Parani-SD200 battery pack mechanical drawing
- 49 F.1. GENERAL WARRANTY POLICY
- 49 F.2. LIMITATION OF LIABILITY
- 49 F.3. HARDWARE PRODUCT WARRANTY DETAILS
- 50 F.4. SOFTWARE PRODUCT WARRANTY DETAILS
- 50 F.5. THIRD-PARTY SOFTWARE PRODUCT WARRANTY DETAILS