advertisement
6.29 MAC Address Table
Use the MAC address table to ensure the port security.
6.29.1 Static MAC Address
You can add a static MAC address that remains in the switch's address table regardless of whether the device is physically connected to the switch. This saves the switch from having to re-learn a device's MAC address when the disconnected or powered-off device is active on the network again. Via this interface, you can add / modify / delete a static MAC address.
Add the Static MAC Address
You can add static MAC address in the switch’s MAC table here. If the destination address and the VLAN ID of the packet meet the conditions set in the Static MAC
Addresses
table, the packet will be forwarded to the port only.
MAC Address: Enter the MAC address of the port that should permanently forward traffic, regardless of the device network activity.
Port No.: Pull down the selection menu to select the port number to which the traffic will be forwarded.
VLAN ID: Key in the VLAN ID to be the forwarding condition.
.
If you want to delete the MAC address from filtering table, select the MAC address and click
Delete
.
107
Static MAC Addresses interface
108
advertisement
Related manuals
advertisement
Table of contents
- 12 Introduction
- 12 Hardware Features
- 15 Software Features
- 18 Package Contents
- 19 Hardware Description
- 19 Physical Dimension
- 19 Front (LED) Panel
- 20 LED Indicators
- 22 Hardware Installation
- 22 Desktop Installation
- 22 Rack-mounted Installation
- 24 Cabling
- 27 Wiring the Power Inputs
- 28 Wiring the Fault Alarm Contact
- 29 Network Application
- 30 X-Ring Application
- 31 Coupling Ring Application
- 32 Dual Homing Application
- 33 Central Ring Application
- 34 X-RSTP Application
- 35 Console Management
- 35 Connecting to the Console Port
- 35 Pin Assignment
- 36 Login in the Console Interface
- 37 CLI Management
- 37 Commands Level
- 39 Web-Based Management
- 39 About Web-based Management
- 39 Preparing for Web Management
- 40 System Login
- 41 System Information
- 42 IP Configuration
- 44 DHCP Server
- 45 System configuration
- 46 Client Entries
- 47 Port and IP Bindings
- 48 Update Firmware
- 49 Restore Configuration
- 50 Backup Configuration
- 51 System Event Log
- 51 Syslog Configuration
- 53 System Event Log—SMTP Configuration
- 55 System Event Log—Event Configuration
- 57 Fault Relay Alarm
- 58 SNTP Configuration
- 62 IP Security
- 64 User Authentication
- 65 Advanced Configuration
- 65 Broadcast Storm Filter
- 67 Aging Time
- 68 Jumbo Frame
- 69 Port Statistics
- 71 Port Counters
- 74 Port Control
- 76 Port Trunk
- 76 Aggregator setting
- 78 Aggregator Information
- 82 State Activity
- 84 Port Mirroring
- 85 Rate Limiting
- 86 VLAN configuration
- 87 Port-based VLAN
- 90 802.1Q VLAN
- 95 Rapid Spanning Tree
- 95 System Configuration
- 97 Port Configuration
- 99 SNMP Configuration
- 99 System Configuration
- 101 Trap Configuration
- 102 SNMPV3 Configuration
- 105 QoS Configuration
- 107 IGMP Configuration
- 109 LLDP Configuration
- 110 X-Ring
- 113 X-RSTP
- 115 Security—802.1X/Radius Configuration
- 115 System Configuration
- 116 Port Configuration
- 117 Misc Configuration
- 118 MAC Address Table
- 118 Static MAC Address
- 120 MAC Filtering
- 121 All MAC Addresses
- 122 MAC Address Table—Multicast Filtering
- 124 Factory Default
- 125 Save Configuration
- 126 System Reboot
- 127 Troubles shooting
- 128 Appendix A — RJ-45 Pin Assignment
- 131 Appendix B — Command Sets
- 131 Commands Set List
- 131 System Commands Set
- 135 Port Commands Set
- 138 Trunk Commands Set
- 140 VLAN Commands Set
- 142 Spanning Tree Commands Set
- 145 QOS Commands Set
- 146 IGMP Commands Set
- 147 Mac / Filter Table Commands Set
- 149 SNMP Commands Set
- 152 Port Mirroring Commands Set
- 153 802.1x Commands Set
- 156 TFTP Commands Set
- 157 SystemLog, SMTP and Event Commands Set
- 159 SNTP Commands Set
- 161 X-Ring Commands Set
- 162 LLDP Command Set
- 163 Access Control List Command Set
- 165 X-RSTP Command Set