Specifications. Culligan Aqua-Cleer

Specifications

Typical System Flow Sequence . Particle Filter, Activated Carbon Filter, Reverse Osmosis Membrane, Specialty Filter,

Storage Tank, Polishing Filter, Dispensing Faucet

Particle Filter. . . . . . . . . . . . . . . . . 1, 2 or 3

Activated Carbon Filter . . . . . . . . Activated Carbon, Activated Carbon Block, Activated Carbon - Large

Reverse Osmosis Membrane . . . Culligan

®

Aqua-Cleer

®

Thin Film Composite

Production Rate

1

. . . . . . . . . . . . . Aqua-Cleer 30 Models 36 gpd (119 L/day)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . Aqua-Cleer 50 Models* 50 gpd (189 L/day)

Ratio of Product to Flush Flow

2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . Standard Applications 1:3 - 1:5 (Aqua-Cleer-30 models only)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . Soft Water Applications 1:1

Polishing Filter . . . . . . . .. . . . . . . Activated Carbon or Carbon Block

Specialty Cartridges

3

. . . . . . . . . . . . . . . . . . . . . . . . . . . . Arsenic Cartridge

. . . . . . . . . . . . . . . . . . . . . . . . . . . . Total Defense (MTBE, VOC Reduction)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . Perchlorate Cartridge*

1000 gallons

1000 gallons

1000 gallons

Dispensing Faucet . . . . . . . . . . . . Culligan Aqua-Cleer Faucet: Rotary Operation, Stainless Steel and Resin Flow Passages, with Built-in Siphon Break

. . . . . . . . . . . . . . . . . . . . . . . . . . . . Colors: Brushed Nickel, Polished Chrome or White

Storage Capacity

. . . . . . . . . . . . . . . . . . . . . . . . . . . . Standard Tank 2 gallons (7.5 L)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . Medium Tank 3 gallons (10.5 L)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . Large Tank 9 gallons (34 L)

Dimensions

. . . . . . . . . . . . . . . . . . . . . . . . . . . . Filter Assembly 13.8” W x 4.2” D x 15.5” H (35 cm W x 10.7 cm D x 39.4 cm H)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . Storage Tank • Std. 9” Diameter x 15”H (23 cm Diameter x 38 cm H)

• Med. 11” Diameter x 15”H (28 cm Diameter x 38 cm H)

• Lrg. 15.5” Diameter x 22”H (40 cm Diameter x 56 cm H)

1 Rating at 50 psi, 77°F, 500 mg/L TDS influent, without storage tank.

2 May vary with pressure. See “Replace Flow Control”, page 10, for all hard water applications and applications where TDS exceeds 1000 mg/L (ppm).

3 Arsenic and Perchlorate cartridge must be installed after the RO membrane and system must have a Performance

Indicator Device (PID) installed to track gallon usage.

Pressure

Temperature

Influent Water Characteristic

40 - 120 psi

33 - 100 ºF

Total Dissolved Solids (TDS)

1

0 - 2500 ppm (0 - 2500 mg/L) pH

Chlorine

2

Chloramine

Turbidity

Hardness

3

Iron

Bacterial Quality

5 - 10

0 - 3 ppm (0 - 3 mg/L)

0 - 3 ppm (0 - 3 mg/L)

0 - 10 NTU

0 - 10 gpg

0 - 1 ppm (0 - 1 mg/L)

Potable

Notes

1. See the “Performance & Technical Information” section for all applications where TDS exceeds 1000 ppm. A booster is strongly recommended to improve the reduction of TDS. Higher pressures will help maintain the membrane’s maximum rejection performance.

2. The reverse osmosis membrane used in these systems may be damaged by chlorine. These systems include activated carbon filters which protect the membranes by reducing chlorine. Influent chlorine should not exceed 3 mg/L.

3. A softener is strongly recommended for water over 10 gpg hard.

Installing a system without a softener on water with hardness higher than 10 gpg will reduce the life of the membrane.

4. Additional information on factors that affect RO performance can be found in the “Performance & Technical Information” section.

Table 1

* Cartridge not for sale in California.

2 Culligan

®

Aqua-Cleer

®

Drinking Water Systems