Operation Style. ACP Heavy Duty Commercial Compact Microwave Oven

2

3

4

5

Pads

1

Operation

STYLE 1

Interrupting Operation

Open oven door or press STOP/RESET pad to interrupt operation. Display continues to show countdown time. Close door and press START pad to resume oven operation.

Double Pad Programs

The oven control can be changed to store up to 100 cooking programs. See the

“User’s Options” section of this manual to change oven control.

Canceling Mistakes

If oven is not cooking, press STOP/RESET pad to clear display. If oven is cooking, press STOP/

RESET pad once to stop oven, then again to clear display.

If oven door is open and time shows in display, close oven door and press STOP/RESET pad to clear display.

Operating Preprogrammed Pads

From the factory, this oven can of store up to 10 preprogrammed cooking sequences in memory.

To heat using a preprogrammed sequence, press a numbered pad. Oven starts to heat automatically. Example: Heat using the third cooking sequence.

1. Open oven door, place food in oven, and close oven door.

• Display shows “READY”.

• If pad is not pressed in 60 seconds, open and close oven door again.

2. Press 3 pad.

• Oven operates and time counts down.

• Display shows cooking time, “STAGE 1”,

”COOKING”. Display shows “COOKING” only when microwave energy is present.

• If power level other than 100 percent power was programmed, display shows “STAGE 1”,

“COOKING” and “% MW POWER”.

• If additional cooking time is required, press preprogrammed pads before or after cooking cycle ends.

3. Oven stops cooking and oven signal sounds when cooking timing elapses.

Preprogrammed Times and Cook Level

All preprogrammed pads arrive set at full power.

To start a double pad cooking program, press 2 memory pads. For example, press pad 0 and pad 3 to start a cooking program.

Manual Time Entry

Manual Time Entry feature allows the operator to enter time and power levels, and heat without changing the preprogrammed pads.

Example: Heat for 30 seconds at 80% power.

1. Open oven door, place food in oven, and close door.

• Display shows “READY”. Fan and light operate.

• If pad is not pressed in 60 seconds, open and close oven door again.

2. Press TIME ENTRY pad.

• Display shows “00:00” and “READY”.

3. Press 3 and 0 pad to enter cooking time.

4. Press POWER LEVEL pad to change power level.

• Display shows “% MW POWER” and current power level if other than 100 percent power.

5. Press 8 pad to enter desired power level.

6. Press START pad.

• Oven operates and time counts down.

• Display shows cooking time, “COOKING”, “% MW

POWER”.

• Display shows “COOKING” only when microwave energy is present.

• If power level other than 100 percent power was programmed, display shows “COOKING” and “%

MW POWER”. Display counts down cooking time.

7. Oven stops cooking and oven signal sounds when cooking timing elapses and display shows “DONE”.

Times

10 sec.

20 sec.

30 sec.

45 sec.

1:00 min.

7

8

9

0

Pads

6

Times

1:30 min.

2:00 min.

3:00 min.

4:00 min.

5:00 min.

9

Memory Pads

From the factory, this oven can of store up to 10 cooking programs. Follow instructions below to program cooking times and power levels for customized cooking.

Example: Program third cooking sequence to heat for 30 seconds at 80% power.

1. Open oven door.

• Display shows “DOOR”.

• If door is closed or STOP/RESET pad is pressed before finishing programming sequence, oven exits programming mode.

2. Press and hold pad 1 for approximately 5 seconds.