advertisement
Commission the system
Turning on the system for the fi rst time
Before starting the system for the first time, check the following;
•
•
Check radar is physically clear to rotate
Leave a HD pulse radar in standby for 30 minutes before transmitting for the first time
•
•
Check all personnel are clear of radar beam (HD Radar)
Check all wiring is correctly connected. Apply power to the breaker
To turn ON the display, press and release the PWR key.
To place display in to Standby, press PWR key and select stand by.
To turn OFF the display, press and hold PWR key for three seconds.
If you turn the unit ON when no external equipment is connected you will be asked to run in simulator mode.
Operating the menu system
In this manual you will see few direct text references to keys, menus and menu entries, and few step-by-step descriptions. By using graphics we will guide you to the key and the required menu selections.
In the illustrations throughout the commissioning section the following symbols are used:
Single short press on illustrated key
MENU WIN
3 s
MENU WIN
Press and hold on illustrated key with time indication x2
MENU WIN
Press twice on illustrated key
Rotate rotary knob
Single short press on rotary knob
PLOT
MARK
GO TO
VESSEL
PLOT
MARK
GO TO
VESSEL
References to keys on the operator panel are written in boldface, e.g. WIN key.
For further information on the operating the system refer to the Operation Manual
Commission the system | 39
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 8 Introduction
- 8 About this manual
- 8 Conventions
- 8 Important safety and warning information
- 9 Check the parts
- 10 Overview
- 12 Installing the display
- 12 Mounting location
- 13 Panel mount
- 14 Bracket Mount
- 16 System architecture
- 16 Networking, Data Interfacing
- 16 SimNet / NMEA
- 16 Ethernet: (NETWORK ports)
- 17 Data Bridging
- 24 Wiring the NSE
- 25 Power
- 25 Connecting power
- 25 Power control
- 26 No Power Control
- 26 Auto Power on
- 26 Power Control Master
- 28 External alarm
- 29 SimNet
- 29 SimNet: The basics
- 30 Planning and installing a SimNet backbone
- 30 Power the SimNet network
- 33 Ethernet
- 34 Dual and Multi Station
- 35 NMEA0183 wiring
- 36 Video In
- 37 Video Out
- 38 Connecting BR24 Radar
- 39 Connecting HD Radar
- 40 Connecting BSM1 Broadband Echosounder
- 41 Commission the system
- 41 Turning on the system for the fi rst time
- 41 Operating the menu system
- 42 Commissioning checklist
- 43 System settings menu
- 43 Language
- 43 Time: Local Time, Time format, Date Format
- 43 Power Control
- 44 Echosounder setup
- 44 Depth offset
- 44 Water speed calibration
- 44 Echo sounder software version
- 45 Water speed averaging
- 45 Temperature calibration
- 45 Transducer type
- 45 Radar setup
- 45 Radar software version
- 46 Radar Transmit, Standby or off
- 47 Data setup
- 47 SimNet / NMEA2000 setup
- 47 Source selection (Auto select)
- 47 Source selection (Manual)
- 47 Group Source Selection (SIMRAD)
- 48 Group Source Selection (NONE)
- 48 Source selection advanced
- 50 Damping
- 50 Device List
- 51 Serial port setup
- 51 NMEA 0183 output
- 52 Vessel Setup
- 52 AIS own vessel
- 53 Diagnostics
- 53 NMEA2000 Diagnostics
- 53 USER Database UDB
- 54 Check GPS signal
- 54 System backup
- 54 Restore a backup
- 55 Software upgrades
- 55 Displaying current software version
- 55 NSE Display software version
- 55 Ethernet module software version
- 56 Additional NSE display upgrade steps
- 57 Screen capture
- 57 File transfer
- 58 Drawings
- 58 NSE8 Dimensions
- 59 NSE12 Dimensions
- 61 Spare parts
- 61 NSE Spare parts
- 62 Compatible BSM-1 Transducers
- 62 SimNet accessories
- 63 Ethernet cables (yellow)
- 63 Ethernet cables (RJ45)
- 63 Repeat screens
- 63 Video cables for repeat screens
- 64 Specifi cations
- 65 Supported NMEA0183 sentences
- 66 NMEA 2000 PGN List
- 66 NMEA 2000 PGN Receive
- 67 NMEA2000 PGN Transmit