EAN-8 2-Digit Supplemental Label ID. Datalogic MAGELLAN 8300, MAGELLAN 8404, MAGELLAN 8405, MAGELLAN 8400, MAGELLAN 8403, MAGELLAN 8302, MAGELLAN 8305, MAGELLAN 8301, MAGELLAN 8402, MAGELLAN 8304

Code 39 Enable

Code 39 Minimum Reads

Specifies the minimum number of consecutive times a Code 39 label must be decoded before it is accepted as a good read.

To set this feature:

1. Scan the SWITCH bar code.

2. Scan the bar code representing the desired option below or on the following pages. You’ll need to cover any unused bar codes on facing pages to ensure that the scanner reads only the bar code you intend to scan.

Complete the programming sequence by scanning the SWITCH bar code.

CODE 39 MINIMUM READS = 1

Product Reference Guide

CODE 39 MINIMUM READS = 2

6-287

Code 39 Minimum Reads — continued

Remember to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code you intend to scan.

CODE 39 MINIMUM READS = 3

6-288

CODE 39 MINIMUM READS = 4

Magellan

®

8300/8400

Pharmacode 39 Enable

Pharmacode 39 Enable

Enables/disables the ability of the scanner to decode Italian Pharmacode

39 labels.

To set this feature:

1. Scan the SWITCH bar code.

2. Scan either the enable or disable bar code below. You’ll need to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code you intend to scan.

3. Complete the programming sequence by scanning the SWITCH bar code.

PHARMACODE 39 = DISABLE

Product Reference Guide

PHARMACODE 39 = ENABLE

6-289

Pharmacode 39 Start Stop Character Transmission

Enables/ disables transmission of start and stop characters for Pharmacode

39.

To set this feature:

1. Scan the SWITCH bar code.

2. Scan either the enable or disable bar code below. You’ll need to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code you intend to scan.

3. Complete the programming sequence by scanning the SWITCH bar code.

PHARMACODE 39 START STOP CHARACTER TRANSMISSION = DISABLE

6-290

PHARMACODE 39 START STOP CHARACTER TRANSMISSION = ENABLE

Magellan

®

8300/8400

Pharmacode 39 Enable

Pharmacode 39 Check Character Transmission

Enables/disables transmission of Pharmacode 39 check character.

To set this feature:

1. Scan the SWITCH bar code.

2. Scan either the enable or disable bar code below. You’ll need to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code you intend to scan.

3. Complete the programming sequence by scanning the SWITCH bar code.

PHARMACODE 39 CHECK CHARACTER TRANSMISSION = DISABLE

PHARMACODE 39 CHECK CHARACTER TRANSMISSION = ENABLE

Product Reference Guide

6-291

Pharmacode 39 Label ID

This feature specifies a Pharmacode 39 label ID to be added to bar code data.

The programming feature, Label ID Control, designates whether the Label ID is transmitted as a prefix or suffix or if Label ID is disabled.

NOTE

To set this feature:

1. Scan the SWITCH bar code.

2. Scan the bar code,

SET PHARMACODE 39 LABEL ID

below. You’ll need to cover any unused bar codes on this and the facing page to ensure the scanner reads only the bar code you intend to scan.

3. Scan the appropriate digits from the keypad in

Appendix C that represent the desired Label ID characters; entered as two hex pairs. A table containing the

ASCII Character Set

and their corresponding

Hex Values is available in the inside back cover of this manual.

ASCII parameters must be input by scanning a pair of hexadecimal digits for each character. Thus, to set a two-character value of AB, bar codes containing the digits ‘4’, ‘1’, ‘4’, and ‘2’ must be scanned.

The selectable range for this option is any hex value from 00 to FF.

4. Complete the programming sequence by scanning the SWITCH bar code.

6-292

SET PHARMACODE 39 LABEL ID

Magellan

®

8300/8400

Code 128 Enable

Code 128 Enable

Enables/disables

1

the ability of the scanner to decode Code 128 labels.

To set this feature:

1. Scan the SWITCH bar code.

2. Scan either the enable or disable bar code below. You’ll need to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code you intend to scan.

3. Complete the programming sequence by scanning the SWITCH bar code.

CODE 128 = DISABLE

CODE 128 = ENABLE

1. Exception: The Code 128 symbology is always enabled with regard to scanning/reading the special C128 programming bar codes provided in this manual.

Product Reference Guide

6-293

Code 128 Transmit Function Characters

Enables/disables transmission of Code 128 function characters 1, 2, 3, and 4.

Disabled is the recommended setting for all interfaces.

NOTE

To set this feature:

1. Scan the SWITCH bar code.

2. Scan either the enable or disable bar code below. You’ll need to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code you intend to scan.

3. Complete the programming sequence by scanning the SWITCH bar code.

CODE 128 TRANSMIT FUNCTION CHARACTERS = DISABLE

6-294

CODE 128 TRANSMIT FUNCTION CHARACTERS = ENABLE

Magellan

®

8300/8400

Code 128 Enable

Convert Code 128 to Code 39

Enables/disables conversion of Code 128 labels to Code 39.

To set this feature:

1. Scan the SWITCH bar code.

2. Scan either the enable or disable bar code below. You’ll need to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code you intend to scan.

3. Complete the programming sequence by scanning the SWITCH bar code.

CONVERT CODE 128 TO CODE 39 = DISABLE

Product Reference Guide

CONVERT CODE 128 TO CODE 39 = ENABLE

6-295

Code 128 Label ID

This feature specifies a Code 128 label ID to be added to bar code data..

The programming feature, Label ID Control, designates whether the Label ID is transmitted as a prefix or suffix or if Label ID is disabled.

NOTE

To set this feature:

1. Scan the SWITCH bar code.

2. Scan the bar code,

SET CODE 128 LABEL ID

below. You’ll need to cover any unused bar codes on this and the facing page to ensure the scanner reads only the bar code you intend to scan.

3. Scan the appropriate digits from the keypad in

Appendix C that represent the desired Label ID characters; entered as two hex pairs. A table containing the

ASCII Character Set

and their corresponding

Hex Values is available in the inside back cover of this manual.

ASCII parameters must be input by scanning a pair of hexadecimal digits for each character. Thus, to set a two-character value of AB, bar codes containing the digits ‘4’, ‘1’, ‘4’, and ‘2’ must be scanned.

The selectable range for this option is any hex value from 00 to FF.

4. Complete the programming sequence by scanning the SWITCH bar code.

6-296

SET CODE 128 LABEL ID

Magellan

®

8300/8400

Code 128 Enable

Code 128 Length Control

This feature specifies whether variable-length or fixed-length decoding will be set for Code 128.

To set this feature:

1. Scan the SWITCH bar code.

2. Scan your selection from the bar codes below. You’ll need to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code you intend to scan.

3. Complete the programming sequence by scanning the SWITCH bar code.

You must now set the features

Code 128 Length 1

and

Code 128 Length

2

.

NOTE

CODE 128 LENGTH CONTROL = VARIABLE-LENGTH

Product Reference Guide

CODE 128 LENGTH CONTROL = FIXED-LENGTH

6-297

Code 128 Length 1

Length 1 is the minimum label length if in variable length mode, or the first fixed length if in fixed length mode (see

Code 128 Length Control

)

.

Length includes the barcode’s check and data characters.

To set this feature:

1. Scan the SWITCH bar code.

2. Scan the bar code,

SET CODE 128 LENGTH 1

below. You’ll need to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code you intend to scan.

3. Scan the appropriate digits from the keypad in

Appendix C that represent the desired label length. The selectable range for this option is

001 to 080. Pad all single and double digit numbers with leading zeroes to yield a three-digit entry (001-080).

4. Complete the programming sequence by scanning the SWITCH bar code.

6-298

SET CODE 128 LENGTH 1

Magellan

®

8300/8400

Code 128 Enable

Code 128 Length 2

Length 2 is the maximum label length if in variable length mode, or the second fixed length if in fixed length mode (see

Code 128 Length Control

)

. Length includes the barcode’s check and data characters.

To set this feature:

1. Scan the SWITCH bar code.

2. Scan the bar code,

SET CODE 128 LENGTH 2

below. You’ll need to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code you intend to scan.

3. Scan the appropriate digits from the keypad in

Appendix C that represent the desired label length. A setting of 000 will ignore this length (only one fixed length), otherwise, the selectable range for this option is 001 to 080. Pad all single and double digit numbers with leading zeroes to yield a three-digit entry (001-080).

4. Complete the programming sequence by scanning the SWITCH bar code.

Product Reference Guide

SET CODE 128 LENGTH 2

6-299

Code 128 Correlation

This feature enables/disables character correlation for Code 128.

To set this feature:

1. Scan the SWITCH bar code.

2. Scan your selection from the bar codes below. You’ll need to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code you intend to scan.

Complete the programming sequence by scanning the SWITCH bar code.

CODE 128 CORRELATION = DISABLE

6-300

CODE 128 CORRELATION = ENABLE

Magellan

®

8300/8400

Code 128 Enable

Code 128 Stitching

Enables/disables stitching for Code 128 labels. When parts of a Code 128 bar code are presented to the scanner with this feature enabled, the bar code parts will be assembled by the scanner’s software, and the data will be decoded if all bar code proofing requirements are met.

To set this feature:

1. Scan the SWITCH bar code.

2. Scan your selection from the bar codes below. You’ll need to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code you intend to scan.

Complete the programming sequence by scanning the SWITCH bar code.

CODE 128 STITCHING = DISABLE

Product Reference Guide

CODE 128 STITCHING = ENABLE

6-301

Code 128 Minimum Reads

Specifies the minimum number of consecutive times a Code 128 label must be decoded before it is accepted as a good read.

To set this feature:

1. Scan the SWITCH bar code.

2. Scan the bar code representing the desired option below or on the following pages. You’ll need to cover any unused bar codes on facing pages to ensure that the scanner reads only the bar code you intend to scan.

Complete the programming sequence by scanning the SWITCH bar code.

CODE 128 MINIMUM READS = 1

6-302

CODE 128 MINIMUM READS = 2

Magellan

®

8300/8400

Code 128 Enable

Code 128 Minimum Reads — continued

Remember to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code you intend to scan.

CODE 128 MINIMUM READS = 3

Product Reference Guide

CODE 128 MINIMUM READS = 4

6-303

EAN-128 Enable

Enables/disables the ability of the scanner to decode EAN-128 labels.

When disabled, EAN128 labels are transmitted in Code128 data format.

When enabled, EAN128 labels are transmitted in EAN128 data format

To set this feature:

1. Scan the SWITCH bar code.

2. Scan either the enable or disable bar code below. You’ll need to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code you intend to scan.

3. Complete the programming sequence by scanning the SWITCH bar code.

EAN-128 = DISABLE

6-304

EAN-128 = ENABLE

Magellan

®

8300/8400

EAN-128 Enable

EAN-128 Label ID

This feature specifies an EAN-128 label ID to be added to bar code data..

The programming feature, Label ID Control, designates whether the Label ID is transmitted as a prefix or suffix or if Label ID is disabled.

NOTE

To set this feature:

1. Scan the SWITCH bar code.

2. Scan the bar code,

SET EAN-128 LABEL ID

below. You’ll need to cover any unused bar codes on this and the facing page to ensure the scanner reads only the bar code you intend to scan.

3. Scan the appropriate digits from the keypad in

Appendix C that represent the desired Label ID characters; entered as two hex pairs. A table containing the

ASCII Character Set

and their corresponding

Hex Values is available in the inside back cover of this manual.

ASCII parameters must be input by scanning a pair of hexadecimal digits for each character. Thus, to set a two-character value of AB, bar codes containing the digits ‘4’, ‘1’, ‘4’, and ‘2’ must be scanned.

The selectable range for this option is any hex value from 00 to FF.

4. Complete the programming sequence by scanning the SWITCH bar code.

Product Reference Guide

SET EAN-128 LABEL ID

6-305

Interleaved 2 of 5 (I 2 of 5) Enable

Enables/disables the ability of the scanner to decode Interleaved 2 of 5 labels.

To set this feature:

1. Scan the SWITCH bar code.

2. Scan either the enable or disable bar code below. You’ll need to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code you intend to scan.

3. Complete the programming sequence by scanning the SWITCH bar code.

I 2 OF 5 = DISABLE

6-306

I 2 OF 5 = ENABLE

Magellan

®

8300/8400

Interleaved 2 of 5 (I 2 of 5) Enable

I 2 of 5 Check Character Calculation

Enables/disables calculation and verification of an optional Interleaved 2 of 5 check character.

If check character calculation is disabled, the risk is increased that a misread can occur. When disabled, any check characters in a bar code are treated as data characters.

NOTE

To set this feature:

1. Scan the SWITCH bar code.

2. Scan either the enable or disable bar code below. You’ll need to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code you intend to scan.

3. Complete the programming sequence by scanning the SWITCH bar code.

I 2 of 5 CHECK CHARACTER CALCULATION = DISABLE

Product Reference Guide

I 2 of 5 CHECK CHARACTER CALCULATION = ENABLE

6-307

I 2 of 5 Check Character Transmission

Enables/disables transmission of an optional Interleaved 2 of 5 check character.

This feature applies only when

I 2 of 5 Check Character Calculation

is enabled.

NOTE

To set this feature:

1. Scan the SWITCH bar code.

2. Scan either the enable or disable bar code below. You’ll need to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code you intend to scan.

3. Complete the programming sequence by scanning the SWITCH bar code.

I 2 of 5 CHECK CHARACTER TRANSMISSION = DISABLE

6-308

I 2 of 5 CHECK CHARACTER TRANSMISSION = ENABLE

Magellan

®

8300/8400

Interleaved 2 of 5 (I 2 of 5) Enable

I 2 of 5 Label ID

This feature specifies an I 2 of 5 label ID to be added to bar code data..

The programming feature, Label ID Control, designates whether the Label ID is transmitted as a prefix or suffix or if Label ID is disabled.

NOTE

To set this feature:

1. Scan the SWITCH bar code.

2. Scan the bar code,

SET I 2 of 5 LABEL ID

below. You’ll need to cover any unused bar codes on this and the facing page to ensure the scanner reads only the bar code you intend to scan.

3. Scan the appropriate digits from the keypad in

Appendix C that represent the desired Label ID characters; entered as two hex pairs. A table containing the

ASCII Character Set

and their corresponding

Hex Values is available in the inside back cover of this manual.

ASCII parameters must be input by scanning a pair of hexadecimal digits for each character. Thus, to set a two-character value of AB, bar codes containing the digits ‘4’, ‘1’, ‘4’, and ‘2’ must be scanned.

The selectable range for this option is any hex value from 00 to FF.

4. Complete the programming sequence by scanning the SWITCH bar code.

Product Reference Guide

SET I 2 of 5 LABEL ID

6-309

I 2 of 5 Length Control

This feature specifies whether variable-length or fixed-length decoding will be set for I 2 of 5.

To set this feature:

1. Scan the SWITCH bar code.

2. Scan your selection from the bar codes below. You’ll need to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code you intend to scan.

3. Complete the programming sequence by scanning the SWITCH bar code.

You must now set the features

I 2 of 5 Length 1

and

I 2 of 5 Length 2

.

NOTE

I 2 OF 5 LENGTH CONTROL = VARIABLE-LENGTH

6-310

I 2 OF 5 LENGTH CONTROL = FIXED-LENGTH

Magellan

®

8300/8400

Interleaved 2 of 5 (I 2 of 5) Enable

I 2 of 5 Length 1

Length 1 is the minimum label length if in variable length mode, or the first fixed length if in fixed length mode (see

I 2 of 5 Length Control

)

.

Length includes the barcode’s check and data characters.

To set this feature:

1. Scan the SWITCH bar code.

2. Scan the bar code,

SET I 2 of 5 LENGTH 1

below. You’ll need to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code you intend to scan.

3. Scan the appropriate digits from the keypad in

Appendix C that represent the desired label length. The selectable range for this option is

002 to 050, even numbers only. Pad all single and double digit numbers with leading zeroes to yield a three-digit entry (002-050).

4. Complete the programming sequence by scanning the SWITCH bar code.

Product Reference Guide

SET I 2 of 5 LENGTH 1

6-311

I 2 of 5 Length 2

Length 2 is the maximum label length if in variable length mode, or the second fixed length if in fixed length mode (see

I 2 of 5 Length Control

)

.

Length includes the barcode’s check and data characters.

To set this feature:

1. Scan the SWITCH bar code.

2. Scan the bar code,

SET I 2 of 5 LENGTH 2

below. You’ll need to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code you intend to scan.

3. Scan the appropriate digits from the keypad in

Appendix C that represent the desired label length. A setting of 000 will ignore this length (only one fixed length), otherwise, the selectable range for this option is 002 to 050, even numbers only. Pad all single and double digit numbers with leading zeroes to yield a three-digit entry

(002-050).

4. Complete the programming sequence by scanning the SWITCH bar code.

6-312

SET I 2 of 5 LENGTH 2

Magellan

®

8300/8400

Interleaved 2 of 5 (I 2 of 5) Enable

I 2 of 5 Correlation

This feature enables/disables character correlation for I 2 of 5.

To set this feature:

1. Scan the SWITCH bar code.

2. Scan your selection from the bar codes below. You’ll need to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code you intend to scan.

Complete the programming sequence by scanning the SWITCH bar code.

I 2 of 5 CORRELATION = DISABLE

Product Reference Guide

I 2 of 5 CORRELATION = ENABLE

6-313

I 2 of 5 Stitching

Enables/disables stitching for I 2 of 5 labels. When parts of an I 2 of 5 bar code are presented to the scanner with this feature enabled, the bar code parts will be assembled by the scanner’s software, and the data will be decoded if all bar code proofing requirements are met.

To set this feature:

1. Scan the SWITCH bar code.

2. Scan your selection from the bar codes below. You’ll need to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code you intend to scan.

3. Complete the programming sequence by scanning the SWITCH bar code.

I 2 of 5 Stitching operates using fixed lengths ONLY.

I 2 of 5 Length 1

and/or

I 2 of 5 Length 2

must be properly configured for stitching to work.

NOTE

I 2 OF 5 STITCHING = DISABLE

6-314

I 2 OF 5 STITCHING = ENABLE

Magellan

®

8300/8400

Interleaved 2 of 5 (I 2 of 5) Enable

I 2 of 5 Minimum Reads

Specifies the minimum number of consecutive times an I 2 of 5 label must be decoded before it is accepted as a good read.

To set this feature:

1. Scan the SWITCH bar code.

2. Scan the bar code representing the desired option below or on the following pages. You’ll need to cover any unused bar codes on facing pages to ensure that the scanner reads only the bar code you intend to scan.

Complete the programming sequence by scanning the SWITCH bar code.

I 2 of 5 MINIMUM READS = 1

Product Reference Guide

I 2 of 5 MINIMUM READS = 2

6-315