REMOTE SERVICE. SRAM Reba 2011

32

REMOTE SERVICE

(PUSHLOC - POPLOC ADJUST - POPLOC)

INTRODUCTION

Damper service for forks equipped with remote lockouts will require cable and housing removal and installation. Also, periodic replacement of the cable and housing is recommended for optimal remote performance.

CABLE REMOVAL INSTRUCTIONS

FORK LOCKOUT ANATOMY Spool Housing stop Cable end slot

Pinch bolt

1.

2.

3.

4.

5.

PushLoc only:

Push the remote lever until it returns toward you.

PopLoc and PopLoc Adjust only: Press the button next to the remote lever to set the lever to the fully released, or "Unlocked" position.

BlackBox Motion Control, Lyrik RLR, and

Lyrik RLR+ only: Use a 2 mm hex wrench to loosen the cable pinch bolt on the spool and pull the cable out of the cable end slot. Use pliers to remove the cable end.

OR

Motion Control only: Use a 2 mm hex wrench to loosen the cable pinch bolt on the spool. Use pliers to remove the cable end.

PushLoc only:

Push the remote lever to the

"Locked Out" position. Use your finger to open the cable hatch cover (labeled

CC, for Cable

Change). Push the cable through the spool on the fork until the cable head is far enough out of the lever to access.

PopLoc and PopLoc Adjust only: Push the cable through the spool until the cable head is far enough out of the lever to grab onto.

Pull the cable head to remove the cable completely from the remote system.

If replacing the cable housing, detach the cable housing and end caps from the lever and the cable housing stop on the fork.

1

2

3

PushLoc

BlackBox

PushLoc

PopLoc/PopLoc

Adjust

Motion Control

Fixing port

BlackBox only

PushLoc

PopLoc/PopLoc

Adjust

33

CABLE INSTALLATION INSTRUCTIONS

6.

7.

8.

9.

10.

If replacing the cable housing, attach the new housing and end caps to the remote lever and the cable housing stop on the fork. Be sure to use compressionless (shift) housing cut to an adequate length to accomodate for travel change and suspension movement.

PopLoc and PopLoc Adjust only

: Push the release button to verify the remote is in the

"Unlocked" position.

PopLoc Adjust only: Turn the blue compression adjustment dial counter-clockwise until it stops.

Insert the tip of a new shifter cable into the port on the lever and feed the cable through the housing and the cable housing stop on the fork.

Pull the cable until the cable head is seated completely in the remote lever.

PushLoc only: Once the cable head is seated in the remote lever body, close the cable hatch cover and push the lever to return it to the

"Unlocked"

position.

BlackBox Motion Control, Lyrik RLR, and

Lyrik RLR+ only: Wrap the cable around the spool and insert it through the cable fixing port.

While pulling the cable firmly, use a 2 mm hex wrench to tighten the cable pinch bolt to 0.9 N·m

(8 in-lb). Cut the excess cable, leaving 30 mm protruding from the cable fixing port. Cap the end of the cable with a non-flanged, or "road style" cable end. Tuck the cable end into the cable end slot in the spool.

OR

Motion Control only: Wrap the cable around the spool. While pulling the cable firmly, use a 2 mm hex wrench to tighten the cable pinch bolt to

0.9 N·m (8 in-lb). Cut the excess cable and cap it with a cable end.

7

8

9

10

PopLoc/PopLoc

Adjust

PopLoc/PopLoc

PushLoc

Adjust

PopLoc/PopLoc

Adjust

PushLoc

BlackBox BlackBox

PushLoc

BlackBox

Motion Control Motion Control

www.sram.com

WORLD HEADQUARTERS

SRAM, LLC

1333 N. Kingsbury St., 4th Fl

Chicago, Il 60642

Phone +1-312-664-8800

Fax +1-312-664-8826

EUROPEAN HEADQUARTERS

SRAM Europe

Paasbosweg 14-16

3862ZS Nijkerk

The Netherlands

Phone +31-33-450-6060

Fax +31-33-457-0200

ASIAN HEADQUARTERS

SRAM Taiwan

No. 1598-8 Chung Shan Rd

Shen Kang Hsiang, Taichung

County 429 Taiwan R.O.C.

Phone +886-4-2564-3678

FAX +886-4-2561-3686