Operator manual Shark KG

OPERATOR’S MANUAL
M
KG-252437
KG-262637
KG-313137
KG-403637
ORDER #
1.107-238.0
1.107-239.0
1.107-240.0
1.107-241.0
o locate your local Shark Commercial Pressure Washer Dealer nearest you,
visit www.shark-pw.com
T
9 9 CONTENTS
Important Safety Information ................................................................4-6
Component Identification ......................................................................... 7
Assembly Instructions .............................................................................. 8
Operating Instructions.........................................................................9-10
Detergent and General Operating Techniques ...................................... 11
Shut Down and Clean-Up ...................................................................... 12
Storage .................................................................................................. 12
Troubleshooting ................................................................................13-14
Preventive Manteinance ........................................................................ 15
Hose and Spray Gun Assembly and Parts list ....................................... 16
Oil Change Record ................................................................................ 17
Serial Number ______________________________
Date of Purchase ___________________________
The model and serial numbers will be found on a decal attached
to the pressure washer. You should record both serial number and
date of purchase and keep in a safe place for future reference.
3
! "#v.
02/14
PRESSURE WASHER
OPERATOR’S MANUAL
INTRODUCTION & IMPORTANT SAFETY INFORMATION
Thank you for purchasing this Pressure Washer.
We reserve the right to make changes at any time
without incurring any obligation.
WARNING
Owner/User Responsibility:
The owner and/or user must have an understanding of
the manufacturer’s operating instructions and warnings
before using this pressure washer. Warning information
should be emphasized and understood. If the operator
is not fluent in English, the manufacturer’s instructions
and warnings shall be read to and discussed with
the operator in the operator’s native language by the
purchaser/owner, making sure that the operator comprehends its contents.
Owner and/or user must study and maintain for future
reference the manufacturers’ instructions.
The operator must know how to stop the machine
quickly and understand the operation of all controls.
Never permit anyone to operate the engine without
proper instructions.
SAVE THESE INSTRUCTIONS
E:; <;OTECTION
MUST BE WORN
WARNING
U=1 7ROTECTIVE
EYE WEAR
AND CLOTHING
WHEN OPERATING
THIS EQUIPMENT.
WARNING
When ordering parts, please specify model and
serial number. Use only identical replacement parts.
This machine is to be used only by trained operators.
IMPORTANT SAFETY
INFORMATION
R125 671R2TOR’S
MANUAL THOROUGHLY
PRIOR TO USE.
WARNING: To reduce the risk of
injury, read operating instructions carefully before using.
1. Read owner's manual thoroughly. Failure to follow instructions could cause malfunction of the machine and
result in death, serious bodily
injury and/or property damage.
2. Know how to stop the machine and bleed pressure
quickly. Be thoroughly familiar with the controls.
3. Stay alert — watch what you are doing.
WARNING
ARNING: Keep wand, hose, and
water spray away from electric
wiring or fatal electric shock may
result.
W
4.
K117 8ATER
SPRAY AWAY FROM
ELECTRICAL WIRING.
All installations must comply
with local codes. Contact
your electrician, plumber,
utility company or the selling
distributor for specific details.
WARNING: High pressure spray
can cause paint chips or other
particles to become airborne
and fly at high speeds. To avoid
personal injury, eye, hand and
foot safety devices must be
worn.
5. Eye, hand, and foot protection must be worn when
using this equipment.
6. Keep operating area clear of all persons.
This manual should be considered a permanent
part of the machine and should remain with it if
machine is resold.
4
ARNING:This machine exceeds
85 db appropriate ear protection
must be worn.
W
R>=K 6? 1@7A6=>6BC
OPERATE ONLY WHERE
OPEN FLAME OR TORCH
IS PERMITTED
WARNING
RISK OF FIRE.
DO NOT ADD FUEL
WHEN OPERATING
MACHINE.
ARNING: Flammable liquids
can create fumes which can ignite, causing property damage
or severe injury.
W
WARNING: Risk of explosion —
Operate only where open flame
or torch is permitted.
ARNING: Risk of fire — Do not
add fuel when the product is
operating or still hot.
W
WARNING: Do not use gasoline
crankcase draining or oil containing gasoline, solvents or
alcohol. Doing so will result in
fire and/or explosion.
WARNING: Risk of fire — Do not
Spray flammable liquids.
WARNING: This product contains chemicals known
to the state of California to cause cancer and birth
defects or other reproductive harm. Operation of
this equipment may create sparks that can start
fires around dry vegetation. A spark arrestor may
be required. The operator should contact: Local
fire agencies for laws or regulations relating to fire
prevention requirements.
7. Allow engine to cool for 1-2 minutes before refueling. If any fuel is spilled, make sure the area is
dry before testing the spark plug or starting the
engine. (Fire and/or explosion may occur if this is
not done.)
$%&'()*$+%' , -. , /0v.
02/14
WARNING: Risk of injury. Disconnect battery
ground terminal before servicing.
8. When in use , do not place machine near flammable
objects as the engine is hot.
9. Oil burning appliances shall be installed only in
locations where combustible dusts and flammable
gases or vapors are not present. Do not store or
use gasoline near this machine.
10. Use No. 1 or No. 2 heating oil (ASTM D306) only.
NEVER use gasoline in your fuel oil tank. Gasoline
is more combustible than fuel oil and could result
in a serious explosion. NEVER use crankcase or
waste oil in your burner. Fuel unit malfunction could
result from contamination.
11. Do not confuse gasoline and fuel oil tanks. Keep
proper fuel in proper tank.
WARNING
jklm no kpqrjY.
ARNING: Risk of injury. Hot
surfaces can cause burns. Use
only designated gripping areas
of spray gun and wand. Do not
place hands or feet on non-insulated areas of the pressure
washer.
X
HOT SURFACES
CAN CAUSE BURNS
12. Transport/Repair with fuel tank EMPTY or with fuel
shut-off valve OFF.
stUTION: Hot discharge fluid.
Do not touch or direct discharge
stream at persons.
HOT DISCHARGE FLUID:
DO NOT TOUCH OR
DIRECT DISCHARGE
STREAM AT PERSONS.
WARNING: This machine produces hot water and must have
insulated components attached
to protect the operator.
WARNING
ARNING: Grip cleaning wand
securely with both hands before
starting. Failure to do this could
result in injury from a whipping
wand.
14. Never make adjustments on
machine while in operation.
X
TRIGGER GUN KICKS
BACK - HOLD WITH
BOTH HANDS
15. Be certain all quick coupler fittings are secured
before using pressure washer.
WARNING
YZ[\ ]^ Z_`abcZ]_
OR SEVERE INJURY
TO PERSONS. KEEP
CLEAR OF NOZZLE.
WARNING
ARNING: High pressure developed by these machines will
cause personal injury or equipment damage. Keep clear of
nozzle. Use caution when operating. Do not direct discharge
stream at people, or severe injury or death will result.
X
OPERATOR’S MANUAL
Gasoline engines on mobile or portable equipment
shall be refueled:
a. outdoors;
b. with the engine on the equipment stopped;
c. with no source of ignition within 10 feet of
the dispensing point; and
d. with an allowance made for expansion of the
fuel should the equipment be exposed to a
higher ambient temperature.
In an overfilling situation, additional precautions are
necessary to ensure that the situation is handled
in a safe manner.
PRESSURE WASHER
TANT SAFETY INFORMATION
efghi
WARNING: Protect machine from
freezing.
16. To keep machine in best
operating conditions, it is
important you protect machine
from freezing. Failure to protect
dYOTECT FROM
machine from freezing
FREEZING
could cause malfunction of the
machine and result in death,
serious bodily injury, and/or property damage. Follow storage instructions specified in this manual.
17. Inlet water must be clean fresh water and no hotter
then 90°F.
WARNING WARNING: Risk of asphyxiation.
Use this product only in a well
ventilated area.
18. Avoid installing machines
in small areas or near exhaust fans. Adequate oxYZ[\ ]^
ASPHYXIATION. USE
ygen is needed for comTHIS PRODUCT ONLY IN
bustion or dangerous carA WELL
VENTILATED AREA.
bon monoxide will result.
19. Manufacturer will not be liable for any changes
made to our standard machines or any components
not purchased from us.
20. The best insurance against an accident is precaution and knowledge of the machine.
13. To reduce the risk of injury, close supervision is
necessary when a machine is used near children.
Do not allow children to operate the pressure
washer. This machine must be attended during
operation.
DFGHIJLDNFH O PQ O SVv.
5
02/14
PRESSURE WASHER
OPERATOR’S MANUAL
IMPORTANT SAFETY INFORMATION
WARNING
ƒ„…† ‡ˆ „‰Š‹ƒY FROM
FALLS WHEN USING
LADDER.
WARNING: Be extremely careful
when using a ladder, scaffolding
or any other relatively unstable
location. The cleaning area
should have adequate slopes
and drainage to reduce the possibility of a fall due to slippery
surfaces.
21. Do not allow acids, caustic or abrasive fluids to pass
through the pump.
22. Never run pump dry or leave spray gun closed
longer than 1-2 minutes.
23. Machines with shut-off spray gun should not be
operated with the spray gun in the off position for
extensive periods of time as this may cause damage to the pump.
24. Protect discharge hose from vehicle traffic and
sharp objects. Inspect condition of high pressure
hose before using or bodily injury may result.
25. Before disconnecting discharge hose from water
outlet, turn burner off and open spray gun to allow water to cool below 100° before stopping the
machine. Then open the spray gun to relieve pressure. Failure to properly cool down or maintain the
heating coil may result in a steam explosion.
26. Do not overreach or stand on unstable support.
Keep good footing and balance at all times.
27. Do not operate this machine when fatigued or under
the influence of alcohol, prescription medications,
or drugs.
28. In oil burning models, use only kerosene, No. 1
home heating fuel, or diesel. If diesel is used, add
a soot remover to every tankful.
29. This pressure washer is equipped with pneumatic
tires which may not be fully inflated due to shipping
and storage. Please check the air pressure of each
tire before use:
a. Remove the valve cap from the tire.
b. Attach a bicycle pump and inflate the tire to a
maximum pressure of 25 PSI.
o Note: If a compressor must be used, follow the
compressor manufacturer's guidelines to limit the
output pressure so as not to exceed 25 PSI.
c. Replace the valve cap to the tire valve and tighten
firmly. Tire pressure should not exceed 25 PSI.
ŒŽŽw the maintenance instructions
specified in the manual.
‚
uvwxyz{u|vx } ~ } €v.
02/14
PRESSURE WASHER
COMPONENT IDENTIFICATION
­®¯°®­
160cc, 190cc
Hose and Gun
Hanger
Starter Grip
¤¥¦§ ¨§§©
Spray Gun
Hose
Detergent
Pump
Protector
¡¢£ ter
OPERATOR’S MANUAL
Garden Hose
(not included)
(313137 &
403637 models)
Grip
Trigger
±²°±³
Inlet
Screen
PUMP
Detergent
Bucket
(not included)
Hose and Gun
Hanger
ENGINE
196cc, 208cc
Hose
Detergent
ª«¬¬¬
Straight
Through Wand
Pump
Garden Hose
(not included)
Pump
Protector
œžŸ
Inlet
Screen
High Pressure
Hose
Pressure
Nozzle
— Develops high pressure.
Starter Grip— Used for starting the engine manually.
Spray Gun — Controls the application of water and
detergent onto cleaning surface with trigger device.
Includes safety latch.
Unloader valve— Safety device which allows pressure
tu be released when spray gun is closed
Detergent Injector — Allows you to siphon and mix
detergents.
High Pressure Hose — Connect one end to water
pump discharge nipple and the other end to spray
gun.
Pump Protector — Cycles fresh cool water through
pump when recirculating water reaches 140°F.
Note: If trigger on spray gun is released for more
than 1-2 minutes, water will leak from valve. Warm
water will discharge from pump protector onto
floor. This system prevents internal pump damage.
Wand — Must be connected to the spray gun.
7
‘’“”•–’ — ˜™ — š›v.
02/14
PRESSURE WASHER
OPERATOR’S MANUAL
ASSEMBLY INSTRUCTIONS
Knob
Alignment
Holes
Gun &
Hose
Hanger
Nut
Frame
Assy.
Handle
Attach the handle to the
frame of the pressure washer. Note:
It may be necessary to move the
handle supports from side to side
in order to align the handle so it will
slide over the frame supports.
ÂÃÄÅ ÆÇ
Spray
Gun
Bolt
STEP 2: Insert the carriage bolt
through the holes from the back of
the unit and attach a knob from the
front of the machine. Tighten Knobs
with by hand.
High
Pressure Hose
Washer
STEP 3: Attach the Gun & hose
hanger and insert nuts and washers from inside. Tighten nuts. (Hose
hanger position: see "COMPONENT IDENTIFICATION")
Pressure
Nozzle
Wand
Coupler
Spray
Gun
ÈÉÊety
Wand
Latch
STEP 4: Attach the high pressure
ÂÃÄÅ ËÇ Attach wand to spray gun/
hose to the spray gun using teflon
wand. Tighten both.
tape (not included) on hose threads.
Pressure
Nozzle
Discharge
Nipple
Wand
Coupler
High
Pressure
Hose
STEP 7: Connect the high pressure
hose to the discharge nipple.
Garden
Hose
Pump
Water Inlet
Á
STEP 9: Check inlets filters, remove debris, then connect the
garden hose to pump water inlet.
CAUTION: Do not run the pump
without water or pump damage
will result.
´µ¶·¸¹º´»µ· ¼ ½¾ ¼ ¿Àv.
Cold
Water
Source
Garden
Hose
Coupler
Collar
STEP 6: Release the coupler collar
and push the nozzle until the collar
clicks. Pull the nozzle to make sure
it is seated properly.
STEP 5: Pull spring-loaded collar
of the wand coupler back to insert
your choice of pressure nozzle.
02/14
STEP 8: Connect garden hose to
the cold water source.
ÛÜÝ ÞÜßàáÜâk
PRESSURE WASHER
OPERATING INSTRUCTIONS
OPERATOR’S MANUAL
UTION! Engine Shipped without oil. Before starting engine, fill
with oil included. Do not over-fill.
ÙÚ
STEP 1: Check engine oil level. Oil level should be level with the bottom
of the oil filler neck. Be sure the machine is level when checking the oil
level. (Refer to the engine's operating manual included with machine.)
We recommend that the oil be changed after the first 5 hours of use, then
once every 50 hours. Note: Improper oil levels will cause low oil sensor
to shut off engine. IMPORTANT! Do not run engine with high or low
oil levels as this will cause engine damage.
Cold
Water
Source
Gas
Tank
Garden
Hose
STEP 2: Fill gas tank with unleaded
gasoline. Do not use leaded gasoline.
STEP 3: Connect garden hose
to the cold water source and turn
water on completely. Never use
hot water.
STEP 4: Trigger the spray gun to
eliminate trapped air then wait for
a steady flow of water to emerge
from the spray nozzle.
Choke
Lever
ãäåæç
Fuel
Valve
Fuel
Valve
STEP 5: Rotate the fuel shut-off valve to the "On"
position. Slide the fuel valve lever to the "ON" position.
When the engine is not in use, leave the fuel valve in
the "OFF" position.
STEP 6: Move the choke lever to the "Choke" position (on a warm engine, leave the choke lever in the
run position). Move the choke lever to the "Closed"
position. To restart a warm engine, leave the choke
lever in the "Open" position.
ÌÍÎÏÐÑÒÌÓÍÏ Ô ÕÖ Ô ×Øv.
02/14
9
PRESSURE WASHER
OPERATOR’S MANUAL
OPERATING INSTRUCTIONS
÷øù÷úú
Switch
STEP 7: Turn the engine switch to "On" position.
On Briggs engines, move the throttle lever to "Fast"
position, shown on the engine as a rabbit.
STEP 8: Pull the starter grip. If the engine fails to start
after 2 pulls, squeeze the trigger gun to release pressure and repeat step. Return starter gently. After the
engine warms up enough to run smoothly, move choke
to run position and throttle to fast position.
CAUTION: Small engines may kick back. Do not
hold pull starter grip tightly in hand.
NOZZLES
Safety
Latch
WARNING! Never replace
nozzles without engaging the
safety latch on the spray gun
trigger.
The five color-coded quick connect nozzles provide a wide array of
spray widths from 0° to 40° and are easily accessible when placed in the
convenient rubber nozzle holder, which is provided on the front of the
machine.
NOTE: For a more gentle rinse, select the white 40° or green 25° nozzle.
To scour the surface, select the yellow 15° or red 0° nozzle. To apply detergent select the black nozzle.
õö
èéêëìíîèïéë ð ñò ð óôv.
02/14
WARNING
WARNING: Some detergents
may be harmful if inhaled or
ingested, causing severe nausea, fainting or poisoning. The
harmful elements may cause
property damage or severe
injury.
Detergent
Injector
Discharge
Nipple
Soap
Nozzle
High
Pressure
Hose
THERMAL PUMP PROTECTION
If you run the engine on your pressure washer for
1-2 minutes without pressing the trigger on the spray
gun, circulating water in the pump can reach high
temperatures. When the water reaches this temperature, the pump protector engages and cools the pump
by discharging the warm water onto the ground. This
thermal device prevents internal damage to the pump.
CLEANING TIPS
Pre-rinse cleaning surface with fresh water. Place detergent suction tube directly into cleaning solution and
apply to surface at low pressure (for best results, limit
your work area to sections approximately 6 feet square
and always apply detergent from bottom to top). Allow
detergent to remain on surface 1-3 minutes. Do not allow detergent to dry on surface. If surface appears to
be drying, simply wet down surface with fresh water.
If needed, use brush to remove stubborn dirt. Rinse
at high pressure from top to bottom in an even sweeping motion keeping the spray nozzle approximately
1 foot from cleaning surface. Use overlapping strokes
as you clean and rinse any surface. For best surface
cleaning action spray at a slight angle.
OPERATOR’S MANUAL
STEP 1: Connect detergent injector to discharge nipple
on machine. Connect high pressure hose to injector
with quick coupler. (Check to make sure locking coupler
sleeves are in proper position before applying water
pressure).
TECHNIQUES
PRESSURE WASHER
D
D Recommendations:
STEP 2: Use detergent designed
specifically for pressure washers.
Household detergents could damage
the pump. Prepare detergent solution
as required by manufacturer. Fill a
container with pressure washer detergent. Place filter end of detergent
suction tube into detergent container.
STEP 3: With safety latch on spray gun engaged,
secure black detergent nozzle into
quick coupler. NOTE: Detergent
cannot be applied using red, yellow,
green or white nozzles.
STEP 4: With the engine running,
pull trigger to operate machine. Liquid
detergent is drawn into the machine and mixed with
water. Apply detergent to work area. Do not allow
detergent to dry on surface.
IMPORTANT: You must flush the detergent injection system after each use by placing the suction
tubeinto a bucket of clean water, then run the
pressure washer in low pressure for 1-2 minutes.
9
ûüýþÿ
• Before cleaning any surface, an inconspicuous
area should be cleaned to test spray pattern and
distance for maximum cleaning results.
• If painted surfaces are peeling or chipping, use
extreme caution as pressure washer may remove
the loose paint from the surface.
• Keep the spray nozzle a safe distance from the
surface you plan to clean. High pressure wash a
small area, then check the surface for damage. If
no damage is found, continue to pressure washing.
CAUTION - Never use:
• Bleach, chlorine products and other corrosive
chemicals
• Liquids containing solvents (i.e., paint thinner,
gasoline, oils)
• Tri-sodium phosphate products
• Ammonia products
• Acid-based products
These chemicals will harm the machine and will damage the surface being cleaned.
RINSING
It will take a few seconds for the detergent to clear.
Apply safety latch to spray gun. Remove black soap
nozzle from the quick coupler. Select and install the
desired high pressure nozzle. NOTE: You can also stop
detergent from flowing by simply removing detergent
siphon tube from bottle.
v. 02/14
û üþ
11
PRESSURE WASHER
OPERATOR’S MANUAL
SHUTTING DOWN AND CLEAN-UP
On-Off
Switch
STEP 1: Remove detergent suction tube from container and insert
into one gallon of fresh water. Slide
nozzle forward for low pressure or
to connect black detergent nozzle.
Pull trigger on spray gun and siphon
water for one minute.
STEP 2: Turn off the engine.
Pump
Water Inlet
STEP 4: Press trigger to release water
pressure.
STEP 3: Turn off water
supply.
Discharge
Nipple
STEP 5: Disconnect the garden
hose from the water inlet on the
machine.
STEP 6: Disconnect the high
pressure hose from discharge
nipple.
Sety
Latch
STEP 7: Engage
the spray gun safety lock.
STORAGE
CAUTION: Always store your pressure washer in a
location where the temperature will not fall below
32°F (0°C). The pump in this machine is susceptible
to permanent damage if frozen. FREEZE DAMAGE
IS NOT COVERED BY WARRANTY.
1. Stop the pressure washer, squeeze spray gun trigger to release pressure.
2. Detach water supply hose and high pressure hose.
3. Turn on the machine for a few seconds, until remaining water exits. Turn engine off immediately.
4. Drain the gas and oil from the engine.
5. Do not allow high pressure hose to become kinked.
6. Store the machine and accessories in a room which
does not reach freezing temperatures.
CAUTION: Failure to follow the above directions will
result in damage to your pressure washer.
When the pressure washer is not being operated or is
being stored for more than one month, follow these
instructions:
1
1. Replenish engine oil to upper level.
2. Drain gasoline from fuel tank, fuel line, fuel valve
and carburetor.
3. Pour about one teaspoon of engine oil through
the spark plug hole, pull the starter grip several
times and replace the plug. Then pull the starter
grip slowly until you feel increased pressure which
indicates the piston is on its compression stroke and
leave it in that position. This closes both the intake
and exhaust valves to prevent rusting of cylinder.
4. Cover pressure washer and store in a clean, dry
place that is well ventilated away from open flame
or sparks. NOTE: The use of a fuel additive, such as
STA-BIL®, or an equivalent, will minimize the formulation of fuel deposits during shortage. Such additives
may be added to the gasoline in the fuel tank of the
engine, or to gasoline in a storage container.
After Extended Storage
CAUTION: Prior to restarting, thaw out
any possible ice from pressure washer
hoses, spray gun or wand.
Engine Maintenance
During the winter months, rare atmospheric conditions
may develop which will cause an icing condition in the
carburetor. If this develops, the engine may run rough,
lose power and may stall. This temporary condition can
be overcome by deflecting some of the hot air from the
engine over the carburetor area. NOTE: Refer to the
engine manufacturer's manual for service and maintenance of the engine.
v. 02/14
PROBLEM
POSSIBLE CAUSE
SOLUTION
LOW OPERATING
PRESSURE
Insufficient water supply. Closed
faucet. Inlet hose kinked
Use larger garden hose; clean inlet water
screen. Open faucet.
Clogged inlet hose strainer
Check plumbing system for leaks. Retape
leaks with teflon tape.
Faulty or mis-adjusted unloader
valve
Adjust unloader for proper pressure. Install
repair kit when needed. Call local distributor.
Worn packing in pump
Call Dealer Customer Support.
Machine has been stored in freezing temperatures
Thaw out machine completely, including
hose, spray gun and wand.
Slow engine RPM
Call local distributor.
Worn or dirty pump valves
Call local distributor.
Nozzle is obstructed
Blow out or remove debris with fine needle.
Pump sucking air, inlet hose
leaking
Check that all hoses and fittings are airtight.
Turn off machine and trigger spray gun until
a steady flow of water emerges through the
nozzle.
Insufficient water supply
Turn water on full force. Check garden hose
for kinks, leaks or blockage.
PRESSURE LOW
AFTER PERIOD OF
NORMAL USE
Nozzle worn
Replace nozzle.
Unloader valve worn
Replace unloader valve.
ENGINE WILL NOT
START OR STOPS
WHILE OPERATING
Low oil shutdown
Fill engine with oil.
Out of gas
Fill fuel tank.
Water in gasoline
Drain gas tank; fill with clean fuel.
ENGINE IS
OVERLOADED
Nozzle partially blocked
Clean nozzle.
Excessive pressure from high
engine RPM
Adjust engine throttle to lower RPM.
WATER OR OIL
LEAKING FROM
BOTTOM OF PUMP
A small amount of leaking is
normal
If excessive leaking occurs, Call local
distributor.
FLUCTUATING
PRESSURE
PRESSURE WASHER Troubleshooting Guide
OUBLESHOOTING
T-
13
!"#$%& '!# ( )* ( +,v. 02/14
PRESSURE WASHER Troubleshooting Guide
TROUBLESHOOTING
PROBLEM
POSSIBLE CAUSE
SOLUTION
ENGINE OPERATES
FOR 15 MINUTES
THEN STOPS
Not enough gas or engine oil
Fill tank with gas. Check oil level.
Vapor lock developed by heat of day
Keep gas tank full to avoid vapor locking.
Obstruction in fuel filter
Clean or replace fuel filter.
ENGINE LACKS
POWER
Dirty air filter
Replace air filter.
ENGINE FALTERS
Choke is opened too soon
Move choke to halfway position until engine
runs smoothly.
WATER DRIPPING
Piston packing worn
FROM UNDER PUMP O-Ring plunger retainer worn
Call local distributor.
Call local distributor.
Cracked piston
Call local distributor.
OIL DRIPPING
Oil seal worn or damaged
Call local distributor.
WATER LEAKING
FROM PUMP
PROTECTOR
Spray gun closed with machine
running 5 minutes or longer
Open spray gun or turn off machine.
Excess water supply pressure
Place a pressure regulator at end of 50'
garden hose.
NO DETERGENT
Detergent suction tube not properly
connected to machine
Check connection.
Detergent is too thick
Dilute detergent. For best results, use
manufacturers detergent.
Detergent filter valve is at lowest
setting
Set detergent filter valve to a higher setting.
Filter on detergent suction tube is
clogged
Run warm water through filter to remove
debris.
Damaged or clogged detergent suction tube
Remove obstruction or replace detergent
suction tube.
A high pressure nozzle is attached.
Replace with black detergent nozzle.
Discharge nozzle is obstructed
Blow out or remove debris with fine needle.
GARDEN HOSE
CONNECTION
LEAKS
Loose fittings
Tighten fittings.
Missing/worn rubber washer
Insert new washer.
SPRAY WAND
LEAKS
Spray wand not properly attached
Slide the spray wand into the gun. Turn the
wand collar clockwise onto the spray gun
threads until tight.
Broken o-ring
Call local distributor and order an o-ring.
Pump is sucking air
Check that hoses and fittings are air tight.
Turn off machine and purge pump by
squeezing trigger gun until a steady flow of
water emerges through nozzle.
PUMP IS NOISY
=>
./02345.6/2 7 8: 7 ;<v. 02/14
This pressure washer was produced with the best available materials and quality craftsmanship. However, you
as the owner have certain responsibilities for the correct care of the equipment. Attention to regular preventative maintenance procedures will assist in preserving the performance of your equipment. Contact your dealer
for maintenance. Regular preventative maintenance will add many hours to the life of your pressure washer.
Perform maintenance more often under severe conditions. Check pump oil and engine oil level before first use
of your new pressure washer.
MNOPQRPNPUR VUXRYZ[R
Engine Oil
Air Cleaner/Filter
Inspect
Daily
Change
First month or 20 hours.
Every 100 hours or every 6 months after first month
Filter
Every 50 hours
Inspect
Every 50 hours
Clean
Monthly
Engine Fuel Filter
500 hours or 6 months
Spark Plug Maintenance
300 hours or annually
Clean Fuel Tank(s)
Annually
Replace Fuel Lines
Annually
Replace High Pressure Nozzle
Every 6 months
Replace Quick Connects/O-Rings
Annually/As needed
Clean Water Screen/Filter
Weekly
Replace HP Hose
Annually (if there are any signs of wear)
PRESSURE WASHER Troubleshooting Guide
PREVENTATIVE MAINTENANCE
15
?@ABCEF?G@B H IJ H KLv. 02/14
PRESSURE WASHER
HOSE & SPRAY GUN ASSEMBLY
2
OPERATOR’S MANUAL
3
6
1
4
HOSE & SPRAY GUN ASSEMBLY PARTS LIST
ITEM
PART NO.
DESCRIPTION
QTY
1
9.162-323.0
HP HOSE DN8/50'/4000/NOLOGO/BLK/RBR
1
2
9.112-017.0
AL5 GUN 4000 PSI
1
3
9.112-527.0
LANCE-AL QUICK CONNECT -MALE 4000 PSI
1
4
9.104-016.0
9.104-030.0
8.751-357.0
QUICK CONNECT NOZZLE KIT (0325) (252437 & 262637 MODELS)
Q/C NOZZLE KIT (040) (403637 MODEL)
KIT, NOZZLE, QUICK DISCONNECT (045) (313137 MODEL)
1
1
1
ij
\]^_`ab\c]_ d ef d ghv. 02/14
Check engine oil level before first use of your new pressure washer.
xyz{ |}~ €y‚ed
Month/Day/Year
Estimated Operating
Hours Since Last
Oil Change
Date Oil Changed
Month/Day/Year
Estimated Operating
Hours Since Last
Oil Change
PRESSURE WASHER
OIL CHANGE RECORD
OPERATOR’S MANUAL
17
klmnopqkrln s tu s vwv. 02/14
ƒƒƒ.shark-pw.com
Form #9.801-597.0 • KG • Revised 02/14 • Printed in U.S.A. or Mexico