LCD Projector

WL7200U/WL7050U

Controlling the projector via RS-232C connection

Contents

1. Introduction ............................................................................................................ 2

1.1 Connection ............................................................................................................................... 2

1.2 Interface ................................................................................................................................... 2

1.2.1 Pin assignment of SERIAL terminal (D-SUB 9-pin) .............................................................................. 2

1.2.2 Communications format ...................................................................................................................... 2

2. Control command configuration ............................................................................ 3

3. Control sequence ................................................................................................... 3

4. Execution procedure of RS-232C commands via LAN .......................................... 6

5. Command list ......................................................................................................... 7

5.1 General control commands ...................................................................................................... 7

5.2 Reading commands ................................................................................................................. 7

5.2.1 Status read commands ........................................................................................................................ 7

5.2.2 Read commands for items in INFORMATION menu ............................................................................ 7

5.2.3 Read commands for other information ................................................................................................ 8

5.3 Remote control key commands ............................................................................................... 9

5.4 Direct commands ................................................................................................................... 10

5.5 Function commands .............................................................................................................. 10

5.6 Menu setting commands ....................................................................................................... 11

5.6.1 IMAGE menu ...................................................................................................................................... 11

5.6.2 INSTALLATION menu ......................................................................................................................... 11

5.6.3 FEATURE menu .................................................................................................................................. 12

5.6.4 SIGNAL menu .................................................................................................................................... 12

5.6.5 NETWORK menu ............................................................................................................................... 13

5.7 Password lock commands ..................................................................................................... 14

1

1. Introduction

This projector is controllable by a personal computer with RS-232C terminal.

PC-controllable functions:

• Turning the power ON or OFF

• Changing input signals

• Inputting commands by pressing the buttons on the control panel and remote control

• Menu setting

[Compatibility with the former models]

To use the RS-232C commands designed for the former models of Mitsubishi projector, by inputting

“00COMMAND0”, the projector responds in the same way as the former models. (No NAK is returned. For NAK response, see page 4.)

(For the recommended procedure to use the former command systems, see “Controlling the projector using a personal computer” for FL7000U.)

ITEM

Changing the RS-232C command system

Character

Function

ASCII code

Data

COMMAND 43h 4Fh 4Dh 4Dh 41h 4Eh 44h 0 (Former command system), 1 (New command system)

1.1 Connection

Important:

• Make sure to connect one computer to one projector.

• Make sure that your computer and projector are turned off before connection.

• Boot up the computer first, and then plug the power cord of the projector.

(If you do not follow this instruction, the COM port may not function.)

• Adapters may be necessary depending on the PC connected to this projector. Contact your dealer for details.

To RS-232C terminal

RS-232C crossover cable

To SERIAL terminal

D-SUB 9-pin D-SUB 9-pin

1.2 Interface

1.2.1 Pin assignment of SERIAL terminal (D-SUB 9-pin)

Pin No.

1

2

3

4

5

6

7

8

9

Name

OPEN

RXD

TXD

OPEN

GND

OPEN

OPEN

OPEN

OPEN

I/O

IN

OUT

1.2.2 Communications format

PROTOCOL

BAUD RATE

DATA LENGTH

PARITY BIT

STOP BIT

FLOW CONTROL

RS-232C

9600 [bps]

8 [bits]

NONE

1 [bit]

NONE

This projector uses RXD, TXD and GND lines for RS-232C control.

For RS-232C cable, the supplied cable (crossover cable) should be used.

2

2. Control command configuration

The command consists of the address code, function code, data code, ACK/NAK, and end code. The length of the command varies among the functions.

ASCII code

Character

Address code

‘30h’ ‘30h’

00

Function code

Function

Function

Data code

Data

Data

ACK/NAK

‘3Ah’ ‘4Eh’

:N

End code

‘0Dh’

[Address code] Fixed to 00. (‘30h’ ‘30h’ in the ASCII code)

[Function code] Code unique to each control operation.

[Data code]

[ACK/NAK]

Data (value) unique to each control operation (Not always indicated.)

Code indicating the NAK return as described below

[End code]

Fixed to :N (‘3Ah’ ‘4Eh’ in the ASCII code. Not added to ACK.)

Fixed to . (‘0Dh’ in the ASCII code)

3. Control sequence

Computer Projector

3

4

1

2

1

2

3

4

Sequence

Send the command from the personal computer to the projector.

After receiving the end code, the projector sends the return command.

Note

If the projector does not receive commands normally, that is, if the projector is not connected physically or unable to receive commands, it does not send out a return command.

When the received command cannot be executed,

NAK is returned (as described below).

The personal computer checks the return command and confirms if the sent command has been received or not.

Use the check command to see if the projector has executed the command.

This projector sends various codes including the return code. During the control sequence by RS-232C, reject other codes on the personal computer.

3

• NAK return

In the following cases, the projector returns the command with “:N” added.

(1) Though the command sent from the computer is received by the projector successfully, it cannot be executed because the projector is in the operation prohibition state.

(2) The data length of the sent command is incorrect or the command is invalid.

(3) The signal length of the command is 48 bytes or longer.

• When a command is sent out during the following operations, it may not be executed.

(1) During signal switching

(2) In the process of the auto position

(3) After the power is turned on.

After the power is turned on, no command is received until the image is displayed. (Usually, it takes about

20 seconds. However, when the lamp illumination takes time, more time will be required accordingly.) In this case, the projector returns the received command with NAK added.

• The return command is sent out within 1 second. In some cases, the response time takes longer (about 3 seconds).

• When sending commands successively, wait to receive the return command of the current command before sending a next command.

• The projector may not receive a command when the splash screen is being displayed immediately after turning on the power. Use command “00r10” to cancel the splash screen.

• While using the LAN terminals, the LAN functions take precedence.

• For the LAN terminals, the same commands as those for connecting with the TCP/IP (port number 63007) are available. Note, however, that the response becomes slightly slower than when using the RS-232C terminals.

For the use of LAN terminals, refer to “4. Execution procedure of RS-232C commands via LAN”.

• When the NAK isn’t returned, check the RS-232C command system (00COMMAND).

[Example 1] Turning ON the power. (Values enclosed in quotation marks are ASCII codes.):

Command sent from the PC

Status code returned from the projector

Description

‘30’ ‘30’ ‘21’ ‘0D’

00!

Command for POWER ON

‘30’ ‘30’ ‘21’ ‘0D’

00!

Command receipt confirmation

(Command echo back)

[Example 2] Selecting VIDEO as the input signal during auto positioning (Values enclosed in quotation marks are

ASCII codes.):

Command sent from the PC

Status code returned from the projector

Description

30’ ‘30’ ‘5F’ ‘76’ ‘31’ ‘0D’

00_v1

‘30’ ‘30’ ‘5F’ ‘76’ ‘31’ ‘3A’ ‘4E’ ‘0D’

00_v1:N

(During auto positioning)

Command for selecting VIDEO as the input signal is sent out.

The command is received by the projector but cannot be executed.

(NAK return)

• The flowchart on the next page shows the recommended operating sequence for your reference to create a program.

4

[RS-232C control flowchart]

No NAK returned

START

Sending out command

Awaiting response from projector

NAK returned

No response for

3 seconds or longer

Command is sent successfully.

Command execution fails.

Command sending fails.

Command is sent successfully.

Command is executed successfully.

Checking execution of command (sending out check command)

OK

END

NG

Check the following.

• Check that the function code is correct.

• Check that the data code is correct.

• Check that the projector is able to issue the return command.

→ Check the projector’s operation using the 00vST command.

Note: In the following cases, NAK is returned even when the projector is in normal condition.

• Immediately after the power is turned on

(For status read commands) approximately for 20 seconds

(For other commands) approximately for 1 minute

• During input switching

• During auto positioning

• During password lock

Check the following.

• Check that the command begins with “00”.

• The projector is not supplied with

AC power.

→ Check that AC power cord is connected.

→ Turn on the power. (Turn on the circuit breaker.)

• Not connected with the projector.

→ Check that the RS-232C cable is connected.

→ Check the RS-232C cable for electrical discontinuity.

[Method of checking state of projector]

Sending “00vST”

To normal operation

0–3

Enter password.

Send out “00PASS****.”

6

Checking response to “00vST”

4

Projector error

Send out “00vER” to check error details.

Recover from error state.

5

Projector is functioning.

Use “00FNCOFF” to cancel the current function.

5

4.

Execution procedure of RS-232C commands via LAN

• When you use the LAN function, set the STANDBY MODE to STANDARD or LAN.

• When you execute RS-232C commands via LAN, check that the CONTROL SYSTEM in the NETWORK menu is set to STANDARD.

• You can change the certification password using the NETWORK PASSWORD in the NETWORK menu. The default password is “admin.”

• You can skip the certification process by setting the NETWORK CERTIFICATION in the NETWORK menu to OFF.

When you skip the certification process, Steps 2 to 4 described below can be skipped and you can send RS-232C commands without adding a certification data.

Example:

Sending the PON command (00!) while the NETWORK CERTIFICATION is set to OFF

00!

For the procedure to set the menu, refer to the User Manual supplied with the projector.

To execute the RS-232C command via LAN while the NETWORK CERTIFICATION is set to ON, a 32-byte connection certification data must be added before the RS-232C command.

To create a 32-byte certification data, following information and procedure are required.

• Random character string for creating the certification data that is acquired from the projector (8 characters)

• Network password of the projector (1 to 32 characters)

• MD5 hash calculation

• Based on the above, the execution procedures to connect to the projector and send the RS-232C commands while the NETWORK CERTIFICATION is set to ON are described below.

1. Connect to Port 63007 of the projector from the PC as a TCP/IP client.

2. After completing the connection, send the acquisition request for the certification data (“ $AK ”) (ASCII code: 24 41 4B 0D) from the PC to the projector.

3. Acquire “ $AK******** ” on the PC as the response of the request sent in Step 2. (********: Random character string for creating the certification data)

4. Create the certification data on the PC.

• Create the key of the certification data by linking the data acquired in Step 3 with the network character string.

For example, when the random character string is 12345678 and the password is ABCD, the key of the certification data is 12345678ABCD (character string in ASCII code).

• Run MD5 hash on the key of the certification data.

• Create the certification data by converting the hash-calculated 16-byte data into the ASCII code character string.

Example:

Calculation result: [4f][3c][5d][a1][7b][4f][b5][ed][2c][99][4e][bb][f6][57][67][54] (hexadecimal numeral)

Certification data: 4f 3c 5d a1 7b 4f b5 ed 2c 99 4e bb f6 57 67 54 (character string in ASCII code)

5. Send the RS-232C command with the certification data from the PC to the projector.

Example:

To send the PON command (00! ) using the certification data created in Step 4:

4f3c5da17b4fb5ed2c994ebbf657675400!

6. Receive the response from the projector on the PC.

Response data has the following patterns.

Normal: 00!

(Parameter is added depending on the command.)

Error in the certification data: PRV=ERRA

Command error: 00!:N

PC Projector

1. Connection

2. Acquisition request of the certification data

3. Receiving of the certification data

4. Creation of the certification data

5. Sending of the RS-232C command

6. Receiving of the response data

6

5.

Command list

5.1 General control commands

The general control commands are used for the basic operation setting of this projector. They may not be executed while the signals are changed. The general control commands have no data codes. (When the commands for input select are sent while the splash screen is being displayed, the splash screen is only canceled.)

ITEM

Function

Character ASCII code

POWER ON !

POWER OFF "

INPUT COMPUTER 1 _r1

INPUT COMPUTER 2 _r2

INPUT HDMI _d1

21h

22h

This command is invalid for 150 seconds after the power is turned off.

This command is invalid for 1 minute after the power is turned on.

5Fh 72h 31h This command is not received during stand-by and BLANK.

5Fh 72h 32h

5Fh 64h 31h

Note

This command is not received during stand-by and BLANK.

This command is not received during stand-by and BLANK.

INPUT DVI

INPUT VIDEO

INPUT S-VIDEO

_d2

_v1

_v2

5Fh 64h 32h This command is not received during stand-by and BLANK.

5Fh 76h 31h This command is not received during stand-by and BLANK.

5Fh 76h 32h This command is not received during stand-by and BLANK.

[Example] When setting the input signal to COMPUTER 1. (Values enclosed in quotation marks are ASCII codes.):

Command sent from the PC, etc.

Status code returned from the projector

Description

‘30’ ‘30’ ‘5F’ ‘72’ ‘31’ ‘0D’

00_r1

‘30’ ‘30’ ‘5F’ ‘72’ ‘31’ ‘0D’

00_r1

Command for setting the input signal to COMPUTER 1

Command receipt confirmation

(Command echo back)

5.2 Reading commands

5.2.1 Status read commands

The projector’s operating status, such as POWER-ON/OFF and the currently selected input terminal, etc. can be monitored.

POWER

INPUT

ITEM

P-ON/OFF

ENABLED/DISABLED

SIGNAL INPUT

Character vP

Function

ASCII

76h 50h vI vPK vSM

76h 49h

76h 50h 4Bh

76h 53h 4Dh

Data (Receive)

Character

1

ASCII

31h

0 r1 r2 d1

30h

72h 31h

72h 32h

64h 31h d2 v1 v2

64h 32h

76h 31h

76h 32h

0

1

0

1

30h

31h

30h

31h

Status

POWER ON

POWER OFF

INPUT COMPUTER 1

INPUT COMPUTER 2

INPUT HDMI

INPUT DVI

INPUT VIDEO

INPUT S-VIDEO

POWER ON/OFF

DISABLED

POWER ON/OFF

ENABLED

NO SIGNAL SUPPLIED

SIGNAL SUPPLIED

5.2.2 Read commands for items in INFORMATION menu

Use the following commands to obtain the values of the items in the INFORMATION menu.

ITEM

LAMP TIME (LOW)

SERIAL NUMBER

RESOLUTION

Character vLE vS/N vRESO

VERTICAL FREQUENCY vVFREQ

HORIZONTAL FREQUENCY vHFREQ

SYNC. TYPE vSYNCT

Function

ASCII code

76h 4Ch 45h

76h 53h 2Fh 4Eh

76h 52h 45h 53h 4Fh

76h 56h 46h 52h 45h 51h

76h 48h 46h 52h 45h 51h

76h 53h 59h 4Eh 43h 54h

Data (Receive) hhhhmm

******* (within 7 characters)

HHHHxVVVV

***.**

***.**

0 (NO SIGNAL), 1 (Invalid), 3 (3wire),

4 (4wire), 5 (5wire), 6 (SCART)

“hhhh” and “mm” represent hours and minutes respectively.

“HHHH” and “VVVV” represent the horizontal and vertical resolutions respectively.

“***.**” represents the vertical frequency (in Hz) or the horizontal frequency (in kHz).

7

5.2.3 Read commands for other information

Use the following commands to obtain other information.

ITEM

Model name

Input source

Character vMDL

Function

ASCII code

76h 4Dh 44h 4Ch

Data (Receive)

**************** (within 16 characters) vSOUCE 76h 53h 4Fh 55h 43h 45h r1 r2 v1 v2 d1 d2

Number of remaining filters *1) vFLTS

Reading of filter usage time *1) vFLTT

Projector status vST

Error status vER

76h 46h 4Ch 54h 53h

76h 46h 4Ch 54h 54h

76h 53h 54h

76h 45h 52h

00 to 09

0000 to 9999

0 (Stand-by mode),

1 (Within 1 minute after POWER-ON (warm-up mode)),

2 (POWER-ON mode (including state of warning)),

3 (Cooling mode),

4 (Abnormal state (including shutdown due to an error)),

5 (State of functioning (menu display, dialog display,

BLANK, SPLIT, MAGNIFY, FREEZE, etc.)),

6 (Awaiting password entry)

Reading of the error status data (3 digits, hexadecimal numbers, total 9 bits)

(MSB) xb1, xb2... xb8, xb9, 0, 0, 0 (LSB) xb1(800): Fan error xb2(400): Lamp error (The lamp goes out or does not light.) xb3(200): Lamp warning 1 (The lamp life has expired.) xb4(100): Lamp warning 2 (The lamp life is expiring.) xb5(080): Temperature error xb6(040): The temperature warning is being indicated.

xb7(020): Lamp cover open error xb8(010): Filter/filter cover open error xb9(008): States of other component abnormality

When only one error occurs, value shown in parentheses is returned.

When multiple errors occur at the same time, the bits of all the occurred error are set.

Example)

C00: When fan error and lamp error occur at the same time

180: When lamp warning 2 and temperature error occur at the same time

*1) This function works only on WL7200U.

The PC sends the command without attaching the data code to it. On the other hand, the projector attaches to the received command its current operating status as the data code and send it back to the PC.

[Example] When checking the currently selected input terminal (when the INPUT VIDEO is being selected).

(Values enclosed in quotation marks are ASCII codes.):

Command sent from the PC, etc.

‘30’ ‘30’ ‘76’ ‘49’ ‘0D’

00vl

Status code returned from the projector

‘30’ ‘30’ ‘76’ ‘49’ ‘76’ ‘31’ ‘0D’

00vlv1

Description

Command for checking the input terminal

Check result (VIDEO)

8

5.3 Remote control key commands

(Not executable in stand-by mode. When the remote control key commands are sent while the splash screen is being displayed, the splash screen is only canceled.)

The remote control key commands allow the computer to control the projector in the same way as by the remote control.

(Some operations cannot be controlled.) The remote control key commands have no data codes.

Button’s name on remote control

+/VOLUME

-/VOLUME

ZOOM/FOCUS

LENS SHIFT

GEOMETRY

MAGNIFY

PinP/SPLIT (SPLIT only)

BLANK

MENU

ENTER

AUTO POSITION

FREEZE

ASPECT

CE

TEST PATTERN

SUPER RESOLUTION

1 (numeric keypad)

2 (numeric keypad)

3 (numeric keypad)

4 (numeric keypad)

5 (numeric keypad)

6 (numeric keypad)

7 (numeric keypad)

8 (numeric keypad)

9 (numeric keypad)

0 (numeric keypad) r50 r96 r49 r4a r09 ra4 re2 re7 r4b r4c r4d r4e r88 r58 r89 r48 r53 r2b r4f r59 r54 r10 r43 r02 r04 ra6

Character r06 r07 r0f r47

Function

ASCII code

72h 30h 36h

72h 30h 37h

72h 30h 66h

72h 34h 37h

72h 34h 33h

72h 30h 32h

72h 30h 34h

72h 61h 36h

72h 35h 33h

72h 32h 62h

72h 34h 66h

72h 35h 39h

72h 35h 34h

72h 31h 30h

72h 30h 39h

72h 61h 34h

72h 65h 32h

72h 65h 37h

72h 35h 30h

72h 39h 36h

72h 34h 39h

72h 34h 61h

72h 34h 62h

72h 34h 63h

72h 34h 64h

72h 34h 65h

72h 38h 38h

72h 35h 38h

72h 38h 39h

72h 34h 38h

[Example] When displaying the MENU selection bar. (Values enclosed in quotation marks are ASCII codes.):

Command sent from the PC, etc.

Status code returned from the projector

Description

‘30’ ‘30’ ‘72’ ‘35’ ‘34’ ‘0D’

00r54

‘30’ ‘30’ ‘72’ ‘35’ ‘34’ ‘0D’

00r54

Command operating the same as the

MENU button

Command receipt confirmation

(Command echo back)

9

5.4 Direct commands

(Not executable in stand-by mode. Possible only to read during BLANK.)

The direct commands are used to numerically adjust the geometrical correction and volume.

When the computer sends the command without adding the setting value, the projector returns the received command with the current setting value added as a data code.

ITEM

KEYSTONE (vertical)

KEYSTONE (horizontal)

Character

KS

KSH

Function

ASCII code

4Bh 53h

4Bh 53h 48H

Data

±40

With CURVED-adjustment : ±10

±25

With CURVED-adjustment : ±10

KEYSTONE reset

CORNERSTONE LOWER RIGHT

(vertical)

CORNERSTONE LOWER RIGHT

(horizontal)

CORNERSTONE LOWER LEFT

(vertical)

CORNERSTONE LOWER LEFT

(horizontal)

CORNERSTONE UPPER RIGHT

(vertical)

CORNERSTONE UPPER RIGHT

(horizontal)

CORNERSTONE UPPER LEFT

(vertical)

CORNERSTONE UPPER LEFT

(horizontal)

CORNERSTONE reset

HORIZ. CURVED ARC

KSRST

CNLRV

CNLRH

CNLLV

CNLLH

CNURV

4Bh 53h 52h 53h 54h

43h 4Eh 4Ch 52h 56h

43h 4Eh 4Ch 52h 48h

43h 4Eh 4Ch 4Ch 56h

43h 4Eh 4Ch 4Ch 48h

43h 4Eh 55h 52h 56h

CNURH 43h 4Eh 55h 52h 48h

CNULV

CNULH

43h 4Eh 55h 4Ch 56h

43h 4Eh 55h 4Ch 48h

±60

±60

±60

±60

±60

±60

±60

±60

VERT. CURVED ARC

CKSRST 43h 4Bh 53h 52h 53h 54h

CVAH 43h 56h 41h 48h

CVAV 43h 56h 41h 56h

±50

With KEYSTONE-adjustment

: ±15

±50

With KEYSTONE-adjustment

: ±15

±10

±10

HORIZ. CURVED ORIGIN (vertical)

HORIZ. CURVED ORIGIN

(horizontal)

VERT. CURVED ORIGIN (vertical)

CVHOV

CVHOH

CVVOV

VERT. CURVED ORIGIN (horizontal) CVVOH

43h 56h 48h 4Fh 56h

43h 56h 48h 4Fh 48h

43h 56h 56h 4Fh 56h

43h 56h 56h 4Fh 48h

CURVED reset

VOLUME

CVRST

VL

43h 56h 52h 53h 54h

56h 4Ch

±10

±10

00 to 31

How to set the value

Use the character or ASCII code as shown below to set the value.

Character + 0 1 2 3 4 5 6 7 8 9

ASCII code ‘2Bh’ ‘2Dh’ ‘30h’ ‘31h’ ‘32h’ ‘33h’ ‘34h’ ‘35h’ ‘36h’ ‘37h’ ‘38h’ ‘39h’

5.5 Function commands

(Not executable in stand-by mode. When these commands are sent while the splash screen is being displayed, the splash screen is canceled.)

ITEM

BLANK

SPLIT

MAGNIFY

FREEZE

Function canceling

Character

MUTE

SPLT

MGNFY

Function

ASCII code

4Dh 55h 54h 45h

53h 50h 4Ch 54h

4Dh 47h 4Eh 46h 59h

FRZ 46h 52h 5Ah

FNCOFF 46h 4Eh 43h 4Fh 46h 46h

Data

0 (OFF), 1 (ON)

0 (OFF), 1 (ON)

0 (OFF), 1 (ON)

0 (OFF), 1 (ON)

10

5.6 Menu setting commands

(Not executable in stand-by mode except some commands. Possible only to read during BLANK except some commands.)

The menu setting commands are used for the menu setting of this projector. If the personal computer sends the command without attaching the data code, the projector attaches to the received command its current setting value as the data code and send it back to the PC.

5.6.1 IMAGE menu

ITEM

COLOR ENHANCER

COLOR ENHANCER-

USER-GAMMA MODE

SUPER RESOLUTION

SUPER RESOLUTION-

LEVEL

CONTRAST

BRIGHTNESS

NCM (MODE)

NCM (R,G,B)

NCM (Y,C,M)

NCM (SATURATION)

NCM (RGB-TINT)

COLOR TEMP.

COLOR TEMP.-USER-

CONTRAST

COLOR TEMP.-USER-

BRIGHTNESS

COLOR

TINT

SHARPNESS

AUTO IRIS

NOISE REDUCTION

CTI

INPUT LEVEL

T

S

R

IRIS

NR

CTI

IPL

Character

CE

CEU1GS

DHD

DHDLV

Function

ASCII code

Data

43h 45h 0 (AUTO), 1 (PRESENTATION), 2 (STANDARD),

3 (THEATER), 4 (sRGB), 5 (USER),

6 (CLEAR BASE), 7 (BLUE BASE)

43h 45h 55h 31h 47h 53h 0 (DYNAMIC), 1 (NATURAL), 2 (DETAIL)

44h 48h 44h

44h 48h 44h 4Ch 56h

0 (OFF), 1 (ON)

1 to 5

PP

QQ

CMT

MRGB

MYCM

MSAT

MT

A

P

Q

CC

50h 50h

51h 51h

43h 4Dh 54h

4Dh 52h 47h 42h

4Dh 59h 43h 4Dh

4Dh 53h 41h 54h

4Dh 54h

41h

50h

51h

54h

53h

52h

49h 52h 49h 53h

4Eh 52h

43h 54h 49h

49h 50h 4Ch

43h 43h

±30

±30

1 (VIDEO), 2 (COMPUTER), 3 (USER), 4 (OFF)

±30 ±30 ±30 (R+G+B)

±30 ±30 ±30 (Y+C+M)

±05

±15

1 (STANDARD), 2 (HIGH), 3 (LOW), 4 (USER)

±30 ±30 ±30 (R, G, B)

±30 ±30 ±30 (R, G, B)

±10

±10

±05

0 (OFF), 1 (ON)

0 (OFF), 1 (ON)

0 (OFF), 1 (ON)

±5,

For DVI input: +0 (NORMAL), +1 (ENHANCED)

For HDMI input: +0 (AUTO), +1 (NORMAL),

+2 (ENHANCED)

0 (OFF), 1 (CC1), 2 (CC2) CLOSED CAPTION

5.6.2 INSTALLATION menu

ITEM

LAMP MODE

STANDBY MODE

AUTO POWER ON

AUTO POWER OFF

SPLASH SCREEN

BACK COLOR

IMAGE REVERSE

ZOOM/FOCUS LOCK

LENS SHIFT LOCK

LENS SHIFT RESET

DVI LONG CABLE

(MODE)

DVI LONG CABLE

(LEVEL)

Character

LM

STBY

APON

APOF

SS

BB

IR

FZL

LSL

LSRST

DVIC

Function

ASCII code

4Ch 4Dh

53h 54h 42h 59h

41h 50h 4Fh 4Eh

41h 50h 4Fh 46h

53h 53h

42h 42h

49h 52h

46h 5Ah 4Ch

4Ch 53h 4Ch

4Ch 53h 52h 53h 54h

44h 56h 49h 43h

DVICLV 44h 56h 49h 43h 4Ch 56h

Data

0 (STANDARD), 1 (LOW)

0 (STANDARD), 1 (LOW), 2 (LAN)

0 (OFF), 1 (ON)

0 (OFF), 1 (5 min.), 2 (10 min.), 3 (15 min.),

4 (30 min.), 5 (60 min.), 6 (4 hours), 7 (8 hours)

0 (OFF), 1 (ON)

0 (BLACK), 1 (BLUE), 2 (IMAGE)

0 (OFF), 1 (MIRROR), 2 (INVERT),

3 (MIRROR INVERT)

0 (OFF), 1 (ON)

0 (OFF), 1 (ON)

0 (AUTO), 1 (MANUAL)

00 to 21

11

5.6.3 FEATURE menu

ASPECT

ITEM

Character

SC

ASPECT-16:9-MODE SCM

PROJECTOR ID PID

PASSWORD FUNCTION PSLOCK

MENU POSITION

CINEMA MODE

FILTER MENU

-AUTO ROLL UP

PERIOD *1)

FILTER MENU

-MANUAL ROLL UP *1)

FILTER MENU

-REMAINING FILTERS *1)

FILTER MENU

-FILTER USAGE TIME *1)

FILTER MENU

-FILTER RESET *1)

LANGUAGE

MP

CINE

FLCP

FLMC vFLTS vFLTT

Function

ASCII code

53h 43h

53h 43h 4Dh

50h 49h 44h

50h 53h 4Ch 4Fh 43h

4Bh

4Dh 50h

43h 49h 4Eh 45h

46h 4Ch 43h 50h

46h 4Ch 4Dh 43h

46h 4Ch 54h 53h

46h 4Ch 54h 54h

Data

0 (NORMAL (FULL)), 1 (NORMAL(16:9)),

2 (NORMAL(4:3)), 3 (16:9), 4 (REAL), 5 (FULL)

0 (ALL SIGNALS), 1 (VIDEO ONLY)

00 (ALL), 01 to 63

0**** (UNLOCK), 1**** (DISPLAY INPUT),

2**** (MENU ACCESS), 3**** (SPLASH ID

SCREEN)

**** is a 4 to 8-digit password comprised of any figures 1 to 4.

0 (Upper left), 1 (Lower right)

0 (VIDEO), 1 (AUTO), 2 (FILM)

0 (OFF), 1 (Every 500 hours), 2 (Every 750 hours),

3 (Every 1000 hours)

00 to 09 (number of times)

0000 to 9999 (hours)

HIGH ALTITUDE MODE

VIDEO SIGNAL

(VIDEO only)

SET UP

SCART INPUT

LAMP WARNING

HIDE OSD

RESET ALL

TRSTFL 54h 52h 53h 54h 46h 4Ch Reset of the number of remaining filters and filter usage time

LG 4Ch 47h 00 ( ), 01 (English), 02 (Español),

03 (Deutsch), 04 (Français), 05 (Italiano), 06 (

07 ( ), 08 ( ), 09 (PORTUGUÊS),

11 (SVENSKA), 12 (POLSKI), 16 (Nederlands),

),

17 (Norsk), 18 ( ), 19 (Türkçe),

20 ( ภาษาไทย ), 21 (Bahasa Indonesia), 22 (Melayu),

23 ( )

ALTI

VS

STU

SRT

LW

HOSD

RSTALL

41h 4Ch 54h 49h

56h 53h

53h 54h 55h

53h 52h 54h

4Ch 57h

48h 4Fh 53h 44h

52h 53h 54h 41h 4Ch 4Ch

0 (STANDARD), 1 (HIGH ALTITUDE)

0 (AUTO), 1 (NTSC), 2 (PAL), 3 (SECAM),

4 (4.43NTSC), 5 (PAL-M), 6 (PAL-N), 7 (PAL-60)

0 (AUTO), 1 (OFF), 2 (3.75%), 3 (7.5%)

0 (OFF), 1 (ON)

0 (STANDARD), 1 (SHORT TERM)

0 (OFF), 1 (ON)

*1) This function works only on WL7200U.

5.6.4 SIGNAL menu

ITEM

MEMORY CALL

HORIZ.POSITION

VERT. POSITION

FINE SYNC.

TRACKING

COMPUTER INPUT

OVER SCAN

HOLD

HOLD BEGIN

HOLD END

CLAMP POSITION

CLAMP WIDTH

VERT. SYNC.

LPF

SHUTTER(U)

SHUTTER(L)

SHUTTER(LS)

SHUTTER(RS)

VOS

HLD

HLB

HLE

CLP

CLW

VSC

LPF

Character

MMC

HP

VP

FN

TRK

CIN

SHU

SHL

SHLS

SHRS

Function

ASCII code

4Dh 4Dh 43h

48h 50h

56h 50h

46h 4Eh

54h 52h 4Bh

43h 49h 4Eh

56h 4Fh 53h

48h 4Ch 44h

48h 4Ch 42h

48h 4Ch 45h

43h 4Ch 50h

43h 4Ch 57h

56h 53h 43h

4Ch 50h 46h

53h 48h 55h

53h 48h 4Ch

53h 48h 4Ch 53h

53h 48h 52h 53h

*1) Setting range differs depending on the input signals.

Data

0 (AUTO), 1 (MEMORY1), 2 (MEMORY2)

+ (increment), - (decrement) *1

+ (increment), - (decrement) *1

00 to 31

+ (increment), - (decrement) *1

0 (RGB), 1 (YC

B

C

R

/YP

B

P

R

), 2 (AUTO)

00 (90%) to 10 (100%)

0 (OFF), 1 (ON)

00–99

00–99

001–255

01–63

0 (AUTO), 1 (OFF)

0 (OFF), 1 (ON)

00 to 38

00 to 38

00 to 63

00 to 63

12

5.6.5 NETWORK menu

ITEM

PROJECTOR NAME

NETWORK RESTART

Character

NAME

NRCN

Function

ASCII code

4Eh 41h 4Dh 45h

4Eh 52h 43h 4Eh

Data

Up to 15 single-byte alphanumeric characters

• Some commands are not executed depending on the input signal. The operational restrictions same as those on the menu setting are applied. Refer to “Menu operation” in the User Manual for more details.

How to set the value

Use the character or ASCII code as shown below to set the value.

Character + 0 1 2 3 4 5 6 7 8 9

ASCII code ‘2Bh’ ‘2Dh’ ‘30h’ ‘31h’ ‘32h’ ‘33h’ ‘34h’ ‘35h’ ‘36h’ ‘37h’ ‘38h’ ‘39h’

[Example 1] When setting the AUTO POWER ON to ON. (Values enclosed in quotation marks are ASCII codes.):

Command sent from the PC, etc.

Status code returned from the projector

Description

‘30’ ‘30’ ‘41’ ‘50’ ‘4F’ ‘4E’ ‘31’ ‘0D’

00APON1

‘30’ ‘30’ ‘41’ ‘50’ ‘4F’ ‘4E’ ‘31’ ‘0D’

00APON1

Command for setting the AUTO

POWER ON to ON

Command receipt confirmation

(Command echo back)

[Example 2] When setting the CONTRAST R of the COLOR TEMP.-USER to +10, the CONTRAST G to 0, and the

CONTRAST B to -5. (Values enclosed in quotation marks are ASCII codes.):

Command sent from the PC, etc.

‘30’ ‘30’ ‘50’ ‘2B’ ‘31’ ‘30’ ‘2B’ ‘30’ ‘30’ ‘2D’ ‘30’ ‘35’ ‘0D’

00P+10+00-05

Status code returned from the projector

‘30’ ‘30’ ‘50’ ‘2B’ ‘31’ ‘30’ ‘2B’ ‘30’ ‘30’ ‘2D’ ‘30’ ‘35’ ‘0D’

00P+10+00-05

Description

Command for setting the picture control

Command receipt confirmation

(Command echo back)

[Example 3] When checking the TINT setting (when the TINT is set to +10). (Values enclosed in quotation marks are ASCII codes.):

Command sent from the PC, etc.

Status code returned from the projector

Description

‘30’ ‘30’ ‘53’ ‘0D’

00S

‘30’ ‘30’ ‘53’ ‘2B’ ‘31’ ‘30’ ‘0D’

00S+10

Command for checking the

TINT setting

Check result (+10)

[Example 4] When setting the GAMMA MODE of the COLOR ENHANCER-USER to DETAIL. (Values enclosed in quotation marks are ASCII codes.):

Command sent from the PC, etc.

Status code returned from the projector

Description

‘30’ ‘30’ ‘43’ ‘45’ ‘55’ ‘31’ ‘47’ ‘53’ ‘32’ ‘0D’

00CEU1GS2

‘30’ ‘30’ ‘43’ ‘45’ ‘55’ ‘31’ ‘47’ ‘53’ ‘32’ ‘0D’

00CEU1GS2

Command for setting the picture control

Command receipt confirmation

(Command echo back)

13

5.7 Password lock commands

The password lock commands control the password lock. The password lock enabling or disabling command is sent with a 4 to 8-digit password comprised of any figures 1 to 4 added to the end of the data code. When the password lock is enabled or disabled successfully, the projector sends a return command comprising the data code, password, and “1” at the end. When enabling or disabling the password lock fails, it sends a return command with “0” at the end. There is no reconfirmation of the password. The password input command is for enabling projection of image when password lock has been set to DISPLAY INPUT. The password input command is sent with a 4 to 8-digit password comprised of any figures 1 to 4 at the end.

ITEM

Password lock enabling/ disabling

Password input

Character

Function

ASCII code

Data

PSLOCK 50h 53h 4Ch 4Fh 43h 4Bh 0**** (Disabling), 1**** (DISPLAY INPUT),

2**** (MENU ACCESS), 3**** (SPLASH ID SCREEN)

PASS 50h 41h 53h 53h ****

**** is a 4 to 8-digit password comprised of any figures 1 to 4.

[Example] When enabling the password lock of DISPLAY INPUT (in the case that the password is 123412).

(Values enclosed in quotation marks are ASCII codes.):

Command sent from the PC, etc.

Status code returned from the projector

Description

‘30’ ‘30’ ‘50’ ‘53’ ‘4C’ ‘4F’ ‘43’ ‘4B’ ‘31’ ‘31’ ‘32’ ‘33’ ‘34’ ‘31’ ‘32’ ‘0D’

00PSLOCK1123412

‘30’ ‘30’ ‘50’ ‘53’ ‘4C’ ‘4F’ ‘43’ ‘4B’ ‘31’ ‘31’ ‘32’ ‘33’ ‘34’ ‘31’ ‘32’ ‘31’ ‘0D’

00PSLOCK11234121

Command for enabling the password lock of DISPLAY INPUT

Response informing that the projector succeeded in enabling the password lock of DISPLAY INPUT

14