Mitsubishi WD-52327 Service manual

MITSUBISHI ELECTRIC

Ser vice

Manual

DIGITAL LIGHT PROCESSING™ PROJECTION TV

VK26 CHASSIS

WD-52327

MODELS

WD-52327

WD-62327

CAUTION:

Before servicing this chassis, it is important that the service person read the "SAFETY PRECAUTIONS" and

"PRODUCT SAFETY NOTICE" contained in this manual.

SPECIFICATIONS

• Power Input

• Power Usage

• Light Engine

• Light Source

• Frequency Range

• Antenna Input

• Cabinet Dimensions

: AC 120V, 60Hz

: 200W

: DLP (1280 x 720p pixels)

: 120W VIP

: VHF 54 ~ 470MHz

UHF 470 ~ 806MHz

: VHF/UHF 75 Ω unbalanced

2 - NTSC

WD-52327

: 37.2"(H) x 49.6"(w) x 17.4"(D)

WD-62327

: 43.7"(H) x 58.3"(W) x 19.9"(D)

• Input Level : VIDEO IN JACK (RCA Type)

1.0Vp-p 75 Ω unbalanced

: AUDIO IN JACK (RCA Type)

-4.7dBm 43k Ω unbalanced

: S-VIDEO IN JACK

(Y/C separate type)

Y:1.0 Vp-p C:0.286Vp-p(BURST)

75 Ω unbalanced

: COMP / Y, Cr, Cb (RCA Type)

Y: 1.0 Vp-p Cr, Cb: 700mVp-p

: DTV / Y(G), Pr(R), Pb(B), H, V

Y: 1.0Vp-p with sync 75 Ω (BNC)

Pr, Pb: 700mV 75 Ω

H, V: 3.0Vp-p 75 Ω

• Weight [WD-52327] 110 lbs

[WD-62327] 139 lbs

• Speakers (8 Ohms 10W)

: 2-5 inch Coaxial

• Output Level

: VIDEO OUT JACK (RCA Type)

1.0Vp-p 75 Ω unbalanced

: AUDIO OUT JACK (RCA Type)

-4.7dBm 4.7k

Ω unbalanced

• Digital

: MonitorLink TM /DVI

• Design specifications are subject to change without notice.

9351 Jeronimo Road, Irvine, CA 92618-1904

Copyright © 2004 Mitsubishi Digital Electronics America, Inc.

All Rights Reserved

MODEL: WD-52327 / WD-62327

CONTENTS

INTRODUCTION ............................................................................................................................... 5

PRODUCT SAFETY NOTICE ........................................................................................................... 5

SAFETY PRECAUTIONS ................................................................................................................. 6

DISASSEMBLY

WD-52327 & WD-62327

Front Cabinet Components .................................................................................................... 7

Rear Cabinet Components ..................................................................................................... 8

CHASSIS REMOVAL

Chassis removal procedure .................................................................................................... 9

Shield Removal .................................................................................................................... 10

Chassis PWB locations ....................................................................................................... 11

Accessing the Lamp Ballast ................................................................................................ 12

OPTICAL ENGINE REPLACEMENT

Optical Engine Mounting ...................................................................................................... 13

Removing the Optical Engine ............................................................................................... 14

Removing DMD Heat Sensor ................................................................................................ 15

Removing Bottom Plate & Black Support Bracket. ............................................................... 15

Installing the Optical Engine ................................................................................................ 16

SERVICING THE LENTICULAR SCREEN AND FRESNEL LENS

Removal of the Lenticular Screen and Fresnel Lens ............................................................. 17

Installation of the Lenticular Screen and Fresnel Lens .......................................................... 19

ELECTRICAL ADJUSTMENTS

Equipment .................................................................................................................................... 20

Initial Setup (Option Menu) ............................................................................................................ 21

Main Menu Defaults ...................................................................................................................... 21

A/V Memory Defaults .................................................................................................................... 22

LED Indications ............................................................................................................................ 22

LED Dignostic Check .................................................................................................................... 23

Circuit Adjustment Mode ............................................................................................................... 23

Adjustment Items List ................................................................................................................... 25

Activating Internal Test Patterns .................................................................................................... 26

Adjustment Procedures ................................................................................................................ 27

Main & Sub Y level adjustments .......................................................................................... 27

Main & Sub Color level adjustments ..................................................................................... 27

White Balance Adjustments ................................................................................................. 28

Horizontal & Vertical Position adjustments .......................................................................... 28

Mechanical Adjustments ............................................................................................................... 29

Required Front Disassembly ................................................................................................ 29

Required Rear Disassembly ................................................................................................. 29

Picture Rotation Adjustment ............................................................................................... 30

Horizontal & Vertical Keystone Distortion adjustments ......................................................... 31

QUICK REFERENCE PART LIST ..................................................................................................... 32

Service Parts List ........................................................................................................................... 33

Screen Parts List ............................................................................................................................ 41

CIRCUITRY BLOCK DIAGRAMS

Standby power Supplies ....................................................................................................... 42

Switched Supplies ............................................................................................................... 42

Page 3

MODEL: WD-52327 / WD-62327

Switched DC to DC Supplies ............................................................................................... 43

Video/Color Signal Path ....................................................................................................... 44

Sound Signal Path ............................................................................................................... 45

Sync Signal Path ................................................................................................................. 46

Control Circuit (Commands, Serial Data & Reset) ................................................................ 47

Control Circuit (Status Inputs, OSD Insert & CCD Insert) ...................................................... 48

PWB-FORMAT Block Diagram ............................................................................................ 49

SCHEMATIC DIAGRAMS

BLOCK (PWB INTERCONNECTIONS) ......................................................................................... S1

1

Page 4

MODEL: WD-52327 / WD-62327

INTRODUCTION

This service manual provides service instructions for PTV models WD-52327 and WD-62327, using the VK26 chassis.

This service manual includes:

1. Assembly and disassembly instructions for the front and rear cabinet components.

2. Servicing of the Lenticular Screen and Fresnel Lens.

3. Servicing to PWB level. The Optical Engine and Lamp Ballast are considered replaceable components .

4. Electrical and Mechanical adjustments.

5. Chip parts replacement procedures.

6. Simplified signal path block diagrams.

The parts list section of this service manual includes:

1. Cabinet and screen parts.

2. Electrical parts.

Block diagrams of the above listed models are included in this service manual for better understanding of the circuitry.

PRODUCT SAFETY NOTICE

Many electrical and mechanical parts in television receivers have special safety related characteristics. These characteristics are often not evident from visual inspection nor can the protection afforded by them necessarily be obtained by using replacement components rated for higher voltage, wattage, etc.

Replacement parts which have special safety characteristics are identified in this service manual.

Electrical components having such features are identified by shading on the schematic diagram and by bold type in the parts list of this service manual. Therefore, the replacement for any safety part should be identical in value and characteristics.

Page 5

MODEL: WD-52327 / WD-62327

NOTICE:

SAFETY PRECAUTIONS

Observe all cautions and safety related notes located inside the receiver cabinet and on the receiver chassis.

WARNING:

1.

2.

Operation of this receiver outside the cabinet or with the cover removed presents a shock hazard from the receiver's power supplies. Work on the receiver should not be attempted by anyone who is not thoroughly familiar with the precautions necessary when working on high voltage equipment.

When service is required, observe the original lead dress. Extra precaution should be taken to assure correct lead dress in the high voltage area. Where a short-circuit has occurred, replace those components that indicate evidence of overheating.

WARNING ... RISK OF EYE INJURY

Do not look into the light source, Light Engine lens or mirror when operating the TV

Leakage current check

Before returning the receiver to the customer, it is recommended that leakage current be measured according to the following methods.

1. Cold Check

With the alternating current (AC) plug removed from the AC source, place a jumper across the two AC plug prongs. Connect one lead of an ohm meter to the AC plug and touch the other lead to each exposed metal part

(i.e. antennas, handle bracket, metal cabinet, screw heads, metal overlay, control shafts, etc.), particularly any exposed metal part that has a return path to the chassis. The resistance of the exposed metal parts having a return path to the chassis should be a minimum of 1Mega Ohm. Any resistance below this value indicates an abnormal condition and requires corrective action.

2. Hot Check ...Use the circuit shown below to perform the hot check test.

1. Keep switch S1 open and connect the receiver to the measuring circuit. Immediately after

connection, and with the switching devices of the receiver in their operating positions, measure the

leakage current for both positions of switch S2.

2. Close switch S1, energizing the receiver. Immediately after closing switch S1, and with the

switching devices of the receiver in their operating positions, measure the leakage current for both

positions of switch S2. Repeat the current measurements of items 1 and 2 after the receiver has

reached thermal stabilization. The leakage current must not exceed 0.5 milliampere (mA).

Page 6

MODEL: WD-52327 / WD-62327

CABINET DISASSEMBLY (FRONT VIEW)

WD-52327 / WD-62327

*Refer to the Parts List for Part Numbers

Front Cabinet Disassembly

1. Remove the SPEAKER-GRILLE by pulling forward.

2. Remove screws (a) to remove the COVER-FRONT.

3. Remove screws (b) on the rear of the upper back cover (4 across the top and 3 on each side).

4. Remove the 4 screws (c) holding the bottom of the Screen Assembly.

5. Unplug connector LN from the Control Panel.

6. Lift the Screen Assembly up slightly then pull towards the front to remove the assembly.

Page 7

REAR DISASSEMBLY

MODEL: WD-52327 / WD-62327

FILTER-COVER Removal

Remove 2 screws (d) to remove the Filter Cover.

COVER-BACK Removal

1) Remove 9 screws (a)

2) Remove 6 screws (b)

3) Remove 2 screws (c)

4) Pull the COVER-BACK from the cabinet.

NOTE: To operate the TV with the COVER-BACK removed, the FILTER-COVER must be reinstalled.

Rear Plate Removal

1) Remove 6 screws (a)

2 Remove 6 screws (b)

3) Pull the COVER-BACK from the cabinet.

4) Lay the Rear Plate down behind the TV.

Page 8

MODEL: WD-52327 / WD-62327

CHASSIS REMOVAL

Chassis Removal Procedure

1) Disconnect all relay connectors shown below (JE, CC, JJ, PP, LL & EE)

2) Disconnect the J9 and DVI connectors at the Optical Engine.

2) Remove three screws (a) securing the chassis.

3) Carefully slide the chassis from the cabinet.

Page 9

MODEL: WD-52327 / WD-62327

Shield Removal

1) To remove SHIELD-COVER, remove 11 screws (a).

2) To remove PWB-TERMINAL COVER, remove 9 screws (b).

Page 10

MODEL: WD-52327 / WD-62327

VK26 Chassis PWB Locations (Shield-Cover removed)

Page 11

MODEL: WD-52327 / WD-62327

Accessing The Lamp Ballast

Removing the Right Support (Rear View)

1) Remove the Air Filter.

2) Remove the 3 screws (a).

3) Lift the upper cabinet slightly to remove the support bracket.

Lift upper cabinet slightly to remove support.

(a)

Removing the Lamp Ballast Shield

(4 screws)

4 Screws

Remove

Air Filter

Unplug CJ3 & CN2

Connectors

Unplug

Connectors

Page 12

MODEL: WD-52327 / WD-62327

OPTICAL ENGINE REPLACEMENT

Optical Engine is mounted on the Adjuster assembly as shown below.

1) The Optical Engine is secured to the bottom plate with 4 screws (b).

2) The Black Bracket is secured to the bottom plate and the Lamp Cartridge Housing with 4 screws (c).

3) Tab (1) on the bottom plate slides into slot (1) on the Adjuster assembly.

4) 4 screws (a) secure the bottom plate and Optical Engine to the Adjuster assembly.

5) The Optical Engine, the bottom plate, black bracket and the Optical Engine are removed as a unit.

Page 13

MODEL: WD-52327 / WD-62327

Removing the Optical Engine

1) Remove the Cabinet BACK-BOARD and REAR-PLATE (refer to disassembly instructions).

2) Disconnect all connectors connected to the Engine and the PWB-FORMAT.

3) From the rear of the TV, remove the 4 screws (c), to remove the COVER-DUCT and DMD Fan cover.

4) From the rear of the TV, remove the 4 screws (a), shown below, securing the bottom plate to the Adjuster assembly.

5) Slide the Optical Engine, PWB-DMD and bottom plate towards the rear to remove the unit from the TV.

(a)

Optical Engine (Rear View / Airduct & DMD Fan Cover Removed)

Page 14

MODEL: WD-52327 / WD-62327

Remove the follolwing parts from the Optical Engine

• DMD Thermal Sensor

• The Optical Engine bottom plate and black bracket

DMD Termal Sensor Removal (Figure 1)

1) Remove screw (a) on the top of the DMD Fan.

2) Set the Thermal Sensor aside to install on the replacement Optical Engine.

(a)

Figure 1: DMD Thermal Sensor

Bottom Plate & Black Bracket Removal

1) Remove the 4 screws (B) from the Bottom Plate (Figure 2)

2) Remove the two screws (c), holding the Black Bracket to the Lamp Cartridge Housing. (Figure 3)

Bottom Plate

(B)

Bottom View

Figure 2: Bottom Plate

Page 15

MODEL: WD-52327 / WD-62327

(C)

Black Bracket

Front View

Figure 3: Black Support Bracket

Installing the Optical Engine

1) Install the Bottom Plate, Black Support Bracket and the Thermal Sensor from the original Optical Engine, on the replacement Engine

2) Reverse the removal procedure to install the replacement Optical Engine in the cabinet.

2) The following adjustments may have to be performed after the installation.

• Horizontal and Vertical Electrical Centering Adjustment.

• Optical Unit Rotation Adjustment

• Optical Unit Keystone Distortion Adjustments.

Page 16

MODEL: WD-52327 / WD-62327


CAUTION: Wear gloves when handling the Lenticular Screen and Fresnel Lens.

This prevents cuts and finger prints. Do not place Fresnel Lens in the sun.

This may cause fire and heat related injuries.

Lenticular Screen and Fresnel Lens Removal

1. Remove the screen assembly shown in the Cabinet Disassembly procedure.

2. Remove the four screws (a) to remove the bottom of the SCREEN-FRAME-BOTTOM . (Figure 1)

3. From the front of the screen assembly, slide the BEZEL out the bottom of the Screen Frame. (Figure 2)

4. From the rear of the screen assembly, carefully slide the Lenticular Screen and Fresnel Lens combination from the Screen Frame. (Figure 3)

Note: When separating the Lenticular Screen from the Fresnel Lens, use caution while prying the Screen and Lens apart. Use a slot type screw driver, and remove the pressure sensitive double sided tape.

Figure 1: SCREEN-FRAME-BOTTOM Removal (Rear View)

Page 17

MODEL: WD-52327 / WD-62327

Figure 2: BEZEL Removal (Front View)

Figure 3: Lenticular Screen & Fresnel Lens Removal (Rear View)

Page 18

MODEL: WD-52327 / WD-62327


Lenticular Screen and Fresnel Lens Installation

Note: Store the Lenticular Screen and Fresnel Lens in a cool dry place. High humidity may deform the Lenticular Screen and Fresnel Lens.

1. Apply double coated tape (Part #LENS-TAPE) along the top rear edge of the Lenticular Screen, as shown below. Refer to the table below for the tape length.

2. Sandwich the Fresnal Lens and Lenticular Screen together. The Lenticular Screen label must be towards the front and the Fresnel Lens label towards the rear. (Figure 4)

3. Apply pressure at the top edge to bond the screens together.

4. Reverse the Screen Removal procedure and insert the screens in the Screen Fame Assembly.

Figure 4: Installing the Fresnel Lens & Lenticular Screen

*X INCHES - Refer to the Tape Length in the table below

MODEL

WD-52327

WD-62327

SCREEN SIZE

52 Inches

62 Inches

TAPE LENGTH

46.3 Inches

55.1 Inches

Page 19

MODEL: WD-52327 / WD-62327

ELECTRICAL ADJUSTMENTS

Note: Perform only the adjustments required.

Do not attempt an alignment if proper equipment is not available.

Test Equipment

• Oscilloscope (Unless otherwise specified, use 10:1 probes)

• Signal Generator (NTSC Color Bar)

Test Signals

A. Internally Generated Square Pattern Signals

B. Color Bar Signal

Use the color bar signal shown below, unless otherwise specified in this manual.

100%

75%

40%

40%

1H

Split-Field Color Bars (100% window)

Page 20

MODEL: WD-52327 / WD-62327

Initial Setup

A. Option Menu Setup

Follow the steps below for the initial set-up:

1. Select the "MENU" display by pressing the "MENU" button once.

2. Press the number buttons "5", "7", "7", "0" in sequence to select the "OPTION MENU" display.

3. Press the "ADJUST" button to select "INITIALIZE."

4. Press "ENTER."

NOTE: At this time channel 3 is automatically selected.

OPTION MENU <MENU> <5-7-7-0>

Initialize

Power Restore:

DTV Port:

Direct Key Mode:

Off

AUTO

Off

Lamp Hours: TOTAL CURRNT PREV1

0 0 0

PREV2

0

Total TV

On Time

Current

Lamp

Time

Previous

Lamp

Time

Previous

Lamp

Time 2

B.

Default Settings

Se tup Me nu

Memorize Channels

Language

Energy Mode Standard V-Chip

Input Assignme nt Menu TV Rating

Antenna-A

Antenna-B

DTV

Component-1

On D-Sexual Dialog

YPrPb L-Adult Language

Comp-2 V-Violence Component-2

Input-1

Input-2

Input-3

MonitorLink™

Input-2

MonoLink

Programs Not Rated

V-Chip Start Time

Clock Me nu

Clock Setting

Clock Time

Set Day

Time Zone

Daylight Savings

Antenna

Channel

Memory

Name

Captions

Closed Captions

CC Background

Channel Edit Menu

VK26 M ain M enu Default Settings

Unlock Time

Ant-A Front Button Lock

N/A Red

Off Yellow

Off Cyan

TV-PG Blue

50%

50%

Allow Audio/Video Settings Menu

Allow A/V Memory Reset Ant-A

Allow TV Speakers (internal)

Allow

PG Bass

Allow Treble

12:00am

Audio Settings (TV)

Surrond

50%

50%

50%

On

Fixed

50%

50%

Center

Off

Manual

V-Chip Start Time 12:00am Listen To

Advanced Features Menu Level Sound

../..

Color Balance

Sunday Timer

TV Volume

Video Settings (TV)

N/A Video Mute

N/A Black Enhancementt

Color Balance Menu

In Mute

Gray PerfectColor™

Ant-A

Ant-A Auto Color Correction

Reset Color for Ant-A

003 Timer

Timer Menu

Deleted Set Time

N/A Set Day

On

On

Contrast

Brightness

Sharpness

Off Color

Tint

Color Temp.

Video Noise

Off Film Mode (Auto)

12:00 AM

Everyday PIP Souce

PIP Menu

Stereo

Off

30%

50%

50%

50%

50%

50%

High

Standard

On

Ant-A Ch-3

SQV

V-Chip Lock Menu

Lock by Time

Lock Time

N/A Input

Channel

On

N/A Magenta

PerfectColor™

Ant-A PIP Position

003 POP Position

PIP/POP Format

50% Forma t

Lower Rt.

Rt. Half

Dble W in.

Stretch

Page 21

Function

Contrast

Brightness

Sharpness

Color

Tint

Color Temp.

Video Noise

Film Mode

Bass

Treble

Balance

Surround

Listen To

Level Sound

MODEL: WD-52327 / WD-62327

A/V Memory Defaults

Ant -A/B DTV Comp-1/2 Input 1/2/3 MonoLink

Maximum Maximum Maximum Maximum Maximum

Center

Center

Center

Center

Center

Center

Center

Center

Center

Center

Center

Center

Center

Center

Center

Center

High High High

Standard Standard Standard

Center

Center

High

Standard

Center

Center

High

Standard

On

Center

Center

Center

Off

Stereo

Off

On

Center

Center

Center

Off

N/A

Off

On

Center

Center

Center

Off

N/A

Off

On

Center

Center

Center

Off

N/A

Off

On

Center

Center

Center

Off

N/A

Off

C. A/V Memory

Each of the external inputs has its’ own Audio/Video Memory. A change in an A/V setting at a specific input is stored in memory for that specific input.

A/V Reset

1. The front panel AV Reset button initializes all A/V Memories.

2. The AV Reset in the user’s menu initializes only the selected input’s A/V Memory.

LED Indications

The three front panel LEDs provides an indication of the sets operation, and the possible cause of a malfunction.

Normal LED Indications

Power/Timer

LED

Status

Off

Green Blink

Off

Green

Slow Green Blink

Off

Off

Off

Off

Off

Lamp Condition

Off

Off

Off (standby)

µPC Initializing (after AC off/on) (1~2 sec)

Blink green Lamp Fan running (1 min after PTV Off)

Off

Off

Power On

Power On Timer is set.

Abnormal LED Indications

Power/Timer

LED

Status

Off

Off

Off

Off

Off

Off

Yellow

Off

Off

Blink Yellow

Off

Blink Red

Red

Lamp Condition

Off

Yellow

Temp. high - dirty filter/excess room temp.

4000 hrs. Lamp usage warning

Blink Yellow Lamp Cover open

Off Air Filter Cover open

Red

Off

Off

Lamp failure (failed to turn On or broken)

Fan Stopped

Circuit failure (short) or DVI cable disconnected

Page 22

MODEL: WD-52327 / WD-62327

LED Diagnostic Check

1. Initial Control Circuitry Check

Immediately after the TV is connected to an AC power source:

2. Error Code Operational Check

Pressing the front panel “INPUT” and “MENU” buttons at the same time, and holding for 5 seconds, activates the Error Code Mode. The ” Power LED” flashes denoting a two digit Error Code, or indicating no problem has occured since the last Initalization.

Note: The front panel buttons must used, NOT those on the Remote Control.

• The number of flashes indicates the value of the MSD (tens digit) of the Error Code.

• The flashing then pauses for approximately 1/2 second.

• The LED then flashes indicating the value of the LSD (ones digit) of the Error Code.

• The Error Code is repeated a total of 5 times.

Example: If the Error Code is “34”, the LED will flash 3 times, pause, and then flash 4 times.

3. Error Codes

The Error Code designations indicating a malfunction, or no malfunction, are listed below:

ERR0R CODES

Error

Code

12

32

33

34

36

37

38

39

41

44

Description

No Error detected, check Power Supply

Lamp Cover is open

Air Filter Cover is open

Lamp abnormality

Light Engine (DMD or LAMP Fan stopped)

Exhaust or Lamp Ballast Fan stopped

Lamp temperature high

DMD temperature high

Short is detected

DVI cable between FMT & Engine disconnected.

Circuit Adjustment Mode

Most of the adjustments can only be performed using the remote hand unit.

A. Activating the Circuit Adjustment Mode

1. Select the signal source.

2. Press the "MENU" button on a remote hand unit.

3. Press the number buttons "5", "7", "5", "7" in sequence. The screen will change to the Adjustment Mode.

Note: Repeat steps 1 and 2 if the circuit adjustment mode does not appear on screen.

Page 23

MODEL: WD-52327 / WD-62327

B. Selection of adjustment Functions and

Adjustment Items

To select an adjustment item in the circuit adjustment mode, first select the adjustment function that includes the specific item to be adjusted. Then select that adjustment item.

Refer to the following pages for the listing of adjustment functions and adjustment items.

1. Press the "AUDIO" button on a remote hand unit to select an adjustment function. Each time the button is pressed, the Function changes in the following sequence:

MAIN MATR

DDP

Adjustment Functions

FPGA

SUB MATR

MISCDEV

2. Press the “VIDEO” button to select a specific

Adjustment Item. The Item number increases each time the “VIDEO” button is pressed.

C. Changing Data

After selecting an adjustment Item, use the “ADJUST UP/DOWN” buttons to change data.

• Press “ADJUST DOWN” to decrease the data value.

• Press “ADJUST UP” to increase the data value.

D. Saving Adjustment Data

Press “ENTER” to save adjustment data in memory. The character display turns red for approximately one second in this step.

Note: If the circuit adjustment mode is terminated without pressing “ENTER”, changes in adjustment data are not saved.

E. Terminating the Circuit Adjustment Mode

Press the “MENU” button on the remote hand unit twice to terminate the adjustment mode.

Note: The circuit adjustment mode can also be terminated by turning power OFF.

Page 24

MODEL: WD-52327 / WD-62327

List of Service Adjustment Items

MAIN MATRIX

(Main Decoder)

Item No.

Abbrev,

39

41

Stored in IC2K02 on PWB-TERMINAL

Description Data Range Initial Data

SCNT Main Y-Gain

SCLR Main CB/CR Gain

0~31

0~31

16

22

SUB MATRIX

(Sub Decoder)

Item No.

Abbrev,

39

41

SCNT

SCLR


Description

Sub Y-Gain

Sub CB/CR Gain

Data Range Initial Data

0~31

0~31

15

21

FPGA Stored in IC7C01 on PWB-SIGNAL

Item No.

Abbrev,

1 H-DLY

Description

Horiz. Position

2 V-DLY Vertical Position

Data Range Initial Data

0~128 74

0~55 32

DDP Function

Item # Abbrev.

120 GGH

121

122

123

GRH

GBH

GGM

124

125

126

127

128

GRM

GBM

GGL

GRL

GBL

Description

High Temp. Green Gain

High Temp. Red Gain

High Temp. Blue Gain

Mid Temp. Green Gain

Mid Temp. Red Gain

Mid Temp. Blue Gain

Low Temp. Green Gain

Low Temp. Red Gain

Low Temp. Blue Gain

NOTE: Data values are in hexadecimal format


Data Initial Data

Range WD-52327 WD-62327

000~400

"

2FA

400

31F

400

"

"

36D

2E1

34F

2FE

"

"

"

"

"

400

320

2C8

400

2D4

400

2FF

2EC

400

2C0

Page 25

MODEL: WD-52327 / WD-62327

Activating & Selecting an Internal

Test Signal

1. Select an External Input with no signal.

2. Press the buttons “MENU”-“5”-“7”-“5”-“7” in sequence. (Activates the Service Menu)

3. Select the “FPGA” function (AUDIO button)

5. Press “9” to return to the Service Menu.

6. Press “MENU” to exit the Service Mode.

CAUTION

DO NOT press “MENU” (or HOME) without pressing “9” first. (The Video Mute function will not function properly.)

To correct the Mute function -- remove AC to the TV, then reapply AC to reset the unit.

Page 26

[Video Circuit]

1. Main/Sub Y Level

Measuring

Instrument

Test Point

Ext. Trigger

Measuring

Range

Input Signal

Input Terminal

Oscilloscope

JA-22 & JB-3

------

------

Color Bars

Video Input

CIRCUIT ADJUST MODE

Activate …….. MENU-5-7-5-7

Function …...………..AUDIO

Item No. ……….…….VIDEO

Adjus t Data ….…….ADJUST

Save Data …. ………ENTER

Exit …………..MENU (twice)

MODEL: WD-52327 / WD-62327

Purpose: To set picture luminance

Symptom: Excess or insufficient brightness.

1. Supply a color bar signal to a Video Input (not an RF input).

2. Select the color bar signal for both the main and sub pictures.

3. Connect the oscilloscope to connector JA pin 22. (Main-Y)

4. Activate the Adjustment Mode (MENU-5-7-5-7)

5. Select the “MAIN MTRX” function. (AUDIO button)

6. Select adjustment Item “39 SCNT”. (VIDEO button)

7. Adjust the data for 0.71 ~ 0.76 Vp-p at JA pin 22.

(If it cannot be adjusted within this range, set to the lower value)

8. Move the oscilloscope to connector JB pin 3. (Sub-y)

9. Select the “SUB MTRX” function. (AUDIO button)

10. Select adjustment Item “39 SCNT”. (VIDEO button)

11. Adjust the data to equal the MAIN-Y Gain (+0.0V -0.05V).

12. Press “ENTER” to save data changes.

[Video Circuit]

2. Main/Sub Color Level

Measuring

Instrument

Test Point

Oscilloscope

JA-20 & JB-5

Ext. Trigger ------

Measuring

Range

Input Signal

200mV/div

20usec/div

Color Bars

Input Terminal

Video Input

Purpose:

Symptom:

To set the sub picture color level.

Main and sub pictures color levels differs.

1. Supply a color bar signal to a Video Input.

2. Select the color bar signal as the source for both the main and sub picture.

3. Connect an oscilloscope to connector JA pin 20 (main Cr).

3. Activate the Adjustment mode (MENU-5-7-5-7)

4. Select the “MAIN MTRX” function (AUDIO button).

5. Select adjustment item “41 SCLR” (VIDEO button)

6. Adjust the data for 0.81 ~ 0.86 Vp-p min. at JA pin 20.

(If it cannot be adjusted within this range, set to the lower value).

7. Move the oscilloscope to connector JB pin 5 (sub Cr).

8. Select the “SUB MTRX” function (AUDIO button).

9. Select adjustment item “41 SCLR” (VIDEO button).

10. Adjust data so the Sub Cr amplitude equals that of the Main Cr.

11. Press “ENTER to save data changes.

Page 27

[Video Circuit]

3. White Balance

Measuring

Instrument

Test Point

Ext. Trigger

Measuring

Range

Input Signal

Input Terminal

------

------

White Raster

Video Input





Adjus t Data ….…….ADJUST


Exit …………..MENU (twice)

MODEL: WD-52327 / WD-62327

Purpose:

To set high, mid and low temperature white levels.

Symptom:

White areas have a color tint.

1. Supply a 100% white raster to an External Video Input.

3. Activate the Service Mode. (MENU-5-7-5-7)

4. Select the “DDP” function. (AUDIO button)

5. Select adjustment Items with the VIDEO button.

NOTE: Data is displayed in the hexadecimal format.

6. Adjust the data for Items “120 GGH”, “121 GRH and “122 GBH” for optimum white at the center of the screen.

7. Adjust the data for Items “123 GGM”, “124 GRM and “125 GBM” for optimum white at the center of the screen.

8. Adjust the data for Items “126 GGL”, “127 GRL and “128 GBL” for optimum white at the center of the screen.

9. Press “ENTER” to save data changes.

10. Press “MENU” twice to exit the Service Mode.

[PICTURE POSITION]

4. Horizontal/Vertical Position

Measuring

Instrument

Test Point

Ext. Trigger

Measuring

Range

Input Signal

Input Terminal

----

----

------

-------

Internal Pattern “B”

External Input

Purpose:

Symptom:

To center picture on the screen.

Picture is off center.

NOTE: The TV must be on a flat level surface.

1. Select an External Input with no signal.

2. Press “MENU-5-7-5-7” in sequence (activates the Service Mode).

3. Press “AUDIO” to select the “FPGA” function.

4. Press “2” to activate internal Test Pattern B. (Shown below)

5. Use the “VIDEO” button to select Item “1 H-DLY”.

6. Use the “ADJUST” buttons to center the picture Horizontally..

7. Press “ENTER” to save the adjustment.

8. Use the “VIDEO” button to select Item “2 V-DLY”.

9. Use the “ADJUST” buttons to center the picture Vertically.

10. Press “ENTER” to save the adjustment.

11. Press “9” to terminate the test pattern.

12. Press “Menu” twice to terminate the Adjustment Mode.





Adjust Data ….…….ADJUST


Exit ………….."9" then "MENU"

Page 28

MODEL: WD-52327 / WD-62327

Mechanical Adjustments

• To perform the mechanical adjustments, the TV must be on a flat level surface and a certain amount of disassembly is required.

• Use internal Test Pattern B for all mechanical adjustments.

Front Disassembly

Refer to the diagram below for the Front Panel removal procedures.

Rear Disassembly

Refer to the to the diagrams below for the COVER-BACK and Rear Plate removal.

NOTE: To operate the TV with the COVER-BACK removed, the FILTER-COVER must be reinstalled and the Exhaust Fan connected.

Page 29

MODEL: WD-52327 / WD-62327

Picture Rotation Adjustment

NOTE: The TV must be on a flat level surface.

1. From the front of the TV, lift the foam to access and loosen slightly, the brass Rotation Locking Screws on the Adjuster

Assembly, Figure 4A. (Use a 10mm wrench.)

2. From the rear of the TV, access the black Rotation Adjustment screw and adjust so the test pattern center lines are parallel to the sides, top and bottom of the screen frame, Figure 4B. (Use a mirror to veiw the picture from the rear of the set.)

3. Tighten the two Locking Screws. Use Locktite to secure the Adjustment Screw. (If necessary, use the electrical adjustments to center the picture)

Page 30

Keystone Adjustment

MODEL: WD-52327 / WD-62327

Horizontal Keystone Distortion

Vertical Keystone Distortion

NOTE: The TV must be on a flat level surface

1. From the front of the TV, loosen the two Keystone Locking Screws in the small mirror assembly. (10mm wrench)

2. From the front of the TV, adjust the Horizontal Keystone Adjustment for minimum distortion.

3. From the front of the TV, adjust the Vertical Keystone Adjustment for minimum distortion.

4. Tighten the Keystone Lock Screws. and secure the adjustment screws with Locktite. (If necessary, use the electrical adjustments to center the picture)

Horiz

Keystone

Adjust

Vertical

Keystone

Adjust

Locking Screws

Small Mirror Assembly (Front View)

Page 31

MODEL: WD-52327 / WD-62327

QUICK REFERENCE FOR COMMON REPLACEMENT PARTS

• Critical Electrical Components are indicated by Bold Type in the Parts List

Part Na m e

Lam p Cartridge

Dust Filter

Remote Control

Part Na m e

Optical Engine

Lam p Ballast

Power PW B

Signal PW B

Format PW B

Terminal PW B

Sub Power PW B

Audio PW B

Remote Preamp

Front PW B

Control PW B

Right Speaker PW B

Left Speaker PW B

Lam p Fa n

DMD Fa n

Balla st Fa n

Exhaust Fa n

DMD Thermal Sensor

Lamp Cover Detect Switch

Filter Cover Detect Switch

Part Na m e

Lenticular Screen

Fresnel Lens

Bezel

Customer Replaceable Parts

Description W D-52327

LAMP-CARTRIDGE

FILTER-DUST

REMOTE

915P020010

620D144010

260P116010

Service Parts

Description

OPTICAL-ENGINE

UNIT-POW ER-LAMP

ASSY-PW B-POW ER

ASSY-PW B-SIGNAL

ASSY-PW B-FMT

ASSY-PW B-TERMINAL

ASSY-PW B-POW ER-SUB

ASSY-PW B-AUDIO

ASSY-PW B-PREAMP

ASSY-PW B-FRONT

ASSY-PW B-CONTROL

ASSY-PW B-SPEAKER-R

ASSY-PW B-SPEADER-L

FAN-LAMP

FAN-DMD

FAN-BALLAST

FAN-EXHAUST

SENSOR-THERMAL

SW -MICRO

SW -MICRO

Screen Parts

Description

LENS-LENTICULAR

LENS-FRESNEL

BEZEL-FRONT

W D-52327

491P176030

491P175010

761A252010

W D-52327

939P977010

939B978010

930B929001

930B930001

930B931001

930B932001

934C148001

934C149001

935D811001

935D812001

935D813001

935D814001

935D815001

299P282010

299P283010

299P278020

299P103050

299P280010

436P021010

436P021010

W D-62327

915P020010

620D144010

260P116010

W D-62327

939P977020

939B978010

930B929001

930B930001

930B931001

930B932001

934C148001

934C149001

935D811001

935D812001

935D813001

935D814001

935D815001

299P282010

299P283010

299P278020

299P103050

299P280010

436P021010

436P021010

W D-62327

491P176040

491P175020

761A253010

PAGE 32

MODEL: WD-52327 / WD-62327

Model Legend: [a] WD-52327, [b] WD-623275

Ref # Part # Part Name & Description [#] Ref # Part # Part Name & Description

INTEGRATED CIRCUITS

IC2D00 270P974010 IC-C-MOS - SII907B

IC2D02 261P135010 FET-HEX - IRF7313

IC2D04 271P004010 IC - CM1208-08MS

IC2K01 270P623010 IC - CXA2069Q

IC2K02 275P533010 IC-C-MOS - M24C64WM6T

IC2K04 275P718010 IC-C-MOS - TC74HC4053FT

IC2K05 275P718010 IC-C-MOS - TC74HC4053FT

IC2L01 275P937010 IC-C-MOS - MM1519XQ

IC2M01 275P947010 IC-C-MOS - UPD64083

IC2M02 270P992020 IC - BA25BC0FP

IC2MD1 272P379020 IC - LM1881MX (NSC)

IC2N01 275P938010 IC-C-MOS - TA1340F

IC2P01 275P938010 IC-C-MOS - TA1340F

IC2R01 271P005020 IC - AN15851AN

IC3A01 275P731020 IC-C-MOS - MSP3445G-QI-B8-V3

IC3E00 271P080010 IC - TDA8922J

IC3J01 270P838010 IC-C-MOS - NJM2520M

IC3J02 270P838010 IC-C-MOS - NJM2520M

IC3J03 270P838010 IC-C-MOS - NJM2520M

IC3J04 270P838010 IC-C-MOS - NJM2520M

IC7A00 276P017070 IC-C-MOS - M306V7FGFP-VK26

IC7A02 270P706020 IC - MAX823REUK

IC7A03 275P786010 IC-C-MOS - TC7SA08FU

IC7A05 271P023010 IC - SN74CBTD1G125DBVR

IC7A06 271P023010 IC - SN74CBTD1G125DBVR

IC7AAA 275P981010 IC-C-MOS - 24LCS22AT/SN

IC7C01 275P533010 IC-C-MOS - M24C64WM6T

IC7D01 275P278010 IC-C-MOS - TC74LVX14FT

IC7D02 270P818020 IC - CXA3506R

IC7D03 267P172010 HIC - AF-9395A

IC7E00 275P451010 IC-C-MOS - TC74HC4066AFN

IC7E01 275P560010 IC-C-MOS - ADS931E

IC7E02 275P560010 IC-C-MOS - ADS931E

IC7E03 275P560010 IC-C-MOS - ADS931E

IC7H00 275P963010 IC-C-MOS - DPM5

IC7H07 270P992010 IC - BA18BC0FP

IC7M00 275P982010 IC - MT48LC2M32B2-7

IC7N01 270P348010 IC - TLC2932IPW

IC7N11 275P236020 IC-C-MOS - TC74LVX244FT

IC7N21 275P769010 IC-C-MOS - TC74AC157FT

IC7N31 275P769010 IC-C-MOS - TC74AC157FT

IC7N41 274P901010 IC-C-MOS - TC74HCT7007AF

IC7N61 274P901010 IC-C-MOS - TC74HCT7007AF

IC8C03 275P689010 IC-C-MOS - ICS551MT

IC8D01 271P112010 IC - IP00C722

IC8D02 275P982010 IC - MT48LC2M32B2-7

IC8E00 276P107010 IC-C-MOS - SiI164

IC8E02 270P879030 IC - SC1566I5M-2.5TR

IC8E03 270P879030 IC - SC1566I5M-2.5TR

IC8E04 271P010010 IC - RT9172-18CG

IC8E05 271P010010 IC - RT9172-18CG

IC8H01 271P113010 IC - XC2S50E-6PQ208C

IC8H02 271P114020 IC - XCF01SVO20C-K261

IC9A10 267P175010 HIC - STR-W6735

IC9A12 271P081010 IC - BA00CC0WFP

IC9A20 270P816010 IC - NJM431L

IC9A21 270P991010 IC - IRU3037CS

IC9AAA 270P677010 IC - BA033FP

IC9C01 270P928010 IC - BA17809FP

IC9C11 270P928010 IC - BA17809FP

IC9C20 267P164010 HIC - TNY264P

IC9C21 270P677010 IC - BA033FP

IC9C21 270P816010 IC - NJM431L

IC9C31 270P999010 IC - NJM2370R09

IC9C61 270P677010 IC - BA033FP

TRANSISTORS

CHIP Type Transistors (Listed by Part No.)

Part No.

Description

260P806010 DTA124EK/UN2112

260P817010 2SA1037K-Q

260P817050 2SA1037K-R,S/2SB709AI-R,S

260P817080 2SA1037K-R,S

260P818010 2SC2412K-Q

260P818050 2SC2412K-R,S/2SD601AI-R,S

260P835030 2SC2413K-Q

260P846030 DTC143ZKAT146

TRANSISTORS

Conventional Transistors (By Ref #)

Ref # Part # Part Name & Description

Q9A20 261P135010 FET-HEX - IRF7313

Q9A70 261P101010 TR - PHP21N06T

Q9B70 261P101010 TR - PHP21N06T

DIODES

D2J91 262P075010 DIODE - RSB6.8S

D7A00 264P828010 D-CHIP - DAN202U/MA142WK

D7AAA 262P805050 D-CHIP - UDZS5.1B

D7L20 262P075010 DIODE - RSB6.8S

D7L21 264P212020 D-LED - LN31GPH

D7L22 264P584020 DIODE-LE - SML1216W-C,D

D7L23 264P584020 DIODE-LE - SML1216W-C,D

D7L24 262P075010 DIODE - RSB6.8S

D7L25 262P075010 DIODE - RSB6.8S

D7L26 262P075010 DIODE - RSB6.8S

D7L27 262P075010 DIODE - RSB6.8S

D9A00 262P031010 DIODE - D6SB80

D9A01 262P031010 DIODE - D6SB80

D9A02 264P045080 DIODE - 1S2076A/1S2471OM

D9A03 264P461050 DIODE - EQA02-06B/RD5.6EB3

D9A04 264P045080 DIODE - 1S2076A/1S2471OM

D9A05 264P899010 DIODE - BYV26E

D9A06 264P045080 DIODE - 1S2076A/1S2471OM

D9A18 264P045080 DIODE - 1S2076A/1S2471OM

D9A19 264P045080 DIODE - 1S2076A/1S2471OM

D9A20 264P045080 DIODE - 1S2076A/1S2471OM

D9A23 264P045080 DIODE - 1S2076A/1S2471OM

D9A24 264P045080 DIODE - 1S2076A/1S2471OM

D9A25 264P045080 DIODE - 1S2076A/1S2471OM

D9A26 262P066010 DIODE - RU4A

D9A27 262P066010 DIODE - RU4A

D9A28 264P045080 DIODE - 1S2076A/1S2471OM

D9A29 264P045080 DIODE - 1S2076A/1S2471OM

D9A30 264P470070 DIODE - EQA02-32B/RD33EB3



PAGE 33

[#]

[#] Model Legend: [a] WD-52327, [b] WD-62327


D9A33 264P458050 DIODE - RD3.9EB1

D9A34 262P090010 DIODE - M1FP3






D9A60 264P669030 DIODE - S3L20U

D9A61 264P669030 DIODE - S3L20U





D9C22 264P825040 DIODE - ERA15-08

D9C24 264P045080 DIODE - 1S2076A/1S2471OM

D9C30 262P097010 DIODE - 11EQS06N-TA2B5

D9C31 262P097010 DIODE - 11EQS06N-TA2B5

COILS

L1A30 321C114010 COIL-RF - 2200MH-J

L1A31 325C461030 COIL-PEAKING - 10MH-K

L1B30 321C114010 COIL-RF - 2200MH-J

L1B31 325C461030 COIL-PEAKING - 10MH-K

L2AGA 409P864010 EMI-F-CHIP - ACB2012M600

L2AJA 409P864010 EMI-F-CHIP - ACB2012M600

L2AKA 409P864010 EMI-F-CHIP - ACB2012M600

L2ANA 409P864010 EMI-F-CHIP - ACB2012M600

L2APA 409P864010 EMI-F-CHIP - ACB2012M600

L2ARA 409P864010 EMI-F-CHIP - ACB2012M600

L2ATA 409P864010 EMI-F-CHIP - ACB2012M600

L2AYA 409P864010 EMI-F-CHIP - ACB2012M600

L2AZA 409P864010 EMI-F-CHIP - ACB2012M600

L2K05 409P777080 EMI-F-CHIP - BLM21P221S

L2K42 325C461030 COIL-PEAKING - 10MH-K

L2K46 325C462080 COIL-PEAKING - 180MH-J

L2K55 325C462080 COIL-PEAKING - 180MH-J

L2L28 325C461030 COIL-PEAKING - 10MH-K

L2M22 325C461050 COIL-PEAKING - 15MH-K

L2M31 409P777080 EMI-F-CHIP - BLM21P221S





L2M50 325C461000 COIL-PEAKING - 5.6MH-K



L2MA0 325C461050 COIL-PEAKING - 15MH-K

L2MA1 325C461030 COIL-PEAKING - 10MH-K

L2MD1 325C461030 COIL-PEAKING - 10MH-K

L2N01 325C461030 COIL-PEAKING - 10MH-K

L2N25 325C462020 COIL-PEAKING - 56MH-K

L2NA1 325C461030 COIL-PEAKING - 10MH-K



L2NC0 325C461030 COIL-PEAKING - 10MH-K

L2NC1 325C461080 COIL-PEAKING - 27MH-K

L2P01 325C461030 COIL-PEAKING - 10MH-K




MODEL: WD-52327 / WD-62327

[#] Ref # Part # Part Name & Description



L2R28 325C461030 COIL-PEAKING - 10MH-K

L3A10 409P923060 EMI-F-CHIP - BLM21B272S


L3E25 325C502010 COIL-CHIP - SLF12575T-330M3R2-H

L3E26 325C502010 COIL-CHIP - SLF12575T-330M3R2-H

L3E51 411D009020 CORE-FERRITE - ZBF503D-01

L3E52 411D009020 CORE-FERRITE - ZBF503D-01

L3J01 325C461030 COIL-PEAKING - 10MH-K

L3J20 325C461030 COIL-PEAKING - 10MH-K

L3J40 409P777020 EMI-F-CHIP - BLM21A05



























L7ACC 409P777080 EMI-F-CHIP - BLM21P221S

L7D30 325C241030 COIL-CHIP - 10MH-K



L7D42 409P777080 EMI-F-CHIP - BLM21P221S


L7E00 409P777080 EMI-F-CHIP - BLM21P221S






L7H01 409P777080 EMI-F-CHIP - BLM21P221S






L7J13 409P777080 EMI-F-CHIP - BLM21P221S




PAGE 34

[#]

MODEL: WD-52327 / WD-62327



L7K01 409P777080 EMI-F-CHIP - BLM21P221S


L7N01 409P777080 EMI-F-CHIP - BLM21P221S







L7RF1 409P777050 EMI-F-CHIP - BLM21B201S

L8C02 409P964010 EMI-F-CHIP - BK2125HS102

L8C04 409P964010 EMI-F-CHIP - BK2125HS102

L8C09 409P938020 EMI-F-CHIP - BK1608 LL121







L8D04 409P964010 EMI-F-CHIP - BK2125HS102














L9A01 411P011010 FERITE-BEADS - ZBF-503S-P

L9A02 411P011010 FERITE-BEADS - ZBF-503S-P

L9A10 321C151070 COIL-RF - 22MH-K

L9A19 321C141010 COIL-RF - 6.8MH-M

L9A20 321C141010 COIL-RF - 6.8MH-M

L9A21 321C141010 COIL-RF - 6.8MH-M

L9A22 321C141030 COIL-RF - 10MH-K

L9A23 321C141030 COIL-RF - 10MH-K

L9A30 321C140060 COIL-RF - 2.7MH-M

L9A31 321C140060 COIL-RF - 2.7MH-M

L9A32 321C140060 COIL-RF - 2.7MH-M

L9A33 351P250010 COIL-CHOKE - GSTC6018-100M

L9A62 321C141010 COIL-RF - 6.8MH-M

L9A63 321C141090 COIL-RF - 33MH-K

L9A64 321C141090 COIL-RF - 33MH-K

L9A70 321C141090 COIL-RF - 33MH-K

L9A71 321C141090 COIL-RF - 33MH-K

L9AAA 325C462020 COIL-PEAKING - 56MH-K

L9B70 321C141090 COIL-RF - 33MH-K

L9C20 321C141070 COIL-RF - 22MH-K

L9C21 321C141070 COIL-RF - 22MH-K

L9D00 351P268010 LINE-FILTER - HF3545-502Y5R0-TXXBH



LC1A10 409P875090 EMI-F-CHIP - ELKE103FA

LC1A11 409P876020 EMI-F-CHIP - CNF20C470S/CKD510JB1H470S


[#]
















LC2J40 409P777020 EMI-F-CHIP - BLM21A05













LC7A00 409P865060 EMI-F-CHIP - BLM11B141S

LC7A01 409P865060 EMI-F-CHIP - BLM11B141S
















LC7D02 409P777080 EMI-F-CHIP - BLM21P221S

LC7D10 409P876020 EMI-F-CHIP - CNF20C470S/CKD510JB1H470S





LC7E10 409P876020 EMI-F-CHIP - CNF20C470S/CKD510JB1H470S









PAGE 35

MODEL: WD-52327 / WD-62327


Ref # Part # Part Name & Description [#]











LC8E29 409P875090 EMI-F-CHIP - ELKE103FA

LC8E30 409P875090 EMI-F-CHIP - ELKE103FA











TRANSFORMERS

T9A10 350P830010 TRANS-PWR - SRW39LEC-U10V117

T9C20 350P806010 TRANS-PWR - ETS19AB1R5BG

VARIABLE RESISTORS

RV9D00 265P100020 VAR - ERZV10D271CS

RV9D01 265P100020 VAR - ERZV10D271CS

RESISTORS

CHIP Type Resistors (Listed by Value)

Part No.

Value Part No.

103P509050

103P508040

1/16W 0OHM

1/16W 2.2-J

103P492060

103P502060

103P509000

103P400050

103P910050

103P500050

103P500070

1/16W 6.8-J

1/10W 22-J

1/16W 22-J

1/16W 22-J

1/16W 33-J

103P492080

103P492090

103P502070

103P472090

103P493000

103P500080

103P910090

103P400090

103P500090

103P501000

103P501010

103P794060

103P509090

103P501020

103P401030

1/16W 39-J

1/16W 47-J

1/10W 47-J

1/16W 47-J

1/16W 56-J

1/16W 68-J

1/16W 75-F

1/16W 75-J

1/16W 82-J

1/10W 100-J

103P502080

103P493020

103P493030

103P502090

103P493050

103P503000

103P493060

103P493070

103P503010

103P493090

103P501030

103P501040

103P401050

103P490050

103P501050

103P501060

103P501070

103P470090

1/16W 100-J

1/16W 120-J

1/10W 150-J

1/16W 150-F

1/16W 150-J

1/16W 180-J

1/16W 220-J

1/8W 220-F

103P503020

103P503030

103P494030

103P503040

103P503050

103P503060

103P494080

103P494090

Value

1/16W 1.1K-F

1/16W 1.2K-J

1/16W 1.3K-F

1/16W 1.5K-F

1/16W 1.5K-J

1/8W 1.5K-F

1/16W 1.6K-F

1/16W 1.8K-J

1/16W 2K-F

1/16W 2.2K-F

1/16W 2.2K-J

1/16W 2.7K-F

1/16W 2.7K-J

1/16W 3K-F

1/16W 3.3K-F

1/16W 3.3K-J

1/16W 3.9K-F

1/16W 3.9K-J

1/16W 4.7K-J

1/16W 5.6K-F

1/16W 5.6K-J

1/16W 6.8K-J

1/16W 8.2K-J

1/16W 9.1K-F

1/16W 10K-F


103P491000

103P501080

103P401080

103P491020

103P501090

103P491040

103P491050

103P502000

103P491060

103P491070

103P502010

103P491090

103P502020

103P492000

103P492010

103P502030

103P505090

103P492030

103P502040

103P492050

103P502050

1/16W 240-F

1/16W 270-J

1/10W 270-J

1/16W 300-F

1/16W 330-J

1/16W 360-F

1/16W 390-F

1/16W 390-J

1/16W 430-F

1/16W 470-F

103P503070

103P495010

103P503080

103P503090

103P504000

103P504010

103P496000

103P496010

103P504030

103P504040

1/16W 470-J

1/16W 560-F

1/16W 560-J

1/16W 620-F

1/16W 680-F

1/16W 680-J 103P505000

1/16W 680K-J 103P505010

1/16W 820-F

1/16W 820-J

1/16W 1K-F

103P505050

103P506000

103P506010

1/16W 1K-J

103P504050

103P504060

103P504070

103P504080

103P504090

RESISTORS

Conventional Resistors (By Ref #)


R2J21 109D151050 R-CARBON - 1/4W 75-J

R2J31 109D151050 R-CARBON - 1/4W 75-J

R3E27 109D151030 R-CARBON - 1/4W 4.7-J

R3E28 103C170050 R-METAL - 1W 22-J

R3E29 109D151030 R-CARBON - 1/4W 4.7-J

R3E30 109D151030 R-CARBON - 1/4W 4.7-J

R3E31 109D151030 R-CARBON - 1/4W 4.7-J

R3E32 103C170050 R-METAL - 1W 22-J

R9A01 109P179010 R-CEMENT-PLATE - 6.8-J

R9A02 109P179010 R-CEMENT-PLATE - 6.8-J

R9A03 109C010010 R-COMP - 1/2W 1M-K

R9A05 109C010010 R-COMP - 1/2W 1M-K

R9A06 109C010010 R-COMP - 1/2W 1M-K

R9A09 103P145030 R-CARBON - 1/2W 220K-J

R9A11 103P145030 R-CARBON - 1/2W 220K-J

R9A13 103C194090 R-METAL - 3W 100K-J

R9A14 103C194090 R-METAL - 3W 100K-J

R9A15 103C394020 R-METAL-P - 3W 27K

R9A16 103P145020 R-CARBON - 1/2W 180K-J

R9A17 103P145020 R-CARBON - 1/2W 180K-J

R9A18 103P145020 R-CARBON - 1/2W 180K-J

R9A19 103P144020 R-CARBON - 1/2W 27K-J

R9A20 103P144020 R-CARBON - 1/2W 27K-J

R9A21 103C177040 R-METAL - 1W 0.33-J

R9A22 103C177040 R-METAL - 1W 0.33-J

R9A25 103P142050 R-CARBON - 1/2W 1K-J

R9A26 109D151060 R-CARBON - 1/4W 68-J

R9A27 109D151050 R-CARBON - 1/4W 75-J

R9A66 103P712000 R-CARBON - 1/4W 390-J

R9A67 103P712000 R-CARBON - 1/4W 390-J

R9A68 103P712000 R-CARBON - 1/4W 390-J

R9A69 103P712000 R-CARBON - 1/4W 390-J

R9A76 103C392010 R-METAL-P - 3W 470-J

R9A77 103C392010 R-METAL-P - 3W 470-J

[#]

1/16W 10K-J

1/16W 12K-F

1/16W 12K-J

1/16W 15K-J

1/16W 18K-J

1/16W 22K-J

1/16W 30K-F

1/16W 33K-F

1/16W 33K-J

1/16W 39K-J

1/16W 47K-J

1/16W 56K-J

1/16W 68K-J

1/16W 82K-J

1/16W 100K-J

1/16W 120K-J

1/16W 150K-J

1/16W 330K-J

1/16W 820K-J

1/16W 1M-J

[#]

PAGE 36

MODEL: WD-52327 / WD-62327



R9A89 103P141090 R-CARBON 1/2W 330-J

R9A90 103C394020 R-METAL-P - 3W 27K

R9A91 103C394020 R-METAL-P - 3W 27K

R9A92 103C288040 R-METAL-CP - 2W 2.2-J

R9C20 103C391020 R-METAL-P - 3W 82-J

R9C21 103P712050 R-CARBON - 1/4W 1K-J

R9C23 103P710090 R-CARBON - 1/4W 47-J

R9C24 103P142070 R-CARBON - 1/2W 1.5K-J

R9C25 103P462050 R-METAL - 1/4W 1K-F

R9C26 103P462050 R-METAL - 1/4W 1K-F

R9C27 103P712050 R-CARBON - 1/4W 1K-J

R9C28 103P713070 R-CARBON - 1/4W 10K-J

R9C29 103P711030 R-CARBON - 1/4W 100-J

R9C30 103P710080 R-CARBON - 1/4W 39-J

R9D00 109D036020 R-COMP - 1/2W 4.7M-K

CAPACITORS

CHIP Type Capacitors (Listed by Value)

Part No.

154P340040

154P341010

154P351020

154P341030

Value

50V 3P-C

CH50V 10P-C

SL50V 10P-J

CH50V 12P-J

Part No.

141P143080

141P133080

141P132030

141P142090

154P341050

154P341090

154P342010

154P342030

154P342070

154P342090

154P353000

154P343050

141P140010

154P344050

CH50V 15P-J

CH50V 22P-J

CH50V 27P-J

CH50V 33P-J

CH50V 47P-J

CH50V 270P-J

141P143020

141P143030

141P144020

141P134090

141P139030

CH50V 56P-J 141P146040

SL50V 56P-J 141P138080

CH50V 100P-J 141P146080

B50V 220P-K 141P139090

181P526010

154P344070

141P140050

141P140060

154P345030

154P345050

154P345070

154P345010

141P140090

154P345090

141P141010

141P141030

CH50V 330P-J 141P147020

B50V 470P-K 141P134070

B50V 560P-K 181P526020

CH25V 560P-J 181P532030

CH25V 680P-J 181P508080

CH25V 820P-J 181P522030

CH50V 470P-J 181P530030

B50V 1000P-K 181P520030

CH25V 1000P-J 181P522060

B50V 1500P-K 181P502070

B50V 2200P-K 181P520040

181P500060

CAPACITORS AND TRIMMERS

Conventional Capacitors (By Ref #)


C1A13 181P352040 C-ELEC - 16V 100M-M

C1A21 181P352040 C-ELEC - 16V 100M-M

C1A24 181P352040 C-ELEC - 16V 100M-M

C1A26 172P262010 C-M-POLY - 50V 0.047M-J

C1B13 181P355090 C-ELEC - 50V 100M-M

C1B21 181P352040 C-ELEC - 16V 100M-M

C1B24 181P352040 C-ELEC - 16V 100M-M

C1B26 172P262010 C-M-POLY - 50V 0.047M-J

C2AGC 155P239040 C-CER - CH50V 100P-J

C2AGD 142P024060 C-CER - BF50V 0.1M-Z

[#]

Value

F50V 0.01M-Z

F50V 0.01M-Z

B50V 0.015M-K

B25V 0.047M-K

B16V 0.082M-K

B16V 0.1M-K

F25V 0.1M-Z

F50V 0.1M-Z

B25V 0.1M-K

B10V 0.22M-K

B25V 0.33M-K

B10V 0.47M-K

B16V 0.47M-K

50V 1M-M

B10V/6.3V 1M-K

B16V 1M-K

50V 2.2M-M

16V 10M-M

16V 10M-M

16V 10M-M 105C

6.3V 47M-M

6.3V 47M-M

6V 47M-M

16V 100M-M

6.3V 100M-M

6.3V 220M-M

C2AJB 142P024060 C-CER - BF50V 0.1M-Z

C2AJD 155P239040 C-CER - CH50V 100P-J

C2AKC 181P352040 C-ELEC - 16V 100M-M

C2AKD 155P239040 C-CER - CH50V 100P-J

C2ANC 142P024060 C-CER - BF50V 0.1M-Z

C2AND 155P239040 C-CER - CH50V 100P-J

C2APC 181P352040 C-ELEC - 16V 100M-M

C2APD 155P239040 C-CER - CH50V 100P-J

C2ARC 142P024060 C-CER - BF50V 0.1M-Z

C2ARD 155P239040 C-CER - CH50V 100P-J

C2ATC 142P024060 C-CER - BF50V 0.1M-Z

C2ATD 155P239040 C-CER - CH50V 100P-J

C2AYC 142P024060 C-CER - BF50V 0.1M-Z

C2AYD 155P239040 C-CER - CH50V 100P-J

C2AZC 142P024060 C-CER - BF50V 0.1M-Z

C2AZE 181P355050 C-ELEC - 50V 10M-M

C2AZF 155P239040 C-CER - CH50V 100P-J

C2K01 181P355050 C-ELEC - 50V 10M-M

C2K03 181P355050 C-ELEC - 50V 10M-M

C2K08 181P355050 C-ELEC - 50V 10M-M

C2K10 181P355050 C-ELEC - 50V 10M-M

C2K15 181P355050 C-ELEC - 50V 10M-M

C2K17 181P355050 C-ELEC - 50V 10M-M

C2K18 181P351060 C-ELEC - 10V 330M-M

C2K22 181P355050 C-ELEC - 50V 10M-M

C2K27 181P355050 C-ELEC - 50V 10M-M

C2K43 181P352030 C-ELEC - 16V 47M-M

C2K48 181P352030 C-ELEC - 16V 47M-M

C2K50 181P355050 C-ELEC - 50V 10M-M

C2K63 181P355050 C-ELEC - 50V 10M-M

C2K71 181P352030 C-ELEC - 16V 47M-M

C2K75 181P352030 C-ELEC - 16V 47M-M

C2L29 181P352030 C-ELEC - 16V 47M-M

C2L52 181P352030 C-ELEC - 16V 47M-M

C2M28 181P351080 C-ELEC - 10V 1000M-M

C2M29 181P351080 C-ELEC - 10V 1000M-M

C2M31 181P352030 C-ELEC - 16V 47M-M

C2M34 181P352030 C-ELEC - 16V 47M-M

C2M36 181P352030 C-ELEC - 16V 47M-M

C2M38 181P352030 C-ELEC - 16V 47M-M

C2M43 181P352030 C-ELEC - 16V 47M-M

C2M44 181P352030 C-ELEC - 16V 47M-M

C2M54 181P355050 C-ELEC - 50V 10M-M

C2M64 181P352030 C-ELEC - 16V 47M-M

C2M80 181P352030 C-ELEC - 16V 47M-M

C2M88 181P355010 C-ELEC - 50V 1M-M

C2M89 181P352030 C-ELEC - 16V 47M-M

C2M98 181P355050 C-ELEC - 50V 10M-M

C2MA4 181P352030 C-ELEC - 16V 47M-M

C2MA6 181P352030 C-ELEC - 16V 47M-M

C2MA9 181P352030 C-ELEC - 16V 47M-M

C2MC4 181P352030 C-ELEC - 16V 47M-M

C2MC8 181P352040 C-ELEC - 16V 100M-M

C2MD6 181P352040 C-ELEC - 16V 100M-M

C2MD7 181P352040 C-ELEC - 16V 100M-M

C2N03 181P352070 C-ELEC - 16V 470M-M

C2N27 181P350060 C-ELEC - 3V 1000M-M

C2NA6 181P355050 C-ELEC - 50V 10M-M

C2NC5 181P355050 C-ELEC - 50V 10M-M

C2P01 181P352070 C-ELEC - 16V 470M-M

PAGE 37

[#]

MODEL: WD-52327 / WD-62327



C2P26 181P350060 C-ELEC - 3V 1000M-M

C2P32 181P352030 C-ELEC - 16V 47M-M

C2P42 181P352030 C-ELEC - 16V 47M-M

C2R29 181P352030 C-ELEC - 16V 47M-M

C3A14 181P355050 C-ELEC - 50V 10M-M

C3A20 181P355050 C-ELEC - 50V 10M-M

C3A21 181P355050 C-ELEC - 50V 10M-M

C3A28 181P355050 C-ELEC - 50V 10M-M

C3A29 181P355050 C-ELEC - 50V 10M-M

C3A32 181P355050 C-ELEC - 50V 10M-M

C3A33 181P355050 C-ELEC - 50V 10M-M

C3A34 181P355030 C-ELEC - 50V 3.3M-M

C3A46 181P355050 C-ELEC - 50V 10M-M

C3A49 181P355050 C-ELEC - 50V 10M-M

C3E50 181P358070 C-ELEC - 63V 22M-M

C3E51 181P354090 C-ELEC - 35V 470M-M

C3E52 181P354090 C-ELEC - 35V 470M-M

C3E53 181P354090 C-ELEC - 35V 470M-M

C3E54 181P354090 C-ELEC - 35V 470M-M

C3F91 181P375050 C-ELE-BP-AUDIO - 25V 1000M-M

C3F92 181P375050 C-ELE-BP-AUDIO - 25V 1000M-M

C3J01 181P352030 C-ELEC - 16V 47M-M

C3J05 181P355050 C-ELEC - 50V 10M-M

C3J06 181P122070 C-ELEC-NP - 25V 10M-M

C3J09 181P355050 C-ELEC - 50V 10M-M

C3J10 181P122070 C-ELEC-NP - 25V 10M-M

C3J24 181P352030 C-ELEC - 16V 47M-M

C3K02 181P355010 C-ELEC - 50V 1M-M

C3K04 181P355010 C-ELEC - 50V 1M-M

C3K09 181P355010 C-ELEC - 50V 1M-M

C3K11 181P355010 C-ELEC - 50V 1M-M

C3K16 181P355010 C-ELEC - 50V 1M-M

C3K18 181P355010 C-ELEC - 50V 1M-M

C3K23 181P355010 C-ELEC - 50V 1M-M

C3K25 181P355010 C-ELEC - 50V 1M-M

C3K29 181P355010 C-ELEC - 50V 1M-M

C3K31 181P355010 C-ELEC - 50V 1M-M

C3K62 181P355010 C-ELEC - 50V 1M-M

C3K64 181P355010 C-ELEC - 50V 1M-M

C7A00 154P345050 C-CER-CHIP - CH25V 680P-J

C7A16 181P352030 C-ELEC - 16V 47M-M

C7A99 181P352030 C-ELEC - 16V 47M-M

C7ACB 181P355050 C-ELEC - 50V 10M-M

C7B02 181P355020 C-ELEC - 50V 2.2M-M

C7B88 181P355050 C-ELEC - 50V 10M-M

C7B96 181P355020 C-ELEC - 50V 2.2M-M

C7C56 181P352030 C-ELEC - 16V 47M-M

C7C57 181P352030 C-ELEC - 16V 47M-M

C7D00 181P352040 C-ELEC - 16V 100M-M

C7D97 181P352040 C-ELEC - 16V 100M-M

C7K01 181P352030 C-ELEC - 16V 47M-M

C7RF2 181P355050 C-ELEC - 50V 10M-M

C7S03 181P352030 C-ELEC - 16V 47M-M

C9A00 189P185090 C-CER - AC250V E2200P-M

C9A01 189P185090 C-CER - AC250V E2200P-M

C9A02 185D122050 C-ELEC - H200V 1000M-M

C9A03 185D122050 C-ELEC - H200V 1000M-M

C9A04 185D127040 C-ELEC - H450V 150M-M 105C

C9A05 189P185090 C-CER - AC250V E2200P-M

C9A06 189P185090 C-CER - AC250V E2200P-M


C9A08 189P185090 C-CER - AC250V E2200P-M

C9A09 189P185090 C-CER - AC250V E2200P-M

C9A10 189P185090 C-CER - AC250V E2200P-M

C9A11 189P185090 C-CER - AC250V E2200P-M

C9A12 189P153010 C-M-POLY - AC125/250V 0.33M-M

C9A13 189P152070 C-M-POLY - 250VAC 0.01M-M

C9A14 189P152070 C-M-POLY - 250VAC 0.01M-M

C9A15 189P185070 C-CER - AC250V E1000P-M

C9A16 189P185070 C-CER - AC250V E1000P-M

C9A20 154P262070 C-CER - R2KV820P-K

C9A21 181P185060 C-ELEC - 50V 10M-M 105C

C9A25 172P138010 C-POLY - 50V 4700P-J

C9A26 185D122050 C-ELEC - H200V 1000M-M

C9A27 185D122050 C-ELEC - H200V 1000M-M

C9A29 181P185060 C-ELEC - 50V 10M-M 105C

C9A30 181P185060 C-ELEC - 50V 10M-M 105C

C9A32 181P735040 C-ELEC - 25V 1500M-M

C9A33 181P735040 C-ELEC - 25V 1500M-M

C9A35 181P735010 C-ELEC - 25V 470M-M

C9A37 181P732040 C-ELEC - 10V 3300M-M 105C

C9A38 181P732040 C-ELEC - 10V 3300M-M 105C

C9A39 181P184070 C-ELEC - 35V 2200M-M

C9A40 181P184070 C-ELEC - 35V 2200M-M

C9A41 181P732010 C-ELEC - 10V 1000M-M 105C

C9A43 172P262050 C-M-POLY - 50V 0.1M-J

C9A45 181P182030 C-ELEC - 16V 1000M-M 105C

C9A46 142P010090 C-CER - B500V 470P-K

C9A47 142P010090 C-CER - B500V 470P-K

C9A51 181P182030 C-ELEC - 16V 1000M-M 105C

C9A52 181P182030 C-ELEC - 16V 1000M-M 105C

C9A61 181P182030 C-ELEC - 16V 1000M-M 105C

C9A62 181P182030 C-ELEC - 16V 1000M-M 105C

C9A64 181P181000 C-ELEC - 10V 330M-M 105C

C9A71 181P183010 C-ELEC - 25V 100M-M

C9A73 181P735020 C-ELEC - 25V 1000M-M 105C

C9A77 181P183010 C-ELEC - 25V 100M-M

C9A79 181P183010 C-ELEC - 25V 100M-M

C9A82 181P183010 C-ELEC - 25V 100M-M

C9AAB 181P351070 C-ELEC - 10V 470M-M

C9ABA 181P352040 C-ELEC - 16V 100M-M

C9B71 181P183010 C-ELEC - 25V 100M-M

C9B73 181P735020 C-ELEC - 25V 1000M-M 105C

C9C01 181P352030 C-ELEC - 16V 47M-M

C9C02 181P352030 C-ELEC - 16V 47M-M

C9C11 181P352030 C-ELEC - 16V 47M-M

C9C12 181P352030 C-ELEC - 16V 47M-M

C9C15 181P355010 C-ELEC - 50V 1M-M

C9C16 189P185070 C-CER - AC250V E1000P-M

C9C17 189P185070 C-CER - AC250V E1000P-M

C9C21 181P352030 C-ELEC - 16V 47M-M

C9C22 181P199080 C-ELEC - 200V 47M-M/Q

C9C22 181P352040 C-ELEC - 16V 100M-M

C9C25 172P262050 C-M-POLY - 50V 0.1M-J

C9C27 154P270050 C-CER - SL1KV 22P-J

C9C28 172P262050 C-M-POLY - 50V 0.1M-J

C9C29 142P010090 C-CER - B500V 470P-K

C9C30 142P010090 C-CER - B500V 470P-K

C9C31 181P743040 C-ELEC - 16V 330M-M

C9C32 181P352040 C-ELEC - 16V 100M-M

C9C33 181P354060 C-ELEC - 35V 100M-M

PAGE 38

[#]

MODEL: WD-52327 / WD-62327



C9C34 181P354060 C-ELEC - 35V 100M-M

C9C35 181P355050 C-ELEC - 50V 10M-M

C9C38 181P355050 C-ELEC - 50V 10M-M

C9C61 181P352030 C-ELEC - 16V 47M-M

C9C62 181P352040 C-ELEC - 16V 100M-M

C9C80 181P355050 C-ELEC - 50V 10M-M

C9C81 181P355050 C-ELEC - 50V 10M-M

C9C82 181P355050 C-ELEC - 50V 10M-M

C9C83 181P352030 C-ELEC - 16V 47M-M

C9C84 181P352030 C-ELEC - 16V 47M-M

C9C85 181P352030 C-ELEC - 16V 47M-M

C9C86 181P352030 C-ELEC - 16V 47M-M

C9C90 181P355050 C-ELEC - 50V 10M-M

C9C91 181P355050 C-ELEC - 50V 10M-M

C9C92 181P355050 C-ELEC - 50V 10M-M

C9C93 181P355050 C-ELEC - 50V 10M-M

C9D00 189P153040 C-M-POLY - 250VAC 0.1M-M

C9D01 189P153040 C-M-POLY - 250VAC 0.1M-M

C9D02 189P153040 C-M-POLY - 250VAC 0.1M-M

C9D03 189P153040 C-M-POLY - 250VAC 0.1M-M

C9D06 189P153040 C-M-POLY - 250VAC 0.1M-M

CF2N10 299P267010 RESONATOR-CER - CSBLA503KECZF30-B0

CF2P10 299P267010 RESONATOR-CER - CSBLA503KECZF30-B0

[#]

SWITCHES

S7L21 432P109010 SW-KEY BOARD - KSHS611BT









MISCELLANEOUS

096Z465080 TAPE-LENS

246C501020 CABLE - DVI to DVI

299P103050 FAN - MMF-04B12-DL-RB1 (Exhaust Fan)

299P278020 FAN - EFB06121A-R00 (Ballast Fan)

299P280010 SENSOR - THERMAL

299P282010 FAN - LAMP

299P283010 FAN - DMD

299P285010 SWITCH - THERMAL

305P702030 2RF-SW

411D044020 CORE-FERRITE - ZCAT2032-0930

411D062010 CORE-FERRITE - ZCAT1518-0730

411D063020 CORE-FERRITE - CAT3035

411P026010 CORE-FERRITE - ZCAT2017

436P021010 SW-MICRO

480P077010 SPEAKER - COAXIAL

592A032020 PLATE-REAR

620D144010 FILTER - DUST

622C208010 MIRROR - HOLDER - TOP

622C208020 MIRROR - HOLDER - TOP

622C209010 MIRROR - HOLDER - BOTTOM

623D252010 MIRROR - HOLDER - BOTTOM

622C220010 COVER - LAMP - VENT

622C247010 COVER-SW

635B114010 MIRROR - BRACKET - TOP a b a b a

Ref # Part # Part Name & Description [#]

635B114020 MIRROR - BRACKET - TOP

635B115010 FRAME-LOCK - PLATE

635B115020 FRAME-LOCK - PLATE

641B991010 MIRROR - HOLDER - SIDE

641B993010 COVER - FRONT

641B999010 MIRROR - HOLDER - SIDE

704B205010 KNOB CONTROL

704B205020 KNOB CONTROL

704B207010 BUTTON - RESET

752B142010 COVER - FILTER

752B143010 COVER - LAMP

761C736010 DOOR

767D075010 MIRROR (52")

767D075020 MIRROR (BIG)

767D076010 MIRROR (SMALL)

915P020010 LAMP - CARTRIDGE

939P977010 OPTICAL-ENGINE

939P977020 OPTICAL-ENGINE

939P978010 UNIT-POWER-LAMP

AG9D00299P220020 SURGE-SUPPRESSOR

F7A00 283P128040 FUSE-CHIP - AC125/100V 3.15A

F7A01 283P128040 FUSE-CHIP - AC125/100V 3.15A

F9A01 283P144080 FUSE - 125V 5A

F9A02 283P144040 FUSE - 32V 15A

F9A03 283P144040 FUSE - 32V 15A

F9A04 283P144080 FUSE - 125V 5A

F9A05 283P144080 FUSE - 125V 5A

F9A06 283P128050 FUSE-CHIP - AC125/100V 4A

F9A07 283P128050 FUSE-CHIP - AC125/100V 4A

F9A08 283P144070 FUSE - 125V 3A

F9A09 283P127060 FUSE-CHIP - AC125/100V 630MA

F9B08 283P144070 FUSE - 125V 3A

F9D00 283D131040 FUSE - S10A 125A

J2AAA 452C385010 CONNECTOR-DVI

J8E00 452C385010 CONNECTOR-DVI

K9A10 287P111010 RELAY-POWER - LKS1AF-5V

K9A11 287P111010 RELAY-POWER - LKS1AF-5V a b a b



PC9A10 268P058020 PHOTO-COUPLER - ON3131-R/ON3161-R

PC9A21 268P058020 PHOTO-COUPLER - ON3131-R/ON3161-R

PC9C50 268P058020 PHOTO-COUPLER - ON3131-R/ON3161-R

PJ2J00 440C407010 PIN-JACK-BOARD-6P




PJ2J04 440C430050 PIN-JACK-BOARD

PJ2J05 440C439010 PIN-JACK-BOARD 3P

PJ2J06 440C430040 PIN-JACK-BOARD


TU1A01 295P516010 TUNER-TV - 115-V-F045AP

TU1B01 295P516020 TUNER-TV - 115-V-F025AP

X2M47 285P426040 QTZ-CRYST - 20.000MHZ

X2N21 285P426010 QTZ-CRYST - 3.579545MHZ

X2P21 285P426010 QTZ-CRYST - 3.579545MHZ

X3A01 285P413010 QTZ-CRYST - 18.432MHZ

X7A13 285P434020 QTZ-CRYST - 16.000MHZ

X7J10 285P335050 QTZ-CRYST - 80.000MHZ

X8C02 285P391030 OSC - 74.175824MHZ

Z7K01 939P617010 UNIT-PREAMP - GP1U283Q b a b a b a b

PAGE 39



MODEL: WD-52327 / WD-62327


PRINTED CIRCUIT BOARDS

930B929001 ASSY-PWB-POWER

930B930001 ASSY-PWB-SIGNAL

930B931001 ASSY-PWB-FMT

930B932001 ASSY-PWB-TERMINAL

934C148001 ASSY-PWB-POWER-SUB

934C149001 ASSY-PWB-AUDIO

935D811001 ASSY-PWB-PREAMP

935D812001 ASSY-PWB-FRONT

935D813001 ASSY-PWB-CONTROL

935D814001 ASSY-PWB-SPEAKER-R

935D815001 ASSY-PWB-SPEAKER-L

955B310001 ASSY-CHASSIS

COSMETIC PARTS

760A016010 INLAY TERMINAL

761A233010 GRILLE - SPEAKER

761A239010 GRILLE - SPEAKER

775B142080 NAME-PLATE - WD-52327

775B142090 NAME-PLATE - WD-62327

850C095010 INLAY FRONT

ACCESSORIES

246C351050 CORD-AC - POWER

290P116010 REMOTE CONTROL - V22/V24

I/QR WD5237 GUIDE - QR - VK26

I/B WD52327 GUIDE - OWNERS - VK26 a b a b

[#]

PAGE 40

MODEL: WD-52327 / WD-62327



(8)

(9)

(10)

(11)

(5)

(12)

(13)

(6)

(7)

SCREEN ASSEMBLY PARTS

WD-52327

(1)

(2)

(3)

(4)

491P175010 LENS-FRESNEL

491P176030 SCREEN-LENTICULAR

623D174010 SCREEN - HOLDER

701B499050 SCREEN FRAME - TOP

701B517050 SCREEN FRAME - SIDE

704B206010 SCREEN - TRIM - LEFT

704B206020 SCREEN - TRIM - RIGHT

761A232030 SCREEN FRAME - BOTTOM

761A238030 SCREEN COVER - TOP

768C082010 SCREEN-CAP-CORNER - LEFT

768C082020 SCREEN-CAP-CORNER - RIGHT

761A252010 BEZEL - FRONT

623D209010 SHEET-BOTTOM

WD-62327

(14)

(15)

(6)

(7)

(8)

(1)

(2)

(3)

(4)

(5)

(9)

(10)

(11)

491P175020 LENS-FRESNEL

491P176040 SCREEN-LENTICULAR

623D253010 SCREEN - HOLDER

701B525010 SCREEN FRAME - TOP

701B526030 SCREEN FRAME - SIDE

704B208010 SCREEN - TRIM - LEFT

704B208020 SCREEN - TRIM - RIGHT

761A242030 SCREEN FRAME - BOTTOM

761A244030 SCREEN FRAME - TOP COVER

768C082010 SCREEN-CAP-CORNER - LEFT

768C082020 SCREEN-CAP-CORNER - RIGHT

761A253010 BEZEL - FRONT

623D209020 SHEET-BOTTOM

[#]

PAGE 41

MODEL: WD-52327 / WD-62327

Page 42

MODEL: WD-52327 / WD-62327

Page 43

MODEL: WD-52327 / WD-62327

Page 44

MODEL: WD-52327 / WD-62327

Page 45

MODEL: WD-52327 / WD-62327

Page 46

MODEL: WD-52327 / WD-62327

Page 47

MODEL: WD-52327 / WD-62327

Page 48

MODEL: WD-52327 / WD-62327

Page 49

MODEL: WD-52327 / WD-62327

Page 50

No results